[U-Boot] [PATCH 2/6] ZOOM2 Add initial support for Zoom2
Tom Rix
Tom.Rix at windriver.com
Thu May 7 23:28:02 CEST 2009
Zoom2 is a new board from Texas Instruments and LogicPD
The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com
This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is the product description web page
http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp
This patch provides a zoom2 base target by copying zoom1 and by making some
obvious changes.
To configure, run
make omap3_zoom2_config
Signed-off-by: Tom Rix <Tom.Rix at windriver.com>
---
MAINTAINERS | 4 +
MAKEALL | 1 +
Makefile | 3 +
board/omap3/common/Makefile | 1 +
board/omap3/zoom2/Makefile | 49 +++++++++
board/omap3/zoom2/config.mk | 33 ++++++
board/omap3/zoom2/zoom2.c | 76 ++++++++++++++
board/omap3/zoom2/zoom2.h | 149 +++++++++++++++++++++++++++
doc/README.omap3 | 15 +++-
include/configs/omap3_zoom2.h | 226 +++++++++++++++++++++++++++++++++++++++++
10 files changed, 555 insertions(+), 2 deletions(-)
create mode 100644 board/omap3/zoom2/Makefile
create mode 100644 board/omap3/zoom2/config.mk
create mode 100644 board/omap3/zoom2/zoom2.c
create mode 100644 board/omap3/zoom2/zoom2.h
create mode 100644 include/configs/omap3_zoom2.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 6bb03b4..e19fd0f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -615,6 +615,10 @@ Stelian Pop <stelian.pop at leadtechdesign.com>
at91sam9263ek ARM926EJS (AT91SAM9263 SoC)
at91sam9rlek ARM926EJS (AT91SAM9RL SoC)
+Tom Rix <Tom.Rix at windriver.com>
+
+ omap3_zoom2 ARM CORTEX-A8 (OMAP3xx SoC)
+
Stefan Roese <sr at denx.de>
ixdpg425 xscale
diff --git a/MAKEALL b/MAKEALL
index f13c81a..46a96c0 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -561,6 +561,7 @@ LIST_ARM_CORTEX_A8=" \
omap3_evm \
omap3_pandora \
omap3_zoom1 \
+ omap3_zoom2 \
"
#########################################################################
diff --git a/Makefile b/Makefile
index 137c88f..9d107e6 100644
--- a/Makefile
+++ b/Makefile
@@ -2983,6 +2983,9 @@ omap3_pandora_config : unconfig
omap3_zoom1_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 zoom1 omap3 omap3
+omap3_zoom2_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 zoom2 omap3 omap3
+
#########################################################################
## XScale Systems
#########################################################################
diff --git a/board/omap3/common/Makefile b/board/omap3/common/Makefile
index 7b892fa..b8a0b14 100644
--- a/board/omap3/common/Makefile
+++ b/board/omap3/common/Makefile
@@ -33,6 +33,7 @@ COBJS-$(CONFIG_OMAP3_BEAGLE) += power.o
COBJS-$(CONFIG_OMAP3_OVERO) += power.o
COBJS-$(CONFIG_OMAP3_PANDORA) += power.o
COBJS-$(CONFIG_OMAP3_ZOOM1) += power.o
+COBJS-$(CONFIG_OMAP3_ZOOM2) += power.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
diff --git a/board/omap3/zoom2/Makefile b/board/omap3/zoom2/Makefile
new file mode 100644
index 0000000..088b8cb
--- /dev/null
+++ b/board/omap3/zoom2/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := zoom2.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/omap3/zoom2/config.mk b/board/omap3/zoom2/config.mk
new file mode 100644
index 0000000..33f394b
--- /dev/null
+++ b/board/omap3/zoom2/config.mk
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2009
+# Texas Instruments, <www.ti.com>
+#
+# Zoom II uses OMAP3 (ARM-CortexA8) CPU
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 0x80000000 (bank0)
+# 0xA0000000 (bank1)
+# Linux-Kernel is expected to be at 0x80008000, entry 0x80008000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
diff --git a/board/omap3/zoom2/zoom2.c b/board/omap3/zoom2/zoom2.c
new file mode 100644
index 0000000..0700c56
--- /dev/null
+++ b/board/omap3/zoom2/zoom2.c
@@ -0,0 +1,76 @@
+/*
+ * Copyright (c) 2009 Wind River Systems, Inc.
+ * Tom Rix <Tom.Rix at windriver.com>
+ *
+ * Derived from Zoom1 code by
+ * Nishanth Menon <nm at ti.com>
+ * Sunil Kumar <sunilsaini05 at gmail.com>
+ * Shashi Ranjan <shashiranjanmca05 at gmail.com>
+ * Richard Woodruff <r-woodruff2 at ti.com>
+ * Syed Mohammed Khasim <khasim at ti.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-types.h>
+#include "zoom2.h"
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gpmc_init (); /* in SRAM or SDRAM, finish GPMC */
+ /* board id for Linux */
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP_ZOOM2;
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ return 0;
+}
+
+/*
+ * Routine: misc_init_r
+ * Description: Configure zoom board specific configurations
+ */
+int misc_init_r (void)
+{
+ power_init_r ();
+ dieid_num_r ();
+ return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * hardware. Many pins need to be moved from protect to primary
+ * mode.
+ */
+void set_muxconf_regs (void)
+{
+ /* platform specific muxes */
+ MUX_ZOOM2 ();
+}
diff --git a/board/omap3/zoom2/zoom2.h b/board/omap3/zoom2/zoom2.h
new file mode 100644
index 0000000..cae8a7a
--- /dev/null
+++ b/board/omap3/zoom2/zoom2.h
@@ -0,0 +1,149 @@
+/*
+ * Copyright (c) 2009 Wind River Systems, Inc.
+ * Tom Rix <Tom.Rix at windriver.com>
+ *
+ * Derived from: board/omap3/zoom1/zoom1.h
+ * Nishanth Menon <nm at ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _BOARD_ZOOM2_H_
+#define _BOARD_ZOOM2_H_
+
+const omap3_sysinfo sysinfo = {
+ DDR_STACKED,
+ "OMAP3 Zoom2 ",
+ "NAND",
+};
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_ZOOM2() \
+ /* SDRC*/\
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /* SDRC_D0 */\
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /* SDRC_D1 */\
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /* SDRC_D2 */\
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /* SDRC_D3 */\
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /* SDRC_D4 */\
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /* SDRC_D5 */\
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /* SDRC_D6 */\
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /* SDRC_D7 */\
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /* SDRC_D8 */\
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /* SDRC_D9 */\
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /* SDRC_D10 */\
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /* SDRC_D11 */\
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /* SDRC_D12 */\
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /* SDRC_D13 */\
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /* SDRC_D14 */\
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /* SDRC_D15 */\
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /* SDRC_D16 */\
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /* SDRC_D17 */\
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /* SDRC_D18 */\
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /* SDRC_D19 */\
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /* SDRC_D20 */\
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /* SDRC_D21 */\
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /* SDRC_D22 */\
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /* SDRC_D23 */\
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /* SDRC_D24 */\
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /* SDRC_D25 */\
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /* SDRC_D26 */\
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /* SDRC_D27 */\
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /* SDRC_D28 */\
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /* SDRC_D29 */\
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /* SDRC_D30 */\
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /* SDRC_D31 */\
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /* SDRC_CLK */\
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /* SDRC_DQS0 */\
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /* SDRC_DQS1 */\
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /* SDRC_DQS2 */\
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /* SDRC_DQS3 */\
+/* GPMC */\
+ MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /* GPMC_A1 */\
+ MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /* GPMC_A2 */\
+ MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /* GPMC_A3 */\
+ MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /* GPMC_A4 */\
+ MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /* GPMC_A5 */\
+ MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /* GPMC_A6 */\
+ MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /* GPMC_A7 */\
+ MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /* GPMC_A8 */\
+ MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /* GPMC_A9 */\
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /* GPMC_A10 */\
+ MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /* GPMC_D0 */\
+ MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /* GPMC_D1 */\
+ MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /* GPMC_D2 */\
+ MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /* GPMC_D3 */\
+ MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /* GPMC_D4 */\
+ MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /* GPMC_D5 */\
+ MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /* GPMC_D6 */\
+ MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /* GPMC_D7 */\
+ MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /* GPMC_D8 */\
+ MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /* GPMC_D9 */\
+ MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /* GPMC_D10 */\
+ MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /* GPMC_D11 */\
+ MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /* GPMC_D12 */\
+ MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /* GPMC_D13 */\
+ MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /* GPMC_D14 */\
+ MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /* GPMC_D15 */\
+ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /* GPMC_nCS0 */\
+ MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M7)) /* GPMC_nCS1 */\
+ MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M7)) /* GPMC_nCS2 */\
+ MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M7)) /* GPMC_nCS3 */\
+ MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M7)) /* GPMC_nCS4 */\
+ MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M7)) /* GPMC_nCS5 */\
+ MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M7)) /* GPMC_nCS6 */\
+ MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M7)) /* GPMC_nCS7 */\
+ MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /* GPMC_CLK */\
+ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /* GPMC_nADV_ALE */\
+ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /* GPMC_nOE */\
+ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /* GPMC_nWE */\
+ MUX_VAL(CP(GPMC_NWP), (IDIS | PTU | DIS | M0)) /* GPMC_nWP */\
+ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0)) /* GPMC_nBE0_CLE */\
+ MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /* GPMC_nBE1 */\
+ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTD | EN | M0)) /* GPMC_WAIT0 */\
+ MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /* GPMC_WAIT1 */\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /* GPMC_WAIT2 */\
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /* GPMC_WAIT3 */\
+/* IDCC modem Power On */\
+ MUX_VAL(CP(CAM_D11), (IEN | PTU | EN | M4)) /* GPIO_110 */\
+ MUX_VAL(CP(CAM_D4), (IEN | PTU | EN | M4)) /* GPIO_103 */\
+/* GPMC CS7 has LAN9211 device */\
+ MUX_VAL(CP(GPMC_NCS7), (IDIS | PTU | EN | M0)) /* GPMC_nCS7 */\
+ MUX_VAL(CP(MCBSP1_DX), (IEN | PTD | DIS | M4)) /* LAN9221 */\
+ MUX_VAL(CP(MCSPI1_CS2), (IEN | PTD | EN | M0)) /* MCSPI1_CS2 */\
+/* GPMC CS3 has Serial TL16CP754C device */\
+ MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /* GPMC_nCS3 */\
+/* Toggle Reset pin of TL16CP754C device */\
+ MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTU | EN | M4)) /* GPIO_152 */\
+ udelay(10);\
+ MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | EN | M4)) /* GPIO_152 */\
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTU | EN | M0)) /* SDRC_CKE1 */\
+/* LEDS */\
+ MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | EN | M4)) /* GPIO_173 red */\
+ MUX_VAL(CP(MCBSP4_DX), (IEN | PTD | EN | M4)) /* GPIO_154 blue */\
+ MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | EN | M4)) /* GPIO_61 blue2 */
+
+#endif /* _BOARD_ZOOM2_H_ */
diff --git a/doc/README.omap3 b/doc/README.omap3
index 1ba307f..9ab0979 100644
--- a/doc/README.omap3
+++ b/doc/README.omap3
@@ -19,6 +19,8 @@ Currently the following boards are supported:
* TI/Logic PD Zoom MDK [6]
+* TI/Logic PD Zoom 2 [7]
+
Toolchain
=========
@@ -54,6 +56,11 @@ make
make omap3_zoom1_config
make
+* Zoom 2:
+
+make omap3_zoom2_config
+make
+
Custom commands
===============
@@ -80,7 +87,7 @@ help
Acknowledgements
================
-OMAP3 U-Boot is based on U-Boot tar ball [7] for BeagleBoard and EVM done by
+OMAP3 U-Boot is based on U-Boot tar ball [8] for BeagleBoard and EVM done by
several TI employees.
Links
@@ -111,6 +118,10 @@ http://openpandora.org/
http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit
-[7] TI OMAP3 U-Boot:
+[7] TI/Logic PD Zoom 2
+
+http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
+[8] TI OMAP3 U-Boot:
http://beagleboard.googlecode.com/files/u-boot_beagle_revb.tar.gz
+
diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h
new file mode 100644
index 0000000..8aea4cb
--- /dev/null
+++ b/include/configs/omap3_zoom2.h
@@ -0,0 +1,226 @@
+/*
+ * (C) Copyright 2006-2009
+ * Texas Instruments.
+ * Richard Woodruff <r-woodruff2 at ti.com>
+ * Syed Mohammed Khasim <x0khasim at ti.com>
+ * Nishanth Menon <nm at ti.com>
+ * Tom Rix <Tom.Rix at windriver.com>
+ *
+ * Configuration settings for the TI OMAP3430 Zoom II board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
+#define CONFIG_OMAP 1 /* in a TI OMAP core */
+#define CONFIG_OMAP34XX 1 /* which is a 34XX */
+#define CONFIG_OMAP3430 1 /* which is in a 3430 */
+#define CONFIG_OMAP3_ZOOM2 1 /* working with Zoom II */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ /* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+#define CONFIG_REVISION_TAG 1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+ /* Sector */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
+ /* initial data */
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
+#define CONFIG_SERIAL3 3 /* UART3 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
+ 115200}
+#define CONFIG_MMC 1
+#define CONFIG_OMAP3_MMC 1
+#define CONFIG_DOS_PARTITION 1
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_NAND_LOCK_UNLOCK /* Enable lock/unlock support */
+
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMI /* iminfo */
+#undef CONFIG_CMD_IMLS /* List all found images */
+#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
+#undef CONFIG_CMD_NFS /* NFS support */
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_BUS 0
+#define CONFIG_SYS_I2C_BUS_SELECT 1
+#define CONFIG_DRIVER_OMAP34XX_I2C 1
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
+ /* to access nand */
+#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
+ /* to access nand at */
+ /* CS0 */
+#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+
+/* Environment information */
+#define CONFIG_BOOTDELAY 10
+
+/*
+ * Miscellaneous configurable options
+ */
+
+#define CONFIG_SYS_PROMPT "OMAP3 Zoom2 # "
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+/* Memtest from start of memory to 31MB */
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + 0x01F00000)
+/* The default load address is the start of memory */
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)
+/* everything, incl board info, in Hz */
+#undef CONFIG_SYS_CLKS_IN_HZ
+/*
+ * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
+ * 32KHz clk, or from external sig. This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV))
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using these settings
+ */
+#define CONFIG_STACKSIZE SZ_128K
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ SZ_4K
+#define CONFIG_STACKSIZE_FIQ SZ_4K
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C 1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
+
+#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
+ /* one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+
+#define CONFIG_SYS_FLASH_BASE boot_flash_base
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_ENV_IS_IN_NAND 1
+#define SMNAND_ENV_OFFSET 0x0c0000 /* environment starts here */
+
+#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
+#define CONFIG_ENV_OFFSET boot_flash_off
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
+
+#ifndef __ASSEMBLY__
+extern gpmc_csx_t *nand_cs_base;
+extern gpmc_t *gpmc_cfg_base;
+extern unsigned int boot_flash_base;
+extern volatile unsigned int boot_flash_env_addr;
+extern unsigned int boot_flash_off;
+extern unsigned int boot_flash_sec;
+extern unsigned int boot_flash_type;
+#endif
+
+#endif /* __CONFIG_H */
--
1.6.0.5
More information about the U-Boot
mailing list