[U-Boot] [PATCH V8 3/6] mv_i2c: use structure to replace the direclty define

Lei Wen leiwen at marvell.com
Tue Apr 5 10:00:57 CEST 2011


Add i2c_clk_enable in the cpu specific code, since previous platform it,
while new platform don't need. In the pantheon and armada100 platform,
this function is defined as NULL one.

Signed-off-by: Lei Wen <leiwen at marvell.com>
---
Changelog:
V2:
NO CHANGE

V3:
clean code sytle issue

V4:
V5:
V6:
NO CHANGE

V7:
Fix comments style
Make global change from PXA to MV

V8:
seperate timeout value fix out

 arch/arm/cpu/pxa/cpu.c                   |   10 ++
 arch/arm/include/asm/arch-pxa/pxa-regs.h |   56 ------------
 board/innokom/innokom.c                  |    9 +--
 drivers/i2c/mv_i2c.c                     |  141 ++++++++++++++---------------
 drivers/i2c/mv_i2c.h                     |   83 +++++++++++++++++
 include/configs/innokom.h                |    1 +
 include/configs/xm250.h                  |    1 +
 7 files changed, 164 insertions(+), 137 deletions(-)
 create mode 100644 drivers/i2c/mv_i2c.h

diff --git a/arch/arm/cpu/pxa/cpu.c b/arch/arm/cpu/pxa/cpu.c
index 7d49cbb..9970a4b 100644
--- a/arch/arm/cpu/pxa/cpu.c
+++ b/arch/arm/cpu/pxa/cpu.c
@@ -318,3 +318,13 @@ int arch_cpu_init(void)
 	pxa_clock_setup();
 	return 0;
 }
+
+void i2c_clk_enable(void)
+{
+	/* set the global I2C clock on */
+#ifdef CONFIG_CPU_MONAHANS
+	writel(readl(CKENB) | (CKENB_4_I2C), CKENB);
+#else
+	writel(readl(CKEN) | CKEN14_I2C, CKEN);
+#endif
+}
diff --git a/arch/arm/include/asm/arch-pxa/pxa-regs.h b/arch/arm/include/asm/arch-pxa/pxa-regs.h
index 65a387f..109fdc0 100644
--- a/arch/arm/include/asm/arch-pxa/pxa-regs.h
+++ b/arch/arm/include/asm/arch-pxa/pxa-regs.h
@@ -456,62 +456,6 @@ typedef void		(*ExcpHndlr) (void) ;
 		IrSR_XMITIR_IR_MODE)
 
 /*
- * I2C registers
- */
-#define IBMR		0x40301680  /* I2C Bus Monitor Register - IBMR */
-#define IDBR		0x40301688  /* I2C Data Buffer Register - IDBR */
-#define ICR		0x40301690  /* I2C Control Register - ICR */
-#define ISR		0x40301698  /* I2C Status Register - ISR */
-#define ISAR		0x403016A0  /* I2C Slave Address Register - ISAR */
-
-#ifdef CONFIG_CPU_MONAHANS
-#define PWRIBMR		0x40f500C0  /* Power I2C Bus Monitor Register-IBMR */
-#define PWRIDBR		0x40f500C4  /* Power I2C Data Buffer Register-IDBR */
-#define PWRICR		0x40f500C8  /* Power I2C Control Register - ICR */
-#define PWRISR		0x40f500CC  /* Power I2C Status Register - ISR */
-#define PWRISAR		0x40f500D0  /* Power I2C Slave Address Register-ISAR */
-#else
-#define PWRIBMR		0x40f00180  /* Power I2C Bus Monitor Register-IBMR */
-#define PWRIDBR		0x40f00188  /* Power I2C Data Buffer Register-IDBR */
-#define PWRICR		0x40f00190  /* Power I2C Control Register - ICR */
-#define PWRISR		0x40f00198  /* Power I2C Status Register - ISR */
-#define PWRISAR		0x40f001A0  /* Power I2C Slave Address Register-ISAR */
-#endif
-
-/* ----- Control register bits ---------------------------------------- */
-
-#define ICR_START	0x1		/* start bit */
-#define ICR_STOP	0x2		/* stop bit */
-#define ICR_ACKNAK	0x4		/* send ACK(0) or NAK(1) */
-#define ICR_TB		0x8		/* transfer byte bit */
-#define ICR_MA		0x10		/* master abort */
-#define ICR_SCLE	0x20		/* master clock enable, mona SCLEA */
-#define ICR_IUE		0x40		/* unit enable */
-#define ICR_GCD		0x80		/* general call disable */
-#define ICR_ITEIE	0x100		/* enable tx interrupts */
-#define ICR_IRFIE	0x200		/* enable rx interrupts, mona: DRFIE */
-#define ICR_BEIE	0x400		/* enable bus error ints */
-#define ICR_SSDIE	0x800		/* slave STOP detected int enable */
-#define ICR_ALDIE	0x1000		/* enable arbitration interrupt */
-#define ICR_SADIE	0x2000		/* slave address detected int enable */
-#define ICR_UR		0x4000		/* unit reset */
-#define ICR_FM		0x8000		/* Fast Mode */
-
-/* ----- Status register bits ----------------------------------------- */
-
-#define ISR_RWM		0x1		/* read/write mode */
-#define ISR_ACKNAK	0x2		/* ack/nak status */
-#define ISR_UB		0x4		/* unit busy */
-#define ISR_IBB		0x8		/* bus busy */
-#define ISR_SSD		0x10		/* slave stop detected */
-#define ISR_ALD		0x20		/* arbitration loss detected */
-#define ISR_ITE		0x40		/* tx buffer empty */
-#define ISR_IRF		0x80		/* rx buffer full */
-#define ISR_GCAD	0x100		/* general call address detected */
-#define ISR_SAD		0x200		/* slave address detected */
-#define ISR_BED		0x400		/* bus error no ACK/NAK */
-
-/*
  * Serial Audio Controller
  */
 /* FIXME the audio defines collide w/ the SA1111 defines.  I don't like these
diff --git a/board/innokom/innokom.c b/board/innokom/innokom.c
index e658c35..22de7e3 100644
--- a/board/innokom/innokom.c
+++ b/board/innokom/innokom.c
@@ -45,12 +45,7 @@ DECLARE_GLOBAL_DATA_PTR;
  */
 int i2c_init_board(void)
 {
-	int i, icr;
-
-	/* disable I2C controller first, otherwhise it thinks we want to    */
-	/* talk to the slave port...                                        */
-	icr = readl(ICR);
-	writel(readl(ICR) & ~(ICR_SCLE | ICR_IUE), ICR);
+	int i;
 
 	/* set gpio pin low _before_ we change direction to output          */
 	writel(GPIO_bit(70), GPCR(70));
@@ -63,8 +58,6 @@ int i2c_init_board(void)
 		udelay(10);
 	}
 
-	writel(icr, ICR);
-
 	return 0;
 }
 
diff --git a/drivers/i2c/mv_i2c.c b/drivers/i2c/mv_i2c.c
index 562b950..7ea66d4 100644
--- a/drivers/i2c/mv_i2c.c
+++ b/drivers/i2c/mv_i2c.c
@@ -8,6 +8,9 @@
  * (C) Copyright 2003 Pengutronix e.K.
  * Robert Schwebel <r.schwebel at pengutronix.de>
  *
+ * (C) Copyright 2011 Marvell Inc.
+ * Lei Wen <leiwen at marvell.com>
+ *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
@@ -34,24 +37,8 @@
 #include <asm/io.h>
 
 #ifdef CONFIG_HARD_I2C
-
-/*
- *	- CONFIG_SYS_I2C_SPEED
- *	- I2C_PXA_SLAVE_ADDR
- */
-
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
 #include <i2c.h>
-
-#if (CONFIG_SYS_I2C_SPEED == 400000)
-#define I2C_ICR_INIT	(ICR_FM | ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD \
-			| ICR_SCLE)
-#else
-#define I2C_ICR_INIT	(ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD | ICR_SCLE)
-#endif
-
-#define I2C_ISR_INIT		0x7FF
+#include "mv_i2c.h"
 
 #ifdef DEBUG_I2C
 #define PRINTD(x) printf x
@@ -59,20 +46,6 @@
 #define PRINTD(x)
 #endif
 
-/* Shall the current transfer have a start/stop condition? */
-#define I2C_COND_NORMAL		0
-#define I2C_COND_START		1
-#define I2C_COND_STOP		2
-
-/* Shall the current transfer be ack/nacked or being waited for it? */
-#define I2C_ACKNAK_WAITACK	1
-#define I2C_ACKNAK_SENDACK	2
-#define I2C_ACKNAK_SENDNAK	4
-
-/* Specify who shall transfer the data (master or slave) */
-#define I2C_READ		0
-#define I2C_WRITE		1
-
 /* All transfers are described by this data structure */
 struct i2c_msg {
 	u8 condition;
@@ -81,27 +54,37 @@ struct i2c_msg {
 	u8 data;
 };
 
+struct mv_i2c {
+	u32 ibmr;
+	u32 pad0;
+	u32 idbr;
+	u32 pad1;
+	u32 icr;
+	u32 pad2;
+	u32 isr;
+	u32 pad3;
+	u32 isar;
+};
+
+static struct mv_i2c *base = (struct mv_i2c *)CONFIG_MV_I2C_REG;
+
 /*
- * i2c_pxa_reset: - reset the host controller
+ * i2c_reset: - reset the host controller
  *
  */
 static void i2c_reset(void)
 {
-	writel(readl(ICR) & ~ICR_IUE, ICR);	/* disable unit */
-	writel(readl(ICR) | ICR_UR, ICR);	/* reset the unit */
+	writel(readl(&base->icr) & ~ICR_IUE, &base->icr); /* disable unit */
+	writel(readl(&base->icr) | ICR_UR, &base->icr);	  /* reset the unit */
 	udelay(100);
-	writel(readl(ICR) & ~ICR_IUE, ICR);	/* disable unit */
-#ifdef CONFIG_CPU_MONAHANS
-	/* | CKENB_1_PWM1 | CKENB_0_PWM0); */
-	writel(readl(CKENB) | (CKENB_4_I2C), CKENB);
-#else /* CONFIG_CPU_MONAHANS */
-	/* set the global I2C clock on */
-	writel(readl(CKEN) | CKEN14_I2C, CKEN);
-#endif
-	writel(I2C_PXA_SLAVE_ADDR, ISAR);	/* set our slave address */
-	writel(I2C_ICR_INIT, ICR);		/* set control reg values */
-	writel(I2C_ISR_INIT, ISR);		/* set clear interrupt bits */
-	writel(readl(ICR) | ICR_IUE, ICR);	/* enable unit */
+	writel(readl(&base->icr) & ~ICR_IUE, &base->icr); /* disable unit */
+
+	i2c_clk_enable();
+
+	writel(CONFIG_SYS_I2C_SLAVE, &base->isar); /* set our slave address */
+	writel(I2C_ICR_INIT, &base->icr); /* set control reg values */
+	writel(I2C_ISR_INIT, &base->isr); /* set clear interrupt bits */
+	writel(readl(&base->icr) | ICR_IUE, &base->icr); /* enable unit */
 	udelay(100);
 }
 
@@ -114,13 +97,15 @@ static void i2c_reset(void)
 static int i2c_isr_set_cleared(unsigned long set_mask,
 			       unsigned long cleared_mask)
 {
-	int timeout = 1000;
+	int timeout = 1000, isr;
 
-	while (((ISR & set_mask) != set_mask) || ((ISR & cleared_mask) != 0)) {
+	do {
+		isr = readl(&base->isr);
 		udelay(10);
 		if (timeout-- < 0)
 			return 0;
-	}
+	} while (((isr & set_mask) != set_mask)
+		|| ((isr & cleared_mask) != 0));
 
 	return 1;
 }
@@ -153,26 +138,26 @@ int i2c_transfer(struct i2c_msg *msg)
 			goto transfer_error_bus_busy;
 
 		/* start transmission */
-		writel(readl(ICR) & ~ICR_START, ICR);
-		writel(readl(ICR) & ~ICR_STOP, ICR);
-		writel(msg->data, IDBR);
+		writel(readl(&base->icr) & ~ICR_START, &base->icr);
+		writel(readl(&base->icr) & ~ICR_STOP, &base->icr);
+		writel(msg->data, &base->idbr);
 		if (msg->condition == I2C_COND_START)
-			writel(readl(ICR) | ICR_START, ICR);
+			writel(readl(&base->icr) | ICR_START, &base->icr);
 		if (msg->condition == I2C_COND_STOP)
-			writel(readl(ICR) | ICR_STOP, ICR);
+			writel(readl(&base->icr) | ICR_STOP, &base->icr);
 		if (msg->acknack == I2C_ACKNAK_SENDNAK)
-			writel(readl(ICR) | ICR_ACKNAK, ICR);
+			writel(readl(&base->icr) | ICR_ACKNAK, &base->icr);
 		if (msg->acknack == I2C_ACKNAK_SENDACK)
-			writel(readl(ICR) & ~ICR_ACKNAK, ICR);
-		writel(readl(ICR) & ~ICR_ALDIE, ICR);
-		writel(readl(ICR) | ICR_TB, ICR);
+			writel(readl(&base->icr) & ~ICR_ACKNAK, &base->icr);
+		writel(readl(&base->icr) & ~ICR_ALDIE, &base->icr);
+		writel(readl(&base->icr) | ICR_TB, &base->icr);
 
 		/* transmit register empty? */
 		if (!i2c_isr_set_cleared(ISR_ITE, 0))
 			goto transfer_error_transmit_timeout;
 
 		/* clear 'transmit empty' state */
-		writel(readl(ISR) | ISR_ITE, ISR);
+		writel(readl(&base->isr) | ISR_ITE, &base->isr);
 
 		/* wait for ACK from slave */
 		if (msg->acknack == I2C_ACKNAK_WAITACK)
@@ -187,28 +172,27 @@ int i2c_transfer(struct i2c_msg *msg)
 			goto transfer_error_bus_busy;
 
 		/* start receive */
-		writel(readl(ICR) & ~ICR_START, ICR);
-		writel(readl(ICR) & ~ICR_STOP, ICR);
+		writel(readl(&base->icr) & ~ICR_START, &base->icr);
+		writel(readl(&base->icr) & ~ICR_STOP, &base->icr);
 		if (msg->condition == I2C_COND_START)
-			writel(readl(ICR) | ICR_START, ICR);
+			writel(readl(&base->icr) | ICR_START, &base->icr);
 		if (msg->condition == I2C_COND_STOP)
-			writel(readl(ICR) | ICR_STOP, ICR);
+			writel(readl(&base->icr) | ICR_STOP, &base->icr);
 		if (msg->acknack == I2C_ACKNAK_SENDNAK)
-			writel(readl(ICR) | ICR_ACKNAK, ICR);
+			writel(readl(&base->icr) | ICR_ACKNAK, &base->icr);
 		if (msg->acknack == I2C_ACKNAK_SENDACK)
-			writel(readl(ICR) & ~ICR_ACKNAK, ICR);
-		writel(readl(ICR) & ~ICR_ALDIE, ICR);
-		writel(readl(ICR) | ICR_TB, ICR);
+			writel(readl(&base->icr) & ~ICR_ACKNAK, &base->icr);
+		writel(readl(&base->icr) & ~ICR_ALDIE, &base->icr);
+		writel(readl(&base->icr) | ICR_TB, &base->icr);
 
 		/* receive register full? */
 		if (!i2c_isr_set_cleared(ISR_IRF, 0))
 			goto transfer_error_receive_timeout;
 
-		msg->data = readl(IDBR);
+		msg->data = readl(&base->idbr);
 
 		/* clear 'receive empty' state */
-		writel(readl(ISR) | ISR_IRF, ISR);
-
+		writel(readl(&base->isr) | ISR_IRF, &base->isr);
 		break;
 	default:
 		goto transfer_error_illegal_param;
@@ -252,10 +236,21 @@ i2c_transfer_finish:
 void i2c_init(int speed, int slaveaddr)
 {
 #ifdef CONFIG_SYS_I2C_INIT_BOARD
-	/* call board specific i2c bus reset routine before accessing the   */
-	/* environment, which might be in a chip on that bus. For details   */
-	/* about this problem see doc/I2C_Edge_Conditions.                  */
+	u32 icr;
+	/*
+	 * call board specific i2c bus reset routine before accessing the
+	 * environment, which might be in a chip on that bus. For details
+	 * about this problem see doc/I2C_Edge_Conditions.
+	 *
+	 * disable I2C controller first, otherwhise it thinks we want to
+	 * talk to the slave port...
+	 */
+	icr = readl(&base->icr);
+	writel(readl(&base->icr) & ~(ICR_SCLE | ICR_IUE), &base->icr);
+
 	i2c_init_board();
+
+	writel(icr, &base->icr);
 #endif
 }
 
diff --git a/drivers/i2c/mv_i2c.h b/drivers/i2c/mv_i2c.h
new file mode 100644
index 0000000..41af0d9
--- /dev/null
+++ b/drivers/i2c/mv_i2c.h
@@ -0,0 +1,83 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Inc, <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _MV_I2C_H_
+#define _MV_I2C_H_
+extern void i2c_clk_enable(void);
+
+/* Shall the current transfer have a start/stop condition? */
+#define I2C_COND_NORMAL		0
+#define I2C_COND_START		1
+#define I2C_COND_STOP		2
+
+/* Shall the current transfer be ack/nacked or being waited for it? */
+#define I2C_ACKNAK_WAITACK	1
+#define I2C_ACKNAK_SENDACK	2
+#define I2C_ACKNAK_SENDNAK	4
+
+/* Specify who shall transfer the data (master or slave) */
+#define I2C_READ		0
+#define I2C_WRITE		1
+
+#if (CONFIG_SYS_I2C_SPEED == 400000)
+#define I2C_ICR_INIT	(ICR_FM | ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD \
+		| ICR_SCLE)
+#else
+#define I2C_ICR_INIT	(ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD | ICR_SCLE)
+#endif
+
+#define I2C_ISR_INIT		0x7FF
+/* ----- Control register bits ---------------------------------------- */
+
+#define ICR_START	0x1		/* start bit */
+#define ICR_STOP	0x2		/* stop bit */
+#define ICR_ACKNAK	0x4		/* send ACK(0) or NAK(1) */
+#define ICR_TB		0x8		/* transfer byte bit */
+#define ICR_MA		0x10		/* master abort */
+#define ICR_SCLE	0x20		/* master clock enable, mona SCLEA */
+#define ICR_IUE		0x40		/* unit enable */
+#define ICR_GCD		0x80		/* general call disable */
+#define ICR_ITEIE	0x100		/* enable tx interrupts */
+#define ICR_IRFIE	0x200		/* enable rx interrupts, mona: DRFIE */
+#define ICR_BEIE	0x400		/* enable bus error ints */
+#define ICR_SSDIE	0x800		/* slave STOP detected int enable */
+#define ICR_ALDIE	0x1000		/* enable arbitration interrupt */
+#define ICR_SADIE	0x2000		/* slave address detected int enable */
+#define ICR_UR		0x4000		/* unit reset */
+#define ICR_FM		0x8000		/* Fast Mode */
+
+/* ----- Status register bits ----------------------------------------- */
+
+#define ISR_RWM		0x1		/* read/write mode */
+#define ISR_ACKNAK	0x2		/* ack/nak status */
+#define ISR_UB		0x4		/* unit busy */
+#define ISR_IBB		0x8		/* bus busy */
+#define ISR_SSD		0x10		/* slave stop detected */
+#define ISR_ALD		0x20		/* arbitration loss detected */
+#define ISR_ITE		0x40		/* tx buffer empty */
+#define ISR_IRF		0x80		/* rx buffer full */
+#define ISR_GCAD	0x100		/* general call address detected */
+#define ISR_SAD		0x200		/* slave address detected */
+#define ISR_BED		0x400		/* bus error no ACK/NAK */
+
+#endif
diff --git a/include/configs/innokom.h b/include/configs/innokom.h
index 0ea73c9..744d65c 100644
--- a/include/configs/innokom.h
+++ b/include/configs/innokom.h
@@ -141,6 +141,7 @@
  * I2C bus
  */
 #define CONFIG_I2C_MV			1
+#define CONFIG_MV_I2C_REG		0x40301680
 #define CONFIG_HARD_I2C			1
 #define CONFIG_SYS_I2C_SPEED			50000
 #define CONFIG_SYS_I2C_SLAVE			0xfe
diff --git a/include/configs/xm250.h b/include/configs/xm250.h
index b4b940a..232baf3 100644
--- a/include/configs/xm250.h
+++ b/include/configs/xm250.h
@@ -62,6 +62,7 @@
  * I2C bus
  */
 #define CONFIG_I2C_MV			1
+#define CONFIG_MV_I2C_REG		0x40301680
 #define CONFIG_HARD_I2C			1
 #define CONFIG_SYS_I2C_SPEED			50000
 #define CONFIG_SYS_I2C_SLAVE			0xfe
-- 
1.7.0.4



More information about the U-Boot mailing list