[U-Boot] [PATCH V5 4/4] add TI DA8xx support: Integrate DA830 EVM support into U-Boot
Nick Thompson
nick.thompson at gefanuc.com
Tue Nov 10 16:09:56 CET 2009
From: Sekhar Nori <nsekhar at ti.com>
Integrate DA830 EVM support into U-Boot.
Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum
Digital EVM board. See http://www.spectrumdigital.com/
Signed-off-by: Nick Thompson <nick.thompson at gefanuc.com>
---
Applies to u-boot-ti
MAINTAINERS | 4 +
MAKEALL | 1 +
Makefile | 3 +
include/common.h | 3 +
include/configs/da830evm.h | 243 ++++++++++++++++++++++++++++++++++++++++++++
5 files changed, 254 insertions(+), 0 deletions(-)
diff --git a/MAINTAINERS b/MAINTAINERS
index d70a9d2..5ca45a7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -712,6 +712,10 @@ Andrea Scian <andrea.scian at dave-tech.it>
B2 ARM7TDMI (S3C44B0X)
+Nick Thompson <nick.thompson at gefanuc.com>
+
+ da830evm ARM926EJS (DA830/OMAP-L137)
+
Albin Tonnerre <albin.tonnerre at free-electrons.com>
sbc35_a9g20 ARM926EJS (AT91SAM9G20 SoC)
diff --git a/MAKEALL b/MAKEALL
index d63c5c2..a61e40c 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -548,6 +548,7 @@ LIST_ARM9=" \
cp926ejs \
cp946es \
cp966 \
+ da830evm \
imx27lite \
lpd7a400 \
mv88f6281gtw_ge \
diff --git a/Makefile b/Makefile
index a69e6d5..bf6081b 100644
--- a/Makefile
+++ b/Makefile
@@ -2927,6 +2927,9 @@ cp922_XA10_config \
cp1026_config: unconfig
@board/armltd/integrator/split_by_variant.sh cp $@
+da830evm_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs da830evm davinci davinci
+
davinci_dvevm_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs dvevm davinci davinci
diff --git a/include/common.h b/include/common.h
index 7df9afa..7fb107c 100644
--- a/include/common.h
+++ b/include/common.h
@@ -107,6 +107,9 @@ typedef volatile unsigned char vu_char;
#ifdef CONFIG_BLACKFIN
#include <asm/blackfin.h>
#endif
+#ifdef CONFIG_SOC_DA8XX
+#include <asm/arch/hardware.h>
+#endif
#include <part.h>
#include <flash.h>
diff --git a/include/configs/da830evm.h b/include/configs/da830evm.h
new file mode 100644
index 0000000..38e2ce1
--- /dev/null
+++ b/include/configs/da830evm.h
@@ -0,0 +1,243 @@
+/*
+ * Copyright (C) 2008 Texas Instruments, Inc <www.ti.com>
+ *
+ * Based on davinci_dvevm.h. Original Copyrights follow:
+ *
+ * Copyright (C) 2007 Sergey Kubushyn <ksi at koi8.net>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * Board
+ */
+
+/*
+ * SoC Configuration
+ */
+#define CONFIG_MACH_DAVINCI_DA830_EVM
+#define CONFIG_ARM926EJS /* arm926ejs CPU core */
+#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */
+#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
+#define CONFIG_SYS_OSCIN_FREQ 24000000
+#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
+#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
+#define CONFIG_SYS_HZ 1000
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
+
+/*
+ * Memory Info
+ */
+#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* reserved for initial data */
+#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
+#define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1 /* memtest start addr */
+#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024) /* 16MB test */
+#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
+#define CONFIG_STACKSIZE (256*1024) /* regular stack */
+
+/*
+ * Serial Driver info
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */
+#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
+#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
+#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
+#define CONFIG_BAUDRATE 115200 /* Default baud rate */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * I2C Configuration
+ */
+#define CONFIG_HARD_I2C
+#define CONFIG_DRIVER_DAVINCI_I2C
+#define CONFIG_SYS_I2C_SPEED 25000 /* 100Kbps won't work, H/W bug */
+#define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
+
+/*
+ * I2C EEPROM definitions for catalyst 24W256 EEPROM chip
+ */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
+
+/*
+ * Network & Ethernet Configuration
+ */
+#ifdef CONFIG_DRIVER_TI_EMAC
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT 10
+#define CONFIG_NET_MULTI
+#endif
+
+/*
+ * Flash & Environment
+ */
+#ifdef CONFIG_USE_NAND
+#undef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_NAND_DAVINCI
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
+#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
+#define CONFIG_ENV_SIZE (128 << 10)
+#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
+#define CONFIG_SYS_NAND_CS 3
+#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
+#define CONFIG_SYS_CLE_MASK 0x10
+#define CONFIG_SYS_ALE_MASK 0x8
+#define CONFIG_SYS_NAND_HW_ECC
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define NAND_MAX_CHIPS 1
+#define DEF_BOOTM ""
+#endif
+
+#ifdef CONFIG_USE_NOR
+#define CONFIG_ENV_IS_IN_FLASH
+#undef CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
+#define CONFIG_SYS_FLASH_SECT_SZ (64 << 10) /* 64KB */
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*3)
+#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
+#define PHYS_FLASH_SIZE (32 << 20) /* Flash size 32MB */
+#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
+#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ
+#define CONFIG_SYS_FLASH_SPL_ACCESS
+#endif
+
+#ifdef CONFIG_USE_SPIFLASH
+#undef CONFIG_ENV_IS_IN_FLASH
+#undef CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE (16 << 10)
+#define CONFIG_ENV_OFFSET (256 << 10)
+#define CONFIG_ENV_SECT_SIZE 4096
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_DAVINCI_SPI
+#define CONFIG_SYS_SPI_BASE DAVINCI_SPI0_BASE
+#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI0_CLKID)
+#define CONFIG_SF_DEFAULT_SPEED 50000000
+#define CONFIG_SYS_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#endif
+
+
+/*
+ * U-Boot general configuration
+ */
+#undef CONFIG_USE_IRQ /* No IRQ/FIQ in U-Boot */
+#undef CONFIG_MISC_INIT_R
+#undef CONFIG_BOOTDELAY
+#define CONFIG_BOOTFILE "uImage" /* Boot file name */
+#define CONFIG_SYS_PROMPT "DA830-evm > " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_MEMTEST_START + 0x700000)
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+
+/*
+ * Linux Information
+ */
+#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100)
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_BOOTARGS "mem=32M console=ttyS2,115200n8 root=/dev/mtdblock/2 rw noinitrd ip=dhcp"
+#define CONFIG_BOOTCOMMAND ""
+#define CONFIG_BOOTDELAY 3
+
+/*
+ * U-Boot commands
+ */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_MEMORY
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_SETGETDCR
+#define CONFIG_CMD_EEPROM
+
+#ifndef CONFIG_DRIVER_TI_EMAC
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_DHCP
+#undef CONFIG_CMD_MII
+#undef CONFIG_CMD_PING
+#endif
+
+#ifdef CONFIG_USE_NAND
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_UBI
+#define CONFIG_RBTREE
+#endif
+
+#ifdef CONFIG_USE_SPIFLASH
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_FLASH
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_SAVEENV
+#endif
+
+#if !defined(CONFIG_USE_NAND) && \
+ !defined(CONFIG_USE_NOR) && \
+ !defined(CONFIG_USE_SPIFLASH)
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_SIZE (16 << 10)
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_ENV
+#endif
+
+#ifdef CONFIG_USB_DA8XX
+#define CONFIG_CMD_USB /* include support for usb */
+#define CONFIG_CMD_STORAGE /* include support for usb */
+#define CONFIG_CMD_FAT /* include support for FAT/storage*/
+#define CONFIG_DOS_PARTITION /* include support for FAT/storage*/
+#endif
+
+#endif /* __CONFIG_H */
More information about the U-Boot
mailing list