[U-Boot] [PATCH V7 4/4] edminiv2: add mvsata_ide and cmd_ide support

[Prafulla Wadaskar]

> -----Original Message-----
> From: u-boot-bounces at lists.denx.de 
> [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
> Sent: Thursday, August 05, 2010 6:06 PM
> To: u-boot at lists.denx.de
> Subject: [U-Boot] [PATCH V7 4/4] edminiv2: add mvsata_ide and 
> cmd_ide support
> 
> Add mvsata_ide and cmd_ide configuration in edminiv2 config
> 
> Signed-off-by: Albert Aribaud <albert.aribaud at free.fr>
> ---
>  include/configs/edminiv2.h |   34 +++++++++++++++++++++++++++++++++-
>  1 files changed, 33 insertions(+), 1 deletions(-)
> 
> diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h
> index 055931c..57dd165 100644
> --- a/include/configs/edminiv2.h
> +++ b/include/configs/edminiv2.h
> @@ -60,7 +60,7 @@
>  
>  #define ORION5X_MPP0_7		0x00000003
>  #define ORION5X_MPP8_15		0x55550000
> -#define ORION5X_MPP16_23	0x00000000
> +#define ORION5X_MPP16_23	0x00005555
>  
>  /*
>   * Board-specific values for Orion5x GPIO low level init:
> @@ -131,6 +131,7 @@
>   * Commands configuration - using default command set for now
>   */
>  #include <config_cmd_default.h>
> +#define CONFIG_CMD_IDE
>  
>  /*
>   * Network
> @@ -150,6 +151,37 @@
>  #endif
>  
>  /*
> + * IDE
> + */
> +#ifdef CONFIG_CMD_IDE
> +#define __io
> +#define CONFIG_IDE_PREINIT
> +#define CONFIG_DOS_PARTITION
> +#define CONFIG_CMD_EXT2
> +/* ED Mini V has an IDE-compatible SATA connector for port 1 */
> +#define CONFIG_MVSATA_IDE
> +#define CONFIG_MVSATA_IDE_USE_PORT1
> +/* Needs byte-swapping for ATA data register */
> +#define CONFIG_IDE_SWAP_IO
> +/* Data, registers and alternate blocks are at the same offset */
> +#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
> +#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
> +#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
> +/* Each 8-bit ATA register is aligned to a 4-bytes address */
> +#define CONFIG_SYS_ATA_STRIDE		4
> +/* Controller supports 48-bits LBA addressing */
> +#define CONFIG_LBA48
> +/* A single bus, a single device */
> +#define CONFIG_SYS_IDE_MAXBUS		1
> +#define CONFIG_SYS_IDE_MAXDEVICE	1
> +/* ATA registers base is at SATA controller base */
> +#define CONFIG_SYS_ATA_BASE_ADDR	ORION5X_SATA_BASE
> +/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
> +#define CONFIG_SYS_ATA_IDE0_OFFSET	ORION5X_SATA_PORT1_OFFSET
> +/* end of IDE defines */
> +#endif /* CMD_IDE */
> +
> +/*
>   *  Environment variables configurations
>   */
>  #define CONFIG_ENV_IS_IN_FLASH		1
> -- 

Acked-by: Prafulla Wadaskar <prafulla at marvell.com>

Regards..
Prafulla . .