[U-Boot] [PATCH v3] Support for the OpenRD base board

Simon Kagstrom simon.kagstrom at netinsight.net
Mon Sep 14 09:46:30 CEST 2009


Support for the OpenRD base board

The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code and likely to be a bit incomplete.

Signed-off-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
---
The configuration does not include UBIFS support, which still needs
the remaining patches for the bitops cleanup and fixes:

  http://lists.denx.de/pipermail/u-boot/2009-August/059285.html

to build. Until those are applied, it's turned off here.


I get run-time problems when building for armv5te for OpenRD base
(apparently the same problem occurs for other Kirkwood boards). This
patch fixes that:

  http://lists.denx.de/pipermail/u-boot/2009-September/059896.html


ChangeLog:

v2: kwbimage.cfg, which is needed to produce an image to install on the
  NAND flash, has been added
v3: Updated after Prafullas review:
  * Correct typo in comment section :-)
  * Update copyright references
  * Correct bit meaning in kwbimage.cfg according to new specification
  * Add empty line after MPP configuration
  * Use short name for board identity string in config 
  * Use CONFIG_SHEEVA_88SV131 instead of Feroceon
  * Add CONFIG_KIRKWOOD_PCIE_INIT to config
  * Use config_cmd_default.h and remove options which are not needed anymore
  * Move config address to 0x60000 (384KB). I'd like it at this address since
    adding UBI/UBIFS support to U-boot makes the binary a bit more than 300KB
    and would thus overlap a config address at 0x40000.
  Not updated in v3:
  * The default MTD options are kept (useful for UBIFS)
  * eth init is not done, this needs to be done in a generic way

 MAINTAINERS                             |    4 +
 MAKEALL                                 |    1 +
 Makefile                                |    3 +
 board/Marvell/openrd_base/Makefile      |   56 ++++++++
 board/Marvell/openrd_base/config.mk     |   33 +++++
 board/Marvell/openrd_base/kwbimage.cfg  |  168 +++++++++++++++++++++++++
 board/Marvell/openrd_base/openrd_base.c |  160 +++++++++++++++++++++++
 board/Marvell/openrd_base/openrd_base.h |   46 +++++++
 include/configs/openrd_base.h           |  209 +++++++++++++++++++++++++++++++
 9 files changed, 680 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/openrd_base/Makefile
 create mode 100644 board/Marvell/openrd_base/config.mk
 create mode 100644 board/Marvell/openrd_base/kwbimage.cfg
 create mode 100644 board/Marvell/openrd_base/openrd_base.c
 create mode 100644 board/Marvell/openrd_base/openrd_base.h
 create mode 100644 include/configs/openrd_base.h

diff --git a/MAINTAINERS b/MAINTAINERS
index e9db278..99cdc12 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -588,6 +588,10 @@ Gary Jennejohn <garyj at denx.de>
 Konstantin Kletschke <kletschke at synertronixx.de>
 	scb9328		ARM920T
 
+Simon Kagstrom <simon.kagstrom at netinsight.net>
+
+       openrd_base     ARM926EJS (Kirkwood SoC)
+
 Nishant Kamat <nskamat at ti.com>
 
 	omap1610h2	ARM926EJS
diff --git a/MAKEALL b/MAKEALL
index f0ed8ea..9e6eee2 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -533,6 +533,7 @@ LIST_ARM9="			\
 	omap1610inn		\
 	omap5912osk		\
 	omap730p2		\
+	openrd_base		\
 	rd6281a			\
 	sbc2410x		\
 	scb9328			\
diff --git a/Makefile b/Makefile
index 9764cea..6cef82a 100644
--- a/Makefile
+++ b/Makefile
@@ -3022,6 +3022,9 @@ omap1610h2_cs_autoboot_config:	unconfig
 omap5912osk_config :	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk ti omap
 
+openrd_base_config: unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
 xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
 
 omap730p2_config \
diff --git a/board/Marvell/openrd_base/Makefile b/board/Marvell/openrd_base/Makefile
new file mode 100644
index 0000000..3ef0b9b
--- /dev/null
+++ b/board/Marvell/openrd_base/Makefile
@@ -0,0 +1,56 @@
+#
+# (C) Copyright 2009
+# Net Insight <www.netinsight.net>
+# Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
+#
+# Based on sheevaplug:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= openrd_base.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/openrd_base/config.mk b/board/Marvell/openrd_base/config.mk
new file mode 100644
index 0000000..8ae355e
--- /dev/null
+++ b/board/Marvell/openrd_base/config.mk
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2009
+# Net Insight <www.netinsight.net>
+# Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
+#
+# Based on sheevaplug:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
+
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
diff --git a/board/Marvell/openrd_base/kwbimage.cfg b/board/Marvell/openrd_base/kwbimage.cfg
new file mode 100644
index 0000000..757eb28
--- /dev/null
+++ b/board/Marvell/openrd_base/kwbimage.cfg
@@ -0,0 +1,168 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM	nand
+NAND_ECC_MODE	default
+NAND_PAGE_SIZE	0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30	# DDR Configuration register
+# bit13-0:  0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000	# DDR Controller Control Low
+# bit 4:    0=addr/cmd in smame cycle
+# bit 5:    0=clk is driven during self refresh, we don't care for APX
+# bit 6:    0=use recommended falling edge of clk for addr/cmd
+# bit14:    0=input buffer always powered up
+# bit18:    1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31:    0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
+# bit3-0:   TRAS lsbs
+# bit7-4:   TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20:    TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33	#  DDR Timing (High)
+# bit6-0:   TRFC
+# bit8-7:   TR2R
+# bit10-9:  TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x000000cc	#  DDR Address Control
+# bit1-0:   00, Cs0width=x8
+# bit3-2:   11, Cs0size=1Gb
+# bit5-4:   00, Cs1width=x8
+# bit7-6:   11, Cs1size=1Gb
+# bit9-8:   00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16:    0,  Cs0AddrSel
+# bit17:    0,  Cs1AddrSel
+# bit18:    0,  Cs2AddrSel
+# bit19:    0,  Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
+# bit0:    0,  OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000	#  DDR Operation
+# bit3-0:   0x0, DDR cmd
+# bit31-4:  0 required
+
+DATA 0xFFD0141C 0x00000C52	#  DDR Mode
+# bit2-0:   2, BurstLen=2 required
+# bit3:     0, BurstType=0 required
+# bit6-4:   4, CL=5
+# bit7:     0, TestMode=0 normal
+# bit8:     0, DLL reset=0 normal
+# bit11-9:  6, auto-precharge write recovery ????????????
+# bit12:    0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000042	#  DDR Extended Mode
+# bit0:    0,  DDR DLL enabled
+# bit1:    1,  DDR drive strength reduced
+# bit2:    0,  DDR ODT control lsd (disabled)
+# bit5-3:  000, required
+# bit6:    1,  DDR ODT control msb, (disabled)
+# bit9-7:  000, required
+# bit10:   0,  differential DQS enabled
+# bit11:   0, required
+# bit12:   0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
+# bit2-0:  111, required
+# bit3  :  1  , MBUS Burst Chop disabled
+# bit6-4:  111, required
+# bit7  :  0
+# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9  :  0  , no half clock cycle addition to dataout
+# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0    required
+
+DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
+# bit0:    1,  Window enabled
+# bit1:    0,  Write Protect disabled
+# bit3-2:  00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000	# CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x0FFFFFF5	# CS[1]n Size 256Mb Window enabled for CS1
+
+DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00120012	#  DDR ODT Control (Low)
+# bit3-0:   0010, (read) M_ODT[0] is asserted during read from DRAM CS1
+# bit7-4:   0001, (read) M_ODT[1] is asserted during read from DRAM CS0
+# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
+# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
+DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
+
+DATA 0xFFD0149C 0x0000E40f	# CPU ODT Control
+# bit3-0:    1111, internal ODT is asserted during read from DRAM bank 0-3
+# bit11-10:    01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
+# bit13-12:    10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
+# bit14:        1, M_STARTBURST_IN ODT: Enabled
+# bit15:        1, DDR IO ODT Unit: Use ODT block
+DATA 0xFFD01480 0x00000001	# DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/Marvell/openrd_base/openrd_base.c b/board/Marvell/openrd_base/openrd_base.c
new file mode 100644
index 0000000..c00a08a
--- /dev/null
+++ b/board/Marvell/openrd_base/openrd_base.c
@@ -0,0 +1,160 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
+ *
+ * Based on sheevaplug.c:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "openrd_base.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+	/*
+	 * default gpio configuration
+	 * There are maximum 64 gpios controlled through 2 sets of registers
+	 * the  below configuration configures mainly initial LED status
+	 */
+	kw_config_gpio(OPENRD_OE_VAL_LOW,
+			OPENRD_OE_VAL_HIGH,
+			OPENRD_OE_LOW, OPENRD_OE_HIGH);
+
+	/* Multi-Purpose Pins Functionality configuration */
+	u32 kwmpp_config[] = {
+		MPP0_NF_IO2,
+		MPP1_NF_IO3,
+		MPP2_NF_IO4,
+		MPP3_NF_IO5,
+		MPP4_NF_IO6,
+		MPP5_NF_IO7,
+		MPP6_SYSRST_OUTn,
+		MPP7_GPO,
+		MPP8_TW_SDA,
+		MPP9_TW_SCK,
+		MPP10_UART0_TXD,
+		MPP11_UART0_RXD,
+		MPP12_SD_CLK,
+		MPP13_SD_CMD, /* Alt UART1_TXD */
+		MPP14_SD_D0,  /* Alt UART1_RXD */
+		MPP15_SD_D1,
+		MPP16_SD_D2,
+		MPP17_SD_D3,
+		MPP18_NF_IO0,
+		MPP19_NF_IO1,
+		MPP20_GE1_0,
+		MPP21_GE1_1,
+		MPP22_GE1_2,
+		MPP23_GE1_3,
+		MPP24_GE1_4,
+		MPP25_GE1_5,
+		MPP26_GE1_6,
+		MPP27_GE1_7,
+		MPP28_GPIO,
+		MPP29_TSMP9,
+		MPP30_GE1_10,
+		MPP31_GE1_11,
+		MPP32_GE1_12,
+		MPP33_GE1_13,
+		MPP34_GPIO,   /* UART1 / SD sel */
+		MPP35_TDM_CH0_TX_QL,
+		MPP36_TDM_SPI_CS1,
+		MPP37_TDM_CH2_TX_QL,
+		MPP38_TDM_CH2_RX_QL,
+		MPP39_AUDIO_I2SBCLK,
+		MPP40_AUDIO_I2SDO,
+		MPP41_AUDIO_I2SLRC,
+		MPP42_AUDIO_I2SMCLK,
+		MPP43_AUDIO_I2SDI,
+		MPP44_AUDIO_EXTCLK,
+		MPP45_TDM_PCLK,
+		MPP46_TDM_FS,
+		MPP47_TDM_DRX,
+		MPP48_TDM_DTX,
+		MPP49_TDM_CH0_RX_QL,
+		0
+	};
+
+	kirkwood_mpp_conf(kwmpp_config);
+
+	/*
+	 * arch number of board
+	 */
+	gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+	return 0;
+}
+
+int dram_init(void)
+{
+	int i;
+
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+	}
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+	u16 reg;
+	u16 devadr;
+	char *name = "egiga0";
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	/* command to read PHY dev address */
+	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+		printf("Err..%s could not read PHY dev address\n",
+			__FUNCTION__);
+		return;
+	}
+
+	/*
+	 * Enable RGMII delay on Tx and Rx for CPU port
+	 * Ref: sec 4.7.2 of chip datasheet
+	 */
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
+	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+	/* reset the phy */
+	miiphy_reset(name, devadr);
+
+	printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/openrd_base/openrd_base.h b/board/Marvell/openrd_base/openrd_base.h
new file mode 100644
index 0000000..f3daf17
--- /dev/null
+++ b/board/Marvell/openrd_base/openrd_base.h
@@ -0,0 +1,46 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __OPENRD_BASE_H
+#define __OPENRD_BASE_H
+
+#define OPENRD_OE_LOW		(~(1<<28))        /* RS232 / RS485 */
+#define OPENRD_OE_HIGH		(~(1<<2))         /* SD / UART1 */
+#define OPENRD_OE_VAL_LOW		(0)       /* Sel RS232 */
+#define OPENRD_OE_VAL_HIGH		(1 << 2)  /* Sel SD */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG		10
+#define MV88E1116_CPRSP_CR3_REG		21
+#define MV88E1116_MAC_CTRL_REG		21
+#define MV88E1116_PGADR_REG		22
+#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
+
+#endif /* __OPENRD_BASE_H */
diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h
new file mode 100644
index 0000000..aea0dfb
--- /dev/null
+++ b/include/configs/openrd_base.h
@@ -0,0 +1,209 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_OPENRD_BASE_H
+#define _CONFIG_OPENRD_BASE_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING	"\nOpenRD_base"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL		1
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+#define CONFIG_SHEEVA_88SV131	1	/* CPU Core subversion */
+#define CONFIG_KIRKWOOD		1	/* SOC Family Name */
+#define CONFIG_KW88F6281	1	/* SOC Name */
+#define CONFIG_MACH_OPENRD_BASE	/* Machine type */
+
+#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ		1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1		KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX	1	/*Console on UART0 */
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, \
+					  115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY	3	/* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs  */
+#define CONFIG_INITRD_TAG	1	/* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1	/* enable memory tag */
+
+#define	CONFIG_SYS_PROMPT	"Marvell>> "	/* Command Prompt */
+#define	CONFIG_SYS_CBSIZE	1024	/* Console I/O Buff Size */
+#define	CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE \
+		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define NAND_MAX_CHIPS			1
+#define CONFIG_SYS_NAND_BASE		0xD8000000	/* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL		1
+#define CONFIG_SYS_64BIT_VSPRINTF	/* needed for nand_util.c */
+#endif
+
+/*
+ *  Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND		1
+#define CONFIG_ENV_SECT_SIZE		0x20000	/* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE		1	/* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE			0x20000	/* 128k */
+#define CONFIG_ENV_ADDR			0x60000
+#define CONFIG_ENV_OFFSET		0x60000	/* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND		"${x_bootcmd_kernel}; "	\
+	"setenv bootargs ${x_bootargs} ${x_bootargs_root}; "	\
+	"${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define MTDIDS_DEFAULT		"nand0=nand_mtd"
+#define MTDPARTS_DEFAULT	"mtdparts=nand_mtd:0x100000 at 0x000000(uboot),"\
+	"0x400000 at 0x100000(uImage),"\
+	"0x1fb00000 at 0x500000(rootfs)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS	"x_bootargs=console"		\
+	"=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0"		\
+	"x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0"	\
+	"x_bootcmd_usb=usb start\0"					\
+	"x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0"		\
+	"mtdids="MTDIDS_DEFAULT"\0"					\
+	"mtdparts="MTDPARTS_DEFAULT"\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN	(1024 * 1024) /* 1MiB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE	128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT	/* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO	/* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS	4
+#define CONFIG_STACKSIZE	0x00100000	/* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR	0x00800000	/* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000	/* 4M */
+#define CONFIG_SYS_MEMTEST_END	0x007fffff	/*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE	/* include NetConsole support   */
+#define CONFIG_NET_MULTI	/* specify more that one ports available */
+#define	CONFIG_MII		/* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA	/* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS	{1,0}	/* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR	0x8
+#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI			/* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD	/* on Kirkwood platform	*/
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+#endif /* _CONFIG_OPENRD_BASE_H */
-- 
1.6.0.4



More information about the U-Boot mailing list