[U-Boot] [RFC][PATCH 3/3] Add board support for the eXMeritus HWW-1U-1A devices
Kyle Moffett
Kyle.D.Moffett at boeing.com
Fri Aug 13 18:28:00 CEST 2010
The eXMeritus HWW-1U-1A unit is a DO-160-certified 13lb 1U chassis
with 3 independent TEMPEST zones. Two independent P2020 computers may
be found inside each zone. Complete hardware support is included.
High-level hardware overview:
* DO-160 certified for passenger aircraft (noncritical)
* TEMPEST ceritified for RED/BLACK separation
* 3 zones per chassis, 2 computers per zone (total of 6)
* Dual-core 1.066GHz P2020 per computer
* One 2GB DDR2 SO-RDIMM module per computer (upgradable to 4GB)
* Removable 80GB or 160GB Intel X18-M SSD per computer
* Front-accessible dual-port E1000E per computer
* Front-accessible serial console per computer
* Front-accessible USB port per computer
* Internal Gigabit crossover within each TEMPEST zone
* Internal unidirectional fiber links across TEMPEST zones
* Battery-backed DS1339 I2C RTC on each CPU.
Combined, each 13lb 1U chassis contains 12GB RAM, 12 cores @ 1.066GHz,
12 front-accessible Gigabit Ethernet ports and 960GB of solid-state
storage with a total power consumption of ~200W.
Additional notes:
* SPD detection is only known to work with the DO-160-certified DIMMs
* A U-Boot built with 36-bit address-space seems to work, but I don't
yet have a usable 36-bit kernel or DTB, so it's mostly untested.
* CPU reset is a little quirky due to hardware misfeature, see the
extensive comments in the board_reset_r() function in hww-1u-1a.c
Signed-off-by: Kyle Moffett <Kyle.D.Moffett at boeing.com>
---
MAKEALL | 2 +
Makefile | 4 +
board/exmeritus/hww-1u-1a/Makefile | 54 +++
board/exmeritus/hww-1u-1a/config.mk | 31 ++
board/exmeritus/hww-1u-1a/ddr.c | 136 +++++++
board/exmeritus/hww-1u-1a/gpios.h | 131 ++++++
board/exmeritus/hww-1u-1a/hww-1u-1a.c | 697 +++++++++++++++++++++++++++++++++
board/exmeritus/hww-1u-1a/law.c | 40 ++
board/exmeritus/hww-1u-1a/tlb.c | 93 +++++
cpu/mpc85xx/cpu.c | 7 +-
include/configs/HWW_1U_1A.h | 478 ++++++++++++++++++++++
11 files changed, 1671 insertions(+), 2 deletions(-)
create mode 100644 board/exmeritus/hww-1u-1a/Makefile
create mode 100644 board/exmeritus/hww-1u-1a/config.mk
create mode 100644 board/exmeritus/hww-1u-1a/ddr.c
create mode 100644 board/exmeritus/hww-1u-1a/gpios.h
create mode 100644 board/exmeritus/hww-1u-1a/hww-1u-1a.c
create mode 100644 board/exmeritus/hww-1u-1a/law.c
create mode 100644 board/exmeritus/hww-1u-1a/tlb.c
create mode 100644 include/configs/HWW_1U_1A.h
diff --git a/MAKEALL b/MAKEALL
index 5c303f9..bd1a3de 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -387,6 +387,8 @@ LIST_83xx=" \
LIST_85xx=" \
ATUM8548 \
+ HWW-1U-1A \
+ HWW-1U-1A_36BIT \
MPC8536DS \
MPC8536DS_NAND \
MPC8536DS_SDCARD \
diff --git a/Makefile b/Makefile
index e141cb2..ad14913 100644
--- a/Makefile
+++ b/Makefile
@@ -2499,6 +2499,10 @@ P2020DS_36BIT_config \
P2020DS_config: unconfig
@$(MKCONFIG) -t $(@:_config=) P2020DS ppc mpc85xx p2020ds freescale
+HWW_1U_1A_36BIT_config \
+HWW_1U_1A_config: unconfig
+ @$(MKCONFIG) -t $(@:_config=) HWW_1U_1A ppc mpc85xx hww-1u-1a exmeritus
+
P1011RDB_config \
P1011RDB_NAND_config \
P1011RDB_SDCARD_config \
diff --git a/board/exmeritus/hww-1u-1a/Makefile b/board/exmeritus/hww-1u-1a/Makefile
new file mode 100644
index 0000000..caa6a69
--- /dev/null
+++ b/board/exmeritus/hww-1u-1a/Makefile
@@ -0,0 +1,54 @@
+#
+# Copyright 2007-2009 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS-y += $(BOARD).o
+COBJS-y += law.o
+COBJS-y += tlb.o
+COBJS-$(CONFIG_DDR_SPD) += ddr.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/exmeritus/hww-1u-1a/config.mk b/board/exmeritus/hww-1u-1a/config.mk
new file mode 100644
index 0000000..878b7b3
--- /dev/null
+++ b/board/exmeritus/hww-1u-1a/config.mk
@@ -0,0 +1,31 @@
+#
+# Copyright 2009-2010 eXMeritus, A Boeing Company
+# Copyright 2007-2009 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# p2020ds board
+#
+ifndef TEXT_BASE
+TEXT_BASE = 0xeff80000
+endif
+
+RESET_VECTOR_ADDRESS = 0xeffffffc
diff --git a/board/exmeritus/hww-1u-1a/ddr.c b/board/exmeritus/hww-1u-1a/ddr.c
new file mode 100644
index 0000000..b587c87
--- /dev/null
+++ b/board/exmeritus/hww-1u-1a/ddr.c
@@ -0,0 +1,117 @@
+/*
+ * Copyright 2009-2010 eXMeritus, A Boeing Company
+ * Copyright 2008-2009 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+static void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+ i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+ return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+ unsigned int ctrl_num)
+{
+ unsigned int i;
+ unsigned int i2c_address = 0;
+
+ for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+ if (ctrl_num == 0 && i == 0)
+ i2c_address = SPD_EEPROM_ADDRESS1;
+ get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+ }
+}
+
+typedef struct {
+ u32 datarate_mhz_low;
+ u32 datarate_mhz_high;
+ u32 n_ranks;
+ u32 clk_adjust;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2T;
+} board_specific_parameters_t;
+
+/* ranges for parameters:
+ * wr_data_delay = 0-6
+ * clk adjust = 0-8
+ * cpo 2-0x1E (30)
+ */
+
+const board_specific_parameters_t board_specific_parameters[][20] = {
+ {
+ /* memory controller 0 */
+ /* lo| hi| num| clk| cpo|wrdata|2T */
+ /* mhz| mhz|ranks|adjst| | delay| */
+ { 0,1000, 2, 4, 4, 2, 0},
+ { 0,1000, 1, 4, 4, 2, 0},
+ },
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const board_specific_parameters_t *pbsp =
+ &(board_specific_parameters[ctrl_num][0]);
+ u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
+ sizeof(board_specific_parameters[0][0]);
+ u32 i;
+ ulong ddr_freq;
+
+ /* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
+ * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
+ * there are two dimms in the controller, set odt_rd_cfg to 3 and
+ * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
+ */
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ if (i&1) { /* odd CS */
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 0;
+ } else { /* even CS */
+ if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 4;
+ } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
+ popts->cs_local_opts[i].odt_rd_cfg = 3;
+ popts->cs_local_opts[i].odt_wr_cfg = 3;
+ }
+ }
+ }
+
+ /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ for (i = 0; i < num_params; i++) {
+ if (ddr_freq >= pbsp->datarate_mhz_low &&
+ ddr_freq <= pbsp->datarate_mhz_high &&
+ pdimm->n_ranks == pbsp->n_ranks) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay = pbsp->write_data_delay;
+ popts->twoT_en = pbsp->force_2T;
+ }
+ pbsp++;
+ }
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+}
diff --git a/board/exmeritus/hww-1u-1a/gpios.h b/board/exmeritus/hww-1u-1a/gpios.h
new file mode 100644
index 0000000..5b382a3
--- /dev/null
+++ b/board/exmeritus/hww-1u-1a/gpios.h
@@ -0,0 +1,131 @@
+/*
+ * Copyright 2010 eXMeritus, A Boeing Company
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* Common CPU A/B GPIOs (GPIO8-GPIO15 and IRQ4-IRQ6) */
+#define GPIO_CPU_ID (1UL << (31 - 8))
+#define GPIO_BLUE_LED (1UL << (31 - 9))
+#define GPIO_DIMM_RESET (1UL << (31 - 10))
+#define GPIO_USB_RESET (1UL << (31 - 11))
+#define GPIO_UNUSED_12 (1UL << (31 - 12))
+#define GPIO_GETH0_RESET (1UL << (31 - 13))
+#define GPIO_RS422_RE (1UL << (31 - 14))
+#define GPIO_RS422_DE (1UL << (31 - 15))
+#define IRQ_I2CINT (1UL << (31 - 20))
+#define IRQ_FANINT (1UL << (31 - 21))
+#define IRQ_DIMM_EVENT (1UL << (31 - 22))
+
+/* CPU A GPIOS (GPIO0-GPIO7 and IRQ0-IRQ3) */
+#define GPIO_CPUA_UNUSED_0 (1UL << (31 - 0))
+#define GPIO_CPUA_CPU_READY (1UL << (31 - 1))
+#define GPIO_CPUA_DEBUG_LED2 (1UL << (31 - 2))
+#define GPIO_CPUA_DEBUG_LED1 (1UL << (31 - 3))
+#define GPIO_CPUA_TDIS2B (1UL << (31 - 4)) /* MAC 2 TX B */
+#define GPIO_CPUA_TDIS2A (1UL << (31 - 5)) /* MAC 2 TX A */
+#define GPIO_CPUA_TDIS1B (1UL << (31 - 6)) /* MAC 1 TX B */
+#define GPIO_CPUA_TDIS1A (1UL << (31 - 7)) /* MAC 1 TX A */
+#define IRQ_CPUA_UNUSED_0 (1UL << (31 - 16))
+#define IRQ_CPUA_UNUSED_1 (1UL << (31 - 17))
+#define IRQ_CPUA_UNUSED_2 (1UL << (31 - 18))
+#define IRQ_CPUA_UNUSED_3 (1UL << (31 - 19))
+
+/* CPU B GPIOS (GPIO0-GPIO7 and IRQ0-IRQ3) */
+#define GPIO_CPUB_RMUX_SEL1B (1UL << (31 - 0))
+#define GPIO_CPUB_RMUX_SEL0B (1UL << (31 - 1))
+#define GPIO_CPUB_RMUX_SEL1A (1UL << (31 - 2))
+#define GPIO_CPUB_RMUX_SEL0A (1UL << (31 - 3))
+#define GPIO_CPUB_UNUSED_4 (1UL << (31 - 4))
+#define GPIO_CPUB_CPU_READY (1UL << (31 - 5))
+#define GPIO_CPUB_DEBUG_LED2 (1UL << (31 - 6))
+#define GPIO_CPUB_DEBUG_LED1 (1UL << (31 - 7))
+#define IRQ_CPUB_SD_1A (1UL << (31 - 16))
+#define IRQ_CPUB_SD_2B (1UL << (31 - 17))
+#define IRQ_CPUB_SD_2A (1UL << (31 - 18))
+#define IRQ_CPUB_SD_1B (1UL << (31 - 19))
+
+#define GPIOIRQ_CPUB_INIT_DIR /* Output pins */ \
+ ( GPIOIRQ_GLBL_INIT_DIR | GPIO_CPUB_CPU_READY \
+ | GPIO_CPUB_DEBUG_LED2 | GPIO_CPUB_DEBUG_LED1 \
+ | GPIO_CPUB_RMUX_SEL0A | GPIO_CPUB_RMUX_SEL0B \
+ | GPIO_CPUB_RMUX_SEL1A | GPIO_CPUB_RMUX_SEL1B )
+
+#define GPIOIRQ_CPUB_INIT_VAL /* Pins to drive high */ \
+ ( GPIOIRQ_GLBL_INIT_VAL | GPIO_CPUB_CPU_READY \
+ | GPIO_CPUB_RMUX_SEL0A | GPIO_CPUB_RMUX_SEL0B )
+
+#define GPIOIRQ_CPUB_BOOT_VAL /* Pins to drive high */ \
+ ( GPIOIRQ_GLBL_BOOT_VAL | GPIO_CPUB_CPU_READY \
+ | GPIO_CPUB_RMUX_SEL0A | GPIO_CPUB_RMUX_SEL0B )
+
+static inline void hww1u1a_gpio_set(unsigned int mask,
+ unsigned int dir, unsigned int val)
+{
+ volatile ccsr_gpio_t *gpio;
+
+ /* First mask off the unwanted parts of "dir" and "val" */
+ dir &= mask;
+ val &= mask;
+
+ /* Now read in the values we're supposed to preserve */
+ gpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR + 0xc00);
+ dir |= (in_be32(&gpio->gpdir) & ~mask);
+ val |= (in_be32(&gpio->gpdat) & ~mask);
+
+ /* Now write out the new values, writing the direction first */
+ out_be32(&gpio->gpdir, dir);
+ asm("sync; isync":::"memory");
+ out_be32(&gpio->gpdat, val);
+}
+
+static inline void hww1u1a_gpio_set_in(unsigned int gpios)
+{
+ hww1u1a_gpio_set(gpios, 0x00000000, 0x00000000);
+}
+
+static inline void hww1u1a_gpio_set_low(unsigned int gpios)
+{
+ hww1u1a_gpio_set(gpios, 0xFFFFFFFF, 0x00000000);
+}
+
+static inline void hww1u1a_gpio_set_high(unsigned int gpios)
+{
+ hww1u1a_gpio_set(gpios, 0xFFFFFFFF, 0xFFFFFFFF);
+}
+
+static inline unsigned int hww1u1a_gpio_get(unsigned int mask)
+{
+ volatile ccsr_gpio_t *gpio;
+ unsigned int ret;
+
+ /* Read the requested values */
+ gpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR + 0xc00);
+ ret = mask & in_be32(&gpio->gpdat);
+
+ return ret;
+}
+
+static inline unsigned int hww1u1a_is_cpu_a(void)
+{
+ return !hww1u1a_gpio_get(GPIO_CPU_ID);
+}
+
+static inline unsigned int hww1u1a_is_cpu_b(void)
+{
+ return !!hww1u1a_gpio_get(GPIO_CPU_ID);
+}
+
diff --git a/board/exmeritus/hww-1u-1a/hww-1u-1a.c b/board/exmeritus/hww-1u-1a/hww-1u-1a.c
new file mode 100644
index 0000000..9671549
--- /dev/null
+++ b/board/exmeritus/hww-1u-1a/hww-1u-1a.c
@@ -0,0 +1,697 @@
+/*
+ * Copyright 2009-2010 eXMeritus, A Boeing Company
+ * Copyright 2007-2009 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <tsec.h>
+#include <asm/fsl_law.h>
+#include <asm/mp.h>
+#include <netdev.h>
+#include <malloc.h>
+#include <i2c.h>
+
+#include "gpios.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t fixed_sdram(void);
+
+int checkboard(void)
+{
+ volatile ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR;
+
+ unsigned int gpio_high = 0;
+ unsigned int gpio_low = 0;
+ unsigned int gpio_in = 0;
+ unsigned int i;
+
+ puts("Board: HWW-1U-1A ");
+#ifdef CONFIG_PHYS_64BIT
+ puts("(36-bit addrmap) ");
+#endif
+
+ /*
+ * First just figure out which CPU we're on, then use that to
+ * configure the lists of other GPIOs to be programmed.
+ */
+ hww1u1a_gpio_set_in(GPIO_CPU_ID);
+ if (hww1u1a_is_cpu_a()) {
+ puts("CPU A\n");
+
+ /* We want to turn on some LEDs */
+ gpio_high |= GPIO_CPUA_CPU_READY;
+ gpio_low |= GPIO_CPUA_DEBUG_LED1;
+ gpio_low |= GPIO_CPUA_DEBUG_LED2;
+
+ /* Disable the unused transmitters */
+ gpio_low |= GPIO_CPUA_TDIS1A;
+ gpio_high |= GPIO_CPUA_TDIS1B;
+ gpio_low |= GPIO_CPUA_TDIS2A;
+ gpio_high |= GPIO_CPUA_TDIS2B;
+ } else {
+ puts("CPU B\n");
+
+ /* We want to turn on some LEDs */
+ gpio_high |= GPIO_CPUB_CPU_READY;
+ gpio_low |= GPIO_CPUB_DEBUG_LED1;
+ gpio_low |= GPIO_CPUB_DEBUG_LED2;
+
+ /* Enable the appropriate receivers */
+ gpio_high |= GPIO_CPUB_RMUX_SEL0A;
+ gpio_high |= GPIO_CPUB_RMUX_SEL0B;
+ gpio_low |= GPIO_CPUB_RMUX_SEL1A;
+ gpio_low |= GPIO_CPUB_RMUX_SEL1B;
+ }
+
+ /* These GPIOs are common */
+ gpio_in |= IRQ_I2CINT | IRQ_FANINT | IRQ_DIMM_EVENT;
+ gpio_low |= GPIO_RS422_RE;
+ gpio_high |= GPIO_RS422_DE;
+
+ /* Ok, now go ahead and program all of those in one go */
+ hww1u1a_gpio_set( gpio_high|gpio_low|gpio_in,
+ gpio_high|gpio_low,
+ gpio_high);
+
+ /*
+ * If things have been taken out of reset early (for example, by one
+ * of the BDI3000 debuggers), then we need to put them back in reset
+ * and delay a while before we continue.
+ */
+#define GPIO_RESETS (GPIO_DIMM_RESET|GPIO_USB_RESET|GPIO_GETH0_RESET)
+ if (hww1u1a_gpio_get(GPIO_RESETS)) {
+ puts("Debugger detected... extra device reset enabled!\n");
+
+ /* Put stuff into reset and disable the DDR controller */
+ hww1u1a_gpio_set_low(GPIO_RESETS);
+ out_be32(&ddr->sdram_cfg, 0x00000000);
+
+ puts(" Waiting 1 sec for reset...");
+ for (i = 0; i < 10; i++) {
+ udelay(100000);
+ puts(".");
+ }
+ puts("\n");
+ }
+
+ /* Now bring everything back out of reset again */
+ hww1u1a_gpio_set_high(GPIO_RESETS);
+ return 0;
+}
+
+/* Create a prompt-like string: "uboot at HOSTNAME% " */
+#define PROMPT_PREFIX "uboot at exm"
+#define PROMPT_SUFFIX "% "
+
+/* This function returns a PS1 prompt based on the serial number */
+static char *hww1u1a_prompt = NULL;
+const char *hww1u1a_get_ps1(void)
+{
+ unsigned long len, i, j;
+ const char *serialnr;
+
+ /* If our prompt was already set, just use that */
+ if (hww1u1a_prompt)
+ return hww1u1a_prompt;
+
+ /* Use our serial number if present, otherwise "UNPROGRAMMED-[AB]" */
+ serialnr = getenv("serial#");
+ if (!serialnr || !serialnr[0]) {
+ if (hww1u1a_is_cpu_a())
+ serialnr = "999999-XA";
+ else
+ serialnr = "999999-XB";
+ }
+
+ /*
+ * We will turn the serial number into a hostname by:
+ * (A) Delete all non-alphanumerics.
+ * (B) Lowercase all letters
+ * (C) Prefix "exm"
+ */
+ for (i = 0, len = 0; serialnr[i]; i++) {
+ if ('0' <= serialnr[i] && serialnr[i] <= '9')
+ len++;
+ else if ('a' <= serialnr[i] && serialnr[i] <= 'z')
+ len++;
+ else if ('A' <= serialnr[i] && serialnr[i] <= 'Z')
+ len++;
+ }
+
+ len += sizeof(PROMPT_PREFIX PROMPT_SUFFIX); /* Includes NUL */
+ hww1u1a_prompt = malloc(len);
+ if (!hww1u1a_prompt)
+ return PROMPT_PREFIX "UNKNOWN(ENOMEM)" PROMPT_SUFFIX;
+
+ /* Now actually fill it in */
+ i = 0;
+
+ /* Handle the prefix */
+ for (j = 0; j < sizeof(PROMPT_PREFIX) - 1; j++)
+ hww1u1a_prompt[i++] = PROMPT_PREFIX[j];
+
+ /* Now the serial# part of the hostname */
+ for (j = 0; serialnr[j]; j++) {
+ if ('0' <= serialnr[j] && serialnr[j] <= '9')
+ hww1u1a_prompt[i++] = serialnr[j];
+ else if ('a' <= serialnr[j] && serialnr[j] <= 'z')
+ hww1u1a_prompt[i++] = serialnr[j];
+ else if ('A' <= serialnr[j] && serialnr[j] <= 'Z')
+ hww1u1a_prompt[i++] = serialnr[j] + 'a' - 'A';
+ }
+
+ /* Finally the suffix */
+ for (j = 0; j < sizeof(PROMPT_SUFFIX); j++)
+ hww1u1a_prompt[i++] = PROMPT_SUFFIX[j];
+
+ /* This should all have added up, but just in case */
+ hww1u1a_prompt[len - 1] = '\0';
+
+ /* Now we're done */
+ return hww1u1a_prompt;
+}
+
+
+phys_size_t initdram(int board_type)
+{
+#ifndef CONFIG_SPD_EEPROM
+ /* This is manual (non-SPD) DDR2 SDRAM configuration (2GB ECC) */
+ volatile ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR;
+ phys_size_t dram_size = (2048ULL) << 20;
+ out_be32(&ddr->cs0_bnds, 0x0000003F);
+ out_be32(&ddr->cs1_bnds, 0x0040007F);
+ out_be32(&ddr->cs0_config, 0x80014202);
+ out_be32(&ddr->cs1_config, 0x80014202);
+ out_be32(&ddr->timing_cfg_0, 0x00330804);
+ out_be32(&ddr->timing_cfg_1, 0x6f69f643);
+ out_be32(&ddr->timing_cfg_2, 0x022068cd);
+ out_be32(&ddr->timing_cfg_3, 0x00030000);
+ out_be32(&ddr->sdram_cfg_2, 0x04400010);
+ out_be32(&ddr->sdram_mode, 0x00440452);
+ out_be32(&ddr->sdram_mode_2, 0x00000000);
+ out_be32(&ddr->sdram_md_cntl, 0x00000000);
+ out_be32(&ddr->sdram_interval, 0x0a280110);
+ out_be32(&ddr->sdram_data_init, 0xDEADBEEF);
+ out_be32(&ddr->sdram_clk_cntl, 0x02000000);
+ out_be32(&ddr->timing_cfg_4, 0x00000000);
+ out_be32(&ddr->timing_cfg_5, 0x00000000);
+ out_be32(&ddr->ddr_zq_cntl, 0x00000000);
+ out_be32(&ddr->ddr_wrlvl_cntl, 0x00000000);
+ out_be32(&ddr->ip_rev1, 0x00020403);
+ out_be32(&ddr->ip_rev2, 0x00000100);
+ out_be32(&ddr->err_int_en, 0x0000000D);
+ out_be32(&ddr->err_disable, 0x00000000);
+ out_be32(&ddr->err_sbe, 0x00010000);
+ out_be32(&ddr->ddr_cdr1, 0x00040000);
+ out_be32(&ddr->ddr_cdr2, 0x00000000);
+ out_be32(&ddr->sdram_cfg, 0x73000000);
+
+ /* Allow time for the clocks to stabilize before enabling */
+ udelay(500);
+ out_be32(&ddr->sdram_cfg, 0xF3000000);
+
+ /* Now wait until memory is initialized */
+ while (in_be32(&ddr->sdram_cfg_2) & 0x00000010)
+ udelay(1000);
+
+ /* Finally we set up the local access windows */
+ if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, dram_size,
+ LAW_TRGT_IF_DDR) < 0) {
+ printf("ERROR setting Local Access Windows for DDR\n");
+ return 0;
+ };
+#else
+ /* We also support "Automagic mode" */
+ phys_size_t dram_size = fsl_ddr_sdram();
+#endif
+
+ /* Before we're done we need to set up the TLB entries */
+ return setup_ddr_tlbs(dram_size >> 20) << 20;
+}
+
+static struct pci_controller pcie1_hose;
+static struct pci_controller pcie2_hose;
+static struct pci_controller pcie3_hose;
+void pci_init_board(void)
+{
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ struct fsl_pci_info pci_info[3];
+ u32 devdisr, pordevsr, io_sel;
+ int first_free_busno = 0;
+ int num = 0;
+
+ int pcie_ep, pcie_configured;
+
+ devdisr = in_be32(&gur->devdisr);
+ pordevsr = in_be32(&gur->pordevsr);
+ io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
+
+ debug(" pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel);
+
+ if (!(pordevsr & MPC85xx_PORDEVSR_SGMII2_DIS))
+ printf(" eTSEC2 is in sgmii mode.\n");
+ if (!(pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS))
+ printf(" eTSEC3 is in sgmii mode.\n");
+
+ puts("\n");
+ pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_1, io_sel);
+
+ if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)) {
+ SET_STD_PCIE_INFO(pci_info[num], 1);
+ pcie_ep = fsl_setup_hose(&pcie1_hose, pci_info[num].regs);
+ printf(" PCIE1 connected as %s (base addr %lx)\n",
+ pcie_ep ? "Endpoint" : "Root Complex",
+ pci_info[num].regs);
+ first_free_busno = fsl_pci_init_port(&pci_info[num++],
+ &pcie1_hose, first_free_busno);
+ } else {
+ printf(" PCIE1: disabled\n");
+ }
+
+ puts("\n");
+ pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_2, io_sel);
+
+ if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE2)) {
+ SET_STD_PCIE_INFO(pci_info[num], 2);
+ pcie_ep = fsl_setup_hose(&pcie2_hose, pci_info[num].regs);
+ printf(" PCIE2 connected as %s (base addr %lx)\n",
+ pcie_ep ? "Endpoint" : "Root Complex",
+ pci_info[num].regs);
+ first_free_busno = fsl_pci_init_port(&pci_info[num++],
+ &pcie2_hose, first_free_busno);
+ } else {
+ printf(" PCIE2: disabled\n");
+ }
+
+ puts("\n");
+ pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_3, io_sel);
+
+ if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE3)) {
+ SET_STD_PCIE_INFO(pci_info[num], 3);
+ pcie_ep = fsl_setup_hose(&pcie3_hose, pci_info[num].regs);
+ printf(" PCIE3 connected as %s (base addr %lx)\n",
+ pcie_ep ? "Endpoint" : "Root Complex",
+ pci_info[num].regs);
+ first_free_busno = fsl_pci_init_port(&pci_info[num++],
+ &pcie3_hose, first_free_busno);
+ } else {
+ printf(" PCIE3: disabled\n");
+ }
+ puts("\n");
+
+}
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap bootflash region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for FLASH */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ struct tsec_info_struct tsec_info[4];
+ volatile ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR + 0xc00);
+
+ SET_STD_TSEC_INFO(tsec_info[0], 1);
+ SET_STD_TSEC_INFO(tsec_info[1], 2);
+ SET_STD_TSEC_INFO(tsec_info[2], 3);
+ if (pgpio->gpdat & GPIO_CPU_ID)
+ tsec_info[2].phyaddr = TSEC3_PHY_ADDR_CPUB;
+ else
+ tsec_info[2].phyaddr = TSEC3_PHY_ADDR_CPUA;
+
+ tsec_eth_init(bis, tsec_info, 3);
+ return pci_eth_init(bis);
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+ ft_fsl_pci_setup(blob, "pci0", &pcie3_hose);
+ ft_fsl_pci_setup(blob, "pci1", &pcie2_hose);
+ ft_fsl_pci_setup(blob, "pci2", &pcie1_hose);
+}
+
+void board_lmb_reserve(struct lmb *lmb)
+{
+ cpu_mp_lmb_reserve(lmb);
+}
+
+/* We don't have any really usable POST memory, so just fake it */
+unsigned long post_word_load (void)
+{
+ return 0l;
+}
+
+void post_word_store (unsigned long val)
+{
+ return;
+}
+
+/*
+ * Unfortunately we have a bit of a problem with our reset line wiring on the
+ * HWW-1U-1A boards.
+ *
+ * Specifically the "CPU A" reset controls all of the PCI devices on the
+ * IO/backplane card, which means ethernet and SATA controllers for both
+ * CPU A *and* CPU B.
+ *
+ * This is somewhat of a problem if the CPUs are reset independently... CPU B
+ * might fail to come up because his PCI devices are confused, or CPU B might
+ * die because CPU A just reset the SATA controller for his root filesystem.
+ *
+ * Since in practice the CPUs never need to reboot independently we will go
+ * ahead and require GPIO cross-communication between them before either one
+ * will reset.
+ *
+ * The communication protocol uses GPIOs 4-7 on the PCA9554 GPIO expander
+ * found on I2C-2 at address 0x3f. CPU A uses 4,5 as TX and 6,7 as RX; for
+ * CPU B we use the exact opposite.
+ *
+ * The GPIOs initialize as inputs during poweron, and are pulled high; the
+ * PCA9554 expanders will maintain valid outputs over soft-reset allowing for
+ * reliable operation.
+ *
+ * To avoid duplication, we will assign names to the GPIOs:
+ * ,---------------------------------------.
+ * | GPIO4 | GPIO5 | GPIO6 | GPIO7 |
+ * ,---------|=========|=========|=========|=========|
+ * | CPU A | tx1 | tx2 | rx1 | rx2 |
+ * |---------|---------|---------|---------|---------|
+ * | CPU B | rx1 | rx2 | tx1 | tx2 |
+ * `-------------------------------------------------'
+ *
+ * The state machine for each CPU is below. In simplistic terms, each CPU
+ * waits until the other has cleared its GPIOs, then cause a tx1 high=>low
+ * transition. Upon seeing the other CPU do the same, it will perform a
+ * tx2 high=>low transition and again wait.
+ *
+ * Once both CPUs have performed and seen both transitions, they will each
+ * set tx1 high (to create an "invalid" state) and then reset.
+ *
+ * ,--------------.
+ * | START/ERROR: |<==-.
+ * ,-==>| tx2 = 1; | || (rx2 == 0)
+ * || | tx1 = 1; | ==-'
+ * || `--------------'
+ * || ||
+ * || || (rx2 == 1)
+ * || \/
+ * || ,--------------.
+ * || | WAITING: |<==-.
+ * |\== | tx1 = 0; | || (rx1 == 1) && (rx2 == 1)
+ * || | | ==-'
+ * || `--------------'
+ * || ||
+ * || || (rx1 == 0) && (rx2 == 1)
+ * || \/
+ * || ,--------------.
+ * || | BOTH_READY: |<==-.
+ * `-== | tx2 = 0; | || (rx1 == 0) && (rx2 == 1)
+ * | | ==-'
+ * `--------------'
+ * ||
+ * || (rx2 == 0)
+ * \/
+ * ,--------------.
+ * | RESETTING: |
+ * | tx1 = 1; |
+ * | reset(); |
+ * `--------------'
+ *
+ * While in the "BOTH_READY" state a high-to-low rx2 transition must be
+ * followed within 50ms by activation of the HRESET_REQ signal. That
+ * state MUST NOT be interrupted by any event other than the observed
+ * event (rx1 == high) && (rx2 == high).
+ */
+
+#define PCA9554_I2C_ADDR 0x3f
+static inline int pca9554_read(u8 reg)
+{
+ u8 value;
+ int ret;
+
+ i2c_set_bus_num(1);
+ ret = i2c_read(PCA9554_I2C_ADDR, reg, 1, &value, 1);
+ if (ret < 0)
+ return ret;
+ return value;
+}
+static inline int pca9554_write(u8 reg, u8 value)
+{
+ i2c_set_bus_num(1);
+ return i2c_write(PCA9554_I2C_ADDR, reg, 1, &value, 1);
+}
+static inline int pca9554_setmask(u8 reg, u8 value, u8 mask)
+{
+ int ret = pca9554_read(reg);
+ if (ret < 0)
+ return ret;
+
+ return pca9554_write(reg, (ret & ~mask) | (value & mask));
+}
+
+#define PCA9554_DATA_IN 0x00
+#define PCA9554_DATA_OUT 0x01
+#define PCA9554_INVERT 0x02
+#define PCA9554_IS_INPUT 0x03
+
+static inline int pca9554_set_low(u8 gpio)
+{
+ return pca9554_setmask(PCA9554_DATA_OUT, 0x00, (1U << gpio));
+}
+
+static inline int pca9554_set_high(u8 gpio)
+{
+ return pca9554_setmask(PCA9554_DATA_OUT, 0xff, (1U << gpio));
+}
+
+static inline int pca9554_set_output(u8 gpio)
+{
+ return pca9554_setmask(PCA9554_IS_INPUT, 0x00, (1U << gpio));
+}
+
+static inline int pca9554_set_input(u8 gpio)
+{
+ return pca9554_setmask(PCA9554_DATA_OUT, 0xff, (1U << gpio));
+}
+
+void board_reset_r(void)
+{
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u8 tx1, tx2, rx1, rx2, rxmask;
+ int ret;
+
+ /* Our state-machine state */
+ enum {
+ START_ERROR = 0,
+ WAITING,
+ BOTH_READY,
+ } state;
+
+ printf("RESET: Preparing...");
+
+ /* First clear the "INVERT" setting on all relevant GPIOs */
+ if (pca9554_setmask(PCA9554_INVERT, 0x00, 0xf0) < 0)
+ goto err;
+
+ /* Check what CPU we are and configure accordingly. */
+ if (hww1u1a_is_cpu_a()) {
+ tx1 = 4; tx2 = 5; rx1 = 6; rx2 = 7;
+ } else {
+ rx1 = 4; rx2 = 5; tx1 = 6; tx2 = 7;
+ }
+ rxmask = (1U << rx1) | (1U << rx2);
+
+ /* Configure both inputs */
+ if (pca9554_set_input(rx1) < 0)
+ goto err;
+ if (pca9554_set_input(rx2) < 0)
+ goto err;
+
+ /* Make sure the very first thing we do is set the "tx2" GPIO high */
+ if (pca9554_set_high(tx2) < 0)
+ goto err;
+ if (pca9554_set_output(tx2) < 0)
+ goto err;
+
+ /* Now reset our other transmit pin */
+ if (pca9554_set_high(tx1) < 0)
+ goto err;
+ if (pca9554_set_output(tx1) < 0)
+ goto err;
+
+ /* Enter the state machine */
+ state = START_ERROR;
+
+poll_state:
+ ret = pca9554_read(PCA9554_DATA_IN);
+ switch (state) {
+ case START_ERROR:
+ if (ctrlc())
+ goto intr;
+
+ if (ret < 0)
+ goto err;
+
+ /* Wait for (rx2 == high) */
+ if (ret & (1U << rx2)) {
+ /* Success! */
+ state = WAITING;
+ goto enter_state;
+ }
+
+ goto poll_state;
+
+ case WAITING:
+ if (ctrlc())
+ goto intr;
+
+ if (ret < 0)
+ goto err;
+
+ /* Wait for (rx1 == low) && (rx2 == high) */
+ ret &= rxmask;
+ if (ret == (1U << rx2)) {
+ /* Success! */
+ state = BOTH_READY;
+ goto enter_state;
+ }
+ if (ret != rxmask) {
+ /* Oops, error */
+ state = START_ERROR;
+ goto enter_state;
+ }
+
+ goto poll_state;
+
+ case BOTH_READY:
+ /*
+ * Non-interruptable wait for (rx2 == low), however if we
+ * see (rx1 == high) and (rx2 == high) we should go back
+ * to START_ERROR.
+ */
+ if (ret < 0)
+ goto poll_state;
+
+ ret &= rxmask;
+ if (ret == rxmask) {
+ /* Oops, error */
+ state = START_ERROR;
+ goto enter_state;
+ }
+ if (ret & (1U << rx2))
+ goto poll_state;
+
+ /* Success, we have to reset quick now! */
+ (void)pca9554_set_high(tx1);
+
+ /* Turn on the "HRESET_REQ" pin (hard-reset request) */
+ printf("\nRESET: Hardware reset triggered, waiting...\n");
+ out_be32(&gur->rstcr, 0x2);
+ while (1)
+ udelay(10000);
+ }
+
+enter_state:
+ switch (state) {
+ case START_ERROR:
+ printf("\nRESET: Negotiation error!");
+ printf("\nRESET: Starting over...");
+ /* Clear both GPIOs high in the right order */
+ if (pca9554_set_high(tx2) < 0)
+ goto err;
+ if (pca9554_set_high(tx1) < 0)
+ goto err;
+ if (ctrlc())
+ goto intr;
+
+ goto poll_state;
+
+ case WAITING:
+ printf("\nRESET: Waiting for peer...");
+ /* Set tx1 low */
+ if (pca9554_set_low(tx1) < 0)
+ goto err;
+ if (ctrlc())
+ goto intr;
+
+ goto poll_state;
+
+ case BOTH_READY:
+ printf("\nRESET: Both ready, point of no return...");
+ /* Point of no return: set tx2 low */
+ if (pca9554_set_low(tx2) < 0)
+ goto err;
+
+ goto poll_state;
+ }
+
+ /* We only get here through gotos */
+err:
+ printf("\nRESET: I2C communication error!\n");
+intr:
+ printf("\nRESET: Aborted!\n");
+ (void)pca9554_set_high(tx1);
+ (void)pca9554_set_high(tx2);
+ return;
+}
+
diff --git a/board/exmeritus/hww-1u-1a/law.c b/board/exmeritus/hww-1u-1a/law.c
new file mode 100644
index 0000000..c1dffd9
--- /dev/null
+++ b/board/exmeritus/hww-1u-1a/law.c
@@ -0,0 +1,40 @@
+/*
+ * Copyright 2008-2009 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+ SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCIE_1),
+ SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_1),
+ SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCIE_2),
+ SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_2),
+ SET_LAW(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCIE_3),
+ SET_LAW(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_3),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/exmeritus/hww-1u-1a/tlb.c b/board/exmeritus/hww-1u-1a/tlb.c
new file mode 100644
index 0000000..672e8b9
--- /dev/null
+++ b/board/exmeritus/hww-1u-1a/tlb.c
@@ -0,0 +1,93 @@
+/*
+ * Copyright 2009-2010 eXMeritus, A Boeing Company
+ * Copyright 2008-2009 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 0 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 0 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Boot page */
+ SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR,
+ CONFIG_BPTR_VIRT_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR,
+ CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_1M, 1),
+
+ /* W**G* - FLASH */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE,
+ CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI memory */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT,
+ CONFIG_SYS_PCIE3_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000,
+ CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000,
+ CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT,
+ CONFIG_SYS_PCIE3_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256K, 1),
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/cpu/mpc85xx/cpu.c b/cpu/mpc85xx/cpu.c
index 0cc6e03..49d963d 100644
--- a/cpu/mpc85xx/cpu.c
+++ b/cpu/mpc85xx/cpu.c
@@ -190,8 +190,10 @@ int checkcpu (void)
int do_reset (cmd_tbl_t *cmdtp, bd_t *bd, int flag, int argc, char *argv[])
{
-/* Everything after the first generation of PQ3 parts has RSTCR */
-#if defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
+#if defined(CONFIG_BOARD_RESET_R)
+ extern void board_reset_r(void);
+ board_reset_r();
+#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
defined(CONFIG_MPC8555) || defined(CONFIG_MPC8560)
unsigned long val, msr;
@@ -207,6 +209,7 @@ int do_reset (cmd_tbl_t *cmdtp, bd_t *bd, int flag, int argc, char *argv[])
val |= 0x70000000;
mtspr(DBCR0,val);
#else
+ /* Everything after the first generation of PQ3 parts has RSTCR */
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
out_be32(&gur->rstcr, 0x2); /* HRESET_REQ */
udelay(100);
diff --git a/include/configs/HWW_1U_1A.h b/include/configs/HWW_1U_1A.h
new file mode 100644
index 0000000..9c0706f
--- /dev/null
+++ b/include/configs/HWW_1U_1A.h
@@ -0,0 +1,478 @@
+/*
+ * Copyright 2009-2010 eXMeritus, A Boeing Company
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * HardwareWall HWW-1U-1A airborne unit configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/************************************************************************
+ * High-level system configuration options *
+ ************************************************************************/
+/*#define DEBUG 1*/
+#define CONFIG_BOOKE 1 /* Power/PowerPC Book-E */
+#define CONFIG_E500 1 /* e500 (Power ISA v2.03 with SPE) */
+#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 family */
+#define CONFIG_FSL_ELBC 1 /* FreeScale Enhanced LocalBus Cntlr */
+#define CONFIG_FSL_LAW 1 /* FreeScale Local Access Window */
+#define CONFIG_P2020 1 /* FreeScale P2020 */
+#define CONFIG_HWW1U1A 1 /* eXMeritus HardwareWall HWW-1U-1A */
+#define CONFIG_MP 1 /* Multiprocessing support */
+
+#define CONFIG_L2_CACHE 1 /* L2 cache enabled */
+#define CONFIG_BTB 1 /* Branch predition enabled */
+
+#define CONFIG_PANIC_HANG 1 /* No board reset on panic */
+#define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r() */
+#define CONFIG_BOARD_RESET_R 1 /* Call board_reset_r() */
+
+/* Allow the use of 36-bit physical addresses in "HWW_1U_1A_36BIT" mode */
+#define CONFIG_ENABLE_36BIT_PHYS 1
+#ifdef CONFIG_MK_36BIT
+# define CONFIG_PHYS_64BIT 1
+# define CONFIG_ADDR_MAP 1
+# define CONFIG_SYS_NUM_ADDR_MAP 16 /* Number of entries in TLB1 */
+#endif
+
+/* This is the U-Boot base address and size */
+#define CONFIG_SYS_MONITOR_BASE 0xeff80000
+#define CONFIG_SYS_MONITOR_LEN 0x00080000
+#if defined(TEXT_BASE) && (TEXT_BASE != CONFIG_SYS_MONITOR_BASE)
+# error "TEXT_BASE != CONFIG_SYS_MONITOR_BASE"
+#endif
+
+/* Reserve plenty of RAM for malloc (we have 2GB+) */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
+
+/* This is where we map our L2 cache so we can use it as RAM */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000
+#define CONFIG_SYS_INIT_RAM_END 0x00004000
+
+/* This is our temporary global data area just above the stack */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+
+/* The stack grows down from the global data area */
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/* Enable IRQs and watchdog with a 1000Hz system decrementer */
+#define CONFIG_CMD_IRQ
+#define CONFIG_SYS_HZ 1000
+#if 0 /* FIXME */
+#define CONFIG_WATCHDOG 1
+
+/* Enable Power-On-Self-Tests */
+#define CONFIG_POST 1
+#define CONFIG_CMD_DIAG
+#endif
+
+
+/************************************************************************
+ * Clock crystal configuration: *
+ * (1) SYS: 66.666MHz +/- 50ppm (drives CPU/PCI/DDR) *
+ * (2) CCB: Multiplier from SYS_CLK *
+ * (3) RTC: 25.000MHz +/- 50ppm (sampled against CCB clock) *
+ ************************************************************************/
+#undef CONFIG_CLOCKS_IN_MHZ
+#define CONFIG_SYS_CLK_FREQ 66666000/*Hz*/
+#define CONFIG_DDR_CLK_FREQ 66666000/*Hz*/
+
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000 0x7fff_ffff 2G DDR2 ECC SDRAM
+ * 0x8000_0000 0x9fff_ffff 512M PCI-E Bus 1
+ * 0xa000_0000 0xbfff_ffff 512M PCI-E Bus 2 (unused)
+ * 0xc000_0000 0xdfff_ffff 512M PCI-E Bus 3
+ * 0xe000_0000 0xe7ff_ffff 128M Spansion FLASH
+ * 0xe800_0000 0xefff_ffff 128M Spansion FLASH
+ * 0xffd0_0000 0xffd0_3fff 16K L1 boot stack (TLB0)
+ * 0xffe0_0000 0xffef_ffff 1M CCSR
+ * 0xffe0_5000 0xffe0_5fff 4K Enhanced LocalBus Controller
+ */
+
+/* Virtual Memory Map */
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
+#define CONFIG_SYS_FLASH_BASE 0xe0000000
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR @ reset */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
+#define CONFIG_SYS_CCSRBAR 0xffe00000 /* CCSRBAR @ runtime */
+
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+/* Physical Memory Map */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull
+#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull
+#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000ul
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000ul
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000ul
+#define CONFIG_SYS_FLASH_BASE_PHYS 0xe0000000ul
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000ul
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000ul
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000ul
+#define CONFIG_SYS_CCSRBAR_PHYS 0xffe00000ul
+#endif
+
+/* Legacy code needs this */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
+
+
+/************************************************************************
+ * U-Boot Environment Image: The two sectors immediately below U-Boot *
+ * form the U-Boot environment (regular and redundant) *
+ ************************************************************************/
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128kB (one flash sector) */
+#define CONFIG_ENV_SIZE 0x02000 /* 8kB */
+#define CONFIG_ENV_SIZE_REDUND 0x02000 /* 8kB */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_OVERWRITE 1
+
+
+/************************************************************************
+ * Serial Console Configuration *
+ ************************************************************************/
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Echo back characters received during a serial download */
+#define CONFIG_LOADS_ECHO 1
+
+/* Allow a serial-download to temporarily change baud */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
+
+
+/************************************************************************
+ * PCI and PCI-Express Support *
+ * Memory space is mapped 1-1, but I/O space must start from 0. *
+ ************************************************************************/
+
+#define CONFIG_PCI 1 /* Enable PCI/PCIE */
+#define CONFIG_PCI_PNP 1 /* Scan PCI busses */
+#define CONFIG_CMD_PCI /* Enable the "pci" command */
+#define CONFIG_FSL_PCI_INIT 1 /* Common FreeScale PCI initialization */
+#define CONFIG_FSL_PCIE_RESET 1 /* We have PCI-E reset errata */
+#define CONFIG_SYS_PCI_64BIT 1 /* PCI resources are 64-bit */
+#define CONFIG_PCI_SCAN_SHOW 1 /* Display PCI scan during boot */
+
+/* Enable all 3 PCI-E controllers */
+#define CONFIG_PCIE1 1
+#define CONFIG_PCIE2 1
+#define CONFIG_PCIE3 1
+
+/* PCI controller addresses */
+#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR+0x8000)
+#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000)
+#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
+
+/* PCI bus addresses */
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
+#endif
+
+
+/************************************************************************
+ * I2C Bus Support and devices *
+ ************************************************************************/
+
+/* Generic FreeScale hardware I2C support */
+#define CONFIG_HARD_I2C 1
+#define CONFIG_FSL_I2C 1
+#define CONFIG_CMD_I2C
+#define CONFIG_I2C_MULTI_BUS 1
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/* I2C bus configuration */
+#define CONFIG_SYS_I2C_SPEED 400000
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES { \
+ { 0, 0x29 } \
+}
+
+/* DDR2 SO-RDIMM SPD EEPROM is at I2C0-0x51 */
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS1 0x51
+#if 0
+#define CONFIG_CMD_EEPROM
+#endif
+
+/* DS1339 RTC is at I2C0-0x68 (I know it says "DS1337", it's a DS1339) */
+#define CONFIG_CMD_DATE
+#define CONFIG_RTC_DS1337
+#define CONFIG_SYS_RTC_BUS_NUM 0
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+/* Turn off RTC square-wave output to save battery */
+#define CONFIG_SYS_RTC_DS1337_NOOSC 1
+
+
+/************************************************************************
+ * FreeScale DDR2/3 SDRAM Controller *
+ ************************************************************************/
+#define CONFIG_FSL_DDR2 1 /* Our SDRAM slot is DDR2 */
+#define CONFIG_DDR_ECC 1 /* Enable ECC by default */
+#define CONFIG_DDR_SPD 1 /* Detect DDR config from SPD EEPROM */
+#define CONFIG_SPD_EEPROM 1 /* ...why 2 config variables for this? */
+#define CONFIG_VERY_BIG_RAM 1 /* Allow 2GB+ of RAM */
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_CMD_SDRAM
+
+/* Standard P2020 DDR controller parameters */
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+
+/* Make sure to tell the DDR controller to preinitialze all of RAM */
+#define CONFIG_MEM_INIT_VALUE 0xDEADBEEF
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 1
+
+/* Enable the U-Boot "memory test" */
+#define CONFIG_SYS_MEMTEST_START 0x00000000
+#define CONFIG_SYS_MEMTEST_END 0x7fffffff
+
+
+/************************************************************************
+ * FLASH Memory Configuration (2x 128MB SPANSION FLASH) *
+ ************************************************************************/
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
+
+/* Flash banks (2x 128MB) */
+#define FLASH0_PHYS (CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000ull)
+#define FLASH1_PHYS (CONFIG_SYS_FLASH_BASE_PHYS + 0x0000000ull)
+#define CONFIG_SYS_MAX_FLASH_BANKS 2
+#define CONFIG_SYS_MAX_FLASH_SECT 1024
+#define CONFIG_SYS_FLASH_BANKS_LIST { FLASH0_PHYS, FLASH1_PHYS }
+
+/* Flash configuration registers */
+#define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(FLASH0_PHYS) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(FLASH1_PHYS) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR0_PRELIM 0xf8000ff7
+#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7
+
+/* Flash timeouts (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000UL /* Erase (60s) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500UL /* Write (0.5s) */
+
+/* Quiet flash testing */
+#define CONFIG_SYS_FLASH_QUIET_TEST 1
+
+/* Don't bother checksumming the flash on boot */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+
+/* Make program/erase count down from 45/5 (9....8....7....) */
+#define CONFIG_FLASH_SHOW_PROGRESS 45
+
+#if 0
+# define CONFIG_CMD_JFFS2
+# define CONFIG_CMD_MTDPARTS
+#endif
+
+
+/************************************************************************
+ * Ethernet Device Support *
+ ************************************************************************/
+#define CONFIG_NET_MULTI 1 /* We have multiple devices */
+#define CONFIG_MII 1 /* Enable MII PHY code */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* ??? */
+#define CONFIG_PHY_GIGE 1 /* Support Gigabit PHYs */
+#define CONFIG_ETHPRIME "e1000#0" /* Default to external ports */
+
+#if 0
+/* All of the ethernet interfaces we should have */
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
+#define CONFIG_HAS_ETH4
+#endif
+
+/* Turn on various helpful networking commands */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+
+/* On-chip FreeScale P2020 "tsec" Ethernet (oneway fibers and peer) */
+#define CONFIG_TSEC_ENET 1
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC1_NAME "owt0"
+#define CONFIG_TSEC2_NAME "owt1"
+#define CONFIG_TSEC3_NAME "peer"
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC3_PHYIDX 0
+#define TSEC1_PHY_ADDR 2
+#define TSEC2_PHY_ADDR 3
+#define TSEC3_PHY_ADDR_CPUA 4
+#define TSEC3_PHY_ADDR_CPUB 5
+#define TSEC3_PHY_ADDR TSEC3_PHY_ADDR_CPUA
+
+/* PCI-E dual-port E1000 (external ethernet ports) */
+#define CONFIG_E1000 1
+#define CONFIG_E1000_FALLBACK_MAC { 0x00, 0x05, 0x93, 0x81, 0xff, 0xfe }
+
+
+/************************************************************************
+ * USB Thumbdrive Device Support *
+ ************************************************************************/
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_USB
+
+/* Partition and Filesystem support */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+
+
+/************************************************************************
+ * Command line configuration. *
+ ************************************************************************/
+#define CONFIG_CMDLINE_EDITING 1 /* Enable command editing */
+#define CONFIG_COMMAND_HISTORY 1 /* Enable command history */
+#define CONFIG_AUTOCOMPLETE 1 /* Enable command completion */
+#define CONFIG_SYS_LONGHELP 1 /* Enable detailed command help */
+#define CONFIG_SYS_MAXARGS 128 /* Up to 128 command-line args */
+#define CONFIG_SYS_PBSIZE 8192 /* Allow up to 8k printed lines */
+#define CONFIG_SYS_CBSIZE 4096 /* Allow up to 4k command lines */
+#define CONFIG_SYS_BARGSIZE 4096 /* Allow up to 4k boot args */
+#define CONFIG_SYS_HUSH_PARSER 1 /* Enable a fancier shell */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* Command-line continuation */
+
+/* A little extra magic here for the prompt */
+#define CONFIG_SYS_PROMPT hww1u1a_get_ps1()
+#ifndef __ASSEMBLY__
+const char *hww1u1a_get_ps1(void);
+#endif
+
+/* Include a bunch of default commands we probably want */
+#include <config_cmd_default.h>
+
+/* Other helpful shell-like commands */
+#define CONFIG_MD5
+#define CONFIG_SHA1
+#define CONFIG_CMD_MD5SUM
+#define CONFIG_CMD_SHA1
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_SETEXPR
+
+
+/************************************************************************
+ * Image manipulation and booting *
+ ************************************************************************/
+
+/* We use the OpenFirmware-esque "Flattened Device Tree" */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMD_ELF
+#define CONFIG_SYS_BOOTMAPSZ 0x1000000 /* Maximum kernel memory map */
+#define CONFIG_SYS_BOOTM_LEN 0x1000000 /* Maximum kernel size of 16MB */
+
+#if 0
+/* FIXME */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#endif
+
+/* This is the default address for commands with an optional address arg */
+#define CONFIG_LOADADDR 100000
+#define CONFIG_SYS_LOAD_ADDR 0x100000
+
+#define CONFIG_BOOTDELAY 20
+#define CONFIG_BOOTCOMMAND "echo Not yet flashed"
+#define CONFIG_BOOTARGS ""
+#define CONFIG_BOOTARGS_DYNAMIC "console=ttyS0,${baudrate}n1"
+
+/* Extra environment parameters */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "preboot=setenv bootargs \"${bootargs} "CONFIG_BOOTARGS_DYNAMIC"\"\0" \
+ "perf_mode=stable\0" \
+ "memctl_intlv_ctl=2\0" \
+ "flkernel=0xe8020000\0" \
+ "flinitramfs=0xe8800000\0" \
+ "fldevicetree=0xeff20000\0" \
+ "flbootm=bootm ${flkernel} ${flinitramfs} ${fldevicetree}\0" \
+ "flboot=run preboot; run flbootm\0"
+
+#endif /* __CONFIG_H */
--
1.7.1
More information about the U-Boot
mailing list