[U-Boot] EHCI hub not powering on port

[Florian Fainelli]

Hi all,

I am trying to make u-boot work with my EHCI controler and everything goes well up to when it comes to powering on the port:

Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... New Device 0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x40
set address 1
usb_control_msg: request: 0x5, requesttype: 0x0, value 0x1 index 0x0 length 0x0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x12
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0x9
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0x19
get_conf_no 0 Result 25, wLength 25
if 0, ep 0
##EP epmaxpacketin[1] = 8
set configuration 1
usb_control_msg: request: 0x9, requesttype: 0x0, value 0x1 index 0x0 length 0x0
new device strings: Mfr=1, Product=2, SerialNumber=0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x300 index 0x0 length 0xFF
USB device number 1 default language ID 0x1
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x301 index 0x1 length 0xFF
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x302 index 0x1 length 0xFF
Manufacturer u-boot
Product      EHCI Host Controller
SerialNumber
USB hub found
usb_control_msg: request: 0x6, requesttype: 0xA0, value 0x2900 index 0x0 length 0x4
usb_control_msg: request: 0x6, requesttype: 0xA0, value 0x2900 index 0x0 length 0x8
1 ports detected
individual port power switching
standalone hub
individual port over-current protection
power on to power good time: 20ms
hub controller current requirement: 0mA
port 1 is removable
usb_control_msg: request: 0x0, requesttype: 0xA0, value 0x0 index 0x0 length 0x4
get_hub_status returned status 0001, change 0901
local power source is lost (inactive)
no over-current condition exists
enabling power on all ports
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x8 index 0x1 length 0x0
port 1 returns 0
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
Port 1 Status 0502 Change 0000
1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found


According to the USB 2.0 specification paragraph 11.11, this is the correct behavior since both HUB_STATUS_LOCAL_POWER in wHubStatus and 
HUB_CHANGE_LOCAL_POWER in wHubChange are set. Issuing a port power feature to the port would have no effect.

Has anyone already met similar problems with EHCI hubs integrated to EHCI controllers ?

Thank you very much in advance.