[U-Boot] [PATCH v2] TI: OMAP3: Overo Tobi ethernet support

Tom Tom.Rix at windriver.com
Thu Sep 24 19:32:19 CEST 2009 

Olof Johansson wrote:
> Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
> over tftp.
> 
> Based on the omap3 evm code. I added a new highlevel define for Tobi
> to avoid having it dependent on CMD_NET (which would seem backward in
> this case).
> 
> Signed-off-by: Olof Johansson <olof at lixom.net>

Ack-ed

Sandeep,
Can you push this to the ti branch?

Tom

> ---
> 
> This version of the patch fixes whitespace comments from WD, and includes
> fixes for the build warnings that Dirk's patch also silenced.
> 
> 
>  board/overo/overo.c           |   62 +++++++++++++++++++++++++++++++++++++++++
>  board/overo/overo.h           |   37 ++++++++++++++++++++++++
>  include/configs/omap3_overo.h |   23 ++++++++++++++-
>  3 files changed, 120 insertions(+), 2 deletions(-)
> 
> diff --git a/board/overo/overo.c b/board/overo/overo.c
> index dd6d286..7d87e52 100644
> --- a/board/overo/overo.c
> +++ b/board/overo/overo.c
> @@ -29,13 +29,19 @@
>   * MA 02111-1307 USA
>   */
>  #include <common.h>
> +#include <netdev.h>
>  #include <twl4030.h>
>  #include <asm/io.h>
>  #include <asm/arch/mux.h>
> +#include <asm/arch/mem.h>
>  #include <asm/arch/sys_proto.h>
>  #include <asm/mach-types.h>
>  #include "overo.h"
>  
> +#if defined(CONFIG_OMAP3_OVERO_TOBI)
> +static void setup_net_chip(void);
> +#endif
> +
>  /*
>   * Routine: board_init
>   * Description: Early hardware init.
> @@ -62,6 +68,10 @@ int misc_init_r(void)
>  	twl4030_power_init();
>  	twl4030_led_init();
>  
> +#if defined(CONFIG_OMAP3_OVERO_TOBI)
> +	setup_net_chip();
> +#endif
> +
>  	dieid_num_r();
>  
>  	return 0;
> @@ -76,4 +86,56 @@ int misc_init_r(void)
>  void set_muxconf_regs(void)
>  {
>  	MUX_OVERO();
> +#if defined(CONFIG_OMAP3_OVERO_TOBI)
> +	MUX_OVERO_TOBI();
> +#endif
> +}
> +
> +#if defined(CONFIG_OMAP3_OVERO_TOBI)
> +/*
> + * Routine: setup_net_chip
> + * Description: Setting up the configuration GPMC registers specific to the
> + *	      Ethernet hardware.
> + */
> +static void setup_net_chip(void)
> +{
> +	struct gpio *gpio3_base = (struct gpio *)OMAP34XX_GPIO3_BASE;
> +	struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
> +
> +	/* Configure GPMC registers */
> +	writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[5].config1);
> +	writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[5].config2);
> +	writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[5].config3);
> +	writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[5].config4);
> +	writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[5].config5);
> +	writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[5].config6);
> +	writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[5].config7);
> +
> +	/* Enable off mode for NWE in PADCONF_GPMC_NWE register */
> +	writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
> +	/* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
> +	writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
> +	/* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
> +	writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
> +		&ctrl_base->gpmc_nadv_ale);
> +
> +	/* Make GPIO 64 as output pin */
> +	writel(readl(&gpio3_base->oe) & ~(GPIO0), &gpio3_base->oe);
> +
> +	/* Now send a pulse on the GPIO pin */
> +	writel(GPIO0, &gpio3_base->setdataout);
> +	udelay(1);
> +	writel(GPIO0, &gpio3_base->cleardataout);
> +	udelay(1);
> +	writel(GPIO0, &gpio3_base->setdataout);
> +}
> +#endif
> +
> +int board_eth_init(bd_t *bis)
> +{
> +	int rc = 0;
> +#ifdef CONFIG_SMC911X
> +	rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
> +#endif
> +	return rc;
>  }
> diff --git a/board/overo/overo.h b/board/overo/overo.h
> index d9fe74e..48d58f2 100644
> --- a/board/overo/overo.h
> +++ b/board/overo/overo.h
> @@ -378,4 +378,41 @@ const omap3_sysinfo sysinfo = {
>  	MUX_VAL(CP(SDRC_CKE0),		(IDIS | PTU | EN  | M0)) /*sdrc_cke0*/\
>  	MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTU | EN  | M0)) /*sdrc_cke1*/
>  
> +#if defined(CONFIG_OMAP3_OVERO_TOBI)
> +#define MUX_OVERO_TOBI() \
> +	MUX_VAL(CP(GPMC_A1),		(IDIS | PTU | EN  | M0)) /*GPMC_A1*/\
> +	MUX_VAL(CP(GPMC_A2),		(IDIS | PTU | EN  | M0)) /*GPMC_A2*/\
> +	MUX_VAL(CP(GPMC_A3),		(IDIS | PTU | EN  | M0)) /*GPMC_A3*/\
> +	MUX_VAL(CP(GPMC_A4),		(IDIS | PTU | EN  | M0)) /*GPMC_A4*/\
> +	MUX_VAL(CP(GPMC_A5),		(IDIS | PTU | EN  | M0)) /*GPMC_A5*/\
> +	MUX_VAL(CP(GPMC_A6),		(IDIS | PTU | EN  | M0)) /*GPMC_A6*/\
> +	MUX_VAL(CP(GPMC_A7),		(IDIS | PTU | EN  | M0)) /*GPMC_A7*/\
> +	MUX_VAL(CP(GPMC_A8),		(IDIS | PTU | EN  | M0)) /*GPMC_A8*/\
> +	MUX_VAL(CP(GPMC_A9),		(IDIS | PTU | EN  | M0)) /*GPMC_A9*/\
> +	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | EN  | M0)) /*GPMC_A10*/\
> +	MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0)) /*GPMC_D0*/\
> +	MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0)) /*GPMC_D1*/\
> +	MUX_VAL(CP(GPMC_D2),		(IEN  | PTU | EN  | M0)) /*GPMC_D2*/\
> +	MUX_VAL(CP(GPMC_D3),		(IEN  | PTU | EN  | M0)) /*GPMC_D3*/\
> +	MUX_VAL(CP(GPMC_D4),		(IEN  | PTU | EN  | M0)) /*GPMC_D4*/\
> +	MUX_VAL(CP(GPMC_D5),		(IEN  | PTU | EN  | M0)) /*GPMC_D5*/\
> +	MUX_VAL(CP(GPMC_D6),		(IEN  | PTU | EN  | M0)) /*GPMC_D6*/\
> +	MUX_VAL(CP(GPMC_D7),		(IEN  | PTU | EN  | M0)) /*GPMC_D7*/\
> +	MUX_VAL(CP(GPMC_D8),		(IEN  | PTU | EN  | M0)) /*GPMC_D8*/\
> +	MUX_VAL(CP(GPMC_D9),		(IEN  | PTU | EN  | M0)) /*GPMC_D9*/\
> +	MUX_VAL(CP(GPMC_D10),		(IEN  | PTU | EN  | M0)) /*GPMC_D10*/\
> +	MUX_VAL(CP(GPMC_D11),		(IEN  | PTU | EN  | M0)) /*GPMC_D11*/\
> +	MUX_VAL(CP(GPMC_D12),		(IEN  | PTU | EN  | M0)) /*GPMC_D12*/\
> +	MUX_VAL(CP(GPMC_D13),		(IEN  | PTU | EN  | M0)) /*GPMC_D13*/\
> +	MUX_VAL(CP(GPMC_D14),		(IEN  | PTU | EN  | M0)) /*GPMC_D14*/\
> +	MUX_VAL(CP(GPMC_D15),		(IEN  | PTU | EN  | M0)) /*GPMC_D15*/\
> +	MUX_VAL(CP(GPMC_NCS5),		(IDIS | PTU | EN  | M0)) /*GPMC_nCS5*/\
> +	MUX_VAL(CP(GPMC_CLK),		(IDIS | PTU | EN  | M0)) /*GPMC_CLK*/\
> +	MUX_VAL(CP(GPMC_WAIT2),		(IEN  | PTU | EN  | M4)) /*GPIO_64*/\
> +								 /* - SMSC911X_NRES*/\
> +	MUX_VAL(CP(MCSPI1_CS2),		(IEN  | PTU | DIS | M4)) /*GPIO_176 */\
> +								 /* - LAN_INTR */
> +
> +#endif
> +
>  #endif
> diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
> index 07a031b..3faf756 100644
> --- a/include/configs/omap3_overo.h
> +++ b/include/configs/omap3_overo.h
> @@ -28,7 +28,10 @@
>  #define CONFIG_OMAP		1	/* in a TI OMAP core */
>  #define CONFIG_OMAP34XX		1	/* which is a 34XX */
>  #define CONFIG_OMAP3430		1	/* which is in a 3430 */
> -#define CONFIG_OMAP3_OVERO		1	/* working with overo */
> +#define CONFIG_OMAP3_OVERO	1	/* working with overo */
> +
> +/* Change the below line to define 1 if you want ethernet on Tobi */
> +#undef CONFIG_OMAP3_OVERO_TOBI		/* overo mounted on tobi */
>  
>  #include <asm/arch/cpu.h>	/* get chip and board defs */
>  #include <asm/arch/omap3.h>
> @@ -105,9 +108,12 @@
>  #undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
>  #undef CONFIG_CMD_IMI		/* iminfo			*/
>  #undef CONFIG_CMD_IMLS		/* List all found images	*/
> -#undef CONFIG_CMD_NET		/* bootp, tftpboot, rarpboot	*/
>  #undef CONFIG_CMD_NFS		/* NFS support			*/
>  
> +#if !defined(CONFIG_OMAP3_OVERO_TOBI)
> +#undef CONFIG_CMD_NET		/* bootp, tftpboot, rarpboot	*/
> +#endif
> +
>  #define CONFIG_SYS_NO_FLASH
>  #define CONFIG_SYS_I2C_SPEED		100000
>  #define CONFIG_SYS_I2C_SLAVE		1
> @@ -293,4 +299,17 @@ extern unsigned int boot_flash_sec;
>  extern unsigned int boot_flash_type;
>  #endif
>  
> +#if defined(CONFIG_OMAP3_OVERO_TOBI)
> +/*----------------------------------------------------------------------------
> + * SMSC9115 Ethernet from SMSC9118 family
> + *----------------------------------------------------------------------------
> + */
> +
> +#define CONFIG_NET_MULTI
> +#define CONFIG_SMC911X		1
> +#define CONFIG_SMC911X_32_BIT
> +#define CONFIG_SMC911X_BASE     0x2C000000
> +
> +#endif /* (CONFIG_CMD_NET) */
> +
>  #endif				/* __CONFIG_H */

More information about the U-Boot mailing list