[U-Boot] Please help for Data TLB Error in MPC8544
duckycool
duckycool at gmail.com
Thu May 21 15:45:02 CEST 2009
Hi all,
My board can't boot normally, and I found it just hang in data tlb error
through the system.map.
Could any one help for this?
Some regisers are as below:
============================================
DEAR: 0xf400fff0 (L1 init ram base address is 0xf4010000)
IVPR : 0xfff80000 , IVPR3: 0x000004000
EELADR: 0xf4010000 , CSn_BNDS: all 0x00000000 (I think SPD of DDR is not
found yet)
L2MMU_TLB0 : 84000000 51000000 ff7000000 ff7000000 (CCSR is not relocated to
0xe0000000 yet)
============================================
The TLB1 registers from CodeWarrior is as below:
=================================================
L2MMU_CAM0 600007CA 1C080000 FFC00000 FFC000001 (boot flash, 4M)
L2MMU_CAM1 A0007FCA 1C080000 80000000 800000001 (PCIE, 1G)
L2MMU_CAM2 90003FCA 1C080000 C0000000 C00000001 (PCI, 256M)
L2MMU_CAM3 90003FCA 1C080000 D0000000 D00000001 (PCI, 256M)
L2MMU_CAM4 80001FCA 1C080000 E0000000 E00000001 (CCSR, 64M)
L2MMU_CAM5 80001FCA 1C080000 F0000000 F00000001 (?? , 64M)
L2MMU_CAM6 300000CA 18080000 FF040000 FF0400001 (NAND, 64K)
L2MMU_CAM7 20000042 18080000 FF010000 FF0100001 (NAND, 16K)
L2MMU_CAM8 20000042 18080000 FF050000 FF0500001 (NAND, 16K)
L2MMU_CAM9 C87FD651 EB40000D 27DE6000 2397E000
L2MMU_CAM10 D0E2E2DF EB680009 B494F000 8F634000
L2MMU_CAM11 00FC8DCA 5A11000D BCB9B000 77EF6000
L2MMU_CAM12 300000CA 18080000 FF000000 FF000001 (NAND, 64K)
L2MMU_CAM13 D891AFD8 18180002 50A70000 F7AB6000
L2MMU_CAM14 E0F6AE97 DA390009 F5DF6000 4F425000
L2MMU_CAM15 D8EFEF88 C750000F AEBA7000 3229F000
===================================================
And this is my init.s below:
==================================================================
#include <ppc_asm.tmpl>
#include <ppc_defs.h>
#include <asm/cache.h>
#include <asm/mmu.h>
#include <config.h>
#include <mpc85xx.h>
#define LAWAR_TRGT_PCI1 0x00000000
#define LAWAR_TRGT_PCIE1 0x00200000
#define LAWAR_TRGT_PCIE2 0x00100000
#define LAWAR_TRGT_PCIE3 0x00300000
#define LAWAR_TRGT_LBC 0x00400000
#define LAWAR_TRGT_DDR 0x00f00000
#define entry_start \
mflr r1 ; \
bl 0f ;
#define entry_end \
0: mflr r0 ; \
mtlr r1 ; \
blr ;
.section .bootpg, "ax"
.globl tlb1_entry
tlb1_entry:
entry_start
/*
* Number of TLB0 and TLB1 entries in the following table
*/
.long (2f-1f)/16
1:
/*
* TLB0 4K Non-cacheable, guarded
* 0xff700000 4K Initial CCSRBAR mapping
*
* This ends up at a TLB0 Index==0 entry, and must not collide
* with other TLB0 Entries.
*/
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB0 16K Cacheable, guarded
* Temporary Global data for initialization
*
* Use four 4K TLB0 entries. These entries must be cacheable
* as they provide the bootstrap memory before the memory
* controler and real memory have been configured.
*
* These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
* and must not collide with other TLB0 entries.
*/
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),0,0,0,0,0,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),0,0,0,0,0,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 *
1024),0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),0,0,0,0,0,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 *
1024),0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 *
1024),0,0,0,0,0,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 *
1024),0,0,0,0,0,1,0,1,0,1)
/*
* TLB 0: 4M Non-cacheable, guarded
* 0xffc00000 4M Covers FLASH at 0xFFC00000
* Out of reset this entry is only 4K.
*/
.long TLB1_MAS0(1, 0, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_4M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_BOOT_BLOCK), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_BOOT_BLOCK), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 1: 1G Non-cacheable, guarded
* 0x80000000 1G PCIE 8,9,a,b
*/
.long TLB1_MAS0(1, 1, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G)
.long TLB1_MAS2(E500_TLB_EPN(CFG_PCIE_PHYS),0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_PCIE_PHYS),0,0,0,0,0,1,0,1,0,1)
/*
* TLB 2: 256M Non-cacheable, guarded
*/
.long TLB1_MAS0(1, 2, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS),0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS),0,0,0,0,0,1,0,1,0,1)
/*
* TLB 3: 256M Non-cacheable, guarded
*/
.long TLB1_MAS0(1, 3, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS + 0x10000000),0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS +
0x10000000),0,0,0,0,0,1,0,1,0,1)
/*
* TLB 4: 64M Non-cacheable, guarded
* 0xe000_0000 1M CCSRBAR
* 0xe100_0000 255M PCI IO range
*/
.long TLB1_MAS0(1, 4, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 5: 64M Non-cacheable, non-guarded , reserve from MPC8544DS (don't
know what is it for)
*/
.long TLB1_MAS0(1, 5, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
.long TLB1_MAS2(E500_TLB_EPN(0xf0000000), 0,0,0,0,0,0,0,0)
.long TLB1_MAS3(E500_TLB_RPN(0xf0000000), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 6: 64K Non-cacheable, guarded
* 0xff040000 64K 1G NAND flash 2 area 1 0xff040000
*/
.long TLB1_MAS0(1, 6, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64K)
.long TLB1_MAS2(E500_TLB_EPN(0xff040000), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(0xff040000), 0,0,0,0,0,0,0,1,0,1)
/*
* TLB 7: 16K Non-cacheable, guarded
* 0xff010000 16K 1G NAND flash 1 area 2 0xff010000
*/
.long TLB1_MAS0(1, 7, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16K)
.long TLB1_MAS2(E500_TLB_EPN(0xff010000), 0,0,0,0,0,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(0xff010000), 0,0,0,0,0,0,0,1,0,1)
/*
* TLB 8: 16K Non-cacheable, guarded
* 0xff050000 16K 1G NAND flash 2 area 2 0xff050000
*/
.long TLB1_MAS0(1, 8, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16K)
.long TLB1_MAS2(E500_TLB_EPN(0xff050000), 0,0,0,0,0,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(0xff050000), 0,0,0,0,0,0,0,1,0,1)
/*
* TLB 12: 64K Non-cacheable, guarded
* 0xff000000 64K 1G NAND flash 1 area 1 0xff000000
*/
.long TLB1_MAS0(1, 12, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64K)
.long TLB1_MAS2(E500_TLB_EPN(0xff000000), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(0xff000000), 0,0,0,0,0,0,0,1,0,1)
2:
entry_end
/*
* LAW(Local Access Window) configuration:
*/
.section .bootpg, "ax"
.globl law_entry
law_entry:
entry_start
.long (4f-3f)/8
3:
.long 0
.long LAWAR_EN | LAWAR_TRGT_DDR | (LAWAR_SIZE & LAWAR_SIZE_1G)
.long (CFG_PCI1_MEM_PHYS>>12) & 0xfffff
.long LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M)
.long (CFG_PCI1_IO_PHYS>>12) & 0xfffff
.long LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_64K)
.long (0xf0000000>>12) & 0xfffff
.long LAWAR_EN | LAWAR_TRGT_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M)
.long 0
.long 0
.long (CFG_PCIE1_IO_PHYS>>12) & 0xfffff
.long LAWAR_EN | LAWAR_TRGT_PCIE1 | (LAWAR_SIZE & LAWAR_SIZE_32G)
4:
entry_end
==============================================================================
What I think the problem might be
1. I didn't access the SPD to initial DDR , so failed ?
2. The TLB1_5 should take away ?
3. I shall add one more TLB for DDR ?
4. The real problem is not related with any above, and I shall post the
other regisers for check ??
Thanks.
--
View this message in context: http://www.nabble.com/Please-help-for-Data-TLB-Error-in-MPC8544-tp23653353p23653353.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
More information about the U-Boot
mailing list