[PATCH] mpc83xx: retain POR values of non-configured ACR, SPCR, SCCR, and LCRR bitfields
Kim Phillips
kim.phillips at freescale.com
Sat Sep 26 01:07:29 CEST 2009
some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurations might omit
setting e.g., DBYP since it was not documented in their SoC's RM.
Prevent them bricking their board by retaining power on reset values
in bit fields that the board porter doesn't explicitly configure
via CONFIG_SYS_<registername>_<bitfield> assignments in the board
config file.
also start to use i/o accessors.
Signed-off-by: Kim Phillips <kim.phillips at freescale.com>
---
cpu/mpc83xx/cpu_init.c | 255 ++++++++++++++++++++++++-----------------
include/configs/MPC8313ERDB.h | 3 +-
include/configs/MPC8315ERDB.h | 3 +-
include/configs/MPC8323ERDB.h | 3 +-
include/configs/MPC832XEMDS.h | 3 +-
include/configs/MPC8349EMDS.h | 3 +-
include/configs/MPC8349ITX.h | 3 +-
include/configs/MPC8360EMDS.h | 3 +-
include/configs/MPC8360ERDK.h | 3 +-
include/configs/MPC837XEMDS.h | 3 +-
include/configs/MPC837XERDB.h | 3 +-
include/configs/MVBLM7.h | 3 +-
include/configs/SIMPC8313.h | 4 +-
include/configs/TQM834x.h | 3 +-
include/configs/kmeter1.h | 4 +-
include/configs/sbc8349.h | 3 +-
include/configs/vme8349.h | 3 +-
17 files changed, 183 insertions(+), 122 deletions(-)
diff --git a/cpu/mpc83xx/cpu_init.c b/cpu/mpc83xx/cpu_init.c
index 5c930d3..95dbc76 100644
--- a/cpu/mpc83xx/cpu_init.c
+++ b/cpu/mpc83xx/cpu_init.c
@@ -23,8 +23,8 @@
#include <common.h>
#include <mpc83xx.h>
#include <ioports.h>
-#ifdef CONFIG_USB_EHCI_FSL
#include <asm/io.h>
+#ifdef CONFIG_USB_EHCI_FSL
#include <usb/ehci-fsl.h>
#endif
@@ -63,149 +63,192 @@ static void config_qe_ioports(void)
*/
void cpu_init_f (volatile immap_t * im)
{
- /* Pointer is writable since we allocated a register for it */
- gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
-
- /* Clear initial global data */
- memset ((void *) gd, 0, sizeof (gd_t));
-
- /* system performance tweaking */
-
-#ifdef CONFIG_SYS_ACR_PIPE_DEP
- /* Arbiter pipeline depth */
- im->arbiter.acr = (im->arbiter.acr & ~ACR_PIPE_DEP) |
- (CONFIG_SYS_ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT);
+ __be32 acr_mask =
+#ifdef CONFIG_SYS_ACR_PIPE_DEP /* Arbiter pipeline depth */
+ (ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_ACR_RPTCNT
- /* Arbiter repeat count */
- im->arbiter.acr = (im->arbiter.acr & ~(ACR_RPTCNT)) |
- (CONFIG_SYS_ACR_RPTCNT << ACR_RPTCNT_SHIFT);
+#ifdef CONFIG_SYS_ACR_RPTCNT /* Arbiter repeat count */
+ (ACR_RPTCNT << ACR_RPTCNT_SHIFT) |
#endif
-
+ 0;
+ __be32 acr_val =
+#ifdef CONFIG_SYS_ACR_PIPE_DEP /* Arbiter pipeline depth */
+ (CONFIG_SYS_ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_ACR_RPTCNT /* Arbiter repeat count */
+ (CONFIG_SYS_ACR_RPTCNT << ACR_RPTCNT_SHIFT) |
+#endif
+ 0;
+ __be32 spcr_mask =
+#ifdef CONFIG_SYS_SPCR_OPT /* Optimize transactions between CSB and other dev */
+ (SPCR_OPT << SPCR_OPT_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SPCR_TSECEP /* all eTSEC's Emergency priority */
+ (SPCR_TSECEP << SPCR_TSECEP_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SPCR_TSEC1EP /* TSEC1 Emergency priority */
+ (SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SPCR_TSEC2EP /* TSEC2 Emergency priority */
+ (SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT) |
+#endif
+ 0;
+ __be32 spcr_val =
#ifdef CONFIG_SYS_SPCR_OPT
- /* Optimize transactions between CSB and other devices */
- im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_OPT) |
- (CONFIG_SYS_SPCR_OPT << SPCR_OPT_SHIFT);
+ (CONFIG_SYS_SPCR_OPT << SPCR_OPT_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SPCR_TSECEP
- /* all eTSEC's Emergency priority */
- im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSECEP) |
- (CONFIG_SYS_SPCR_TSECEP << SPCR_TSECEP_SHIFT);
+#ifdef CONFIG_SYS_SPCR_TSECEP /* all eTSEC's Emergency priority */
+ (CONFIG_SYS_SPCR_TSECEP << SPCR_TSECEP_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SPCR_TSEC1EP
- /* TSEC1 Emergency priority */
- im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC1EP) |
- (CONFIG_SYS_SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT);
+#ifdef CONFIG_SYS_SPCR_TSEC1EP /* TSEC1 Emergency priority */
+ (CONFIG_SYS_SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SPCR_TSEC2EP
- /* TSEC2 Emergency priority */
- im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC2EP) |
- (CONFIG_SYS_SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT);
+#ifdef CONFIG_SYS_SPCR_TSEC2EP /* TSEC2 Emergency priority */
+ (CONFIG_SYS_SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_ENCCM
- /* Encryption clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_ENCCM) |
- (CONFIG_SYS_SCCR_ENCCM << SCCR_ENCCM_SHIFT);
+ 0;
+ __be32 sccr_mask =
+#ifdef CONFIG_SYS_SCCR_ENCCM /* Encryption clock mode */
+ (SCCR_ENCCM << SCCR_ENCCM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_PCICM
- /* PCI & DMA clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_PCICM) |
- (CONFIG_SYS_SCCR_PCICM << SCCR_PCICM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_PCICM /* PCI & DMA clock mode */
+ (SCCR_PCICM << SCCR_PCICM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_TSECCM
- /* all TSEC's clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSECCM) |
- (CONFIG_SYS_SCCR_TSECCM << SCCR_TSECCM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_TSECCM /* all TSEC's clock mode */
+ (SCCR_TSECCM << SCCR_TSECCM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_TSEC1CM
- /* TSEC1 clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1CM) |
- (CONFIG_SYS_SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_TSEC1CM /* TSEC1 clock mode */
+ (SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_TSEC2CM
- /* TSEC2 clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2CM) |
- (CONFIG_SYS_SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_TSEC2CM /* TSEC2 clock mode */
+ (SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_TSEC1ON
- /* TSEC1 clock switch */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1ON) |
- (CONFIG_SYS_SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT);
+#ifdef CONFIG_SYS_SCCR_TSEC1ON /* TSEC1 clock switch */
+ (SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_TSEC2ON
- /* TSEC2 clock switch */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2ON) |
- (CONFIG_SYS_SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT);
+#ifdef CONFIG_SYS_SCCR_TSEC2ON /* TSEC2 clock switch */
+ (SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_USBMPHCM
- /* USB MPH clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_USBMPHCM) |
- (CONFIG_SYS_SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_USBMPHCM /* USB MPH clock mode */
+ (SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_USBDRCM
- /* USB DR clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_USBDRCM) |
- (CONFIG_SYS_SCCR_USBDRCM << SCCR_USBDRCM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_USBDRCM /* USB DR clock mode */
+ (SCCR_USBDRCM << SCCR_USBDRCM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_SATACM
- /* SATA controller clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_SATACM) |
- (CONFIG_SYS_SCCR_SATACM << SCCR_SATACM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_SATACM /* SATA controller clock mode */
+ (SCCR_SATACM << SCCR_SATACM_SHIFT) |
+#endif
+ 0;
+ __be32 sccr_val =
+#ifdef CONFIG_SYS_SCCR_ENCCM /* Encryption clock mode */
+ (CONFIG_SYS_SCCR_ENCCM << SCCR_ENCCM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_PCICM /* PCI & DMA clock mode */
+ (CONFIG_SYS_SCCR_PCICM << SCCR_PCICM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_TSECCM /* all TSEC's clock mode */
+ (CONFIG_SYS_SCCR_TSECCM << SCCR_TSECCM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_TSEC1CM /* TSEC1 clock mode */
+ (CONFIG_SYS_SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_TSEC2CM /* TSEC2 clock mode */
+ (CONFIG_SYS_SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_TSEC1ON /* TSEC1 clock switch */
+ (CONFIG_SYS_SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_TSEC2ON /* TSEC2 clock switch */
+ (CONFIG_SYS_SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_USBMPHCM /* USB MPH clock mode */
+ (CONFIG_SYS_SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_USBDRCM /* USB DR clock mode */
+ (CONFIG_SYS_SCCR_USBDRCM << SCCR_USBDRCM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_SATACM /* SATA controller clock mode */
+ (CONFIG_SYS_SCCR_SATACM << SCCR_SATACM_SHIFT) |
+#endif
+ 0;
+ __be32 lcrr_mask =
+#ifdef CONFIG_SYS_LCRR_DBYP /* PLL bypass */
+ LCRR_DBYP |
+#endif
+#ifdef CONFIG_SYS_LCRR_EADC /* external address delay */
+ LCRR_EADC |
+#endif
+#ifdef CONFIG_SYS_LCRR_CLKDIV /* system clock divider */
+ LCRR_CLKDIV |
#endif
+ 0;
+ __be32 lcrr_val =
+#ifdef CONFIG_SYS_LCRR_DBYP /* PLL bypass */
+ CONFIG_SYS_LCRR_DBYP |
+#endif
+#ifdef CONFIG_SYS_LCRR_EADC
+ CONFIG_SYS_LCRR_EADC |
+#endif
+#ifdef CONFIG_SYS_LCRR_CLKDIV /* system clock divider */
+ CONFIG_SYS_LCRR_CLKDIV |
+#endif
+ 0;
+
+ /* Pointer is writable since we allocated a register for it */
+ gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
+
+ /* Clear initial global data */
+ memset ((void *) gd, 0, sizeof (gd_t));
+
+ /* system performance tweaking */
+ clrsetbits_be32(&im->arbiter.acr, acr_mask, acr_val);
+
+ clrsetbits_be32(&im->sysconf.spcr, spcr_mask, spcr_val);
+
+ clrsetbits_be32(&im->clk.sccr, sccr_mask, sccr_val);
/* RSR - Reset Status Register - clear all status (4.6.1.3) */
- gd->reset_status = im->reset.rsr;
- im->reset.rsr = ~(RSR_RES);
+ gd->reset_status = __raw_readl(&im->reset.rsr);
+ __raw_writel(~(RSR_RES), &im->reset.rsr);
/* AER - Arbiter Event Register - store status */
- gd->arbiter_event_attributes = im->arbiter.aeatr;
- gd->arbiter_event_address = im->arbiter.aeadr;
+ gd->arbiter_event_attributes = __raw_readl(&im->arbiter.aeatr);
+ gd->arbiter_event_address = __raw_readl(&im->arbiter.aeadr);
/*
* RMR - Reset Mode Register
* contains checkstop reset enable (4.6.1.4)
*/
- im->reset.rmr = (RMR_CSRE & (1<<RMR_CSRE_SHIFT));
+ __raw_writel(RMR_CSRE & (1<<RMR_CSRE_SHIFT), &im->reset.rmr);
- /* LCRR - Clock Ratio Register (10.3.1.16) */
- im->lbus.lcrr = CONFIG_SYS_LCRR;
+ /* LCRR - Clock Ratio Register (10.3.1.16)
+ * write, read, and isync per MPC8379ERM rev.1 CLKDEV field description
+ */
+ clrsetbits_be32(&im->lbus.lcrr, lcrr_mask, lcrr_val);
+ __raw_readl(&im->lbus.lcrr);
+ isync();
- /* Enable Time Base & Decrimenter ( so we will have udelay() )*/
- im->sysconf.spcr |= SPCR_TBEN;
+ /* Enable Time Base & Decrementer ( so we will have udelay() )*/
+ setbits_be32(&im->sysconf.spcr, SPCR_TBEN);
/* System General Purpose Register */
#ifdef CONFIG_SYS_SICRH
#if defined(CONFIG_MPC834x) || defined(CONFIG_MPC8313)
/* regarding to MPC34x manual rev.1 bits 28..29 must be preserved */
- im->sysconf.sicrh = (im->sysconf.sicrh & 0x0000000C) | CONFIG_SYS_SICRH;
+ __raw_writel((im->sysconf.sicrh & 0x0000000C) | CONFIG_SYS_SICRH,
+ &im->sysconf.sicrh);
#else
- im->sysconf.sicrh = CONFIG_SYS_SICRH;
+ __raw_writel(CONFIG_SYS_SICRH, &im->sysconf.sicrh);
#endif
#endif
#ifdef CONFIG_SYS_SICRL
- im->sysconf.sicrl = CONFIG_SYS_SICRL;
+ __raw_writel(CONFIG_SYS_SICRL, &im->sysconf.sicrl);
#endif
- /* DDR control driver register */
-#ifdef CONFIG_SYS_DDRCDR
- im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR;
+#ifdef CONFIG_SYS_DDRCDR /* DDR control driver register */
+ __raw_writel(CONFIG_SYS_DDRCDR, &im->sysconf.ddrcdr);
#endif
- /* Output buffer impedance register */
-#ifdef CONFIG_SYS_OBIR
- im->sysconf.obir = CONFIG_SYS_OBIR;
+#ifdef CONFIG_SYS_OBIR /* Output buffer impedance register */
+ __raw_writel(CONFIG_SYS_OBIR, &im->sysconf.obir);
#endif
#ifdef CONFIG_QE
@@ -308,7 +351,7 @@ void cpu_init_f (volatile immap_t * im)
/* Wait for clock to stabilize */
do {
- temp = in_be32(&ehci->control);
+ temp = __raw_readl(&ehci->control);
udelay(1000);
} while (!(temp & PHY_CLK_VALID));
#endif
diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h
index 76b7894..5927e76 100644
--- a/include/configs/MPC8313ERDB.h
+++ b/include/configs/MPC8313ERDB.h
@@ -216,7 +216,8 @@
/*
* Local Bus LCRR and LBCR regs
*/
-#define CONFIG_SYS_LCRR LCRR_EADC_1 | LCRR_CLKDIV_4
+#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR ( 0x00040000 /* TODO */ \
| (0xFF << LBCR_BMT_SHIFT) \
| 0xF ) /* 0x0004ff0f */
diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h
index 84cc9fa..8eaff5d 100644
--- a/include/configs/MPC8315ERDB.h
+++ b/include/configs/MPC8315ERDB.h
@@ -182,7 +182,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00040000
/*
diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
index c40d3d3..356586c 100644
--- a/include/configs/MPC8323ERDB.h
+++ b/include/configs/MPC8323ERDB.h
@@ -170,7 +170,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h
index f16616c..f17f9c7 100644
--- a/include/configs/MPC832XEMDS.h
+++ b/include/configs/MPC832XEMDS.h
@@ -159,7 +159,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index 9b2d25a..6361c45 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -206,7 +206,8 @@
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h
index 3b4e344..eaa59fd 100644
--- a/include/configs/MPC8349ITX.h
+++ b/include/configs/MPC8349ITX.h
@@ -317,7 +317,8 @@ boards, we say we have two, but don't display a message if we find only one. */
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
#define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h
index b072e84..859705a 100644
--- a/include/configs/MPC8360EMDS.h
+++ b/include/configs/MPC8360EMDS.h
@@ -185,7 +185,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h
index cb0535c..6cee78a 100644
--- a/include/configs/MPC8360ERDK.h
+++ b/include/configs/MPC8360ERDK.h
@@ -177,7 +177,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h
index a190a50..abeb6a2 100644
--- a/include/configs/MPC837XEMDS.h
+++ b/include/configs/MPC837XEMDS.h
@@ -220,7 +220,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h
index 89fafe7..7ef92f7 100644
--- a/include/configs/MPC837XERDB.h
+++ b/include/configs/MPC837XERDB.h
@@ -243,7 +243,8 @@
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
diff --git a/include/configs/MVBLM7.h b/include/configs/MVBLM7.h
index 9835567..f8b016f 100644
--- a/include/configs/MVBLM7.h
+++ b/include/configs/MVBLM7.h
@@ -137,7 +137,8 @@
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/* LB sdram refresh timer, about 6us */
diff --git a/include/configs/SIMPC8313.h b/include/configs/SIMPC8313.h
index 866ff17..f68d834 100644
--- a/include/configs/SIMPC8313.h
+++ b/include/configs/SIMPC8313.h
@@ -111,7 +111,9 @@
/*
* Local Bus LCRR and LBCR regs
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_EADC_1 | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR (0x00040000 /* TODO */ \
| (0xFF << LBCR_BMT_SHIFT) \
| 0xF ) /* 0x0004ff0f */
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index da08b7c..4c909e6 100644
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -52,7 +52,8 @@
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
/* board pre init: do not call, nothing to do */
#undef CONFIG_BOARD_EARLY_INIT_F
diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h
index 79d8638..bec08da 100644
--- a/include/configs/kmeter1.h
+++ b/include/configs/kmeter1.h
@@ -170,7 +170,9 @@
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_EADC_2 | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_EADC LCRR_EADC_2
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
/*
* Init Local Bus Memory Controller:
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
index e961bb3..651deb5 100644
--- a/include/configs/sbc8349.h
+++ b/include/configs/sbc8349.h
@@ -182,7 +182,8 @@
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */
diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h
index 5304ec9..d0690fe 100644
--- a/include/configs/vme8349.h
+++ b/include/configs/vme8349.h
@@ -178,7 +178,8 @@
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */
--
1.6.4.4
More information about the U-Boot
mailing list