[U-Boot] s5pc1xx: Add support for Samsung Goni board

Minkyu Kang mk7.kang at samsung.com
Fri May 28 14:22:17 CEST 2010


This patch adds support for the Samsung Goni board (S5PC110 SoC)

Signed-off-by: Minkyu Kang <mk7.kang at samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
---
 MAINTAINERS                        |    1 +
 MAKEALL                            |    1 +
 Makefile                           |    3 +
 board/samsung/goni/Makefile        |   54 ++++
 board/samsung/goni/config.mk       |   16 +
 board/samsung/goni/goni.c          |   60 ++++
 board/samsung/goni/lowlevel_init.S |  585 ++++++++++++++++++++++++++++++++++++
 board/samsung/goni/mem_setup.S     |  265 ++++++++++++++++
 board/samsung/goni/onenand.c       |   36 +++
 include/configs/s5p_goni.h         |  241 +++++++++++++++
 10 files changed, 1262 insertions(+), 0 deletions(-)
 create mode 100644 board/samsung/goni/Makefile
 create mode 100644 board/samsung/goni/config.mk
 create mode 100644 board/samsung/goni/goni.c
 create mode 100644 board/samsung/goni/lowlevel_init.S
 create mode 100644 board/samsung/goni/mem_setup.S
 create mode 100644 board/samsung/goni/onenand.c
 create mode 100644 include/configs/s5p_goni.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 7f688c3..d00756f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -628,6 +628,7 @@ Simon Kagstrom <simon.kagstrom at netinsight.net>
 Minkyu Kang <mk7.kang at samsung.com>
 
 	SMDKC100	ARM CORTEX-A8 (S5PC100 SoC)
+	s5p_goni	ARM CORTEX-A8 (S5PC110 SoC)
 
 Nishant Kamat <nskamat at ti.com>
 
diff --git a/MAKEALL b/MAKEALL
index 326bde0..f1eefb6 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -649,6 +649,7 @@ LIST_ARM_CORTEX_A8="		\
 	omap3_zoom1		\
 	omap3_zoom2		\
 	smdkc100		\
+	s5p_goni		\
 "
 
 #########################################################################
diff --git a/Makefile b/Makefile
index e49def3..ef37b99 100644
--- a/Makefile
+++ b/Makefile
@@ -3179,6 +3179,9 @@ omap3_zoom2_config :	unconfig
 smdkc100_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 smdkc100 samsung s5pc1xx
 
+s5p_goni_config:	unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 goni samsung s5pc1xx
+
 #########################################################################
 ## XScale Systems
 #########################################################################
diff --git a/board/samsung/goni/Makefile b/board/samsung/goni/Makefile
new file mode 100644
index 0000000..9b4c886
--- /dev/null
+++ b/board/samsung/goni/Makefile
@@ -0,0 +1,54 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# (C) Copyright 2008
+# Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS-y	:= goni.o onenand.o
+SOBJS	:= lowlevel_init.o
+
+SRCS    := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(SOBJS) $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(SOBJS) $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/samsung/goni/config.mk b/board/samsung/goni/config.mk
new file mode 100644
index 0000000..2da9ca1
--- /dev/null
+++ b/board/samsung/goni/config.mk
@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2008 # Samsung Elecgtronics
+# Kyungmin Park <kyungmin.park at samsung.com>
+#
+
+# On S5PC100 we use the 128 MiB OneDRAM bank at
+#
+# 0x30000000 to 0x35000000 (80MiB)
+# 0x38000000 to 0x40000000 (128MiB)
+#
+# On S5PC110 we use the 128 MiB OneDRAM bank at
+#
+# 0x30000000 to 0x35000000 (80MiB)
+# 0x40000000 to 0x50000000 (256MiB)
+#
+TEXT_BASE = 0x34800000
diff --git a/board/samsung/goni/goni.c b/board/samsung/goni/goni.c
new file mode 100644
index 0000000..0defb7b
--- /dev/null
+++ b/board/samsung/goni/goni.c
@@ -0,0 +1,60 @@
+/*
+ *  Copyright (C) 2008-2009 Samsung Electronics
+ *  Minkyu Kang <mk7.kang at samsung.com>
+ *  Kyungmin Park <kyungmin.park at samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+/* Workaround: it will be removed when mach-types is updated */
+#ifndef MACH_TYPE_GONI
+#define MACH_TYPE_GONI	2862
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+	gd->bd->bi_arch_number = MACH_TYPE_GONI;
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
+	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
+
+	return 0;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+	printf("Board:\tGoni\n");
+	return 0;
+}
+#endif
diff --git a/board/samsung/goni/lowlevel_init.S b/board/samsung/goni/lowlevel_init.S
new file mode 100644
index 0000000..4b72992
--- /dev/null
+++ b/board/samsung/goni/lowlevel_init.S
@@ -0,0 +1,585 @@
+/*
+ * Memory Setup stuff - taken from blob memsetup.S
+ *
+ * Copyright (C) 2009 Samsung Electronics
+ * Kyungmin Park <kyungmin.park at samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/power.h>
+
+/*
+ * Register usages:
+ *
+ * r5 has zero always
+ * r7 has S5PC100 GPIO base, 0xE0300000
+ * r8 has real GPIO base, 0xE0300000, 0xE0200000 at S5PC100, S5PC110 repectively
+ * r9 has Mobile DDR size, 1 means 1GiB, 2 means 2GiB and so on
+ */
+
+_TEXT_BASE:
+	.word	TEXT_BASE
+
+	.globl lowlevel_init
+lowlevel_init:
+	mov	r11, lr
+
+	/* r5 has always zero */
+	mov	r5, #0
+
+	ldr	r7, =S5PC100_GPIO_BASE
+	ldr	r8, =S5PC100_GPIO_BASE
+	/* Read CPU ID */
+	ldr	r2, =S5PC1XX_PRO_ID
+	ldr	r0, [r2]
+	mov	r1, #0x00010000
+	and	r0, r0, r1
+	cmp	r0, r5
+	beq	100f
+	ldr	r8, =S5PC110_GPIO_BASE
+100:
+	/* Turn on KEY_LED_ON [GPJ4(1)] XMSMWEN */
+	cmp	r7, r8
+	beq	skip_check_didle			@ Support C110 only
+
+	ldr	r0, =S5PC110_RST_STAT
+	ldr	r1, [r0]
+	and	r1, r1, #0x000D0000
+	cmp	r1, #(0x1 << 19)			@ DEEPIDLE_WAKEUP
+	beq	didle_wakeup
+	cmp	r7, r8
+
+skip_check_didle:
+	addeq	r0, r8, #0x280				@ S5PC100_GPIO_J4
+	addne	r0, r8, #0x2C0				@ S5PC110_GPIO_J4
+	ldr	r1, [r0, #0x0]				@ GPIO_CON_OFFSET
+	bic	r1, r1, #(0xf << 4)			@ 1 * 4-bit
+	orr	r1, r1, #(0x1 << 4)
+	str	r1, [r0, #0x0]				@ GPIO_CON_OFFSET
+
+	ldr	r1, [r0, #0x4]				@ GPIO_DAT_OFFSET
+#ifdef CONFIG_ONENAND_IPL
+	orr	r1, r1, #(1 << 1)			@ 1 * 1-bit
+#else
+	bic	r1, r1, #(1 << 1)
+#endif
+	str	r1, [r0, #0x4]				@ GPIO_DAT_OFFSET
+
+	/* Don't setup at s5pc100 */
+	beq	100f
+
+	/*
+	 * Initialize Async Register Setting for EVT1
+	 * Because we are setting EVT1 as the default value of EVT0,
+	 * setting EVT0 as well does not make things worse.
+	 * Thus, for the simplicity, we set for EVT0, too
+	 *
+	 * The "Async Registers" are:
+	 *	0xE0F0_0000
+	 *	0xE1F0_0000
+	 *	0xF180_0000
+	 *	0xF190_0000
+	 *	0xF1A0_0000
+	 *	0xF1B0_0000
+	 *	0xF1C0_0000
+	 *	0xF1D0_0000
+	 *	0xF1E0_0000
+	 *	0xF1F0_0000
+	 *	0xFAF0_0000
+	 */
+	ldr     r0, =0xe0f00000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	ldr     r0, =0xe1f00000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	ldr     r0, =0xf1800000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	ldr     r0, =0xf1900000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	ldr     r0, =0xf1a00000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	ldr     r0, =0xf1b00000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	ldr     r0, =0xf1c00000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	ldr     r0, =0xf1d00000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	ldr     r0, =0xf1e00000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	ldr     r0, =0xf1f00000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	ldr     r0, =0xfaf00000
+	ldr     r1, [r0]
+	bic     r1, r1, #0x1
+	str     r1, [r0]
+
+	/*
+	 * Diable ABB block to reduce sleep current at low temperature
+	 * Note that it's hidden register setup don't modify it
+	 */
+	ldr	r0, =0xE010C300
+	ldr	r1, =0x00800000
+	str	r1, [r0]
+
+100:
+	/* IO retension release */
+	ldreq	r0, =S5PC100_OTHERS			@ 0xE0108200
+	ldrne	r0, =S5PC110_OTHERS			@ 0xE010E000
+	ldr	r1, [r0]
+	ldreq	r2, =(1 << 31)				@ IO_RET_REL
+	ldrne	r2, =((1 << 31) | (1 << 30) | (1 << 29) | (1 << 28))
+	orr	r1, r1, r2
+	/* Do not release retention here for S5PC110 */
+	streq	r1, [r0]
+
+#ifndef CONFIG_ONENAND_IPL
+	/* Disable Watchdog */
+	ldreq	r0, =S5PC100_WATCHDOG_BASE		@ 0xEA200000
+	ldrne	r0, =S5PC110_WATCHDOG_BASE		@ 0xE2700000
+	str	r5, [r0]
+
+	/* setting SRAM */
+	ldreq	r0, =S5PC100_SROMC_BASE
+	ldrne	r0, =S5PC110_SROMC_BASE
+	ldr	r1, =0x9
+	str	r1, [r0]
+#endif
+
+	/* S5PC100 has 3 groups of interrupt sources */
+	ldreq	r0, =S5PC100_VIC0_BASE			@ 0xE4000000
+	ldrne	r0, =S5PC110_VIC0_BASE			@ 0xF2000000
+	add	r1, r0, #0x00100000
+	add	r2, r0, #0x00200000
+
+	/* Disable all interrupts (VIC0, VIC1 and VIC2) */
+	mvn	r3, #0x0
+	str	r3, [r0, #0x14]				@ INTENCLEAR
+	str	r3, [r1, #0x14]				@ INTENCLEAR
+	str	r3, [r2, #0x14]				@ INTENCLEAR
+
+#ifndef CONFIG_ONENAND_IPL
+	/* Set all interrupts as IRQ */
+	str	r5, [r0, #0xc]				@ INTSELECT
+	str	r5, [r1, #0xc]				@ INTSELECT
+	str	r5, [r2, #0xc]				@ INTSELECT
+
+	/* Pending Interrupt Clear */
+	str	r5, [r0, #0xf00]			@ INTADDRESS
+	str	r5, [r1, #0xf00]			@ INTADDRESS
+	str	r5, [r2, #0xf00]			@ INTADDRESS
+#endif
+
+#ifndef CONFIG_ONENAND_IPL
+	/* for UART */
+	bl	uart_asm_init
+
+	bl	internal_ram_init
+#endif
+
+#ifdef CONFIG_ONENAND_IPL
+	/* init system clock */
+	bl	system_clock_init
+
+	/* OneNAND Sync Read Support at S5PC110 only
+	 * RM[15]	: Sync Read
+	 * BRWL[14:12]	: 7 CLK
+	 * BL[11:9]	: Continuous
+	 * VHF[3]	: Very High Frequency Enable (Over 83MHz)
+	 * HF[2]	: High Frequency Enable (Over 66MHz)
+	 * WM[1]	: Sync Write
+	 */
+	cmp	r7, r8
+	ldrne	r1, =0xE006
+	ldrne	r0, =0xB001E442
+	strneh	r1, [r0]
+
+	/*
+	 * GCE[26]	: Gated Clock Enable
+	 * RPE[17]	: Enables Read Prefetch
+	 */
+	ldrne	r1, =((1 << 26) | (1 << 17) | 0xE006)
+	ldrne	r0, =0xB0600000
+	strne	r1, [r0, #0x100]			@ ONENAND_IF_CTRL
+	ldrne	r1, =0x1212
+	strne	r1, [r0, #0x108]
+
+	/* Board detection to set proper memory configuration */
+	cmp	r7, r8
+	moveq	r9, #1		/* r9 has 1Gib default at s5pc100 */
+	movne	r9, #2		/* r9 has 2Gib default at s5pc110 */
+
+	ldr	r2, =0xE0200200
+	ldr	r4, [r2, #0x48]
+
+	bic	r1, r4, #(0x3F << 4)	/* PULLUP_DISABLE: 3 * 2-bit */
+	bic	r1, r1, #(0x3 << 2)	/* PULLUP_DISABLE: 2 * 2-bit */
+	bic	r1, r1, #(0x3 << 14)	/* PULLUP_DISABLE: 2 * 2-bit */
+	str	r1, [r2, #0x48]
+	/* For write completion */
+	nop
+	nop
+
+	ldr	r3, [r2, #0x44]
+	and	r1, r3, #(0x7 << 2)
+	mov	r1, r1, lsr #2
+	cmp	r1, #0x5
+	moveq	r9, #3
+	cmp	r1, #0x6
+	moveq	r9, #1
+	cmp	r1, #0x7
+	moveq	r9, #2
+	and	r0, r3, #(0x1 << 1)
+	mov	r0, r0, lsr #1
+	orr	r1, r1, r0, lsl #3
+	cmp	r1, #0x8
+	moveq	r9, #3
+	and	r1, r3, #(0x7 << 2)
+	mov	r1, r1, lsr #2
+	and	r0, r3, #(0x1 << 7)
+	mov	r0, r0, lsr #7
+	orr	r1, r1, r0, lsl #3
+	cmp	r1, #0x9
+	moveq	r9, #3
+	str	r4, [r2, #0x48]		/* Restore PULLUP configuration */
+
+	bl	mem_ctrl_asm_init
+
+	/* Wakeup support. Don't know if it's going to be used, untested. */
+	ldreq	r0, =S5PC100_RST_STAT
+	ldrne	r0, =S5PC110_RST_STAT
+	ldr	r1, [r0]
+	biceq	r1, r1, #0xfffffff7
+	moveq	r2, #(1 << 3)
+	bicne	r1, r1, #0xfffeffff
+	movne	r2, #(1 << 16)
+	cmp	r1, r2
+	bne	1f
+wakeup:
+	/* turn off L2 cache */
+	bl	l2_cache_disable
+
+	cmp	r7, r8
+	ldreq	r0, =0xC100
+	ldrne	r0, =0xC110
+
+	/* invalidate L2 cache also */
+	bl	invalidate_dcache
+
+	/* turn on L2 cache */
+	bl	l2_cache_enable
+
+	cmp	r7, r8
+	/* Load return address and jump to kernel */
+	ldreq	r0, =S5PC100_INFORM0
+	ldrne	r0, =S5PC110_INFORM0
+
+	/* r1 = physical address of s5pc1xx_cpu_resume function */
+	ldr	r1, [r0]
+
+	/* Jump to kernel (sleep-s5pc1xx.S) */
+	mov	pc, r1
+	nop
+	nop
+#else
+	cmp	r7, r8
+	/* Clear wakeup status register */
+	ldreq	r0, =S5PC100_WAKEUP_STAT
+	ldrne	r0, =S5PC110_WAKEUP_STAT
+	ldr	r1, [r0]
+	str	r1, [r0]
+
+	/* IO retension release */
+	ldreq	r0, =S5PC100_OTHERS			@ 0xE0108200
+	ldrne	r0, =S5PC110_OTHERS			@ 0xE010E000
+	ldr	r1, [r0]
+	ldreq	r2, =(1 << 31)				@ IO_RET_REL
+	ldrne	r2, =((1 << 31) | (1 << 30) | (1 << 29) | (1 << 28))
+	orr	r1, r1, r2
+	str	r1, [r0]
+
+#endif
+	b	1f
+
+didle_wakeup:
+	/* Wait when APLL is locked */
+	ldr	r0, =0xE0100100			@ S5PC110_APLL_CON
+lockloop:
+	ldr	r1, [r0]
+	and	r1, r1, #(1 << 29)
+	cmp	r1, #(1 << 29)
+	bne	lockloop
+
+	ldr	r0, =S5PC110_INFORM0
+	ldr	r1, [r0]
+	mov	pc, r1
+	nop
+	nop
+	nop
+	nop
+	nop
+
+1:
+	mov	lr, r11
+	mov	pc, lr
+
+/*
+ * system_clock_init: Initialize core clock and bus clock.
+ * void system_clock_init(void)
+ */
+system_clock_init:
+	ldr	r0, =S5PC1XX_CLOCK_BASE		@ 0xE0100000
+
+	/* Check S5PC100 */
+	cmp	r7, r8
+	bne	110f
+100:
+	/* Set Lock Time */
+	ldr	r1, =0xe10			@ Locktime : 0xe10 = 3600
+	str	r1, [r0, #0x000]		@ S5PC100_APLL_LOCK
+	str	r1, [r0, #0x004]		@ S5PC100_MPLL_LOCK
+	str	r1, [r0, #0x008]		@ S5PC100_EPLL_LOCK
+	str	r1, [r0, #0x00C]		@ S5PC100_HPLL_LOCK
+
+	/* S5P_APLL_CON */
+	ldr	r1, =0x81bc0400		@ SDIV 0, PDIV 4, MDIV 444 (1333MHz)
+	str	r1, [r0, #0x100]
+	/* S5P_MPLL_CON */
+	ldr	r1, =0x80590201		@ SDIV 1, PDIV 2, MDIV 89 (267MHz)
+	str	r1, [r0, #0x104]
+	/* S5P_EPLL_CON */
+	ldr	r1, =0x80870303		@ SDIV 3, PDIV 3, MDIV 135 (67.5MHz)
+	str	r1, [r0, #0x108]
+	/* S5P_HPLL_CON */
+	ldr	r1, =0x80600603		@ SDIV 3, PDIV 6, MDIV 96
+	str	r1, [r0, #0x10C]
+
+	ldr     r1, [r0, #0x300]
+	ldr     r2, =0x00003fff
+	bic     r1, r1, r2
+	ldr     r2, =0x00011301
+
+	orr	r1, r1, r2
+	str	r1, [r0, #0x300]
+	ldr     r1, [r0, #0x304]
+	ldr     r2, =0x00011110
+	orr     r1, r1, r2
+	str     r1, [r0, #0x304]
+	ldr     r1, =0x00000001
+	str     r1, [r0, #0x308]
+
+	/* Set Source Clock */
+	ldr	r1, =0x00001111			@ A, M, E, HPLL Muxing
+	str	r1, [r0, #0x200]		@ S5PC1XX_CLK_SRC0
+
+	b	200f
+110:
+	ldr	r0, =0xE010C000			@ S5PC110_PWR_CFG
+
+	/* Set OSC_FREQ value */
+	ldr	r1, =0xf
+	str	r1, [r0, #0x100]		@ S5PC110_OSC_FREQ
+
+	/* Set MTC_STABLE value */
+	ldr	r1, =0xffffffff
+	str	r1, [r0, #0x110]		@ S5PC110_MTC_STABLE
+
+	/* Set CLAMP_STABLE value */
+	ldr	r1, =0x3ff03ff
+	str	r1, [r0, #0x114]		@ S5PC110_CLAMP_STABLE
+
+	ldr	r0, =S5PC1XX_CLOCK_BASE		@ 0xE0100000
+
+	/* Set Clock divider */
+	ldr	r1, =0x14131330			@ 1:1:4:4, 1:4:5
+	str	r1, [r0, #0x300]
+	ldr	r1, =0x11110111			@ UART[3210]: MMC[3210]
+	str	r1, [r0, #0x310]
+
+	/* Set Lock Time */
+	ldr	r1, =0x2cf			@ Locktime : 30us
+	str	r1, [r0, #0x000]		@ S5PC110_APLL_LOCK
+	ldr	r1, =0xe10			@ Locktime : 0xe10 = 3600
+	str	r1, [r0, #0x008]		@ S5PC110_MPLL_LOCK
+	str	r1, [r0, #0x010]		@ S5PC110_EPLL_LOCK
+	str	r1, [r0, #0x020]		@ S5PC110_VPLL_LOCK
+
+	/* S5PC110_APLL_CON */
+	ldr	r1, =0x80C80601			@ 800MHz
+	str	r1, [r0, #0x100]
+	/* S5PC110_MPLL_CON */
+	ldr	r1, =0x829B0C01			@ 667MHz
+	str	r1, [r0, #0x108]
+	/* S5PC110_EPLL_CON */
+	ldr	r1, =0x80600602			@  96MHz VSEL 0 P 6 M 96 S 2
+	str	r1, [r0, #0x110]
+	/* S5PC110_VPLL_CON */
+	ldr	r1, =0x806C0603			@  54MHz
+	str	r1, [r0, #0x120]
+
+	/* Set Source Clock */
+	ldr	r1, =0x10001111			@ A, M, E, VPLL Muxing
+	str	r1, [r0, #0x200]		@ S5PC1XX_CLK_SRC0
+
+	/* OneDRAM(DMC0) clock setting */
+	ldr	r1, =0x01000000			@ ONEDRAM_SEL[25:24] 1 SCLKMPLL
+	str	r1, [r0, #0x218]		@ S5PC110_CLK_SRC6
+	ldr	r1, =0x30000000			@ ONEDRAM_RATIO[31:28] 3 + 1
+	str	r1, [r0, #0x318]		@ S5PC110_CLK_DIV6
+
+	/* XCLKOUT = XUSBXTI 24MHz */
+	add	r2, r0, #0xE000			@ S5PC110_OTHERS
+	ldr     r1, [r2]
+	orr	r1, r1, #(0x3 << 8)		@ CLKOUT[9:8] 3 XUSBXTI
+	str	r1, [r2]
+
+	/* CLK_IP0 */
+	ldr	r1, =0x8fefeeb			@ DMC[1:0] PDMA0[3] IMEM[5]
+	str	r1, [r0, #0x460]		@ S5PC110_CLK_IP0
+
+	/* CLK_IP1 */
+	ldr	r1, =0xe9fdf0f9			@ FIMD[0] USBOTG[16]
+						@ NANDXL[24]
+	str	r1, [r0, #0x464]		@ S5PC110_CLK_IP1
+
+	/* CLK_IP2 */
+	ldr	r1, =0xf75f7fc			@ CORESIGHT[8] MODEM[9]
+						@ HOSTIF[10] HSMMC0[16]
+						@ HSMMC2[18] VIC[27:24]
+	str	r1, [r0, #0x468]		@ S5PC110_CLK_IP2
+
+	/* CLK_IP3 */
+	ldr	r1, =0x8eff038c			@ I2C[8:6]
+						@ SYSTIMER[16] UART0[17]
+						@ UART1[18] UART2[19]
+						@ UART3[20] WDT[22]
+						@ PWM[23] GPIO[26] SYSCON[27]
+	str	r1, [r0, #0x46c]		@ S5PC110_CLK_IP3
+
+	/* CLK_IP4 */
+	ldr	r1, =0xfffffff1			@ CHIP_ID[0] TZPC[8:5]
+	str	r1, [r0, #0x470]		@ S5PC110_CLK_IP3
+
+200:
+	/* wait at least 200us to stablize all clock */
+	mov	r2, #0x10000
+1:	subs	r2, r2, #1
+	bne	1b
+
+	mov	pc, lr
+
+#ifndef CONFIG_ONENAND_IPL
+internal_ram_init:
+	ldreq	r0, =0xE3800000
+	ldrne	r0, =0xF1500000
+	ldr	r1, =0x0
+	str	r1, [r0]
+
+	mov	pc, lr
+#endif
+
+#ifndef CONFIG_ONENAND_IPL
+/*
+ * uart_asm_init: Initialize UART's pins
+ */
+uart_asm_init:
+	/* set GPIO to enable UART0-UART4 */
+	mov	r0, r8
+	ldr	r1, =0x22222222
+	str	r1, [r0, #0x0]			@ S5PC100_GPIO_A0_OFFSET
+	ldr	r1, =0x00002222
+	str	r1, [r0, #0x20]			@ S5PC100_GPIO_A1_OFFSET
+
+	/* Check S5PC100 */
+	cmp	r7, r8
+	bne	110f
+
+	/* UART_SEL GPK0[5] at S5PC100 */
+	add	r0, r8, #0x2A0			@ S5PC100_GPIO_K0_OFFSET
+	ldr	r1, [r0, #0x0]			@ S5PC1XX_GPIO_CON_OFFSET
+	bic	r1, r1, #(0xf << 20)		@ 20 = 5 * 4-bit
+	orr	r1, r1, #(0x1 << 20)		@ Output
+	str	r1, [r0, #0x0]			@ S5PC1XX_GPIO_CON_OFFSET
+
+	ldr	r1, [r0, #0x8]			@ S5PC1XX_GPIO_PULL_OFFSET
+	bic	r1, r1, #(0x3 << 10)		@ 10 = 5 * 2-bit
+	orr	r1, r1, #(0x2 << 10)		@ Pull-up enabled
+	str	r1, [r0, #0x8]			@ S5PC1XX_GPIO_PULL_OFFSET
+
+	ldr	r1, [r0, #0x4]			@ S5PC1XX_GPIO_DAT_OFFSET
+	orr	r1, r1, #(1 << 5)		@ 5 = 5 * 1-bit
+	str	r1, [r0, #0x4]			@ S5PC1XX_GPIO_DAT_OFFSET
+
+	b	200f
+110:
+	/*
+	 * Note that the following address
+	 * 0xE020'0360 is reserved address at S5PC100
+	 */
+	/* UART_SEL MP0_5[7] at S5PC110 */
+	add	r0, r8, #0x360			@ S5PC110_GPIO_MP0_5_OFFSET
+	ldr	r1, [r0, #0x0]			@ S5PC1XX_GPIO_CON_OFFSET
+	bic	r1, r1, #(0xf << 28)		@ 28 = 7 * 4-bit
+	orr	r1, r1, #(0x1 << 28)		@ Output
+	str	r1, [r0, #0x0]			@ S5PC1XX_GPIO_CON_OFFSET
+
+	ldr	r1, [r0, #0x8]			@ S5PC1XX_GPIO_PULL_OFFSET
+	bic	r1, r1, #(0x3 << 14)		@ 14 = 7 * 2-bit
+	orr	r1, r1, #(0x2 << 14)		@ Pull-up enabled
+	str	r1, [r0, #0x8]			@ S5PC1XX_GPIO_PULL_OFFSET
+
+	ldr	r1, [r0, #0x4]			@ S5PC1XX_GPIO_DAT_OFFSET
+	orr	r1, r1, #(1 << 7)		@ 7 = 7 * 1-bit
+	str	r1, [r0, #0x4]			@ S5PC1XX_GPIO_DAT_OFFSET
+200:
+	mov	pc, lr
+#endif
diff --git a/board/samsung/goni/mem_setup.S b/board/samsung/goni/mem_setup.S
new file mode 100644
index 0000000..c4d2845
--- /dev/null
+++ b/board/samsung/goni/mem_setup.S
@@ -0,0 +1,265 @@
+/*
+ * Copyright (C) 2009 Samsung Electrnoics
+ * Minkyu Kang <mk7.kang at samsung.com>
+ * Kyungmin Park <kyungmin.park at samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+
+	.globl mem_ctrl_asm_init
+mem_ctrl_asm_init:
+	cmp	r7, r8
+
+	ldreq	r0, =S5PC100_DMC_BASE			@ 0xE6000000
+	ldrne	r0, =S5PC110_DMC0_BASE			@ 0xF0000000
+	ldrne	r6, =S5PC110_DMC1_BASE			@ 0xF1400000
+
+	/* DLL parameter setting */
+	ldr	r1, =0x50101000
+	str	r1, [r0, #0x018]			@ PHYCONTROL0_OFFSET
+	strne	r1, [r6, #0x018]			@ PHYCONTROL0_OFFSET
+	ldr	r1, =0x000000f4
+	str	r1, [r0, #0x01C]			@ PHYCONTROL1_OFFSET
+	strne	r1, [r6, #0x01C]			@ PHYCONTROL1_OFFSET
+	ldreq	r1, =0x0
+	streq	r1, [r0, #0x020]			@ PHYCONTROL2_OFFSET
+
+	/* DLL on */
+	ldr	r1, =0x50101002
+	str	r1, [r0, #0x018]			@ PHYCONTROL0_OFFSET
+	strne	r1, [r6, #0x018]			@ PHYCONTROL0_OFFSET
+
+	/* DLL start */
+	ldr	r1, =0x50101003
+	str	r1, [r0, #0x018]			@ PHYCONTROL0_OFFSET
+	strne	r1, [r6, #0x018]			@ PHYCONTROL0_OFFSET
+
+	mov	r2, #0x4000
+wait:	subs	r2, r2, #0x1
+	cmp	r2, #0x0
+	bne	wait
+
+	cmp	r7, r8
+	/* Force value locking for DLL off */
+	str	r1, [r0, #0x018]			@ PHYCONTROL0_OFFSET
+	strne	r1, [r6, #0x018]			@ PHYCONTROL0_OFFSET
+
+	/* DLL off */
+	ldr	r1, =0x50101009
+	str	r1, [r0, #0x018]			@ PHYCONTROL0_OFFSET
+	strne	r1, [r6, #0x018]			@ PHYCONTROL0_OFFSET
+
+	/* auto refresh off */
+	ldr	r1, =0xff001010 | (1 << 7)
+	ldr	r2, =0xff001010 | (1 << 7)
+	str	r1, [r0, #0x000]			@ CONCONTROL_OFFSET
+	strne	r2, [r6, #0x000]			@ CONCONTROL_OFFSET
+
+	/*
+	 * Burst Length 4, 2 chips, 32-bit, LPDDR
+	 * OFF: dynamic self refresh, force precharge, dynamic power down off
+	 */
+	ldr	r1, =0x00212100
+	ldr	r2, =0x00212100
+	str	r1, [r0, #0x004]			@ MEMCONTROL_OFFSET
+	strne	r2, [r6, #0x004]			@ MEMCONTROL_OFFSET
+
+	/*
+	 * Note:
+	 * If Bank0 has Mobile RAM we place it at 0x3800'0000 (s5pc100 only)
+	 * So finally Bank1 OneDRAM should address start at at 0x3000'0000
+	 */
+
+	/*
+	 * DMC0: CS0 : S5PC100/S5PC110
+	 * 0x30 -> 0x30000000
+	 * 0xf8 -> 0x37FFFFFF
+	 * [15:12] 0: Linear
+	 * [11:8 ] 2: 9 bits
+	 * [ 7:4 ] 2: 14 bits
+	 * [ 3:0 ] 2: 4 banks
+	 */
+	ldr	r3, =0x30f80222
+	ldr	r4, =0x40f00222
+swap_memory:
+	str	r3, [r0, #0x008]			@ MEMCONFIG0_OFFSET
+	str	r4, [r0, #0x00C]			@ dummy write
+
+	/*
+	 * DMC1: CS0 : S5PC110
+	 * 0x40 -> 0x40000000
+	 * 0xf8 -> 0x47FFFFFF (1Gib)
+	 * 0x40 -> 0x40000000
+	 * 0xf0 -> 0x4FFFFFFF (2Gib)
+	 * [15:12] 0: Linear
+	 * [11:8 ] 2: 9 bits  - Col (1Gib)
+	 * [11:8 ] 3: 10 bits - Col (2Gib)
+	 * [ 7:4 ] 2: 14 bits - Row
+	 * [ 3:0 ] 2: 4 banks
+	 */
+	/* Default : 2GiB */
+	ldr	r4, =0x40f01322				@ 2Gib: MCP B
+	ldr	r5, =0x50f81312				@ dummy: MCP D
+	cmp	r9, #1
+	ldreq	r4, =0x40f81222				@ 1Gib: MCP A
+	cmp	r9, #3
+	ldreq	r5, =0x50f81312				@ 2Gib + 1Gib: MCP D
+	cmp	r9, #4
+	ldreq	r5, =0x50f01312				@ 2Gib + 2Gib: MCP E
+
+	cmp	r7, r8
+	strne	r4, [r6, #0x008]			@ MEMCONFIG0_OFFSET
+	strne	r5, [r6, #0x00C]			@ MEMCONFIG1_OFFSET
+
+	/*
+	 * DMC0: CS1: S5PC100
+	 * 0x38 -> 0x38000000
+	 * 0xf8 -> 0x3fFFFFFF
+	 * [15:12] 0: Linear
+	 * [11:8 ] 2: 9 bits
+	 * [ 7:4 ] 2: 14 bits
+	 * [ 3:0 ] 2: 4 banks
+	 */
+	eoreq	r3, r3, #0x08000000
+	streq	r3, [r0, #0xc]				@ MEMCONFIG1_OFFSET
+
+	ldr	r1, =0x20000000
+	str	r1, [r0, #0x014]			@ PRECHCONFIG_OFFSET
+	strne	r1, [r0, #0x014]			@ PRECHCONFIG_OFFSET
+	strne	r1, [r6, #0x014]			@ PRECHCONFIG_OFFSET
+
+	/*
+	 * S5PC100:
+	 * DMC:  CS0: 166MHz
+	 *       CS1: 166MHz
+	 * S5PC110:
+	 * DMC0: CS0: 166MHz
+	 * DMC1: CS0: 200MHz
+	 *
+	 * 7.8us * 200MHz %LE %LONG1560(0x618)
+	 * 7.8us * 166MHz %LE %LONG1294(0x50E)
+	 * 7.8us * 133MHz %LE %LONG1038(0x40E),
+	 * 7.8us * 100MHz %LE %LONG780(0x30C),
+	 */
+	ldr	r1, =0x0000050E
+	str	r1, [r0, #0x030]			@ TIMINGAREF_OFFSET
+	ldrne	r1, =0x00000618
+	strne	r1, [r6, #0x030]			@ TIMINGAREF_OFFSET
+
+	ldr	r1, =0x14233287
+	str	r1, [r0, #0x034]			@ TIMINGROW_OFFSET
+	ldrne	r1, =0x182332c8
+	strne	r1, [r6, #0x034]			@ TIMINGROW_OFFSET
+
+	ldr	r1, =0x12130005
+	str	r1, [r0, #0x038]			@ TIMINGDATA_OFFSET
+	ldrne	r1, =0x13130005
+	strne	r1, [r6, #0x038]			@ TIMINGDATA_OFFSET
+
+	ldr	r1, =0x0E140222
+	str	r1, [r0, #0x03C]			@ TIMINGPOWER_OFFSET
+	ldrne	r1, =0x0E180222
+	strne	r1, [r6, #0x03C]			@ TIMINGPOWER_OFFSET
+
+	/* chip0 Deselect */
+	ldr	r1, =0x07000000
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+
+	/* chip0 PALL */
+	ldr	r1, =0x01000000
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+
+	/* chip0 REFA */
+	ldr	r1, =0x05000000
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+	/* chip0 REFA */
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+
+	/* chip0 MRS */
+	ldr	r1, =0x00000032
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+
+	/* chip0 EMRS */
+	ldr	r1, =0x00020020
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+
+	/* chip1 Deselect */
+	ldr	r1, =0x07100000
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+
+	/* chip1 PALL */
+	ldr	r1, =0x01100000
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+
+	/* chip1 REFA */
+	ldr	r1, =0x05100000
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+	/* chip1 REFA */
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+
+	/* chip1 MRS */
+	ldr	r1, =0x00100032
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+
+	/* chip1 EMRS */
+	ldr	r1, =0x00120020
+	str	r1, [r0, #0x010]			@ DIRECTCMD_OFFSET
+	strne	r1, [r6, #0x010]			@ DIRECTCMD_OFFSET
+
+	/* auto refresh on */
+	ldr	r1, =0xFF002030 | (1 << 7)
+	str	r1, [r0, #0x000]			@ CONCONTROL_OFFSET
+	strne	r1, [r6, #0x000]			@ CONCONTROL_OFFSET
+
+	/* PwrdnConfig */
+	ldr	r1, =0x00100002
+	str	r1, [r0, #0x028]			@ PWRDNCONFIG_OFFSET
+	strne	r1, [r6, #0x028]			@ PWRDNCONFIG_OFFSET
+
+	ldr	r1, =0x00212113
+	str	r1, [r0, #0x004]			@ MEMCONTROL_OFFSET
+	strne	r1, [r6, #0x004]			@ MEMCONTROL_OFFSET
+
+	/* Skip when S5PC110 */
+	bne	1f
+
+	/* Check OneDRAM access area at s5pc100 */
+	ldreq	r3, =0x38f80222
+	ldreq	r1, =0x37ffff00
+	str	r3, [r1]
+	ldr	r2, [r1]
+	cmp	r2, r3
+	beq	swap_memory
+1:
+	mov	pc, lr
+
+	.ltorg
diff --git a/board/samsung/goni/onenand.c b/board/samsung/goni/onenand.c
new file mode 100644
index 0000000..8d3769b
--- /dev/null
+++ b/board/samsung/goni/onenand.c
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2008-2009 Samsung Electronics
+ * Kyungmin Park <kyungmin.park at samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+#include <linux/mtd/samsung_onenand.h>
+#include <onenand_uboot.h>
+
+void onenand_board_init(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	this->base = (void *)CONFIG_SYS_ONENAND_BASE;
+	this->options |= ONENAND_RUNTIME_BADBLOCK_CHECK;
+}
diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h
new file mode 100644
index 0000000..4f6b798
--- /dev/null
+++ b/include/configs/s5p_goni.h
@@ -0,0 +1,241 @@
+/*
+ * Copyright (C) 2009 Samsung Electronics
+ * Minkyu Kang <mk7.kang at samsung.com>
+ * Kyungmin Park <kyungmin.park at samsung.com>
+ *
+ * Configuation settings for the SAMSUNG Universal (s5pc100) board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_ARMCORTEXA8	1	/* This is an ARM V7 CPU core */
+#define CONFIG_SAMSUNG		1	/* in a SAMSUNG core */
+#define CONFIG_S5PC1XX		1	/* which is in a S5PC1XX Family */
+#define CONFIG_S5PC110		1	/* which is in a S5PC110 */
+#define CONFIG_MACH_GONI	1	/* working with Goni */
+
+#include <asm/arch/cpu.h>		/* get chip and board defs */
+
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+
+/* input clock of PLL: has 24MHz input clock at S5PC110 */
+#define CONFIG_SYS_CLK_FREQ_C110	24000000
+
+/* DRAM Base */
+#define CONFIG_SYS_SDRAM_BASE		0x30000000
+
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_EDITING
+
+/*
+ * Size of malloc() pool
+ * 1MB = 0x100000, 0x100000 = 1024 * 1024
+ */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (1 << 20))
+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes for */
+						/* initial data */
+/*
+ * select serial console configuration
+ */
+#define CONFIG_SERIAL2			1	/* use SERIAL2 */
+#define CONFIG_SERIAL_MULTI		1
+#define CONFIG_BAUDRATE			115200
+
+/* It should define before config_cmd_default.h */
+#define CONFIG_SYS_NO_FLASH		1
+/***********************************************************
+ * Command definition
+ ***********************************************************/
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_BOOTD
+#undef CONFIG_CMD_CONSOLE
+#undef CONFIG_CMD_ECHO
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_ITEST
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_NAND
+#undef CONFIG_CMD_MISC
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_SOURCE
+#undef CONFIG_CMD_XIMG
+#undef CONFIG_CMD_NET
+#undef CONFIG_XYZMODEM
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_ONENAND
+#define CONFIG_CMD_MTDPARTS
+
+#define CONFIG_BOOTDELAY		1
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+
+/* Actual modem binary size is 16MiB. Add 2MiB for bad block handling */
+#define MTDIDS_DEFAULT		"onenand0=samsung-onenand"
+#define MTDPARTS_DEFAULT	"mtdparts=samsung-onenand:1m(bootloader)"\
+				",256k(params)"\
+				",2816k(config)"\
+				",8m(csa)"\
+				",7m(kernel)"\
+				",1m(log)"\
+				",12m(modem)"\
+				",60m(qboot)"\
+				",-(UBI)\0"
+
+#define NORMAL_MTDPARTS_DEFAULT MTDPARTS_DEFAULT
+
+#define CONFIG_BOOTCOMMAND	"run ubifsboot"
+
+#define CONFIG_DEFAULT_CONSOLE	"console=ttySAC2,115200n8\0"
+
+#define CONFIG_RAMDISK_BOOT	"root=/dev/ram0 rw rootfstype=ext2" \
+		" ${console} ${meminfo}"
+
+#define CONFIG_COMMON_BOOT	"${console} ${meminfo} ${mtdparts}"
+
+#define CONFIG_BOOTARGS	"root=/dev/mtdblock8 ubi.mtd=8 ubi.mtd=3 ubi.mtd=6" \
+		" rootfstype=cramfs " CONFIG_COMMON_BOOT
+
+#define CONFIG_UPDATEB	"updateb=onenand erase 0x0 0x100000;" \
+			" onenand write 0x32008000 0x0 0x100000\0"
+
+#define CONFIG_UBI_MTD	" ubi.mtd=${ubiblock} ubi.mtd=3 ubi.mtd=6"
+
+#define CONFIG_UBIFS_OPTION	"rootflags=bulk_read,no_chk_data_crc"
+
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	CONFIG_UPDATEB \
+	"updatek=" \
+		"onenand erase 0xc00000 0x600000;" \
+		"onenand write 0x31008000 0xc00000 0x600000\0" \
+	"updateu=" \
+		"onenand erase 0x01560000 0x1eaa0000;" \
+		"onenand write 0x32000000 0x1260000 0x8C0000\0" \
+	"bootk=" \
+		"onenand read 0x30007FC0 0xc00000 0x600000;" \
+		"bootm 0x30007FC0\0" \
+	"flashboot=" \
+		"set bootargs root=/dev/mtdblock${bootblock} " \
+		"rootfstype=${rootfstype}" CONFIG_UBI_MTD " ${opts} " \
+		"${lcdinfo} " CONFIG_COMMON_BOOT "; run bootk\0" \
+	"ubifsboot=" \
+		"set bootargs root=ubi0!rootfs rootfstype=ubifs " \
+		CONFIG_UBIFS_OPTION CONFIG_UBI_MTD " ${opts} ${lcdinfo} " \
+		CONFIG_COMMON_BOOT "; run bootk\0" \
+	"tftpboot=" \
+		"set bootargs root=ubi0!rootfs rootfstype=ubifs " \
+		CONFIG_UBIFS_OPTION CONFIG_UBI_MTD " ${opts} ${lcdinfo} " \
+		CONFIG_COMMON_BOOT "; tftp 0x30007FC0 uImage; " \
+		"bootm 0x30007FC0\0" \
+	"ramboot=" \
+		"set bootargs " CONFIG_RAMDISK_BOOT \
+		" initrd=0x33000000,8M ramdisk=8192\0" \
+	"mmcboot=" \
+		"set bootargs root=${mmcblk} rootfstype=${rootfstype}" \
+		CONFIG_UBI_MTD " ${opts} ${lcdinfo} " \
+		CONFIG_COMMON_BOOT "; run bootk\0" \
+	"boottrace=setenv opts initcall_debug; run bootcmd\0" \
+	"bootchart=set opts init=/sbin/bootchartd; run bootcmd\0" \
+	"verify=n\0" \
+	"rootfstype=cramfs\0" \
+	"console=" CONFIG_DEFAULT_CONSOLE \
+	"mtdparts=" MTDPARTS_DEFAULT \
+	"meminfo=mem=80M mem=256M at 0x40000000 mem=128M at 0x50000000\0" \
+	"mmcblk=/dev/mmcblk1p1\0" \
+	"bootblock=9\0" \
+	"ubiblock=8\0" \
+	"ubi=enabled\0" \
+	"opts=always_resume=1"
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_PROMPT	"Goni # "
+#define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE	384	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x5000000)
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x4000000)
+
+#define CONFIG_SYS_HZ			1000
+
+/* valid baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE	(256 << 10)	/* 256 KiB */
+
+/* Goni has 2 banks of DRAM, but swap the bank */
+#define CONFIG_NR_DRAM_BANKS	3
+#define PHYS_SDRAM_1		CONFIG_SYS_SDRAM_BASE	/* OneDRAM Bank #0 */
+#define PHYS_SDRAM_1_SIZE	(80 << 20)		/* 80 MB in Bank #0 */
+#define PHYS_SDRAM_2		0x40000000		/* mDDR DMC1 Bank #1 */
+#define PHYS_SDRAM_2_SIZE	(256 << 20)		/* 256 MB in Bank #1 */
+#define PHYS_SDRAM_3		0x50000000		/* mDDR DMC1 Bank #1 */
+#define PHYS_SDRAM_3_SIZE	(128 << 20)		/* 256 MB in Bank #1 */
+
+#define CONFIG_SYS_MONITOR_BASE		0x00000000
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* 256 KiB */
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+#define CONFIG_ENV_IS_IN_ONENAND	1
+#define CONFIG_ENV_SIZE			(256 << 10)	/* 256 KiB, 0x40000 */
+#define CONFIG_ENV_ADDR			(1 << 20)	/* 1 MB, 0x100000 */
+
+#define CONFIG_USE_ONENAND_BOARD_INIT
+#define CONFIG_SAMSUNG_ONENAND		1
+#define CONFIG_SYS_ONENAND_BASE		0xB0000000
+
+#define CONFIG_DOS_PARTITION		1
+
+#endif	/* __CONFIG_H */
-- 
1.6.3.3


More information about the U-Boot mailing list