[U-Boot] [PATCH V2] mvsata_ide: adjust port init sequence
Albert Aribaud
albert.aribaud at free.fr
Tue Sep 7 01:02:31 CEST 2010
mvsata_ide_initialize_port(): adjust init sequence (SStatus
should be checked only after all writes to SControl) and
return success/failure to ide_preinit().
Also, as some tests showed init durations in the hundreds
of us, raise the time-out to 10 ms to be on the safe side.
Signed-off-by: Albert Aribaud <albert.aribaud at free.fr>
---
PATCH HISTORY
V1 Initial patch.
V2 Fixed wrong placement of comment.
Fixed wrong description (was 01 ms, should have been 10).
Added Signed-off-by.
drivers/block/mvsata_ide.c | 22 ++++++++++++++--------
1 files changed, 14 insertions(+), 8 deletions(-)
diff --git a/drivers/block/mvsata_ide.c b/drivers/block/mvsata_ide.c
index 077b278..470659d 100644
--- a/drivers/block/mvsata_ide.c
+++ b/drivers/block/mvsata_ide.c
@@ -97,23 +97,27 @@ struct mvsata_port_registers {
* DET back to "no action".
*/
-static void mvsata_ide_initialize_port(struct mvsata_port_registers *port)
+static int mvsata_ide_initialize_port(struct mvsata_port_registers *port)
{
u32 control;
u32 status;
- u32 tout = 50; /* wait at most 50 us for SATA reset to complete */
+ u32 tout = 10000; /* wait at most 10 ms for SATA reset to complete */
+ /* Set control IPM to 3 (no low power) and DET to 1 (initialize) */
control = readl(&port->scontrol);
control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_INIT;
writel(control, &port->scontrol);
+ /* Toggle control DET back to 0 (normal operation) */
+ control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_USE;
+ writel(control, &port->scontrol);
+ /* wait for status DET to become 3 (device and communication OK) */
while (--tout) {
status = readl(&port->sstatus) & MVSATA_SSTATUS_DET_MASK;
if (status == MVSATA_SSTATUS_DET_DEVCOMM)
break;
udelay(1);
}
- control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_USE;
- writel(control, &port->scontrol);
+ return (tout? 0: 1);
}
/*
@@ -125,15 +129,17 @@ int ide_preinit(void)
{
/* Enable ATA port 0 (could be SATA port 0 or 1) if declared */
#if defined(CONFIG_SYS_ATA_IDE0_OFFSET)
- mvsata_ide_initialize_port(
+ if (mvsata_ide_initialize_port(
(struct mvsata_port_registers *)
- (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET));
+ (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET)))
+ return 1;
#endif
/* Enable ATA port 1 (could be SATA port 0 or 1) if declared */
#if defined(CONFIG_SYS_ATA_IDE1_OFFSET)
- mvsata_ide_initialize_port(
+ if (mvsata_ide_initialize_port(
(struct mvsata_port_registers *)
- (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE1_OFFSET));
+ (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE1_OFFSET)))
+ return 1;
#endif
/* return 0 as we always succeed */
return 0;
--
1.7.0.4
More information about the U-Boot
mailing list