[U-Boot] [PATCH v2] powerpc/p4080: Add support for the P4080DS board
Kumar Gala
galak at kernel.crashing.org
Mon Jul 26 20:12:07 CEST 2010
Add support for the P4080DS board, with the following features:
* 36-bit only
* Boots from NOR flash
* FMAN drivers NOT supported
* SPD DDR initialization
Signed-off-by: Ed Swarthout <Ed.Swarthout at freescale.com>
Signed-off-by: Emil Medve <Emilian.Medve at Freescale.com>
Signed-off-by: Becky Bruce <beckyb at kernel.crashing.org>
Signed-off-by: Ashish Kalra <Ashish.Kalra at freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder at freescale.com>
Signed-off-by: Dave Liu <daveliu at freescale.com>
Signed-off-by: Lan Chunhe-B25806 <b25806 at freescale.com>
Signed-off-by: Scott Wood <scottwood at freescale.com>
Signed-off-by: Kim Phillips <kim.phillips at freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang at freescale.com>
Signed-off-by: Timur Tabi <timur at freescale.com>
Signed-off-by: Andy Fleming <afleming at freescale.com>
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Kumar Gala <galak at kernel.crashing.org>
---
* Dropped non-SPD ddr setup
* cleaned up some whitespace issues
MAKEALL | 1 +
board/freescale/common/Makefile | 1 +
board/freescale/corenet_ds/Makefile | 55 +++
board/freescale/corenet_ds/config.mk | 30 ++
board/freescale/corenet_ds/corenet_ds.c | 259 ++++++++++++
board/freescale/corenet_ds/ddr.c | 176 ++++++++
board/freescale/corenet_ds/law.c | 40 ++
board/freescale/corenet_ds/pci.c | 127 ++++++
board/freescale/corenet_ds/tlb.c | 112 +++++
boards.cfg | 1 +
include/configs/P4080DS.h | 35 ++
include/configs/corenet_ds.h | 673 +++++++++++++++++++++++++++++++
12 files changed, 1510 insertions(+), 0 deletions(-)
create mode 100644 board/freescale/corenet_ds/Makefile
create mode 100644 board/freescale/corenet_ds/config.mk
create mode 100644 board/freescale/corenet_ds/corenet_ds.c
create mode 100644 board/freescale/corenet_ds/ddr.c
create mode 100644 board/freescale/corenet_ds/law.c
create mode 100644 board/freescale/corenet_ds/pci.c
create mode 100644 board/freescale/corenet_ds/tlb.c
create mode 100644 include/configs/P4080DS.h
create mode 100644 include/configs/corenet_ds.h
diff --git a/MAKEALL b/MAKEALL
index 2133559..b34ae33 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -428,6 +428,7 @@ LIST_85xx=" \
P2020RDB_NAND \
P2020RDB_SDCARD \
P2020RDB_SPIFLASH \
+ P4080DS \
PM854 \
PM856 \
sbc8540 \
diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 2d48d7e..f93045f 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -46,6 +46,7 @@ COBJS-$(CONFIG_MPC8536DS) += ics307_clk.o
COBJS-$(CONFIG_MPC8572DS) += ics307_clk.o
COBJS-$(CONFIG_P1022DS) += ics307_clk.o
COBJS-$(CONFIG_P2020DS) += ics307_clk.o
+COBJS-$(CONFIG_P4080DS) += ics307_clk.o
SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS-y))
diff --git a/board/freescale/corenet_ds/Makefile b/board/freescale/corenet_ds/Makefile
new file mode 100644
index 0000000..8aa7255
--- /dev/null
+++ b/board/freescale/corenet_ds/Makefile
@@ -0,0 +1,55 @@
+#
+# Copyright 2007-2009 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS-y += $(BOARD).o
+COBJS-$(CONFIG_DDR_SPD) += ddr.o
+COBJS-$(CONFIG_PCI) += pci.o
+COBJS-y += law.o
+COBJS-y += tlb.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/corenet_ds/config.mk b/board/freescale/corenet_ds/config.mk
new file mode 100644
index 0000000..72db24e
--- /dev/null
+++ b/board/freescale/corenet_ds/config.mk
@@ -0,0 +1,30 @@
+#
+# Copyright 2007-2009 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# P4080DS board
+#
+ifndef TEXT_BASE
+TEXT_BASE = 0xeff80000
+endif
+
+RESET_VECTOR_ADDRESS = 0xeffffffc
diff --git a/board/freescale/corenet_ds/corenet_ds.c b/board/freescale/corenet_ds/corenet_ds.c
new file mode 100644
index 0000000..3cdefb3
--- /dev/null
+++ b/board/freescale/corenet_ds/corenet_ds.c
@@ -0,0 +1,259 @@
+/*
+ * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+
+extern void pci_of_setup(void *blob, bd_t *bd);
+
+#include "../common/ngpixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void cpu_mp_lmb_reserve(struct lmb *lmb);
+
+int checkboard (void)
+{
+ u8 sw;
+ struct cpu_type *cpu = gd->cpu;
+
+ printf("Board: %sDS, ", cpu->name);
+ printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
+ in_8(&pixis->id), in_8(&pixis->arch), in_8(&pixis->scver));
+
+ sw = in_8(&PIXIS_SW(PIXIS_LBMAP_SWITCH));
+ sw = (sw & PIXIS_LBMAP_MASK) >> PIXIS_LBMAP_SHIFT;
+
+ if (sw < 0x8)
+ printf("vBank: %d\n", sw);
+ else if (sw == 0x8)
+ puts("Promjet\n");
+ else if (sw == 0x9)
+ puts("NAND\n");
+ else
+ printf("invalid setting of SW%u\n", PIXIS_LBMAP_SWITCH);
+
+#ifdef CONFIG_PHYS_64BIT
+ puts("36-bit Addressing\n");
+#endif
+
+ /* Display the actual SERDES reference clocks as configured by the
+ * dip switches on the board. Note that the SWx registers could
+ * technically be set to force the reference clocks to match the
+ * values that the SERDES expects (or vice versa). For now, however,
+ * we just display both values and hope the user notices when they
+ * don't match.
+ */
+ puts("SERDES Reference Clocks: ");
+ sw = in_8(&PIXIS_SW(3));
+ printf("Bank1=%uMHz ", (sw & 0x40) ? 125 : 100);
+ printf("Bank2=%sMHz ", (sw & 0x20) ? "156.25" : "125");
+ printf("Bank3=%sMHz\n", (sw & 0x10) ? "156.25" : "125");
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+ /*
+ * P4080 DS board only uses the DDR1_MCK0/3 and DDR2_MCK0/3
+ * disable the DDR1_MCK1/2/4/5 and DDR2_MCK1/2/4/5 to reduce
+ * the noise introduced by these unterminated and unused clock pairs.
+ */
+ setbits_be32(&gur->ddrclkdr, 0x001B001B);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash + PROMJET region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash + promjet */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, /* tlb, epn, rpn */
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, /* perms, wimge */
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1); /* ts, esel, tsize, iprot */
+
+ set_liodns();
+ setup_portals();
+
+#ifdef CONFIG_SRIO1
+ if (is_serdes_configured(SRIO1)) {
+ set_next_law(CONFIG_SYS_RIO1_MEM_PHYS, LAW_SIZE_256M,
+ LAW_TRGT_IF_RIO_1);
+ } else {
+ printf (" SRIO1: disabled\n");
+ }
+#else
+ setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_SRIO1); /* disable */
+#endif
+
+#ifdef CONFIG_SRIO2
+ if (is_serdes_configured(SRIO2)) {
+ set_next_law(CONFIG_SYS_RIO2_MEM_PHYS, LAW_SIZE_256M,
+ LAW_TRGT_IF_RIO_2);
+ } else {
+ printf (" SRIO2: disabled\n");
+ }
+#else
+ setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_SRIO2); /* disable */
+#endif
+
+ return 0;
+}
+
+static const char *serdes_clock_to_string(u32 clock)
+{
+ switch(clock) {
+ case SRDS_PLLCR0_RFCK_SEL_100:
+ return "100";
+ case SRDS_PLLCR0_RFCK_SEL_125:
+ return "125";
+ case SRDS_PLLCR0_RFCK_SEL_156_25:
+ return "156.25";
+ default:
+ return "???";
+ }
+}
+
+#define NUM_SRDS_BANKS 3
+
+int misc_init_r(void)
+{
+ serdes_corenet_t *srds_regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+ u32 actual[NUM_SRDS_BANKS];
+ unsigned int i;
+ u8 sw3;
+
+ /* Warn if the expected SERDES reference clocks don't match the
+ * actual reference clocks. This needs to be done after calling
+ * p4080_erratum_serdes8(), since that function may modify the clocks.
+ */
+ sw3 = in_8(&PIXIS_SW(3));
+ actual[0] = (sw3 & 0x40) ?
+ SRDS_PLLCR0_RFCK_SEL_125 : SRDS_PLLCR0_RFCK_SEL_100;
+ actual[1] = (sw3 & 0x20) ?
+ SRDS_PLLCR0_RFCK_SEL_156_25 : SRDS_PLLCR0_RFCK_SEL_125;
+ actual[2] = (sw3 & 0x10) ?
+ SRDS_PLLCR0_RFCK_SEL_156_25 : SRDS_PLLCR0_RFCK_SEL_125;
+
+ for (i = 0; i < NUM_SRDS_BANKS; i++) {
+ u32 expected = srds_regs->bank[i].pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK;
+ if (expected != actual[i]) {
+ printf("Warning: SERDES bank %u expects reference clock"
+ " %sMHz, but actual is %sMHz\n", i + 1,
+ serdes_clock_to_string(expected),
+ serdes_clock_to_string(actual[i]));
+ }
+ }
+
+ return 0;
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing....\n");
+
+ dram_size = fsl_ddr_sdram();
+
+ setup_ddr_tlbs(dram_size / 0x100000);
+
+ puts(" DDR: ");
+ return dram_size;
+}
+
+#ifdef CONFIG_MP
+void board_lmb_reserve(struct lmb *lmb)
+{
+ cpu_mp_lmb_reserve(lmb);
+}
+#endif
+
+void ft_srio_setup(void *blob)
+{
+#ifdef CONFIG_SRIO1
+ if (!is_serdes_configured(SRIO1)) {
+ fdt_del_node_and_alias(blob, "rio0");
+ }
+#else
+ fdt_del_node_and_alias(blob, "rio0");
+#endif
+#ifdef CONFIG_SRIO2
+ if (!is_serdes_configured(SRIO2)) {
+ fdt_del_node_and_alias(blob, "rio1");
+ }
+#else
+ fdt_del_node_and_alias(blob, "rio1");
+#endif
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ ft_srio_setup(blob);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+}
+
+int board_eth_init(bd_t *bis)
+{
+ return pci_eth_init(bis);
+}
diff --git a/board/freescale/corenet_ds/ddr.c b/board/freescale/corenet_ds/ddr.c
new file mode 100644
index 0000000..82b2b4f
--- /dev/null
+++ b/board/freescale/corenet_ds/ddr.c
@@ -0,0 +1,176 @@
+/*
+ * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+static void get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+ int ret;
+
+ ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr3_spd_eeprom_t));
+ if (ret) {
+ debug("DDR: failed to read SPD from address %u\n", i2c_address);
+ memset(spd, 0, sizeof(ddr3_spd_eeprom_t));
+ }
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+ return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd,
+ unsigned int ctrl_num)
+{
+ unsigned int i;
+ unsigned int i2c_address = 0;
+
+ for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+ if (ctrl_num == 0 && i == 0)
+ i2c_address = SPD_EEPROM_ADDRESS1;
+ else if (ctrl_num == 1 && i == 0)
+ i2c_address = SPD_EEPROM_ADDRESS2;
+
+ get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+ }
+}
+
+typedef struct {
+ u32 datarate_mhz_low;
+ u32 datarate_mhz_high;
+ u32 n_ranks;
+ u32 clk_adjust;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2T;
+} board_specific_parameters_t;
+
+/* ranges for parameters:
+ * wr_data_delay = 0-6
+ * clk adjust = 0-8
+ * cpo 2-0x1E (30)
+ */
+
+
+/* XXX: these values need to be checked for all interleaving modes. */
+/* XXX: No reliable dual-rank 800 MHz setting has been found. It may
+ * seem reliable, but errors will appear when memory intensive
+ * program is run. */
+/* XXX: Single rank at 800 MHz is OK. */
+const board_specific_parameters_t board_specific_parameters[][20] = {
+ {
+ /* memory controller 0 */
+ /* lo| hi| num| clk| cpo|wrdata|2T */
+ /* mhz| mhz|ranks|adjst| | delay| */
+ { 0, 333, 2, 6, 7, 3, 0},
+ {334, 400, 2, 6, 9, 3, 0},
+ {401, 549, 2, 6, 11, 3, 0},
+ {550, 680, 2, 1, 10, 5, 0},
+ {681, 850, 2, 1, 12, 5, 0},
+ {851, 1050, 2, 1, 12, 5, 0},
+ {1051, 1250, 2, 1, 15, 4, 0},
+ {1251, 1350, 2, 1, 15, 4, 0},
+ { 0, 333, 1, 6, 7, 3, 0},
+ {334, 400, 1, 6, 9, 3, 0},
+ {401, 549, 1, 6, 11, 3, 0},
+ {550, 680, 1, 1, 10, 5, 0},
+ {681, 850, 1, 1, 12, 5, 0}
+ },
+
+ {
+ /* memory controller 1 */
+ /* lo| hi| num| clk| cpo|wrdata|2T */
+ /* mhz| mhz|ranks|adjst| | delay| */
+ { 0, 333, 2, 6, 7, 3, 0},
+ {334, 400, 2, 6, 9, 3, 0},
+ {401, 549, 2, 6, 11, 3, 0},
+ {550, 680, 2, 1, 11, 6, 0},
+ {681, 850, 2, 1, 13, 6, 0},
+ {851, 1050, 2, 1, 13, 6, 0},
+ {1051, 1250, 2, 1, 15, 4, 0},
+ {1251, 1350, 2, 1, 15, 4, 0},
+ { 0, 333, 1, 6, 7, 3, 0},
+ {334, 400, 1, 6, 9, 3, 0},
+ {401, 549, 1, 6, 11, 3, 0},
+ {550, 680, 1, 1, 11, 6, 0},
+ {681, 850, 1, 1, 13, 6, 0}
+ }
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const board_specific_parameters_t *pbsp =
+ &(board_specific_parameters[ctrl_num][0]);
+ u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
+ sizeof(board_specific_parameters[0][0]);
+ u32 i;
+ ulong ddr_freq;
+
+ /* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
+ * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
+ * there are two dimms in the controller, set odt_rd_cfg to 3 and
+ * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
+ */
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ if (i&1) { /* odd CS */
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 1;
+ } else { /* even CS */
+ if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 1;
+ } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
+ popts->cs_local_opts[i].odt_rd_cfg = 3;
+ popts->cs_local_opts[i].odt_wr_cfg = 3;
+ }
+ }
+ }
+
+ /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ for (i = 0; i < num_params; i++) {
+ if (ddr_freq >= pbsp->datarate_mhz_low &&
+ ddr_freq <= pbsp->datarate_mhz_high &&
+ pdimm->n_ranks == pbsp->n_ranks) {
+ popts->cpo_override = 0xff; /* force auto CPO calibration */
+ popts->write_data_delay = 2;
+ popts->clk_adjust = 5; /* Force value to be 5/8 clock cycle */
+ popts->twoT_en = pbsp->force_2T;
+ }
+ pbsp++;
+ }
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xa;
+ popts->wrlvl_start = 0x7;
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 1;
+ popts->rtt_override_value = DDR3_RTT_120_OHM;
+ popts->rtt_wr_override_value = 0; /* Rtt_WR= dynamic ODT off */
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+}
diff --git a/board/freescale/corenet_ds/law.c b/board/freescale/corenet_ds/law.c
new file mode 100644
index 0000000..43b4b97
--- /dev/null
+++ b/board/freescale/corenet_ds/law.c
@@ -0,0 +1,40 @@
+/*
+ * Copyright 2008-2010 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN),
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN),
+ SET_LAW(PIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/corenet_ds/pci.c b/board/freescale/corenet_ds/pci.c
new file mode 100644
index 0000000..2994e36
--- /dev/null
+++ b/board/freescale/corenet_ds/pci.c
@@ -0,0 +1,127 @@
+/*
+ * Copyright 2007-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+#ifdef CONFIG_PCIE1
+static struct pci_controller pcie1_hose;
+#endif
+
+#ifdef CONFIG_PCIE2
+static struct pci_controller pcie2_hose;
+#endif
+
+#ifdef CONFIG_PCIE3
+static struct pci_controller pcie3_hose;
+#endif
+
+void pci_init_board(void)
+{
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ struct fsl_pci_info pci_info[3];
+ u32 devdisr;
+ int first_free_busno = 0;
+ int num = 0;
+
+ int pcie_ep, pcie_configured;
+
+ devdisr = in_be32(&gur->devdisr);
+
+ debug (" pci_init_board: devdisr=%x\n", devdisr);
+
+#ifdef CONFIG_PCIE1
+ pcie_configured = is_serdes_configured(PCIE1);
+
+ if (pcie_configured && !(devdisr & FSL_CORENET_DEVDISR_PCIE1)) {
+ set_next_law(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_512M,
+ LAW_TRGT_IF_PCIE_1);
+ set_next_law(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_64K,
+ LAW_TRGT_IF_PCIE_1);
+ SET_STD_PCIE_INFO(pci_info[num], 1);
+ pcie_ep = fsl_setup_hose(&pcie1_hose, pci_info[num].regs);
+ printf(" PCIE1 connected to Slot 1 as %s (base addr %lx)\n",
+ pcie_ep ? "End Point" : "Root Complex",
+ pci_info[num].regs);
+ first_free_busno = fsl_pci_init_port(&pci_info[num++],
+ &pcie1_hose, first_free_busno);
+ } else {
+ printf (" PCIE1: disabled\n");
+ }
+#else
+ setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_PCIE1); /* disable */
+#endif
+
+#ifdef CONFIG_PCIE2
+ pcie_configured = is_serdes_configured(PCIE2);
+
+ if (pcie_configured && !(devdisr & FSL_CORENET_DEVDISR_PCIE2)) {
+ set_next_law(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_512M,
+ LAW_TRGT_IF_PCIE_2);
+ set_next_law(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_64K,
+ LAW_TRGT_IF_PCIE_2);
+ SET_STD_PCIE_INFO(pci_info[num], 2);
+ pcie_ep = fsl_setup_hose(&pcie2_hose, pci_info[num].regs);
+ printf(" PCIE2 connected to Slot 3 as %s (base addr %lx)\n",
+ pcie_ep ? "End Point" : "Root Complex",
+ pci_info[num].regs);
+ first_free_busno = fsl_pci_init_port(&pci_info[num++],
+ &pcie2_hose, first_free_busno);
+ } else {
+ printf (" PCIE2: disabled\n");
+ }
+#else
+ setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_PCIE2); /* disable */
+#endif
+
+#ifdef CONFIG_PCIE3
+ pcie_configured = is_serdes_configured(PCIE3);
+
+ if (pcie_configured && !(devdisr & FSL_CORENET_DEVDISR_PCIE3)) {
+ set_next_law(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_512M,
+ LAW_TRGT_IF_PCIE_3);
+ set_next_law(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_64K,
+ LAW_TRGT_IF_PCIE_3);
+ SET_STD_PCIE_INFO(pci_info[num], 3);
+ pcie_ep = fsl_setup_hose(&pcie3_hose, pci_info[num].regs);
+ printf(" PCIE3 connected to Slot 2 as %s (base addr %lx)\n",
+ pcie_ep ? "End Point" : "Root Complex",
+ pci_info[num].regs);
+ first_free_busno = fsl_pci_init_port(&pci_info[num++],
+ &pcie3_hose, first_free_busno);
+ } else {
+ printf (" PCIE3: disabled\n");
+ }
+#else
+ setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_PCIE3); /* disable */
+#endif
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/corenet_ds/tlb.c b/board/freescale/corenet_ds/tlb.c
new file mode 100644
index 0000000..1ae0416
--- /dev/null
+++ b/board/freescale/corenet_ds/tlb.c
@@ -0,0 +1,112 @@
+/*
+ * Copyright 2008-2010 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ SET_TLB_ENTRY(0, PIXIS_BASE, PIXIS_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* *I*G* - Flash, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000,
+ CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000,
+ CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 9, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 11, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 12, BOOKE_PAGESZ_1M, 1),
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 13, BOOKE_PAGESZ_4M, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index b82f530..a70f541 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -343,6 +343,7 @@ MPC8540ADS powerpc mpc85xx mpc8540ads freescale
MPC8544DS powerpc mpc85xx mpc8544ds freescale
MPC8560ADS powerpc mpc85xx mpc8560ads freescale
MPC8568MDS powerpc mpc85xx mpc8568mds freescale
+P4080DS powerpc mpc85xx corenet_ds freescale
XPEDITE5200 powerpc mpc85xx xpedite5200 xes
XPEDITE5370 powerpc mpc85xx xpedite5370 xes
P1022DS powerpc mpc85xx p1022ds freescale
diff --git a/include/configs/P4080DS.h b/include/configs/P4080DS.h
new file mode 100644
index 0000000..43c9a7f
--- /dev/null
+++ b/include/configs/P4080DS.h
@@ -0,0 +1,35 @@
+/*
+ * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * P4080 DS board configuration file
+ */
+#define CONFIG_P4080DS
+#define CONFIG_PHYS_64BIT
+#define CONFIG_PPC_P4080
+#define CONFIG_SYS_NUM_FMAN 2
+#define CONFIG_NUM_DDR_CONTROLLERS 2
+
+#define CONFIG_SYS_P4080_ERRATUM_CPU22
+#define CONFIG_SYS_P4080_ERRATUM_SERDES8
+
+#include "corenet_ds.h"
diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h
new file mode 100644
index 0000000..5f5a175
--- /dev/null
+++ b/include/configs/corenet_ds.h
@@ -0,0 +1,673 @@
+/*
+ * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Corenet DS style board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "../board/freescale/common/ics307_clk.h"
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_E500MC /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */
+#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
+#define CONFIG_MP /* support multiple processors */
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_PCIE2 /* PCIE controler 2 */
+#define CONFIG_PCIE3 /* PCIE controler 3 */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+#define CONFIG_SYS_HAS_SERDES /* has SERDES */
+
+#define CONFIG_SRIO1 /* SRIO port 1 */
+#define CONFIG_SRIO2 /* SRIO port 2 */
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_NOWHERE
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#endif
+
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */
+#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
+#define CONFIG_BTB /* toggle branch predition */
+//#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#endif
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xfe000000 /* relocated CCSRBAR */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS 0xffe000000ull /* physical addr of CCSRBAR */
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#endif
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+#endif
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+#define CONFIG_FSL_DDR3
+
+#ifdef CONFIG_DDR_SPD
+#define CONFIG_SYS_SPD_BUS_NUM 1
+#define SPD_EEPROM_ADDRESS1 0x51
+#define SPD_EEPROM_ADDRESS2 0x52
+#else
+#define CONFIG_SYS_SDRAM_SIZE 4096
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
+#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202
+#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014202
+#define CONFIG_SYS_DDR_TIMING_3 0x01031000
+#define CONFIG_SYS_DDR_TIMING_0 0x55440804
+#define CONFIG_SYS_DDR_TIMING_1 0x74713a66
+#define CONFIG_SYS_DDR_TIMING_2 0x0fb8911b
+#define CONFIG_SYS_DDR_MODE_1 0x00421850
+#define CONFIG_SYS_DDR_MODE_2 0x00100000
+#define CONFIG_SYS_DDR_MODE_CTRL 0x00000000
+#define CONFIG_SYS_DDR_INTERVAL 0x10400100
+#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
+#define CONFIG_SYS_DDR_CLK_CTRL 0x03000000
+#define CONFIG_SYS_DDR_TIMING_4 0x00220001
+#define CONFIG_SYS_DDR_TIMING_5 0x03401500
+#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600
+#define CONFIG_SYS_DDR_WRLVL_CNTL 0x8655a608
+#define CONFIG_SYS_DDR_CONTROL 0xc7048000
+#define CONFIG_SYS_DDR_CONTROL2 0x24400011
+#define CONFIG_SYS_DDR_CDR1 0x00000000
+#define CONFIG_SYS_DDR_CDR2 0x00000000
+#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
+#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
+#define CONFIG_SYS_DDR_SBE 0x00010000
+#define CONFIG_SYS_DDR_DEBUG_18 0x40100400
+
+#define CONFIG_SYS_DDR2_CS0_BNDS 0x008000bf
+#define CONFIG_SYS_DDR2_CS1_BNDS 0x00C000ff
+#define CONFIG_SYS_DDR2_CS0_CONFIG CONFIG_SYS_DDR_CS0_CONFIG
+#define CONFIG_SYS_DDR2_CS1_CONFIG CONFIG_SYS_DDR_CS1_CONFIG
+#define CONFIG_SYS_DDR2_TIMING_3 CONFIG_SYS_DDR_TIMING_3
+#define CONFIG_SYS_DDR2_TIMING_0 CONFIG_SYS_DDR_TIMING_0
+#define CONFIG_SYS_DDR2_TIMING_1 CONFIG_SYS_DDR_TIMING_1
+#define CONFIG_SYS_DDR2_TIMING_2 CONFIG_SYS_DDR_TIMING_2
+#define CONFIG_SYS_DDR2_MODE_1 CONFIG_SYS_DDR_MODE_1
+#define CONFIG_SYS_DDR2_MODE_2 CONFIG_SYS_DDR_MODE_2
+#define CONFIG_SYS_DDR2_MODE_CTRL CONFIG_SYS_DDR_MODE_CTRL
+#define CONFIG_SYS_DDR2_INTERVAL CONFIG_SYS_DDR_INTERVAL
+#define CONFIG_SYS_DDR2_DATA_INIT CONFIG_SYS_DDR_DATA_INIT
+#define CONFIG_SYS_DDR2_CLK_CTRL CONFIG_SYS_DDR_CLK_CTRL
+#define CONFIG_SYS_DDR2_TIMING_4 CONFIG_SYS_DDR_TIMING_4
+#define CONFIG_SYS_DDR2_TIMING_5 CONFIG_SYS_DDR_TIMING_5
+#define CONFIG_SYS_DDR2_ZQ_CNTL CONFIG_SYS_DDR_ZQ_CNTL
+#define CONFIG_SYS_DDR2_WRLVL_CNTL CONFIG_SYS_DDR_WRLVL_CNTL
+#define CONFIG_SYS_DDR2_CONTROL CONFIG_SYS_DDR_CONTROL
+#define CONFIG_SYS_DDR2_CONTROL2 CONFIG_SYS_DDR_CONTROL2
+#define CONFIG_SYS_DDR2_CDR1 CONFIG_SYS_DDR_CDR1
+#define CONFIG_SYS_DDR2_CDR2 CONFIG_SYS_DDR_CDR2
+#define CONFIG_SYS_DDR2_ERR_INT_EN CONFIG_SYS_DDR_ERR_INT_EN
+#define CONFIG_SYS_DDR2_ERR_DIS CONFIG_SYS_DDR_ERR_DIS
+#define CONFIG_SYS_DDR2_SBE CONFIG_SYS_DDR_SBE
+#define CONFIG_SYS_DDR2_DEBUG_18 CONFIG_SYS_DDR_DEBUG_18
+
+#endif
+
+/*
+ * Local Bus Definitions
+ */
+
+/* Set the local bus clock 1/8 of platform clock */
+#define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8
+
+#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* Start of PromJet */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_SYS_BR0_PRELIM \
+ (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \
+ BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR0_PRELIM ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
+ | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)
+
+#define CONFIG_SYS_BR1_PRELIM \
+ (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7
+
+#define CONFIG_FSL_NGPIXIS /* use common ngPIXIS code */
+#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
+#ifdef CONFIG_PHYS_64BIT
+#define PIXIS_BASE_PHYS 0xfffdf0000ull
+#else
+#define PIXIS_BASE_PHYS PIXIS_BASE
+#endif
+
+#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */
+
+#define PIXIS_LBMAP_SWITCH 7
+#define PIXIS_LBMAP_MASK 0xf0
+#define PIXIS_LBMAP_SHIFT 4
+#define PIXIS_LBMAP_ALTBANK 0x40
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x118000
+#define CONFIG_SYS_I2C2_OFFSET 0x118100
+
+/*
+ * RapidIO
+ */
+#define CONFIG_SYS_RIO1_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_RIO1_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_RIO1_MEM_PHYS 0xa0000000
+#endif
+#define CONFIG_SYS_RIO1_MEM_SIZE 0x10000000 /* 256M */
+
+#define CONFIG_SYS_RIO2_MEM_VIRT 0xb0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_RIO2_MEM_PHYS 0xc30000000ull
+#else
+#define CONFIG_SYS_RIO2_MEM_PHYS 0xb0000000
+#endif
+#define CONFIG_SYS_RIO2_MEM_SIZE 0x10000000 /* 256M */
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
+#endif
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xe0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000
+#endif
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
+#else
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
+#endif
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+/* Qman/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 10
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#else
+#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 10
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
+#else
+#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+/* Default address of microcode for the Linux Fman driver */
+#define CONFIG_SYS_FMAN_FW_ADDR 0xEF000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FMAN_FW_ADDR_PHYS 0xFEF000000ULL
+#else
+#define CONFIG_SYS_FMAN_FW_ADDR_PHYS CONFIG_SYS_FMAN_FW_ADDR
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#endif
+
+#ifdef CONFIG_PCI
+
+/*PCIE video card used*/
+#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT
+
+/* video */
+#define CONFIG_VIDEO
+
+#ifdef CONFIG_VIDEO
+#define CONFIG_BIOSEMU
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#endif
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_E1000
+
+#ifndef CONFIG_PCI_PNP
+#define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS
+#define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS
+#define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_PCI */
+
+/* SATA */
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
+
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_FM1_ETH0
+#define CONFIG_SYS_FM1_ETH0_PHY_ADDR 0x1c
+#define CONFIG_SYS_FM1_ETH0_MODE SGMII
+#define CONFIG_FM1_ETH1
+#define CONFIG_SYS_FM1_ETH1_PHY_ADDR 0x1d
+#define CONFIG_SYS_FM1_ETH1_MODE SGMII
+#define CONFIG_FM1_ETH2
+#define CONFIG_SYS_FM1_ETH2_PHY_ADDR 0x1e
+#define CONFIG_SYS_FM1_ETH2_MODE SGMII
+#define CONFIG_FM1_ETH3
+#define CONFIG_SYS_FM1_ETH3_PHY_ADDR 0x1f
+#define CONFIG_SYS_FM1_ETH3_MODE SGMII
+#define CONFIG_FM1_ETH4
+#define CONFIG_SYS_FM1_ETH4_PHY_ADDR 4
+#define CONFIG_SYS_FM1_ETH4_MODE XAUI
+
+#if (CONFIG_SYS_NUM_FMAN == 2)
+#define CONFIG_FM2_ETH0
+#define CONFIG_SYS_FM2_ETH0_PHY_ADDR 0x1c
+#define CONFIG_SYS_FM2_ETH0_MODE SGMII
+#define CONFIG_FM2_ETH1
+#define CONFIG_SYS_FM2_ETH1_PHY_ADDR 0x1d
+#define CONFIG_SYS_FM2_ETH1_MODE SGMII
+#define CONFIG_FM2_ETH2
+#define CONFIG_SYS_FM2_ETH2_PHY_ADDR 0x1e
+#define CONFIG_SYS_FM2_ETH2_MODE SGMII
+#define CONFIG_FM2_ETH3
+#define CONFIG_SYS_FM2_ETH3_PHY_ADDR 0x1f
+#define CONFIG_SYS_FM2_ETH3_MODE SGMII
+#define CONFIG_FM2_ETH4
+#define CONFIG_SYS_FM2_ETH4_PHY_ADDR 0
+#define CONFIG_SYS_FM2_ETH4_MODE XAUI
+#endif
+
+#define CONFIG_SYS_TBIPA_VALUE 8
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1 at DTSEC1"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+* USB
+*/
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH /opt/nfsroot
+#define CONFIG_BOOTFILE uImage
+#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=p4080ds/ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=p4080ds/p4080ds.dtb\0" \
+ "bdev=sda3\0" \
+ "c=ffe\0" \
+ "fman_ucode="MK_STR(CONFIG_SYS_FMAN_FW_ADDR_PHYS)"\0"
+
+#define CONFIG_HDBOOT \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
+
+#endif /* __CONFIG_H */
--
1.6.0.6
More information about the U-Boot
mailing list