[U-Boot] [PATCH V4 4/4] add TI DA8xx support: Integrate DA830 EVM support into U-Boot
Tom
Tom.Rix at windriver.com
Thu Nov 5 03:34:35 CET 2009
Nick Thompson wrote:
> From: Sekhar Nori <nsekhar at ti.com>
>
> Integrate DA830 EVM support into U-Boot.
>
> Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum
> Digital EVM board. See http://www.spectrumdigital.com/
>
> Signed-off-by: Nick Thompson <nick.thompson at gefanuc.com>
This looks fine.
Tom
> ---
> Applies to u-boot-ti
>
> MAINTAINERS | 4 +
> MAKEALL | 1 +
> Makefile | 3 +
> include/common.h | 3 +
> include/configs/da830evm.h | 243 ++++++++++++++++++++++++++++++++++++++++++++
> 5 files changed, 254 insertions(+), 0 deletions(-)
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index d70a9d2..5ca45a7 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -712,6 +712,10 @@ Andrea Scian <andrea.scian at dave-tech.it>
>
> B2 ARM7TDMI (S3C44B0X)
>
> +Nick Thompson <nick.thompson at gefanuc.com>
> +
> + da830evm ARM926EJS (DA830/OMAP-L137)
> +
> Albin Tonnerre <albin.tonnerre at free-electrons.com>
>
> sbc35_a9g20 ARM926EJS (AT91SAM9G20 SoC)
> diff --git a/MAKEALL b/MAKEALL
> index d63c5c2..a61e40c 100755
> --- a/MAKEALL
> +++ b/MAKEALL
> @@ -548,6 +548,7 @@ LIST_ARM9=" \
> cp926ejs \
> cp946es \
> cp966 \
> + da830evm \
> imx27lite \
> lpd7a400 \
> mv88f6281gtw_ge \
> diff --git a/Makefile b/Makefile
> index a69e6d5..bf6081b 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -2927,6 +2927,9 @@ cp922_XA10_config \
> cp1026_config: unconfig
> @board/armltd/integrator/split_by_variant.sh cp $@
>
> +da830evm_config: unconfig
> + @$(MKCONFIG) $(@:_config=) arm arm926ejs da830evm davinci davinci
> +
> davinci_dvevm_config : unconfig
> @$(MKCONFIG) $(@:_config=) arm arm926ejs dvevm davinci davinci
>
> diff --git a/include/common.h b/include/common.h
> index 7df9afa..7fb107c 100644
> --- a/include/common.h
> +++ b/include/common.h
> @@ -107,6 +107,9 @@ typedef volatile unsigned char vu_char;
> #ifdef CONFIG_BLACKFIN
> #include <asm/blackfin.h>
> #endif
> +#ifdef CONFIG_SOC_DA8XX
> +#include <asm/arch/hardware.h>
> +#endif
>
> #include <part.h>
> #include <flash.h>
> diff --git a/include/configs/da830evm.h b/include/configs/da830evm.h
> new file mode 100644
> index 0000000..38e2ce1
> --- /dev/null
> +++ b/include/configs/da830evm.h
> @@ -0,0 +1,243 @@
> +/*
> + * Copyright (C) 2008 Texas Instruments, Inc <www.ti.com>
> + *
> + * Based on davinci_dvevm.h. Original Copyrights follow:
> + *
> + * Copyright (C) 2007 Sergey Kubushyn <ksi at koi8.net>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +/*
> + * Board
> + */
> +
> +/*
> + * SoC Configuration
> + */
> +#define CONFIG_MACH_DAVINCI_DA830_EVM
> +#define CONFIG_ARM926EJS /* arm926ejs CPU core */
> +#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */
> +#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
> +#define CONFIG_SYS_OSCIN_FREQ 24000000
> +#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
> +#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
> +#define CONFIG_SYS_HZ 1000
> +#define CONFIG_SKIP_LOWLEVEL_INIT
> +#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
> +
> +/*
> + * Memory Info
> + */
> +#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */
> +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* reserved for initial data */
> +#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
> +#define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */
> +#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1 /* memtest start addr */
> +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024) /* 16MB test */
> +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
> +#define CONFIG_STACKSIZE (256*1024) /* regular stack */
> +
> +/*
> + * Serial Driver info
> + */
> +#define CONFIG_SYS_NS16550
> +#define CONFIG_SYS_NS16550_SERIAL
> +#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */
> +#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
> +#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
> +#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
> +#define CONFIG_BAUDRATE 115200 /* Default baud rate */
> +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
> +
> +/*
> + * I2C Configuration
> + */
> +#define CONFIG_HARD_I2C
> +#define CONFIG_DRIVER_DAVINCI_I2C
> +#define CONFIG_SYS_I2C_SPEED 25000 /* 100Kbps won't work, H/W bug */
> +#define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
> +
> +/*
> + * I2C EEPROM definitions for catalyst 24W256 EEPROM chip
> + */
> +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
> +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
> +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
> +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
> +
> +/*
> + * Network & Ethernet Configuration
> + */
> +#ifdef CONFIG_DRIVER_TI_EMAC
> +#define CONFIG_MII
> +#define CONFIG_BOOTP_DEFAULT
> +#define CONFIG_BOOTP_DNS
> +#define CONFIG_BOOTP_DNS2
> +#define CONFIG_BOOTP_SEND_HOSTNAME
> +#define CONFIG_NET_RETRY_COUNT 10
> +#define CONFIG_NET_MULTI
> +#endif
> +
> +/*
> + * Flash & Environment
> + */
> +#ifdef CONFIG_USE_NAND
> +#undef CONFIG_ENV_IS_IN_FLASH
> +#define CONFIG_NAND_DAVINCI
> +#define CONFIG_SYS_NO_FLASH
> +#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
> +#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
> +#define CONFIG_ENV_SIZE (128 << 10)
> +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
> +#define CONFIG_SYS_NAND_CS 3
> +#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
> +#define CONFIG_SYS_CLE_MASK 0x10
> +#define CONFIG_SYS_ALE_MASK 0x8
> +#define CONFIG_SYS_NAND_HW_ECC
> +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
> +#define NAND_MAX_CHIPS 1
> +#define DEF_BOOTM ""
> +#endif
> +
> +#ifdef CONFIG_USE_NOR
> +#define CONFIG_ENV_IS_IN_FLASH
> +#undef CONFIG_SYS_NO_FLASH
> +#define CONFIG_SYS_FLASH_CFI_DRIVER
> +#define CONFIG_SYS_FLASH_CFI
> +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
> +#define CONFIG_SYS_FLASH_SECT_SZ (64 << 10) /* 64KB */
> +#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*3)
> +#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
> +#define PHYS_FLASH_SIZE (32 << 20) /* Flash size 32MB */
> +#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
> +#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ
> +#define CONFIG_SYS_FLASH_SPL_ACCESS
> +#endif
> +
> +#ifdef CONFIG_USE_SPIFLASH
> +#undef CONFIG_ENV_IS_IN_FLASH
> +#undef CONFIG_ENV_IS_IN_NAND
> +#define CONFIG_ENV_IS_IN_SPI_FLASH
> +#define CONFIG_ENV_SIZE (16 << 10)
> +#define CONFIG_ENV_OFFSET (256 << 10)
> +#define CONFIG_ENV_SECT_SIZE 4096
> +#define CONFIG_SYS_NO_FLASH
> +#define CONFIG_SPI
> +#define CONFIG_SPI_FLASH
> +#define CONFIG_SPI_FLASH_WINBOND
> +#define CONFIG_DAVINCI_SPI
> +#define CONFIG_SYS_SPI_BASE DAVINCI_SPI0_BASE
> +#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI0_CLKID)
> +#define CONFIG_SF_DEFAULT_SPEED 50000000
> +#define CONFIG_SYS_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
> +#endif
> +
> +
> +/*
> + * U-Boot general configuration
> + */
> +#undef CONFIG_USE_IRQ /* No IRQ/FIQ in U-Boot */
> +#undef CONFIG_MISC_INIT_R
> +#undef CONFIG_BOOTDELAY
> +#define CONFIG_BOOTFILE "uImage" /* Boot file name */
> +#define CONFIG_SYS_PROMPT "DA830-evm > " /* Command Prompt */
> +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
> +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
> +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_MEMTEST_START + 0x700000)
> +#define CONFIG_VERSION_VARIABLE
> +#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */
> +#define CONFIG_SYS_HUSH_PARSER
> +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
> +#define CONFIG_CMDLINE_EDITING
> +#define CONFIG_SYS_LONGHELP
> +#define CONFIG_CRC32_VERIFY
> +#define CONFIG_MX_CYCLIC
> +
> +/*
> + * Linux Information
> + */
> +#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100)
> +#define CONFIG_CMDLINE_TAG
> +#define CONFIG_SETUP_MEMORY_TAGS
> +#define CONFIG_BOOTARGS "mem=32M console=ttyS2,115200n8 root=/dev/mtdblock/2 rw noinitrd ip=dhcp"
> +#define CONFIG_BOOTCOMMAND ""
> +#define CONFIG_BOOTDELAY 3
> +
> +/*
> + * U-Boot commands
> + */
> +#include <config_cmd_default.h>
> +#define CONFIG_CMD_ENV
> +#define CONFIG_CMD_ASKENV
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_DIAG
> +#define CONFIG_CMD_MII
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_SAVES
> +#define CONFIG_CMD_MEMORY
> +#undef CONFIG_CMD_FPGA
> +#undef CONFIG_CMD_SETGETDCR
> +#define CONFIG_CMD_EEPROM
> +
> +#ifndef CONFIG_DRIVER_TI_EMAC
> +#undef CONFIG_CMD_NET
> +#undef CONFIG_CMD_DHCP
> +#undef CONFIG_CMD_MII
> +#undef CONFIG_CMD_PING
> +#endif
> +
> +#ifdef CONFIG_USE_NAND
> +#undef CONFIG_CMD_FLASH
> +#undef CONFIG_CMD_IMLS
> +#define CONFIG_CMD_NAND
> +#define CONFIG_CMD_MTDPARTS
> +#define CONFIG_MTD_PARTITIONS
> +#define CONFIG_CMD_UBI
> +#define CONFIG_RBTREE
> +#endif
> +
> +#ifdef CONFIG_USE_SPIFLASH
> +#undef CONFIG_CMD_IMLS
> +#undef CONFIG_CMD_FLASH
> +#define CONFIG_CMD_SPI
> +#define CONFIG_CMD_SAVEENV
> +#endif
> +
> +#if !defined(CONFIG_USE_NAND) && \
> + !defined(CONFIG_USE_NOR) && \
> + !defined(CONFIG_USE_SPIFLASH)
> +#define CONFIG_ENV_IS_NOWHERE
> +#define CONFIG_SYS_NO_FLASH
> +#define CONFIG_ENV_SIZE (16 << 10)
> +#undef CONFIG_CMD_IMLS
> +#undef CONFIG_CMD_FLASH
> +#undef CONFIG_CMD_ENV
> +#endif
> +
> +#ifdef CONFIG_USB_DA8XX
> +#define CONFIG_CMD_USB /* include support for usb */
> +#define CONFIG_CMD_STORAGE /* include support for usb */
> +#define CONFIG_CMD_FAT /* include support for FAT/storage*/
> +#define CONFIG_DOS_PARTITION /* include support for FAT/storage*/
> +#endif
> +
> +#endif /* __CONFIG_H */
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
More information about the U-Boot
mailing list