[U-Boot] [PATCH V2] mvsata_ide: adjust port init sequence

Prafulla Wadaskar prafulla at marvell.com
Tue Sep 7 08:42:46 CEST 2010


 

> -----Original Message-----
> From: u-boot-bounces at lists.denx.de 
> [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
> Sent: Tuesday, September 07, 2010 4:33 AM
> To: u-boot at lists.denx.de
> Subject: [U-Boot] [PATCH V2] mvsata_ide: adjust port init sequence
> 
> mvsata_ide_initialize_port(): adjust init sequence (SStatus
> should be checked only after all writes to SControl) and
> return success/failure to ide_preinit().
> 
> Also, as some tests showed init durations in the hundreds
> of us, raise the time-out to 10 ms to be on the safe side.
> 
> Signed-off-by: Albert Aribaud <albert.aribaud at free.fr>
> ---
> PATCH HISTORY
> 
> V1	Initial patch.
> V2	Fixed wrong placement of comment.
> 	Fixed wrong description (was 01 ms, should have been 10).
> 	Added Signed-off-by.
> 
>  drivers/block/mvsata_ide.c |   22 ++++++++++++++--------
>  1 files changed, 14 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/block/mvsata_ide.c b/drivers/block/mvsata_ide.c
> index 077b278..470659d 100644
> --- a/drivers/block/mvsata_ide.c
> +++ b/drivers/block/mvsata_ide.c
> @@ -97,23 +97,27 @@ struct mvsata_port_registers {
>   * DET back to "no action".
>   */
>  
> -static void mvsata_ide_initialize_port(struct 
> mvsata_port_registers *port)
> +static int mvsata_ide_initialize_port(struct 
> mvsata_port_registers *port)
>  {
>  	u32 control;
>  	u32 status;
> -	u32 tout = 50; /* wait at most 50 us for SATA reset to 
> complete */
> +	u32 tout = 10000; /* wait at most 10 ms for SATA reset 
> to complete */
>  
> +	/* Set control IPM to 3 (no low power) and DET to 1 
> (initialize) */
>  	control = readl(&port->scontrol);
>  	control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_INIT;
>  	writel(control, &port->scontrol);
> +	/* Toggle control DET back to 0 (normal operation) */
> +	control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_USE;
> +	writel(control, &port->scontrol);
> +	/* wait for status DET to become 3 (device and 
> communication OK) */
>  	while (--tout) {
>  		status = readl(&port->sstatus) & 
> MVSATA_SSTATUS_DET_MASK;
>  		if (status == MVSATA_SSTATUS_DET_DEVCOMM)
>  			break;
>  		udelay(1);
>  	}
> -	control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_USE;
> -	writel(control, &port->scontrol);
> +	return (tout? 0: 1);

As suggested in earlier review, can you pls use !tout instead.
Or please add a space for ":0"

>  }
>  
>  /*
> @@ -125,15 +129,17 @@ int ide_preinit(void)
>  {
>  	/* Enable ATA port 0 (could be SATA port 0 or 1) if declared */
>  #if defined(CONFIG_SYS_ATA_IDE0_OFFSET)
> -	mvsata_ide_initialize_port(
> +	if (mvsata_ide_initialize_port(
>  		(struct mvsata_port_registers *)
> -		(CONFIG_SYS_ATA_BASE_ADDR + 
> CONFIG_SYS_ATA_IDE0_OFFSET));
> +		(CONFIG_SYS_ATA_BASE_ADDR + 
> CONFIG_SYS_ATA_IDE0_OFFSET)))
> +		return 1;

How about returning negative values for errors ?

>  #endif
>  	/* Enable ATA port 1 (could be SATA port 0 or 1) if declared */
>  #if defined(CONFIG_SYS_ATA_IDE1_OFFSET)
> -	mvsata_ide_initialize_port(
> +	if (mvsata_ide_initialize_port(
>  		(struct mvsata_port_registers *)
> -		(CONFIG_SYS_ATA_BASE_ADDR + 
> CONFIG_SYS_ATA_IDE1_OFFSET));
> +		(CONFIG_SYS_ATA_BASE_ADDR + 
> CONFIG_SYS_ATA_IDE1_OFFSET)))
> +		return 1;

Same here

Regards..
Prafulla . .

>  #endif
>  	/* return 0 as we always succeed */
>  	return 0;
> -- 
> 1.7.0.4
> 
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
> 


More information about the U-Boot mailing list