[U-Boot] FW: Issue in TFTP using LSI Ethernet Phyceiver

[Balaji Sivakumar, ERS, HCLTech]

Hi,

Request your reply on the below request, Could you pls provide me the solution or anyone faced the same issue.

Am using the latest U-boot.



Thanks ,
ShivBalaji
________________________________________
From: Balaji Sivakumar, ERS, HCLTech
Sent: Thursday, July 01, 2010 8:44 PM
To: u-boot at lists.denx.de
Cc: Balaji Sivakumar, ERS, HCLTech
Subject: Issue in TFTP using LSI Ethernet Phyceiver

Hi,

We are currently working on a hardware board design project for an Industrial application.
The processor used in TMS320DM6467ZUTA. We are facing an issue with ethernet interface.

The Ethernet PHYceiver IC interfaced with processor is L-ET1011C2-C-D (Gigabit Ethernet PHYceiver from LSI).

The Ethernet PHYceiver IC is configured by processor through MDIO interface.
We are able to read all Ethernet PHYceiver IC registers correctly at MD clock frequency of 4.5 MHz.
The Ethernet PHYceiver IC  is connected to RJ-45 port.

When we are connecting cross over cable between our Processor board and the Test PC,
we could notice LAN connected (speed 100 MBPS) on our Test PC.
We configured separate static IP address for Processor board and Test PC.
When we try to ping, the ping is getting failed (Error message: "HOST is Not Alive")

I have also tried running the tftp sever in my test pc and typed the tftp in the command terminal, it is trying to load the file
and it is timing out after some time.

NOTE: The Processor board has same ethernet interface as there in TMS320DM6467 Eval board.
We are able to see the Ethernet PHYceiver IC recognized by the UBOOT.
Pls find bootup message when i power cycle board, it recognizes the Phyceiver.

U-Boot 2009.08 (Jul 01 2010 - 15:45:29)
I2C:   ready
DRAM:  256 MB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
ARM Clock :- 297MHz
DDR Clock :- 297MHz
Net:   Ethernet PHY ID: 282f014
Ethernet PHY: GENERIC @ 0x01
Hit any key to stop autoboot:  0
Please find environmental variables am setting.
bootdelay=4
baudrate=115200
bootfile="uImage"
addclk=setenv bootargs ${bootargs} clkref=${clkref}
ethact=
filesize=2740C7
bootcmd=nand read 81100000 4a0000 500000; nboot 80700000 0 a0000; bootm
bootargs=console=ttyS0,115200n8 root=/dev/ram rw initrd=0x81100000,16M mem=120M
ip=dhcp
stdin=serial
stdout=serial
stderr=serial
ver=U-Boot 2009.08 (Jul 01 2010 - 15:45:29)
ipaddr=192.168.25.2
serverip=192.168.25.1
subnetmask=255.255.255.0
netmask=255.255.255.0

Request you to provide valuable suggestions to fix our issue.
Regards,
Balaji S
Thanks ,
ShivBalaji

DISCLAIMER:
-----------------------------------------------------------------------------------------------------------------------

The contents of this e-mail and any attachment(s) are confidential and intended for the named recipient(s) only. 
It shall not attach any liability on the originator or HCL or its affiliates. Any views or opinions presented in 
this email are solely those of the author and may not necessarily reflect the opinions of HCL or its affiliates. 
Any form of reproduction, dissemination, copying, disclosure, modification, distribution and / or publication of 
this message without the prior written consent of the author of this e-mail is strictly prohibited. If you have 
received this email in error please delete it and notify the sender immediately. Before opening any mail and 
attachments please check them for viruses and defect.

-----------------------------------------------------------------------------------------------------------------------