[U-Boot] [PATCH V3 01/11] mkimage: Add Freescale imx Boot Image support (imximage)
Stefano Babic
sbabic at denx.de
Wed Jan 20 18:19:10 CET 2010
This patch adds support for "imximage" (MX Boot Image)
to the mkimage utility. The imximage is used on the Freescales's
MX.25, MX.35 and MX.51 processors.
Further details under doc/README.imximage.
This patch was tested on a Freescale mx51evk board.
Signed-off-by: Stefano Babic <sbabic at denx.de>
---
Makefile | 4 +
common/image.c | 1 +
doc/README.imximage | 188 +++++++++++++++++++++++++++++
include/image.h | 1 +
tools/Makefile | 2 +
tools/imximage.c | 324 +++++++++++++++++++++++++++++++++++++++++++++++++++
tools/imximage.h | 105 +++++++++++++++++
tools/mkimage.c | 2 +
tools/mkimage.h | 1 +
9 files changed, 628 insertions(+), 0 deletions(-)
create mode 100644 doc/README.imximage
create mode 100644 tools/imximage.c
create mode 100644 tools/imximage.h
diff --git a/Makefile b/Makefile
index ed6156f..365f87f 100644
--- a/Makefile
+++ b/Makefile
@@ -324,6 +324,10 @@ $(obj)u-boot.img: $(obj)u-boot.bin
sed -e 's/"[ ]*$$/ for $(BOARD) board"/') \
-d $< $@
+$(obj)u-boot.imx: $(obj)u-boot.bin
+ $(obj)tools/mkimage -n $(IMX_CONFIG) -T imximage \
+ -e $(TEXT_BASE) -d $< $@
+
$(obj)u-boot.kwb: $(obj)u-boot.bin
$(obj)tools/mkimage -n $(KWD_CONFIG) -T kwbimage \
-a $(TEXT_BASE) -e $(TEXT_BASE) -d $< $@
diff --git a/common/image.c b/common/image.c
index 82e7aa4..9e49713 100644
--- a/common/image.c
+++ b/common/image.c
@@ -140,6 +140,7 @@ static table_entry_t uimage_type[] = {
{ IH_TYPE_STANDALONE, "standalone", "Standalone Program", },
{ IH_TYPE_FLATDT, "flat_dt", "Flat Device Tree", },
{ IH_TYPE_KWBIMAGE, "kwbimage", "Kirkwood Boot Image",},
+ { IH_TYPE_IMXIMAGE, "imximage", "Freescale i.MX Boot Image",},
{ -1, "", "", },
};
diff --git a/doc/README.imximage b/doc/README.imximage
new file mode 100644
index 0000000..9048ef6
--- /dev/null
+++ b/doc/README.imximage
@@ -0,0 +1,188 @@
+---------------------------------------------
+Imximage Boot Image generation using mkimage
+---------------------------------------------
+
+This document describes how to set up a U-Boot image
+that can be booted by Freescale MX25, MX35 and MX51
+processors via internal boot mode.
+
+These processors can boot directly from NAND, SPI flash and SD card flash
+using its internal boot ROM support. They can boot from an internal
+UART, if booting from device media fails.
+Booting from NOR flash does not require to use this image type.
+
+For more details refer Chapter 2 - System Boot and section 2.14
+(flash header description) of the processor's manual.
+
+This implementation does not use at the moment the secure boot feature
+of the processor. The image is generated disabling all security fields.
+
+Command syntax:
+--------------
+./tools/mkimage -l <mx u-boot_file>
+ to list the imx image file details
+
+./tools/mkimage -T imximage \
+ -n <board specific configuration file> \
+ -e <execution address> -d <u-boot binary> <output image file>
+
+For example, for the mx51evk board:
+./tools/mkimage -n ./board/freescale/mx51evk/imximage.cfg \
+ -T imximage -e 0x97800000 \
+ -d u-boot.bin u-boot.imx
+
+You can generate directly the image when you compile u-boot with:
+
+$ make u-boot.imx
+
+The output image can be flashed on the board SPI flash or on a SD card.
+In both cases, you have to copy the image at the offset required for the
+chosen media devices (0x400 for both SPI flash or SD card).
+
+Please check Freescale documentation for further details.
+
+Board specific configuration file specifications:
+-------------------------------------------------
+1. This file must present in the $(BOARDDIR) and the name should be
+ imximage.cfg (since this is used in Makefile).
+2. This file can have empty lines and lines starting with "#" as first
+ character to put comments.
+3. This file can have configuration command lines as mentioned below,
+ any other information in this file is treated as invalid.
+
+Configuration command line syntax:
+---------------------------------
+1. Each command line is must have two strings, first one command or address
+ and second one data string
+2. Following are the valid command strings and associated data strings:-
+ Command string data string
+ -------------- -----------
+ BOOT_FROM nand/spi/sd/onenand
+ Example:
+ BOOT_FROM spi
+ DATA type address value
+
+ type: word=4, halfword=2, byte=1
+ address: physycal register address
+ value: value to be set in register
+ All values are in in hexadecimal.
+ Example (write to IOMUXC):
+ DATA 4 0x73FA88a0 0x200
+
+The processor support up to 60 register programming commands. An error
+is generated if more commands are found in the configuration file.
+
+3. All commands are optional to program.
+
+Setup a SD Card for booting
+--------------------------------
+
+The following example prepare a SD card with u-boot and a FAT partition
+to be used to stored the kernel to be booted.
+I will set the SD in the most compatible mode, setting it with
+255 heads and 63 sectors, as suggested from several documentation and
+howto on line (I took as reference the preparation of a SD Card for the
+Beagleboard, running u-boot as bootloader).
+
+You should start clearing the partitions table on the SD card. Because
+the u-boot image must be stored at the offset 0x400, it must be assured
+that there is no partition at that address. A new SD card is already
+formatted with FAT filesystem and the partition starts from the first
+cylinder, so we need to change it.
+
+You can do all steps with fdisk. If the device for the SD card is
+/dev/mmcblk0, the following commands make the job:
+
+1. Start the fdisk utility (as superuser)
+ fdisk /dev/mmcblk0
+
+2. Clear the actual partition
+
+Command (m for help): o
+
+3. Print card info:
+
+Command (m for help): p
+Disk /dev/mmcblk0: 1981 MB, 1981284352 bytes
+
+In my case, I have a 2 GB card. I need the size to set later the correct value
+for the cylinders.
+
+4. Go to expert mode:
+
+Command (m for help): x
+
+5. Set card geometry
+
+Expert command (m for help): h
+Number of heads (1-256, default 4): 255
+
+Expert command (m for help): s
+Number of sectors (1-63, default 16): 63
+Warning: setting sector offset for DOS compatiblity
+
+We have set 255 heads, 63 sector. We have to set the cylinder.
+The value to be set can be calculated with:
+
+ cilynder = <total size> / <heads> / <sectors> / <blocksize>
+
+in this example,
+ 1981284352 / 255 / 63 / 512 = 239.x = 239
+
+
+Expert command (m for help): c
+Number of cylinders (1-1048576, default 60032): 239
+
+6. Leave the expert mode
+Expert command (m for help): r
+
+7. Set up a partition
+
+Now set a partition table to store the kernel or whatever you want. Of course,
+you can set additional partitions to store rootfs, data, etc.
+In my example I want to set a single partition. I must take care
+to not overwrite the space where I will put u-boot.
+
+Command (m for help): n
+Command action
+ e extended
+ p primary partition (1-4)
+p
+Partition number (1-4): 1
+First cylinder (1-239, default 1): 3
+Last cylinder, +cylinders or +size{K,M,G} (3-239, default 239): +100M
+
+Command (m for help): p
+
+Disk /dev/mmcblk0: 1967 MB, 1967128576 bytes
+255 heads, 63 sectors/track, 239 cylinders
+Units = cylinders of 16065 * 512 = 8225280 bytes
+Disk identifier: 0xb712a870
+
+ Device Boot Start End Blocks Id System
+/dev/mmcblk0p1 3 16 112455 83 Linux
+
+I have set 100MB, leaving the first 2 sectors free. I will copy u-boot
+there.
+
+8. Write the partition table and exit.
+
+Command (m for help): w
+The partition table has been altered!
+
+Calling ioctl() to re-read partition table.
+
+9. Copy u-boot.imx on the SD card
+
+I use dd:
+
+dd if=u-boot.imx of=/dev/mmcblk0 bs=512 seek=2
+
+This command copies the u-boot image at the address 0x400, as required
+by the processor.
+
+Now remove your card from the PC and go to the target. If evrything went right,
+the u-boot prompt should come after power on.
+
+------------------------------------------------
+Author: Stefano babic <sbabic at denx.de>
diff --git a/include/image.h b/include/image.h
index d2e78fe..3e959de 100644
--- a/include/image.h
+++ b/include/image.h
@@ -156,6 +156,7 @@
#define IH_TYPE_FILESYSTEM 7 /* Filesystem Image (any type) */
#define IH_TYPE_FLATDT 8 /* Binary Flat Device Tree Blob */
#define IH_TYPE_KWBIMAGE 9 /* Kirkwood Boot Image */
+#define IH_TYPE_IMXIMAGE 10 /* Freescale IMXBoot Image */
/*
* Compression Types
diff --git a/tools/Makefile b/tools/Makefile
index 5b8c3c3..73640e6 100644
--- a/tools/Makefile
+++ b/tools/Makefile
@@ -73,6 +73,7 @@ OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o
OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o
OBJ_FILES-$(CONFIG_INCA_IP) += inca-swap-bytes.o
NOPED_OBJ_FILES-y += kwbimage.o
+NOPED_OBJ_FILES-y += imximage.o
NOPED_OBJ_FILES-y += mkimage.o
OBJ_FILES-$(CONFIG_NETCONSOLE) += ncb.o
NOPED_OBJ_FILES-y += os_support.o
@@ -158,6 +159,7 @@ $(obj)mkimage$(SFX): $(obj)crc32.o \
$(obj)default_image.o \
$(obj)fit_image.o \
$(obj)image.o \
+ $(obj)imximage.o \
$(obj)kwbimage.o \
$(obj)md5.o \
$(obj)mkimage.o \
diff --git a/tools/imximage.c b/tools/imximage.c
new file mode 100644
index 0000000..c1fdafb
--- /dev/null
+++ b/tools/imximage.c
@@ -0,0 +1,324 @@
+/*
+ * (C) Copyright 2009
+ * Stefano Babic, DENX Software Engineering, sbabic at denx.de.
+ *
+ * (C) Copyright 2008
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include "mkimage.h"
+#include <image.h>
+#include "imximage.h"
+
+/*
+ * Supported commands for configuration file
+ */
+static table_entry_t imximage_cmds[] = {
+ {CMD_BOOT_FROM, "BOOT_FROM", "boot comand", },
+ {CMD_DATA, "DATA", "Reg Write Data", },
+ {-1, "", "", },
+};
+
+/*
+ * Supported Boot options for configuration file
+ * this is needed to set the correct flash offset
+ */
+static table_entry_t imximage_bootops[] = {
+ {FLASH_OFFSET_SPI, "spi", "SPI Flash", },
+ {FLASH_OFFSET_NAND, "nand", "NAND Flash", },
+ {FLASH_OFFSET_SD, "sd", "SD Card", },
+ {FLASH_OFFSET_ONENAND, "onenand", "OneNAND Flash",},
+ {-1, "", "Invalid", },
+};
+
+
+static struct imx_header imximage_header;
+
+static uint32_t get_cfg_value(char *token, char *name, int linenr)
+{
+ char *endptr;
+ uint32_t value;
+
+ errno = 0;
+ value = strtoul(token, &endptr, 16);
+ if (errno || (token == endptr)) {
+ fprintf(stderr, "Error: %s[%d] - Invalid hex data(%s)\n",
+ name, linenr, token);
+ exit(EXIT_FAILURE);
+ }
+ return value;
+}
+
+static int imximage_check_image_types(uint8_t type)
+{
+ if (type == IH_TYPE_IMXIMAGE)
+ return EXIT_SUCCESS;
+ else
+ return EXIT_FAILURE;
+}
+
+static int imximage_verify_header(unsigned char *ptr, int image_size,
+ struct mkimage_params *params)
+{
+
+ struct imx_header *imx_hdr = (struct imx_header *) ptr;
+ flash_header_t *hdr = &imx_hdr->fhdr;
+
+ /* Only a few checks can be done: search for magic numbers */
+ if (hdr->app_code_barker != APP_CODE_BARKER)
+ return -FDT_ERR_BADSTRUCTURE;
+
+ if (imx_hdr->dcd_table.preamble.barker != DCD_BARKER)
+ return -FDT_ERR_BADSTRUCTURE;
+
+ return 0;
+}
+
+static void imximage_print_header(const void *ptr)
+{
+ struct imx_header *imx_hdr = (struct imx_header *) ptr;
+ flash_header_t *hdr = &imx_hdr->fhdr;
+ uint32_t size;
+ flash_cfg_parms_t *ext_header;
+
+ size = imx_hdr->dcd_table.preamble.length;
+ if (size > (MAX_HW_CFG_SIZE * sizeof(dcd_type_addr_data_t))) {
+ fprintf(stderr,
+ "Error: Image corrupt DCD size %d exceed maximum %d\n",
+ size / sizeof(dcd_type_addr_data_t), MAX_HW_CFG_SIZE);
+ exit(EXIT_FAILURE);
+ }
+
+ ext_header = (flash_cfg_parms_t *) ((uint32_t)&imx_hdr->dcd_table +
+ sizeof(dcd_preamble_t) + size);
+
+ printf("Image Type: Freescale IMX Boot Image\n");
+ printf("Data Size: ");
+ genimg_print_size(ext_header->length);
+ printf("Load Address: %08x\n", (unsigned int)hdr->app_dest_ptr);
+ printf("Entry Point: %08x\n", (unsigned int)hdr->app_code_jump_vector);
+}
+
+static uint32_t imximage_parse_cfg_file(struct imx_header *imxhdr, char *name)
+{
+ FILE *fd = NULL;
+ char *line = NULL;
+ char *token, *saveptr1, *saveptr2;
+ int lineno = 0;
+ int fld, value;
+ uint32_t len;
+ int dcd_len = 0;
+ dcd_t *dcd = &imxhdr->dcd_table;
+ int32_t cmd;
+
+ fd = fopen(name, "r");
+ if (fd == 0) {
+ fprintf(stderr, "Error: %s - Can't open DCD file\n", name);
+ exit(EXIT_FAILURE);
+ }
+
+ /* Very simple parsing, line starting with # are comments
+ * and are dropped
+ */
+ while ((getline(&line, &len, fd)) > 0) {
+ lineno++;
+
+ token = strtok_r(line, "\r\n", &saveptr1);
+ if (token == NULL)
+ continue;
+
+ /* Check inside the single line */
+ for (fld = CFG_COMMAND, cmd = CMD_INVALID,
+ line = token; ; line = NULL, fld++) {
+ token = strtok_r(line, " \t", &saveptr2);
+ if (token == NULL)
+ break;
+
+ /* Drop all text starting with '#' as comments */
+ if (token[0] == '#')
+ break;
+
+ /* parse all fields in a single line */
+ switch (fld) {
+ case CFG_COMMAND:
+ cmd = get_table_entry_id(imximage_cmds,
+ "imximage commands", token);
+ if (cmd < 0) {
+ fprintf(stderr,
+ "Error: %s[%d] - "
+ "Invalid command (%s)\n",
+ name, lineno, token);
+ exit(EXIT_FAILURE);
+ }
+ break;
+ case CFG_REG_SIZE:
+ switch (cmd) {
+ case CMD_BOOT_FROM:
+ /* Get flash header offset */
+ imxhdr->flash_offset =
+ get_table_entry_id(
+ imximage_bootops,
+ "imximage boot option",
+ token);
+ if (imxhdr->flash_offset == -1) {
+ fprintf(stderr,
+ "Error: %s[%d] -"
+ "Invalid boot device"
+ "(%s)\n",
+ name, lineno, token);
+ exit(EXIT_FAILURE);
+ }
+ break;
+ case CMD_DATA:
+ value = get_cfg_value(token,
+ name, lineno);
+
+ /* Byte, halfword, word */
+ if ((value != 1) &&
+ (value != 2) && (value != 4)) {
+ fprintf(stderr,
+ "Error: %s[%d] - "
+ "Invalid register size "
+ "(%d)\n",
+ name, lineno, value);
+ exit(EXIT_FAILURE);
+ }
+ dcd->addr_data[dcd_len].type = value;
+ break;
+ }
+
+ case CFG_REG_ADDRESS:
+ if (cmd == CMD_DATA)
+ dcd->addr_data[dcd_len].addr =
+ get_cfg_value(token,
+ name, lineno);
+ break;
+ case CFG_REG_VALUE:
+ if (cmd == CMD_DATA) {
+ dcd->addr_data[dcd_len].value =
+ get_cfg_value(token,
+ name, lineno);
+ dcd_len++;
+ }
+ break;
+ }
+ }
+
+ if (dcd_len > MAX_HW_CFG_SIZE) {
+ fprintf(stderr,
+ "Error: %s[%d] -"
+ "DCD table exceeds maximum size(%d)\n",
+ name, lineno, MAX_HW_CFG_SIZE);
+ }
+ }
+ dcd->preamble.barker = DCD_BARKER;
+ dcd->preamble.length = dcd_len * sizeof(dcd_type_addr_data_t);
+ fclose(fd);
+
+ return dcd->preamble.length;
+}
+
+static void imximage_set_header(void *ptr, struct stat *sbuf, int ifd,
+ struct mkimage_params *params)
+{
+ struct imx_header *hdr = (struct imx_header *)ptr;
+ flash_header_t *fhdr = &hdr->fhdr;
+ int dcd_len;
+ flash_cfg_parms_t *ext_header;
+ uint32_t base_offset;
+
+ /* Set default offset */
+ hdr->flash_offset = FLASH_OFFSET_STANDARD;
+
+ /* Set magic number */
+ fhdr->app_code_barker = APP_CODE_BARKER;
+
+ /* Parse dcd configuration file */
+ dcd_len = imximage_parse_cfg_file(hdr, params->imagename);
+
+ fhdr->app_dest_ptr = params->addr;
+ fhdr->app_dest_ptr = params->ep - hdr->flash_offset -
+ sizeof(struct imx_header);
+ fhdr->app_code_jump_vector = params->ep;
+
+ base_offset = fhdr->app_dest_ptr + hdr->flash_offset ;
+ fhdr->dcd_ptr_ptr = (uint32_t) ((uint32_t)&fhdr->dcd_ptr -
+ (uint32_t)&fhdr->app_code_jump_vector) + base_offset ;
+
+ fhdr->dcd_ptr = base_offset +
+ ((uint32_t)&hdr->dcd_table -
+ (uint32_t)&hdr->fhdr);
+
+ /* The external flash header must be at the end of the DCD table */
+ ext_header = (flash_cfg_parms_t *) ((uint32_t)&hdr->dcd_table +
+ dcd_len +
+ sizeof(dcd_preamble_t));
+ ext_header->length = sbuf->st_size +
+ hdr->flash_offset +
+ sizeof(struct imx_header);
+
+ /* Security feature are not supported */
+ fhdr->app_code_csf = 0;
+ fhdr->super_root_key = NULL;
+
+}
+
+int imximage_check_params(struct mkimage_params *params)
+{
+ if (!params)
+ return CFG_INVALID;
+ if (!strlen(params->imagename)) {
+ fprintf(stderr, "Error: %s - Configuration file not specified, "
+ "it is needed for imximage generation\n",
+ params->cmdname);
+ return CFG_INVALID;
+ }
+ /*
+ * Check parameters:
+ * XIP is not allowed and verify that incompatible
+ * parameters are not sent at the same time
+ * For example, if list is required a data image must not be provided
+ */
+ return (params->dflag && (params->fflag || params->lflag)) ||
+ (params->fflag && (params->dflag || params->lflag)) ||
+ (params->lflag && (params->dflag || params->fflag)) ||
+ (params->xflag) || !(strlen(params->imagename));
+}
+
+/*
+ * imximage parameters
+ */
+static struct image_type_params imximage_params = {
+ .name = "Freescale i.MX 51 Boot Image support",
+ .header_size = sizeof(struct imx_header),
+ .hdr = (void *)&imximage_header,
+ .check_image_type = imximage_check_image_types,
+ .verify_header = imximage_verify_header,
+ .print_header = imximage_print_header,
+ .set_header = imximage_set_header,
+ .check_params = imximage_check_params,
+};
+
+void init_imx_image_type(void)
+{
+ mkimage_register(&imximage_params);
+}
diff --git a/tools/imximage.h b/tools/imximage.h
new file mode 100644
index 0000000..c579f51
--- /dev/null
+++ b/tools/imximage.h
@@ -0,0 +1,105 @@
+/*
+ * (C) Copyright 2009
+ * Stefano Babic, DENX Software Engineering, sbabic at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _IMXIMAGE_H_
+#define _IMXIMAGE_H_
+
+#define MAX_HW_CFG_SIZE 60 /* Max number of registers imx can set */
+#define MAX_EXP_SIZE 4
+#define APP_CODE_BARKER 0xB1
+#define DCD_BARKER 0xB17219E9
+#define HEADER_OFFSET 0x400
+
+
+#define CMD_DATA_STR "DATA"
+#define FLASH_OFFSET_STANDARD 0x400
+#define FLASH_OFFSET_NAND FLASH_OFFSET_STANDARD
+#define FLASH_OFFSET_SD FLASH_OFFSET_STANDARD
+#define FLASH_OFFSET_SPI FLASH_OFFSET_STANDARD
+#define FLASH_OFFSET_ONENAND 0x100
+
+enum imximage_cmd {
+ CMD_INVALID,
+ CMD_BOOT_FROM,
+ CMD_DATA
+};
+
+enum imximage_fld_types {
+ CFG_INVALID = -1,
+ CFG_COMMAND,
+ CFG_REG_SIZE,
+ CFG_REG_ADDRESS,
+ CFG_REG_VALUE
+};
+
+typedef struct {
+ uint8_t rsa_exponent[MAX_EXP_SIZE]; /* RSA public exponent */
+ uint8_t *rsa_modulus; /* RSA modulus pointer */
+ uint16_t exponent_size; /* Exponent size (bytes) */
+ uint16_t modulus_size; /* Modulus size (bytes) */
+ uint8_t init_flag; /* key initialized */
+} hab_rsa_public_key;
+
+typedef struct {
+ uint32_t type; /* Type of pointer (byte, halfword, word, wait/read) */
+ uint32_t addr; /* Address to write to */
+ uint32_t value; /* Data to write */
+} dcd_type_addr_data_t;
+
+typedef struct {
+ uint32_t barker; /* Barker for sanity check */
+ uint32_t length; /* Device configuration length (without preamble) */
+} dcd_preamble_t;
+
+typedef struct {
+ dcd_preamble_t preamble;
+ dcd_type_addr_data_t addr_data[MAX_HW_CFG_SIZE];
+} dcd_t;
+
+typedef struct {
+ uint32_t app_code_jump_vector;
+ uint32_t app_code_barker;
+ uint32_t app_code_csf;
+ uint32_t dcd_ptr_ptr;
+ hab_rsa_public_key *super_root_key;
+ uint32_t dcd_ptr;
+ uint32_t app_dest_ptr;
+} flash_header_t;
+
+typedef struct {
+ uint32_t length; /* Length of data to be read from flash */
+} flash_cfg_parms_t;
+
+struct imx_header {
+ flash_header_t fhdr;
+ dcd_t dcd_table;
+ flash_cfg_parms_t ext_header;
+ uint32_t flash_offset;
+};
+
+struct reg_config {
+ uint32_t raddr;
+ uint32_t rdata;
+};
+
+#endif /* _IMXIMAGE_H_ */
diff --git a/tools/mkimage.c b/tools/mkimage.c
index 1bed933..cf4b754 100644
--- a/tools/mkimage.c
+++ b/tools/mkimage.c
@@ -150,6 +150,8 @@ main (int argc, char **argv)
/* Init Kirkwood Boot image generation/list support */
init_kwb_image_type ();
+ /* Init Freescale imx Boot image generation/list support */
+ init_imx_image_type ();
/* Init FIT image generation/list support */
init_fit_image_type ();
/* Init Default image generation/list support */
diff --git a/tools/mkimage.h b/tools/mkimage.h
index ec67336..9033a7d 100644
--- a/tools/mkimage.h
+++ b/tools/mkimage.h
@@ -140,6 +140,7 @@ void mkimage_register (struct image_type_params *tparams);
* Supported image types init functions
*/
void init_kwb_image_type (void);
+void init_imx_image_type (void);
void init_default_image_type (void);
void init_fit_image_type (void);
--
1.6.3.3
More information about the U-Boot
mailing list