[U-Boot] [PATCH] mtd: Add MTD concat support to concatenate multiple MTD NOR devices
Stefan Roese
sr at denx.de
Mon May 11 16:07:45 CEST 2009
This patch adds concatenation support to the U-Boot MTD infrastructure.
By enabling CONFIG_MTD_CONCAT this MTD CFI wrapper will concatenate
all found NOR devices into one single MTD device. This can be used by
e.g by UBI to access a partition that spans over multiple NOR chips.
Signed-off-by: Stefan Roese <sr at denx.de>
---
drivers/mtd/Makefile | 1 +
drivers/mtd/cfi_mtd.c | 77 +++++-
drivers/mtd/mtdconcat.c | 807 ++++++++++++++++++++++++++++++++++++++++++++
include/linux/mtd/compat.h | 12 +-
include/linux/mtd/concat.h | 21 ++
5 files changed, 913 insertions(+), 5 deletions(-)
create mode 100644 drivers/mtd/mtdconcat.c
create mode 100644 include/linux/mtd/concat.h
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index ed3f91e..19dc02b 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -26,6 +26,7 @@ include $(TOPDIR)/config.mk
LIB := $(obj)libmtd.a
COBJS-$(CONFIG_MTD_PARTITIONS) += mtdcore.o mtdpart.o
+COBJS-$(CONFIG_MTD_CONCAT) += mtdconcat.o
COBJS-$(CONFIG_HAS_DATAFLASH) += at45.o
COBJS-$(CONFIG_FLASH_CFI_DRIVER) += cfi_flash.o
COBJS-$(CONFIG_FLASH_CFI_MTD) += cfi_mtd.o
diff --git a/drivers/mtd/cfi_mtd.c b/drivers/mtd/cfi_mtd.c
index a0a15da..9a80e1d 100644
--- a/drivers/mtd/cfi_mtd.c
+++ b/drivers/mtd/cfi_mtd.c
@@ -25,14 +25,17 @@
#include <common.h>
#include <flash.h>
+#include <malloc.h>
#include <asm/errno.h>
#include <linux/mtd/mtd.h>
+#include <linux/mtd/concat.h>
extern flash_info_t flash_info[];
static struct mtd_info cfi_mtd_info[CONFIG_SYS_MAX_FLASH_BANKS];
static char cfi_mtd_names[CONFIG_SYS_MAX_FLASH_BANKS][16];
+static __attribute__((unused)) char c_mtd_name[16];
static int cfi_mtd_erase(struct mtd_info *mtd, struct erase_info *instr)
{
@@ -145,16 +148,68 @@ static int cfi_mtd_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
static int cfi_mtd_set_erasesize(struct mtd_info *mtd, flash_info_t *fi)
{
int sect_size = 0;
+ int sect_size_old = 0;
int sect;
+ int regions = 0;
+ int numblocks = 0;
+ ulong offset = 0;
+ ulong base_addr = fi->start[0];
/*
- * Select the largest sector size as erasesize (e.g. for UBI)
+ * First detect the number of eraseregions so that we can allocate
+ * the array of eraseregions correctly
*/
for (sect = 0; sect < fi->sector_count; sect++) {
+ if (sect_size_old != flash_sector_size(fi, sect))
+ regions++;
+ sect_size_old = flash_sector_size(fi, sect);
+ }
+
+ mtd->eraseregions = malloc(sizeof(struct mtd_erase_region_info) * regions);
+
+ /*
+ * Now detect the largest sector and fill the eraseregions
+ */
+ sect_size_old = 0;
+ regions = 0;
+ for (sect = 0; sect < fi->sector_count; sect++) {
+ if ((sect_size_old != flash_sector_size(fi, sect)) &&
+ (sect_size_old != 0)) {
+ mtd->eraseregions[regions].offset = offset - base_addr;
+ mtd->eraseregions[regions].erasesize = sect_size_old;
+ mtd->eraseregions[regions].numblocks = numblocks;
+
+ /* Now start counting the next eraseregions */
+ numblocks = 0;
+ regions++;
+ } else {
+ numblocks++;
+ }
+
+ if (sect_size_old != flash_sector_size(fi, sect))
+ offset = fi->start[sect];
+
+ /*
+ * Select the largest sector size as erasesize (e.g. for UBI)
+ */
if (flash_sector_size(fi, sect) > sect_size)
sect_size = flash_sector_size(fi, sect);
+
+ sect_size_old = flash_sector_size(fi, sect);
}
+ /*
+ * Set the last region
+ */
+ mtd->eraseregions[regions].offset = offset - base_addr;
+ mtd->eraseregions[regions].erasesize = sect_size_old;
+ mtd->eraseregions[regions].numblocks = numblocks + 1;
+
+ if (regions)
+ mtd->numeraseregions = regions + 1;
+ else
+ mtd->numeraseregions = 0;
+
mtd->erasesize = sect_size;
return 0;
@@ -165,6 +220,8 @@ int cfi_mtd_init(void)
struct mtd_info *mtd;
flash_info_t *fi;
int error, i;
+ int devices_found = 0;
+ struct mtd_info *mtd_list[CONFIG_SYS_MAX_FLASH_BANKS];
for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
fi = &flash_info[i];
@@ -193,7 +250,25 @@ int cfi_mtd_init(void)
if (add_mtd_device(mtd))
return -ENOMEM;
+
+ mtd_list[devices_found++] = mtd;
+ }
+
+#ifdef CONFIG_MTD_CONCAT
+ if (devices_found > 1) {
+ /*
+ * We detected multiple devices. Concatenate them together.
+ */
+ sprintf(c_mtd_name, "nor%d", devices_found);
+ mtd = mtd_concat_create(mtd_list, devices_found, c_mtd_name);
+
+ if (mtd == NULL)
+ return -ENXIO;
+
+ if (add_mtd_device(mtd))
+ return -ENOMEM;
}
+#endif /* CONFIG_MTD_CONCAT */
return 0;
}
diff --git a/drivers/mtd/mtdconcat.c b/drivers/mtd/mtdconcat.c
new file mode 100644
index 0000000..fc22701
--- /dev/null
+++ b/drivers/mtd/mtdconcat.c
@@ -0,0 +1,807 @@
+/*
+ * MTD device concatenation layer
+ *
+ * (C) 2002 Robert Kaiser <rkaiser at sysgo.de>
+ *
+ * NAND support by Christian Gan <cgan at iders.ca>
+ *
+ * This code is GPL
+ */
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/compat.h>
+#include <linux/mtd/concat.h>
+#include <ubi_uboot.h>
+
+/*
+ * Our storage structure:
+ * Subdev points to an array of pointers to struct mtd_info objects
+ * which is allocated along with this structure
+ *
+ */
+struct mtd_concat {
+ struct mtd_info mtd;
+ int num_subdev;
+ struct mtd_info **subdev;
+};
+
+/*
+ * how to calculate the size required for the above structure,
+ * including the pointer array subdev points to:
+ */
+#define SIZEOF_STRUCT_MTD_CONCAT(num_subdev) \
+ ((sizeof(struct mtd_concat) + (num_subdev) * sizeof(struct mtd_info *)))
+
+/*
+ * Given a pointer to the MTD object in the mtd_concat structure,
+ * we can retrieve the pointer to that structure with this macro.
+ */
+#define CONCAT(x) ((struct mtd_concat *)(x))
+
+/*
+ * MTD methods which look up the relevant subdevice, translate the
+ * effective address and pass through to the subdevice.
+ */
+
+static int
+concat_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t * retlen, u_char * buf)
+{
+ struct mtd_concat *concat = CONCAT(mtd);
+ int ret = 0, err;
+ int i;
+
+ *retlen = 0;
+
+ for (i = 0; i < concat->num_subdev; i++) {
+ struct mtd_info *subdev = concat->subdev[i];
+ size_t size, retsize;
+
+ if (from >= subdev->size) {
+ /* Not destined for this subdev */
+ size = 0;
+ from -= subdev->size;
+ continue;
+ }
+ if (from + len > subdev->size)
+ /* First part goes into this subdev */
+ size = subdev->size - from;
+ else
+ /* Entire transaction goes into this subdev */
+ size = len;
+
+ err = subdev->read(subdev, from, size, &retsize, buf);
+
+ /* Save information about bitflips! */
+ if (unlikely(err)) {
+ if (err == -EBADMSG) {
+ mtd->ecc_stats.failed++;
+ ret = err;
+ } else if (err == -EUCLEAN) {
+ mtd->ecc_stats.corrected++;
+ /* Do not overwrite -EBADMSG !! */
+ if (!ret)
+ ret = err;
+ } else
+ return err;
+ }
+
+ *retlen += retsize;
+ len -= size;
+ if (len == 0)
+ return ret;
+
+ buf += size;
+ from = 0;
+ }
+ return -EINVAL;
+}
+
+static int
+concat_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t * retlen, const u_char * buf)
+{
+ struct mtd_concat *concat = CONCAT(mtd);
+ int err = -EINVAL;
+ int i;
+
+ if (!(mtd->flags & MTD_WRITEABLE))
+ return -EROFS;
+
+ *retlen = 0;
+
+ for (i = 0; i < concat->num_subdev; i++) {
+ struct mtd_info *subdev = concat->subdev[i];
+ size_t size, retsize;
+
+ if (to >= subdev->size) {
+ size = 0;
+ to -= subdev->size;
+ continue;
+ }
+ if (to + len > subdev->size)
+ size = subdev->size - to;
+ else
+ size = len;
+
+ if (!(subdev->flags & MTD_WRITEABLE))
+ err = -EROFS;
+ else
+ err = subdev->write(subdev, to, size, &retsize, buf);
+
+ if (err)
+ break;
+
+ *retlen += retsize;
+ len -= size;
+ if (len == 0)
+ break;
+
+ err = -EINVAL;
+ buf += size;
+ to = 0;
+ }
+ return err;
+}
+
+static int
+concat_read_oob(struct mtd_info *mtd, loff_t from, struct mtd_oob_ops *ops)
+{
+ struct mtd_concat *concat = CONCAT(mtd);
+ struct mtd_oob_ops devops = *ops;
+ int i, err, ret = 0;
+
+ ops->retlen = ops->oobretlen = 0;
+
+ for (i = 0; i < concat->num_subdev; i++) {
+ struct mtd_info *subdev = concat->subdev[i];
+
+ if (from >= subdev->size) {
+ from -= subdev->size;
+ continue;
+ }
+
+ /* partial read ? */
+ if (from + devops.len > subdev->size)
+ devops.len = subdev->size - from;
+
+ err = subdev->read_oob(subdev, from, &devops);
+ ops->retlen += devops.retlen;
+ ops->oobretlen += devops.oobretlen;
+
+ /* Save information about bitflips! */
+ if (unlikely(err)) {
+ if (err == -EBADMSG) {
+ mtd->ecc_stats.failed++;
+ ret = err;
+ } else if (err == -EUCLEAN) {
+ mtd->ecc_stats.corrected++;
+ /* Do not overwrite -EBADMSG !! */
+ if (!ret)
+ ret = err;
+ } else
+ return err;
+ }
+
+ if (devops.datbuf) {
+ devops.len = ops->len - ops->retlen;
+ if (!devops.len)
+ return ret;
+ devops.datbuf += devops.retlen;
+ }
+ if (devops.oobbuf) {
+ devops.ooblen = ops->ooblen - ops->oobretlen;
+ if (!devops.ooblen)
+ return ret;
+ devops.oobbuf += ops->oobretlen;
+ }
+
+ from = 0;
+ }
+ return -EINVAL;
+}
+
+static int
+concat_write_oob(struct mtd_info *mtd, loff_t to, struct mtd_oob_ops *ops)
+{
+ struct mtd_concat *concat = CONCAT(mtd);
+ struct mtd_oob_ops devops = *ops;
+ int i, err;
+
+ if (!(mtd->flags & MTD_WRITEABLE))
+ return -EROFS;
+
+ ops->retlen = 0;
+
+ for (i = 0; i < concat->num_subdev; i++) {
+ struct mtd_info *subdev = concat->subdev[i];
+
+ if (to >= subdev->size) {
+ to -= subdev->size;
+ continue;
+ }
+
+ /* partial write ? */
+ if (to + devops.len > subdev->size)
+ devops.len = subdev->size - to;
+
+ err = subdev->write_oob(subdev, to, &devops);
+ ops->retlen += devops.retlen;
+ if (err)
+ return err;
+
+ if (devops.datbuf) {
+ devops.len = ops->len - ops->retlen;
+ if (!devops.len)
+ return 0;
+ devops.datbuf += devops.retlen;
+ }
+ if (devops.oobbuf) {
+ devops.ooblen = ops->ooblen - ops->oobretlen;
+ if (!devops.ooblen)
+ return 0;
+ devops.oobbuf += devops.oobretlen;
+ }
+ to = 0;
+ }
+ return -EINVAL;
+}
+
+static void concat_erase_callback(struct erase_info *instr)
+{
+ /* Nothing to do here in U-Boot */
+}
+
+static int concat_dev_erase(struct mtd_info *mtd, struct erase_info *erase)
+{
+ int err;
+ wait_queue_head_t waitq;
+ DECLARE_WAITQUEUE(wait, current);
+
+ /*
+ * This code was stol^H^H^H^Hinspired by mtdchar.c
+ */
+ init_waitqueue_head(&waitq);
+
+ erase->mtd = mtd;
+ erase->callback = concat_erase_callback;
+ erase->priv = (unsigned long) &waitq;
+
+ /*
+ * FIXME: Allow INTERRUPTIBLE. Which means
+ * not having the wait_queue head on the stack.
+ */
+ err = mtd->erase(mtd, erase);
+ if (!err) {
+ set_current_state(TASK_UNINTERRUPTIBLE);
+ add_wait_queue(&waitq, &wait);
+ if (erase->state != MTD_ERASE_DONE
+ && erase->state != MTD_ERASE_FAILED)
+ schedule();
+ remove_wait_queue(&waitq, &wait);
+ set_current_state(TASK_RUNNING);
+
+ err = (erase->state == MTD_ERASE_FAILED) ? -EIO : 0;
+ }
+ return err;
+}
+
+static int concat_erase(struct mtd_info *mtd, struct erase_info *instr)
+{
+ struct mtd_concat *concat = CONCAT(mtd);
+ struct mtd_info *subdev;
+ int i, err;
+ uint64_t length, offset = 0;
+ struct erase_info *erase;
+
+ if (!(mtd->flags & MTD_WRITEABLE))
+ return -EROFS;
+
+ if (instr->addr > concat->mtd.size)
+ return -EINVAL;
+
+ if (instr->len + instr->addr > concat->mtd.size)
+ return -EINVAL;
+
+ /*
+ * Check for proper erase block alignment of the to-be-erased area.
+ * It is easier to do this based on the super device's erase
+ * region info rather than looking at each particular sub-device
+ * in turn.
+ */
+ if (!concat->mtd.numeraseregions) {
+ /* the easy case: device has uniform erase block size */
+ if (instr->addr & (concat->mtd.erasesize - 1))
+ return -EINVAL;
+ if (instr->len & (concat->mtd.erasesize - 1))
+ return -EINVAL;
+ } else {
+ /* device has variable erase size */
+ struct mtd_erase_region_info *erase_regions =
+ concat->mtd.eraseregions;
+
+ /*
+ * Find the erase region where the to-be-erased area begins:
+ */
+ for (i = 0; i < concat->mtd.numeraseregions &&
+ instr->addr >= erase_regions[i].offset; i++) ;
+ --i;
+
+ /*
+ * Now erase_regions[i] is the region in which the
+ * to-be-erased area begins. Verify that the starting
+ * offset is aligned to this region's erase size:
+ */
+ if (instr->addr & (erase_regions[i].erasesize - 1))
+ return -EINVAL;
+
+ /*
+ * now find the erase region where the to-be-erased area ends:
+ */
+ for (; i < concat->mtd.numeraseregions &&
+ (instr->addr + instr->len) >= erase_regions[i].offset;
+ ++i) ;
+ --i;
+ /*
+ * check if the ending offset is aligned to this region's erase size
+ */
+ if ((instr->addr + instr->len) & (erase_regions[i].erasesize -
+ 1))
+ return -EINVAL;
+ }
+
+ instr->fail_addr = MTD_FAIL_ADDR_UNKNOWN;
+
+ /* make a local copy of instr to avoid modifying the caller's struct */
+ erase = kmalloc(sizeof (struct erase_info), GFP_KERNEL);
+
+ if (!erase)
+ return -ENOMEM;
+
+ *erase = *instr;
+ length = instr->len;
+
+ /*
+ * find the subdevice where the to-be-erased area begins, adjust
+ * starting offset to be relative to the subdevice start
+ */
+ for (i = 0; i < concat->num_subdev; i++) {
+ subdev = concat->subdev[i];
+ if (subdev->size <= erase->addr) {
+ erase->addr -= subdev->size;
+ offset += subdev->size;
+ } else {
+ break;
+ }
+ }
+
+ /* must never happen since size limit has been verified above */
+ BUG_ON(i >= concat->num_subdev);
+
+ /* now do the erase: */
+ err = 0;
+ for (; length > 0; i++) {
+ /* loop for all subdevices affected by this request */
+ subdev = concat->subdev[i]; /* get current subdevice */
+
+ /* limit length to subdevice's size: */
+ if (erase->addr + length > subdev->size)
+ erase->len = subdev->size - erase->addr;
+ else
+ erase->len = length;
+
+ if (!(subdev->flags & MTD_WRITEABLE)) {
+ err = -EROFS;
+ break;
+ }
+ length -= erase->len;
+ if ((err = concat_dev_erase(subdev, erase))) {
+ /* sanity check: should never happen since
+ * block alignment has been checked above */
+ BUG_ON(err == -EINVAL);
+ if (erase->fail_addr != MTD_FAIL_ADDR_UNKNOWN)
+ instr->fail_addr = erase->fail_addr + offset;
+ break;
+ }
+ /*
+ * erase->addr specifies the offset of the area to be
+ * erased *within the current subdevice*. It can be
+ * non-zero only the first time through this loop, i.e.
+ * for the first subdevice where blocks need to be erased.
+ * All the following erases must begin at the start of the
+ * current subdevice, i.e. at offset zero.
+ */
+ erase->addr = 0;
+ offset += subdev->size;
+ }
+ instr->state = erase->state;
+ kfree(erase);
+ if (err)
+ return err;
+
+ if (instr->callback)
+ instr->callback(instr);
+ return 0;
+}
+
+static int concat_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
+{
+ struct mtd_concat *concat = CONCAT(mtd);
+ int i, err = -EINVAL;
+
+ if ((len + ofs) > mtd->size)
+ return -EINVAL;
+
+ for (i = 0; i < concat->num_subdev; i++) {
+ struct mtd_info *subdev = concat->subdev[i];
+ uint64_t size;
+
+ if (ofs >= subdev->size) {
+ size = 0;
+ ofs -= subdev->size;
+ continue;
+ }
+ if (ofs + len > subdev->size)
+ size = subdev->size - ofs;
+ else
+ size = len;
+
+ err = subdev->lock(subdev, ofs, size);
+
+ if (err)
+ break;
+
+ len -= size;
+ if (len == 0)
+ break;
+
+ err = -EINVAL;
+ ofs = 0;
+ }
+
+ return err;
+}
+
+static int concat_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
+{
+ struct mtd_concat *concat = CONCAT(mtd);
+ int i, err = 0;
+
+ if ((len + ofs) > mtd->size)
+ return -EINVAL;
+
+ for (i = 0; i < concat->num_subdev; i++) {
+ struct mtd_info *subdev = concat->subdev[i];
+ uint64_t size;
+
+ if (ofs >= subdev->size) {
+ size = 0;
+ ofs -= subdev->size;
+ continue;
+ }
+ if (ofs + len > subdev->size)
+ size = subdev->size - ofs;
+ else
+ size = len;
+
+ err = subdev->unlock(subdev, ofs, size);
+
+ if (err)
+ break;
+
+ len -= size;
+ if (len == 0)
+ break;
+
+ err = -EINVAL;
+ ofs = 0;
+ }
+
+ return err;
+}
+
+static void concat_sync(struct mtd_info *mtd)
+{
+ struct mtd_concat *concat = CONCAT(mtd);
+ int i;
+
+ for (i = 0; i < concat->num_subdev; i++) {
+ struct mtd_info *subdev = concat->subdev[i];
+ subdev->sync(subdev);
+ }
+}
+
+static int concat_block_isbad(struct mtd_info *mtd, loff_t ofs)
+{
+ struct mtd_concat *concat = CONCAT(mtd);
+ int i, res = 0;
+
+ if (!concat->subdev[0]->block_isbad)
+ return res;
+
+ if (ofs > mtd->size)
+ return -EINVAL;
+
+ for (i = 0; i < concat->num_subdev; i++) {
+ struct mtd_info *subdev = concat->subdev[i];
+
+ if (ofs >= subdev->size) {
+ ofs -= subdev->size;
+ continue;
+ }
+
+ res = subdev->block_isbad(subdev, ofs);
+ break;
+ }
+
+ return res;
+}
+
+static int concat_block_markbad(struct mtd_info *mtd, loff_t ofs)
+{
+ struct mtd_concat *concat = CONCAT(mtd);
+ int i, err = -EINVAL;
+
+ if (!concat->subdev[0]->block_markbad)
+ return 0;
+
+ if (ofs > mtd->size)
+ return -EINVAL;
+
+ for (i = 0; i < concat->num_subdev; i++) {
+ struct mtd_info *subdev = concat->subdev[i];
+
+ if (ofs >= subdev->size) {
+ ofs -= subdev->size;
+ continue;
+ }
+
+ err = subdev->block_markbad(subdev, ofs);
+ if (!err)
+ mtd->ecc_stats.badblocks++;
+ break;
+ }
+
+ return err;
+}
+
+/*
+ * This function constructs a virtual MTD device by concatenating
+ * num_devs MTD devices. A pointer to the new device object is
+ * stored to *new_dev upon success. This function does _not_
+ * register any devices: this is the caller's responsibility.
+ */
+struct mtd_info *mtd_concat_create(struct mtd_info *subdev[], /* subdevices to concatenate */
+ int num_devs, /* number of subdevices */
+ const char *name)
+{ /* name for the new device */
+ int i;
+ size_t size;
+ struct mtd_concat *concat;
+ uint32_t max_erasesize, curr_erasesize;
+ int num_erase_region;
+
+ debug("Concatenating MTD devices:\n");
+ for (i = 0; i < num_devs; i++)
+ debug("(%d): \"%s\"\n", i, subdev[i]->name);
+ debug("into device \"%s\"\n", name);
+
+ /* allocate the device structure */
+ size = SIZEOF_STRUCT_MTD_CONCAT(num_devs);
+ concat = kzalloc(size, GFP_KERNEL);
+ if (!concat) {
+ printk
+ ("memory allocation error while creating concatenated device \"%s\"\n",
+ name);
+ return NULL;
+ }
+ concat->subdev = (struct mtd_info **) (concat + 1);
+
+ /*
+ * Set up the new "super" device's MTD object structure, check for
+ * incompatibilites between the subdevices.
+ */
+ concat->mtd.type = subdev[0]->type;
+ concat->mtd.flags = subdev[0]->flags;
+ concat->mtd.size = subdev[0]->size;
+ concat->mtd.erasesize = subdev[0]->erasesize;
+ concat->mtd.writesize = subdev[0]->writesize;
+ concat->mtd.subpage_sft = subdev[0]->subpage_sft;
+ concat->mtd.oobsize = subdev[0]->oobsize;
+ concat->mtd.oobavail = subdev[0]->oobavail;
+ if (subdev[0]->read_oob)
+ concat->mtd.read_oob = concat_read_oob;
+ if (subdev[0]->write_oob)
+ concat->mtd.write_oob = concat_write_oob;
+ if (subdev[0]->block_isbad)
+ concat->mtd.block_isbad = concat_block_isbad;
+ if (subdev[0]->block_markbad)
+ concat->mtd.block_markbad = concat_block_markbad;
+
+ concat->mtd.ecc_stats.badblocks = subdev[0]->ecc_stats.badblocks;
+
+ concat->subdev[0] = subdev[0];
+
+ for (i = 1; i < num_devs; i++) {
+ if (concat->mtd.type != subdev[i]->type) {
+ kfree(concat);
+ printk("Incompatible device type on \"%s\"\n",
+ subdev[i]->name);
+ return NULL;
+ }
+ if (concat->mtd.flags != subdev[i]->flags) {
+ /*
+ * Expect all flags except MTD_WRITEABLE to be
+ * equal on all subdevices.
+ */
+ if ((concat->mtd.flags ^ subdev[i]->
+ flags) & ~MTD_WRITEABLE) {
+ kfree(concat);
+ printk("Incompatible device flags on \"%s\"\n",
+ subdev[i]->name);
+ return NULL;
+ } else
+ /* if writeable attribute differs,
+ make super device writeable */
+ concat->mtd.flags |=
+ subdev[i]->flags & MTD_WRITEABLE;
+ }
+
+ concat->mtd.size += subdev[i]->size;
+ concat->mtd.ecc_stats.badblocks +=
+ subdev[i]->ecc_stats.badblocks;
+ if (concat->mtd.writesize != subdev[i]->writesize ||
+ concat->mtd.subpage_sft != subdev[i]->subpage_sft ||
+ concat->mtd.oobsize != subdev[i]->oobsize ||
+ !concat->mtd.read_oob != !subdev[i]->read_oob ||
+ !concat->mtd.write_oob != !subdev[i]->write_oob) {
+ kfree(concat);
+ printk("Incompatible OOB or ECC data on \"%s\"\n",
+ subdev[i]->name);
+ return NULL;
+ }
+ concat->subdev[i] = subdev[i];
+
+ }
+
+ concat->mtd.ecclayout = subdev[0]->ecclayout;
+
+ concat->num_subdev = num_devs;
+ concat->mtd.name = name;
+
+ concat->mtd.erase = concat_erase;
+ concat->mtd.read = concat_read;
+ concat->mtd.write = concat_write;
+ concat->mtd.sync = concat_sync;
+ concat->mtd.lock = concat_lock;
+ concat->mtd.unlock = concat_unlock;
+
+ /*
+ * Combine the erase block size info of the subdevices:
+ *
+ * first, walk the map of the new device and see how
+ * many changes in erase size we have
+ */
+ max_erasesize = curr_erasesize = subdev[0]->erasesize;
+ num_erase_region = 1;
+ for (i = 0; i < num_devs; i++) {
+ if (subdev[i]->numeraseregions == 0) {
+ /* current subdevice has uniform erase size */
+ if (subdev[i]->erasesize != curr_erasesize) {
+ /* if it differs from the last subdevice's erase size, count it */
+ ++num_erase_region;
+ curr_erasesize = subdev[i]->erasesize;
+ if (curr_erasesize > max_erasesize)
+ max_erasesize = curr_erasesize;
+ }
+ } else {
+ /* current subdevice has variable erase size */
+ int j;
+ for (j = 0; j < subdev[i]->numeraseregions; j++) {
+
+ /* walk the list of erase regions, count any changes */
+ if (subdev[i]->eraseregions[j].erasesize !=
+ curr_erasesize) {
+ ++num_erase_region;
+ curr_erasesize =
+ subdev[i]->eraseregions[j].
+ erasesize;
+ if (curr_erasesize > max_erasesize)
+ max_erasesize = curr_erasesize;
+ }
+ }
+ }
+ }
+
+ if (num_erase_region == 1) {
+ /*
+ * All subdevices have the same uniform erase size.
+ * This is easy:
+ */
+ concat->mtd.erasesize = curr_erasesize;
+ concat->mtd.numeraseregions = 0;
+ } else {
+ uint64_t tmp64;
+
+ /*
+ * erase block size varies across the subdevices: allocate
+ * space to store the data describing the variable erase regions
+ */
+ struct mtd_erase_region_info *erase_region_p;
+ uint64_t begin, position;
+
+ concat->mtd.erasesize = max_erasesize;
+ concat->mtd.numeraseregions = num_erase_region;
+ concat->mtd.eraseregions = erase_region_p =
+ kmalloc(num_erase_region *
+ sizeof (struct mtd_erase_region_info), GFP_KERNEL);
+ if (!erase_region_p) {
+ kfree(concat);
+ printk
+ ("memory allocation error while creating erase region list"
+ " for device \"%s\"\n", name);
+ return NULL;
+ }
+
+ /*
+ * walk the map of the new device once more and fill in
+ * in erase region info:
+ */
+ curr_erasesize = subdev[0]->erasesize;
+ begin = position = 0;
+ for (i = 0; i < num_devs; i++) {
+ if (subdev[i]->numeraseregions == 0) {
+ /* current subdevice has uniform erase size */
+ if (subdev[i]->erasesize != curr_erasesize) {
+ /*
+ * fill in an mtd_erase_region_info structure for the area
+ * we have walked so far:
+ */
+ erase_region_p->offset = begin;
+ erase_region_p->erasesize =
+ curr_erasesize;
+ tmp64 = position - begin;
+ do_div(tmp64, curr_erasesize);
+ erase_region_p->numblocks = tmp64;
+ begin = position;
+
+ curr_erasesize = subdev[i]->erasesize;
+ ++erase_region_p;
+ }
+ position += subdev[i]->size;
+ } else {
+ /* current subdevice has variable erase size */
+ int j;
+ for (j = 0; j < subdev[i]->numeraseregions; j++) {
+ /* walk the list of erase regions, count any changes */
+ if (subdev[i]->eraseregions[j].
+ erasesize != curr_erasesize) {
+ erase_region_p->offset = begin;
+ erase_region_p->erasesize =
+ curr_erasesize;
+ tmp64 = position - begin;
+ do_div(tmp64, curr_erasesize);
+ erase_region_p->numblocks = tmp64;
+ begin = position;
+
+ curr_erasesize =
+ subdev[i]->eraseregions[j].
+ erasesize;
+ ++erase_region_p;
+ }
+ position +=
+ subdev[i]->eraseregions[j].
+ numblocks * (uint64_t)curr_erasesize;
+ }
+ }
+ }
+ /* Now write the final entry */
+ erase_region_p->offset = begin;
+ erase_region_p->erasesize = curr_erasesize;
+ tmp64 = position - begin;
+ do_div(tmp64, curr_erasesize);
+ erase_region_p->numblocks = tmp64;
+ }
+
+ return &concat->mtd;
+}
diff --git a/include/linux/mtd/compat.h b/include/linux/mtd/compat.h
index 9036b74..f0c8464 100644
--- a/include/linux/mtd/compat.h
+++ b/include/linux/mtd/compat.h
@@ -19,11 +19,15 @@
#define kmalloc(size, flags) malloc(size)
#define kzalloc(size, flags) calloc(size, 1)
-#define vmalloc(size) malloc(size)
-#define kfree(ptr) free(ptr)
-#define vfree(ptr) free(ptr)
+#define vmalloc(size) malloc(size)
+#define kfree(ptr) free(ptr)
+#define vfree(ptr) free(ptr)
-#define KERNEL_VERSION(a,b,c) (((a) << 16) + ((b) << 8) + (c))
+#define DECLARE_WAITQUEUE(...) do { } while (0)
+#define add_wait_queue(...) do { } while (0)
+#define remove_wait_queue(...) do { } while (0)
+
+#define KERNEL_VERSION(a,b,c) (((a) << 16) + ((b) << 8) + (c))
/*
* ..and if you can't take the strict
diff --git a/include/linux/mtd/concat.h b/include/linux/mtd/concat.h
new file mode 100644
index 0000000..e80c674
--- /dev/null
+++ b/include/linux/mtd/concat.h
@@ -0,0 +1,21 @@
+/*
+ * MTD device concatenation layer definitions
+ *
+ * (C) 2002 Robert Kaiser <rkaiser at sysgo.de>
+ *
+ * This code is GPL
+ */
+
+#ifndef MTD_CONCAT_H
+#define MTD_CONCAT_H
+
+
+struct mtd_info *mtd_concat_create(
+ struct mtd_info *subdev[], /* subdevices to concatenate */
+ int num_devs, /* number of subdevices */
+ const char *name); /* name for the new device */
+
+void mtd_concat_destroy(struct mtd_info *mtd);
+
+#endif
+
--
1.6.2.5
More information about the U-Boot
mailing list