[U-Boot] [PATCH 5/6 v2] 8xx, mgsuvd: rename board to a more generic name
Heiko Schocher
hs at denx.de
Thu Mar 12 07:37:28 CET 2009
renaming the "mgsuvd" board port into "km8xx", because
there come more similar boards from keymile.
Compiling the mgsuvd board with "make mgsuvd_config"
remains.
Signed-off-by: Heiko Schocher <hs at denx.de>
---
Makefile | 2 +-
board/keymile/common/common.c | 2 +-
board/keymile/common/keymile_hdlc_enet.h | 2 +-
board/keymile/{mgsuvd => km8xx}/Makefile | 2 +-
board/keymile/{mgsuvd => km8xx}/config.mk | 0
board/keymile/{mgsuvd/mgsuvd.c => km8xx/km8xx.c} | 0
.../mgsuvd_hdlc_enet.c => km8xx/km8xx_hdlc_enet.c} | 0
board/keymile/{mgsuvd => km8xx}/u-boot.lds | 0
include/commproc.h | 8 +-
include/configs/km8xx.h | 317 ++++++++++++++++++++
include/configs/mgsuvd.h | 285 +-----------------
11 files changed, 327 insertions(+), 291 deletions(-)
rename board/keymile/{mgsuvd => km8xx}/Makefile (98%)
rename board/keymile/{mgsuvd => km8xx}/config.mk (100%)
rename board/keymile/{mgsuvd/mgsuvd.c => km8xx/km8xx.c} (100%)
rename board/keymile/{mgsuvd/mgsuvd_hdlc_enet.c => km8xx/km8xx_hdlc_enet.c} (100%)
rename board/keymile/{mgsuvd => km8xx}/u-boot.lds (100%)
create mode 100644 include/configs/km8xx.h
diff --git a/Makefile b/Makefile
index e8b4c13..8cc8dd5 100644
--- a/Makefile
+++ b/Makefile
@@ -938,7 +938,7 @@ MBX860T_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc8xx mbx8xx
mgsuvd_config: unconfig
- @$(MKCONFIG) $(@:_config=) ppc mpc8xx mgsuvd keymile
+ @$(MKCONFIG) $(@:_config=) ppc mpc8xx km8xx keymile
MHPC_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc8xx mhpc eltec
diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c
index 48ce613..c3fa844 100644
--- a/board/keymile/common/common.c
+++ b/board/keymile/common/common.c
@@ -390,7 +390,7 @@ static void setports (int gpio)
#endif
#endif
-#if defined(CONFIG_MGSUVD)
+#if defined(CONFIG_KM8XX)
static void set_sda (int state)
{
I2C_SDA(state);
diff --git a/board/keymile/common/keymile_hdlc_enet.h b/board/keymile/common/keymile_hdlc_enet.h
index 965bd5a..db1560f 100644
--- a/board/keymile/common/keymile_hdlc_enet.h
+++ b/board/keymile/common/keymile_hdlc_enet.h
@@ -25,7 +25,7 @@
#define _KEYMILE_HDLC_ENET_H_
/* Unfortuantely, we have do this to get the flag defines in the cbd_t */
-#ifdef CONFIG_MGSUVD
+#ifdef CONFIG_KM8XX
#include <commproc.h>
#endif
#ifdef CONFIG_MGCOGE
diff --git a/board/keymile/mgsuvd/Makefile b/board/keymile/km8xx/Makefile
similarity index 98%
rename from board/keymile/mgsuvd/Makefile
rename to board/keymile/km8xx/Makefile
index 2c5732d..a6f3241 100644
--- a/board/keymile/mgsuvd/Makefile
+++ b/board/keymile/km8xx/Makefile
@@ -29,7 +29,7 @@ endif
LIB = $(obj)lib$(BOARD).a
COBJS = $(BOARD).o ../common/common.o ../common/keymile_hdlc_enet.o \
- mgsuvd_hdlc_enet.o
+ km8xx_hdlc_enet.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
diff --git a/board/keymile/mgsuvd/config.mk b/board/keymile/km8xx/config.mk
similarity index 100%
rename from board/keymile/mgsuvd/config.mk
rename to board/keymile/km8xx/config.mk
diff --git a/board/keymile/mgsuvd/mgsuvd.c b/board/keymile/km8xx/km8xx.c
similarity index 100%
rename from board/keymile/mgsuvd/mgsuvd.c
rename to board/keymile/km8xx/km8xx.c
diff --git a/board/keymile/mgsuvd/mgsuvd_hdlc_enet.c b/board/keymile/km8xx/km8xx_hdlc_enet.c
similarity index 100%
rename from board/keymile/mgsuvd/mgsuvd_hdlc_enet.c
rename to board/keymile/km8xx/km8xx_hdlc_enet.c
diff --git a/board/keymile/mgsuvd/u-boot.lds b/board/keymile/km8xx/u-boot.lds
similarity index 100%
rename from board/keymile/mgsuvd/u-boot.lds
rename to board/keymile/km8xx/u-boot.lds
diff --git a/include/commproc.h b/include/commproc.h
index 12decfe..9d28abc 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -1122,11 +1122,11 @@ typedef struct scc_enet {
#define SICR_ENET_CLKRT ((uint)0x0000003d)
#endif /* CONFIG_MBX */
-/*** MGSUVD *********************************************************/
+/*** KM8XX *********************************************************/
-/* The MGSUVD Service Module uses SCC3 for Ethernet */
+/* The KM8XX Service Module uses SCC3 for Ethernet */
-#ifdef CONFIG_MGSUVD
+#ifdef CONFIG_KM8XX
#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
#define CPM_CR_ENET CPM_CR_CH_SCC3
#define SCC_ENET 2
@@ -1145,7 +1145,7 @@ typedef struct scc_enet {
*/
#define SICR_ENET_MASK ((uint)0x00FF0000)
#define SICR_ENET_CLKRT ((uint)0x00250000)
-#endif /* CONFIG_MGSUVD */
+#endif /* CONFIG_KM8XX */
/*** MHPC ********************************************************/
diff --git a/include/configs/km8xx.h b/include/configs/km8xx.h
new file mode 100644
index 0000000..a29771f
--- /dev/null
+++ b/include/configs/km8xx.h
@@ -0,0 +1,317 @@
+/*
+ * (C) Copyright 2009
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * configuration options, keymile 8xx board specific
+ */
+
+#ifndef __CONFIG_KM8XX_H
+#define __CONFIG_KM8XX_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_KM8XX 1 /* on a km8xx board */
+
+/* include common defines/options for all Keymile boards */
+#include "keymile-common.h"
+
+#define CONFIG_8xx_GCLK_FREQ 66000000
+
+#define CONFIG_SYS_SMC_UCODE_PATCH 1 /* Relocate SMC1 */
+#define CONFIG_SYS_SMC_DPMEM_OFFSET 0x1fc0
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#define CONFIG_SYS_SMC_RXBUFLEN 128
+#define CONFIG_SYS_MAXIDLE 10
+
+#define CONFIG_SYS_CPM_BOOTCOUNT_ADDR 0x1eb0 /* In case of SMC relocation,
+ * the default value is not
+ * working
+ */
+
+#define BOOTFLASH_START F0000000
+#define CONFIG_PRAM 512 /* protected RAM [KBytes] */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
+ "echo"
+
+#define BOOTFLASH_START F0000000
+#define CONFIG_PRAM 512 /* protected RAM [KBytes] */
+
+#define CONFIG_ENV_IVM "EEprom_ivm=pca9544a:70:4 \0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_KM_DEF_ENV \
+ "rootpath=/opt/eldk/ppc_8xx\0" \
+ "addcon=setenv bootargs ${bootargs} " \
+ "console=ttyCPM0,${baudrate}\0" \
+ "mtdids=nor0=app \0" \
+ "mtdparts=mtdparts=app:384k(u-boot),128k(env),128k(envred)," \
+ "128k(free),1536k(esw0),8704k(rootfs0),1536k(esw1)," \
+ "2432k(rootfs1),640k(var),768k(cfg)\0" \
+ "partition=nor0,9 \0" \
+ "new_env=prot off F0060000 F009FFFF; era F0060000 F009FFFF \0" \
+ CONFIG_ENV_IVM \
+ ""
+
+#undef CONFIG_RTC_MPC8xx /* MPC866 does not support RTC */
+
+#define CONFIG_TIMESTAMP /* but print image timestmps */
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CONFIG_SYS_IMMR 0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 64
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xf0000000
+#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* 384 kB for Monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* 256 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+/* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_FLASH_SIZE 32
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+/* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* (in ms) */
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN
+#define CONFIG_ENV_SIZE 0x04000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#define CONFIG_ENV_BUFFER_PRINT 1
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#define CONFIG_SYS_SYPCR 0xffffff89
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_SIUMCR 0x00610480
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK 0x01800000
+#define CONFIG_SYS_SCCR 0x01800000
+
+#define CONFIG_SYS_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0xf0000000 /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
+
+/*
+ * FLASH timing: Default value of OR0 after reset
+ */
+#define CONFIG_SYS_OR0_PRELIM 0xfe000954
+#define CONFIG_SYS_BR0_PRELIM 0xf0000401
+
+/*
+ * BR1 and OR1 (SDRAM)
+ *
+ */
+#define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank #0 */
+#define SDRAM_MAX_SIZE (64 << 20) /* max 64 MB per bank */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
+
+#define CONFIG_SYS_OR1_PRELIM 0xfc000800
+#define CONFIG_SYS_BR1_PRELIM (0x000000C0 | 0x01)
+
+#define CONFIG_SYS_MPTPR 0x0200
+/* PTB=16, AMB=001, FIXME 1 RAS precharge cycles, 1 READ loop cycle (not used),
+ 1 Write loop Cycle (not used), 1 Timer Loop Cycle */
+#define CONFIG_SYS_MBMR 0x10964111
+#define CONFIG_SYS_MAR 0x00000088
+
+/*
+ * 4096 Rows from SDRAM example configuration
+ * 1000 factor s -> ms
+ * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
+ * 4 Number of refresh cycles per period
+ * 64 Refresh cycle in ms per number of rows
+ */
+#define CONFIG_SYS_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
+
+/* GPIO/PIGGY on CS3 initialization values
+*/
+#define CONFIG_SYS_PIGGY_BASE (0x30000000)
+#define CONFIG_SYS_OR3_PRELIM (0xfe000d24)
+#define CONFIG_SYS_BR3_PRELIM (0x30000401)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#define CONFIG_SCC3_ENET
+#define CONFIG_ETHPRIME "SCC ETHERNET"
+#define CONFIG_HAS_ETH0
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#define OF_STDOUT_PATH "/soc/cpm/serial at a80"
+
+/* enable I2C and select the hardware/software driver */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SPEED 50000
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define I2C_SOFT_DECLARATIONS
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define I2C_BASE_DIR ((u16 *)(CONFIG_SYS_PIGGY_BASE + 0x04))
+#define I2C_BASE_PORT ((u8 *)(CONFIG_SYS_PIGGY_BASE + 0x09))
+
+#define SDA_BIT 0x40
+#define SCL_BIT 0x80
+#define SDA_CONF 0x1000
+#define SCL_CONF 0x2000
+
+#define I2C_ACTIVE do {} while (0)
+#define I2C_TRISTATE do {} while (0)
+#define I2C_READ ((in_8(I2C_BASE_PORT) & SDA_BIT) == SDA_BIT)
+#define I2C_SDA(bit) if(bit) { \
+ clrbits(be16, I2C_BASE_DIR, SDA_CONF); \
+ } else { \
+ clrbits(8, I2C_BASE_PORT, SDA_BIT); \
+ setbits(be16, I2C_BASE_DIR, SDA_CONF); \
+ }
+#define I2C_SCL(bit) if(bit) { \
+ clrbits(be16, I2C_BASE_DIR, SCL_CONF); \
+ } else { \
+ clrbits(8, I2C_BASE_PORT, SCL_BIT); \
+ setbits(be16, I2C_BASE_DIR, SCL_CONF); \
+ }
+#define I2C_DELAY udelay(50) /* 1/4 I2C clock duration */
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible) */
+#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_SENSORS {0, 2, 4, 6} /* Sensor addresses */
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
+#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS)
+
+#define MTDIDS_DEFAULT "nor0=app"
+#define MTDPARTS_DEFAULT ( \
+ "mtdparts=app:384k(u-boot),128k(env),128k(envred),128k(free)," \
+ "1536k(esw0),8704k(rootfs0),1536k(esw1),2432k(rootfs1),640k(var)," \
+ "768k(cfg)")
+
+#endif /* __CONFIG_KM8XX_H */
diff --git a/include/configs/mgsuvd.h b/include/configs/mgsuvd.h
index c8679e7..1618f7d 100644
--- a/include/configs/mgsuvd.h
+++ b/include/configs/mgsuvd.h
@@ -28,292 +28,11 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
#define CONFIG_MPC866 1 /* This is a MPC866 CPU */
#define CONFIG_MGSUVD 1 /* ...on a mgsuvd board */
#define CONFIG_HOSTNAME mgsuvd
-/* include common defines/options for all Keymile boards */
-#include "keymile-common.h"
-
-#define CONFIG_8xx_GCLK_FREQ 66000000
-
-#define CONFIG_SYS_SMC_UCODE_PATCH 1 /* Relocate SMC1 */
-#define CONFIG_SYS_SMC_DPMEM_OFFSET 0x1fc0
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_SYS_CPM_BOOTCOUNT_ADDR 0x1eb0 /* In case of SMC relocation,
- * the default value is not
- * working
- */
-
-#define BOOTFLASH_START F0000000
-#define CONFIG_PRAM 512 /* protected RAM [KBytes] */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#define BOOTFLASH_START F0000000
-#define CONFIG_PRAM 512 /* protected RAM [KBytes] */
-
-#define CONFIG_ENV_IVM "EEprom_ivm=pca9544a:70:4 \0"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "addcon=setenv bootargs ${bootargs} " \
- "console=ttyCPM0,${baudrate}\0" \
- "mtdids=nor0=app \0" \
- "mtdparts=mtdparts=app:384k(u-boot),128k(env),128k(envred)," \
- "128k(free),1536k(esw0),8704k(rootfs0),1536k(esw1)," \
- "2432k(rootfs1),640k(var),768k(cfg)\0" \
- "partition=nor0,9 \0" \
- "new_env=prot off F0060000 F009FFFF; era F0060000 F009FFFF \0" \
- CONFIG_ENV_IVM \
- ""
-
-#undef CONFIG_RTC_MPC8xx /* MPC866 does not support RTC */
-
-#define CONFIG_TIMESTAMP /* but print image timestmps */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 64
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xf0000000
-#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* 384 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* 256 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_FLASH_SIZE 32
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-/* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_SECT 256
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* (in ms) */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN
-#define CONFIG_ENV_SIZE 0x04000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-#define CONFIG_ENV_BUFFER_PRINT 1
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#define CONFIG_SYS_SYPCR 0xffffff89
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR 0x00610480
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK 0x01800000
-#define CONFIG_SYS_SCCR 0x01800000
-
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0xf0000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing: Default value of OR0 after reset
- */
-#define CONFIG_SYS_OR0_PRELIM 0xfe000954
-#define CONFIG_SYS_BR0_PRELIM 0xf0000401
-
-/*
- * BR1 and OR1 (SDRAM)
- *
- */
-#define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_MAX_SIZE (64 << 20) /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR1_PRELIM 0xfc000800
-#define CONFIG_SYS_BR1_PRELIM (0x000000C0 | 0x01)
-
-#define CONFIG_SYS_MPTPR 0x0200
-/* PTB=16, AMB=001, FIXME 1 RAS precharge cycles, 1 READ loop cycle (not used),
- 1 Write loop Cycle (not used), 1 Timer Loop Cycle */
-#define CONFIG_SYS_MBMR 0x10964111
-#define CONFIG_SYS_MAR 0x00000088
-
-/*
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- */
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
-
-/* GPIO/PIGGY on CS3 initialization values
-*/
-#define CONFIG_SYS_PIGGY_BASE (0x30000000)
-#define CONFIG_SYS_OR3_PRELIM (0xfe000d24)
-#define CONFIG_SYS_BR3_PRELIM (0x30000401)
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#define CONFIG_SCC3_ENET
-#define CONFIG_ETHPRIME "SCC ETHERNET"
-#define CONFIG_HAS_ETH0
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#define OF_STDOUT_PATH "/soc/cpm/serial at a80"
-
-/* enable I2C and select the hardware/software driver */
-#undef CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED 50000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define I2C_SOFT_DECLARATIONS
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define I2C_BASE_DIR ((u16 *)(CONFIG_SYS_PIGGY_BASE + 0x04))
-#define I2C_BASE_PORT ((u8 *)(CONFIG_SYS_PIGGY_BASE + 0x09))
-
-#define SDA_BIT 0x40
-#define SCL_BIT 0x80
-#define SDA_CONF 0x1000
-#define SCL_CONF 0x2000
-
-#define I2C_ACTIVE do {} while (0)
-#define I2C_TRISTATE do {} while (0)
-#define I2C_READ ((in_8(I2C_BASE_PORT) & SDA_BIT) == SDA_BIT)
-#define I2C_SDA(bit) if(bit) { \
- clrbits(be16, I2C_BASE_DIR, SDA_CONF); \
- } else { \
- clrbits(8, I2C_BASE_PORT, SDA_BIT); \
- setbits(be16, I2C_BASE_DIR, SDA_CONF); \
- }
-#define I2C_SCL(bit) if(bit) { \
- clrbits(be16, I2C_BASE_DIR, SCL_CONF); \
- } else { \
- clrbits(8, I2C_BASE_PORT, SCL_BIT); \
- setbits(be16, I2C_BASE_DIR, SCL_CONF); \
- }
-#define I2C_DELAY udelay(50) /* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0, 2, 4, 6} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS)
-
-#define MTDIDS_DEFAULT "nor0=app"
-#define MTDPARTS_DEFAULT ( \
- "mtdparts=app:384k(u-boot),128k(env),128k(envred),128k(free)," \
- "1536k(esw0),8704k(rootfs0),1536k(esw1),2432k(rootfs1),640k(var)," \
- "768k(cfg)")
+/* include common defines/options for all Keymile 8xx boards */
+#include "km8xx.h"
#endif /* __CONFIG_H */
--
1.6.0.6
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
More information about the U-Boot
mailing list