[U-Boot] [PATCH 11/35] Blackfin: switch to common GPIO LED driver
Mike Frysinger
vapier at gentoo.org
Mon Jul 5 11:30:16 CEST 2010
Now that we have a unified gpio layer, the different status led
implementations can be switched to the common gpio led driver.
Signed-off-by: Mike Frysinger <vapier at gentoo.org>
---
board/bf526-ezbrd/Makefile | 1 -
board/bf526-ezbrd/status-led.c | 56 ---------------------------------------
board/bf533-stamp/bf533-stamp.c | 37 -------------------------
include/configs/bf526-ezbrd.h | 6 +++-
include/configs/bf533-stamp.h | 10 ++++---
5 files changed, 10 insertions(+), 100 deletions(-)
delete mode 100644 board/bf526-ezbrd/status-led.c
diff --git a/board/bf526-ezbrd/Makefile b/board/bf526-ezbrd/Makefile
index a9ff760..f2bd2c2 100644
--- a/board/bf526-ezbrd/Makefile
+++ b/board/bf526-ezbrd/Makefile
@@ -30,7 +30,6 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).a
COBJS-y := $(BOARD).o
-COBJS-$(CONFIG_STATUS_LED) += status-led.o
SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS-y))
diff --git a/board/bf526-ezbrd/status-led.c b/board/bf526-ezbrd/status-led.c
deleted file mode 100644
index 6327022..0000000
--- a/board/bf526-ezbrd/status-led.c
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- * U-boot - status leds
- *
- * Copyright (c) 2005-2009 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
- */
-
-#include <common.h>
-#include <config.h>
-#include <command.h>
-#include <status_led.h>
-
-static void set_led_f(int pf, int state)
-{
- switch (state) {
- case STATUS_LED_OFF: bfin_write_PORTFIO_CLEAR(pf); break;
- case STATUS_LED_BLINKING: bfin_write_PORTFIO_TOGGLE(pf); break;
- case STATUS_LED_ON: bfin_write_PORTFIO_SET(pf); break;
- }
-}
-static void set_led_g(int pf, int state)
-{
- switch (state) {
- case STATUS_LED_OFF: bfin_write_PORTGIO_CLEAR(pf); break;
- case STATUS_LED_BLINKING: bfin_write_PORTGIO_TOGGLE(pf); break;
- case STATUS_LED_ON: bfin_write_PORTGIO_SET(pf); break;
- }
-}
-
-static void set_leds(led_id_t mask, int state)
-{
- if (mask & 0x1) set_led_f(PF8, state);
- if (mask & 0x2) set_led_g(PG11, state);
- if (mask & 0x4) set_led_g(PG12, state);
-}
-
-void __led_init(led_id_t mask, int state)
-{
- bfin_write_PORTF_FER(bfin_read_PORTF_FER() & ~(PF8));
- bfin_write_PORTG_FER(bfin_read_PORTG_FER() & ~(PG11 | PG12));
- bfin_write_PORTFIO_INEN(bfin_read_PORTFIO_INEN() & ~(PF8));
- bfin_write_PORTGIO_INEN(bfin_read_PORTGIO_INEN() & ~(PG11 | PG12));
- bfin_write_PORTFIO_DIR(bfin_read_PORTFIO_DIR() | (PF8));
- bfin_write_PORTGIO_DIR(bfin_read_PORTGIO_DIR() | (PG11 | PG12));
-}
-
-void __led_set(led_id_t mask, int state)
-{
- set_leds(mask, state);
-}
-
-void __led_toggle(led_id_t mask)
-{
- set_leds(mask, STATUS_LED_BLINKING);
-}
diff --git a/board/bf533-stamp/bf533-stamp.c b/board/bf533-stamp/bf533-stamp.c
index 4abad08..fd10eae 100644
--- a/board/bf533-stamp/bf533-stamp.c
+++ b/board/bf533-stamp/bf533-stamp.c
@@ -134,43 +134,6 @@ void show_boot_progress(int status)
}
#endif
-#ifdef CONFIG_STATUS_LED
-#include <status_led.h>
-
-static void set_led(int pf, int state)
-{
- switch (state) {
- case STATUS_LED_OFF: bfin_write_FIO_FLAG_S(pf); break;
- case STATUS_LED_BLINKING: bfin_write_FIO_FLAG_T(pf); break;
- case STATUS_LED_ON: bfin_write_FIO_FLAG_C(pf); break;
- }
-}
-
-static void set_leds(led_id_t mask, int state)
-{
- if (mask & 0x1) set_led(PF2, state);
- if (mask & 0x2) set_led(PF3, state);
- if (mask & 0x4) set_led(PF4, state);
-}
-
-void __led_init(led_id_t mask, int state)
-{
- bfin_write_FIO_INEN(bfin_read_FIO_INEN() & ~(PF2 | PF3 | PF4));
- bfin_write_FIO_DIR(bfin_read_FIO_DIR() | (PF2 | PF3 | PF4));
-}
-
-void __led_set(led_id_t mask, int state)
-{
- set_leds(mask, state);
-}
-
-void __led_toggle(led_id_t mask)
-{
- set_leds(mask, STATUS_LED_BLINKING);
-}
-
-#endif
-
#ifdef CONFIG_SMC91111
int board_eth_init(bd_t *bis)
{
diff --git a/include/configs/bf526-ezbrd.h b/include/configs/bf526-ezbrd.h
index 52aeb5c..ecda216 100644
--- a/include/configs/bf526-ezbrd.h
+++ b/include/configs/bf526-ezbrd.h
@@ -160,17 +160,19 @@
/* define to enable run status via led */
/* #define CONFIG_STATUS_LED */
#ifdef CONFIG_STATUS_LED
+#define CONFIG_GPIO_LED
#define CONFIG_BOARD_SPECIFIC_LED
/* use LED0 to indicate booting/alive */
#define STATUS_LED_BOOT 0
-#define STATUS_LED_BIT 1
+#define STATUS_LED_BIT GPIO_PF8
#define STATUS_LED_STATE STATUS_LED_ON
#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
/* use LED1 to indicate crash */
#define STATUS_LED_CRASH 1
-#define STATUS_LED_BIT1 2
+#define STATUS_LED_BIT1 GPIO_PG11
#define STATUS_LED_STATE1 STATUS_LED_ON
#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+/* #define STATUS_LED_BIT2 GPIO_PG12 */
#endif
diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
index d5e82ca..2ec9c42 100644
--- a/include/configs/bf533-stamp.h
+++ b/include/configs/bf533-stamp.h
@@ -230,17 +230,19 @@
/* define to enable run status via led */
/* #define CONFIG_STATUS_LED */
#ifdef CONFIG_STATUS_LED
+#define CONFIG_GPIO_LED
#define CONFIG_BOARD_SPECIFIC_LED
-/* use LED1 to indicate booting/alive */
+/* use LED0 to indicate booting/alive */
#define STATUS_LED_BOOT 0
-#define STATUS_LED_BIT 1
+#define STATUS_LED_BIT GPIO_PF2
#define STATUS_LED_STATE STATUS_LED_ON
#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
-/* use LED2 to indicate crash */
+/* use LED1 to indicate crash */
#define STATUS_LED_CRASH 1
-#define STATUS_LED_BIT1 2
+#define STATUS_LED_BIT1 GPIO_PF3
#define STATUS_LED_STATE1 STATUS_LED_ON
#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+/* #define STATUS_LED_BIT2 GPIO_PF4 */
#endif
/* define to enable splash screen support */
--
1.7.1.1
More information about the U-Boot
mailing list