[U-Boot] [PATCH] inka4x0: Use proper accessor macros for memory mapped registers.
Detlev Zundel
dzu at denx.de
Tue Mar 24 18:02:38 CET 2009
Signed-off-by: Detlev Zundel <dzu at denx.de>
---
board/inka4x0/inka4x0.c | 131 ++++++++++++++++++++++++-----------------------
1 files changed, 67 insertions(+), 64 deletions(-)
diff --git a/board/inka4x0/inka4x0.c b/board/inka4x0/inka4x0.c
index 35747ed..2ef770b 100644
--- a/board/inka4x0/inka4x0.c
+++ b/board/inka4x0/inka4x0.c
@@ -55,41 +55,34 @@
#ifndef CONFIG_SYS_RAMBOOT
static void sdram_start (int hi_addr)
{
+ struct mpc5xxx_sdram *sdram = (struct mpc5xxx_sdram *)MPC5XXX_SDRAM;
long hi_addr_bit = hi_addr ? 0x01000000 : 0;
/* unlock mode register */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
- __asm__ volatile ("sync");
+ out_be32(&sdram->ctrl, SDRAM_CONTROL | 0x80000000 | hi_addr_bit);
/* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
+ out_be32(&sdram->ctrl, SDRAM_CONTROL | 0x80000002 | hi_addr_bit);
#if SDRAM_DDR
/* set mode register: extended mode */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
- __asm__ volatile ("sync");
+ out_be32(&sdram->mode, SDRAM_EMODE);
/* set mode register: reset DLL */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
- __asm__ volatile ("sync");
+ out_be32(&sdram->mode, SDRAM_MODE | 0x04000000);
#endif
/* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
- __asm__ volatile ("sync");
+ out_be32(&sdram->ctrl, SDRAM_CONTROL | 0x80000002 | hi_addr_bit);
/* auto refresh */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
- __asm__ volatile ("sync");
+ out_be32(&sdram->ctrl, SDRAM_CONTROL | 0x80000004 | hi_addr_bit);
/* set mode register */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
- __asm__ volatile ("sync");
+ out_be32(&sdram->mode, SDRAM_MODE);
/* normal operation */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
- __asm__ volatile ("sync");
+ out_be32(&sdram->ctrl, SDRAM_CONTROL | hi_addr_bit);
}
#endif
@@ -101,24 +94,24 @@ static void sdram_start (int hi_addr)
phys_size_t initdram (int board_type)
{
+ struct mpc5xxx_mmap_ctl *mm = (struct mpc5xxx_mmap_ctl *) CONFIG_SYS_MBAR;
+ struct mpc5xxx_cdm *cdm = (struct mpc5xxx_cdm *) MPC5XXX_CDM;
+ struct mpc5xxx_sdram *sdram = (struct mpc5xxx_sdram *) MPC5XXX_SDRAM;
ulong dramsize = 0;
#ifndef CONFIG_SYS_RAMBOOT
long test1, test2;
/* setup SDRAM chip selects */
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001c; /* 512MB at 0x0 */
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x40000000; /* disabled */
- __asm__ volatile ("sync");
+ out_be32(&mm->sdram0, 0x0000001c); /* 512MB at 0x0 */
+ out_be32(&mm->sdram1, 0x40000000); /* disabled */
/* setup config registers */
- *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
- *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
- __asm__ volatile ("sync");
+ out_be32(&sdram->config1, SDRAM_CONFIG1);
+ out_be32(&sdram->config2, SDRAM_CONFIG2);
#if SDRAM_DDR
/* set tap delay */
- *(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
- __asm__ volatile ("sync");
+ out_be32(&cdm->porcfg, SDRAM_TAPDELAY);
#endif
/* find RAM size using SDRAM CS0 only */
@@ -140,17 +133,17 @@ phys_size_t initdram (int board_type)
/* set SDRAM CS0 size according to the amount of RAM found */
if (dramsize > 0) {
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 +
- __builtin_ffs(dramsize >> 20) - 1;
+ out_be32(&mm->sdram0, 0x13 +
+ __builtin_ffs(dramsize >> 20) - 1);
} else {
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
+ out_be32(&mm->sdram0, 0); /* disabled */
}
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
+ out_be32(&mm->sdram1, dramsize); /* disabled */
#else /* CONFIG_SYS_RAMBOOT */
/* retrieve size of memory connected to SDRAM CS0 */
- dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
+ dramsize = in_be32(&mm->sdram0) & 0xFF;
if (dramsize >= 0x13) {
dramsize = (1 << (dramsize - 0x13)) << 20;
} else {
@@ -169,13 +162,15 @@ int checkboard (void)
void flash_preinit(void)
{
+ struct mpc5xxx_lpb *lpb = (struct mpc5xxx_lpb *)MPC5XXX_LPB;
+
/*
* Now, when we are in RAM, enable flash write
* access for detection process.
- * Note that CS_BOOT cannot be cleared when
+ * Note that CS_BOOT (CS0) cannot be cleared when
* executing in flash.
*/
- *(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
+ clrbits_be32(&lpb->cs0_cfg, 0x1); /* clear RO */
}
int misc_init_r (void) {
@@ -189,8 +184,9 @@ int misc_init_r (void) {
int misc_init_f (void)
{
- struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
- struct mpc5xxx_wu_gpio *wu_gpio = (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
+ struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *) MPC5XXX_GPIO;
+ struct mpc5xxx_wu_gpio *wu_gpio = (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
+ struct mpc5xxx_gpt *gpt;
char tmp[10];
int i, br;
@@ -204,40 +200,43 @@ int misc_init_f (void)
/* Initialize GPIO output pins.
*/
/* Configure GPT as GPIO output (and set them as they control low-active LEDs */
- *(vu_long *)MPC5XXX_GPT0_ENABLE =
- *(vu_long *)MPC5XXX_GPT1_ENABLE =
- *(vu_long *)MPC5XXX_GPT2_ENABLE =
- *(vu_long *)MPC5XXX_GPT3_ENABLE =
- *(vu_long *)MPC5XXX_GPT4_ENABLE =
- *(vu_long *)MPC5XXX_GPT5_ENABLE = 0x34;
+ for (i = 0; i <= 5; i++) {
+ gpt = (struct mpc5xxx_gpt *)(MPC5XXX_GPT + (i * 0x10));
+ out_be32(&gpt->emsr, 0x34);
+ }
/* Configure GPT7 as PWM timer, 1kHz, no ints. */
- *(vu_long *)MPC5XXX_GPT7_ENABLE = 0;/* Disable */
- *(vu_long *)MPC5XXX_GPT7_COUNTER = 0x020000fe;
- *(vu_long *)MPC5XXX_GPT7_PWMCFG = (br << 16);
- *(vu_long *)MPC5XXX_GPT7_ENABLE = 0x3;/* Enable PWM mode and start */
+ gpt = (struct mpc5xxx_gpt *)(MPC5XXX_GPT + (7 * 0x10));
+ out_be32(&gpt->emsr, 0); /* Disable */
+ out_be32(&gpt->cir, 0x020000fe);
+ out_be32(&gpt->pwmcr, (br << 16));
+ out_be32(&gpt->emsr, 0x3); /* Enable PWM mode and start */
/* Configure PSC3_6,7 as GPIO output */
- *(vu_long *)MPC5XXX_GPIO_ENABLE |= 0x00003000;
- *(vu_long *)MPC5XXX_GPIO_DIR |= 0x00003000;
-
- /* Configure PSC3_8 as GPIO output, no interrupt */
- *(vu_long *)MPC5XXX_GPIO_SI_ENABLE |= 0x04000000;
- *(vu_long *)MPC5XXX_GPIO_SI_DIR |= 0x04000000;
- *(vu_long *)MPC5XXX_GPIO_SI_IEN &= ~0x04000000;
+ setbits_be32(&gpio->simple_gpioe, MPC5XXX_GPIO_SIMPLE_PSC3_6 |
+ MPC5XXX_GPIO_SIMPLE_PSC3_7);
+ setbits_be32(&gpio->simple_ddr, MPC5XXX_GPIO_SIMPLE_PSC3_6 |
+ MPC5XXX_GPIO_SIMPLE_PSC3_7);
/* Configure PSC3_9 and GPIO_WKUP6,7 as GPIO output */
- *(vu_long *)MPC5XXX_WU_GPIO_ENABLE |= 0xc4000000;
- *(vu_long *)MPC5XXX_WU_GPIO_DIR |= 0xc4000000;
+ setbits_8(&wu_gpio->enable, MPC5XXX_GPIO_WKUP_6 |
+ MPC5XXX_GPIO_WKUP_7 |
+ MPC5XXX_GPIO_WKUP_PSC3_9);
+ setbits_8(&wu_gpio->ddr, MPC5XXX_GPIO_WKUP_6 |
+ MPC5XXX_GPIO_WKUP_7 |
+ MPC5XXX_GPIO_WKUP_PSC3_9);
/* Set LR mirror bit because it is low-active */
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_WKUP_7;
- /*
- * Reset Coral-P graphics controller
- */
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC3_9;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC3_9;
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC3_9;
+ setbits_8(&wu_gpio->dvo, MPC5XXX_GPIO_WKUP_7);
+
+ /* Reset Coral-P graphics controller */
+ setbits_8(&wu_gpio->dvo, MPC5XXX_GPIO_WKUP_PSC3_9);
+
+ /* Enable display backlight */
+ clrbits_8(&gpio->sint_inten, MPC5XXX_GPIO_SINT_PSC3_8);
+ setbits_8(&gpio->sint_gpioe, MPC5XXX_GPIO_SINT_PSC3_8);
+ setbits_8(&gpio->sint_ddr, MPC5XXX_GPIO_SINT_PSC3_8);
+ setbits_8(&gpio->sint_dvo, MPC5XXX_GPIO_SINT_PSC3_8);
/*
* Configure three wire serial interface to RTC (PSC1_4,
@@ -273,25 +272,29 @@ void pci_init_board(void)
void init_ide_reset (void)
{
+ struct mpc5xxx_wu_gpio *wu_gpio = (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
+
debug ("init_ide_reset\n");
/* Configure PSC1_4 as GPIO output for ATA reset */
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
+ setbits_8(&wu_gpio->enable, MPC5XXX_GPIO_WKUP_PSC1_4);
+ setbits_8(&wu_gpio->ddr, MPC5XXX_GPIO_WKUP_PSC1_4);
/* Deassert reset */
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
+ setbits_8(&wu_gpio->dvo, MPC5XXX_GPIO_WKUP_PSC1_4);
}
void ide_set_reset (int idereset)
{
+ struct mpc5xxx_wu_gpio *wu_gpio = (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
+
debug ("ide_reset(%d)\n", idereset);
if (idereset) {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
+ clrbits_8(&wu_gpio->dvo, MPC5XXX_GPIO_WKUP_PSC1_4);
/* Make a delay. MPC5200 spec says 25 usec min */
udelay(500000);
} else {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
+ setbits_8(&wu_gpio->dvo, MPC5XXX_GPIO_WKUP_PSC1_4);
}
}
#endif
--
1.6.0.6
More information about the U-Boot
mailing list