[U-Boot] [PATCH 02/30] powerpc/km82xx: add DIP switch detection

Valentin Longchamp valentin.longchamp at keymile.com
Fri Apr 8 16:23:52 CEST 2011


From: Huber, Andreas <Andreas.Huber at keymile.com>

This reads the DIP switch register in the BFTICU (0x40000089). If 'Full reset'
or 'DB erase' is selected, 'actual_bank' is set to 0. This loads the Bootloader
application who does the erase stuff. To access the register a struct for the
bfticu I/O map was added to common.h.

Signed-off-by: Andreas Huber <andreas.huber at keymile.com>
Signed-off-by: Holger Brunck <holger.brunck at keymile.com>
Acked-by: Heiko Schocher <hs at denx.de>
cc: Wolfgang Denk <wd at denx.de>
cc: Detlev Zundel <dzu at denx.de>
cc: Valentin Longchamp <valentin.longchamp at keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
---
 board/keymile/common/common.h |   79 +++++++++++++++++++++++++++++++++++++++++
 board/keymile/mgcoge/mgcoge.c |   12 ++++++
 2 files changed, 91 insertions(+), 0 deletions(-)

diff --git a/board/keymile/common/common.h b/board/keymile/common/common.h
index 099de98..cdc35b6 100644
--- a/board/keymile/common/common.h
+++ b/board/keymile/common/common.h
@@ -39,6 +39,85 @@ struct km_bec_fpga {
 	unsigned char	pgy_eth;
 };
 
+#define BFTICU_DIPSWITCH_MASK   0x0f
+
+/*
+ * BFTICU FPGA iomap
+ * BFTICU is used on mgcoge and mgocge3ne
+ */
+struct bfticu_iomap {
+	u8	xi_ena;		/* General defect enable */
+	u8	pack1[3];
+	u8	en_csn;
+	u8	pack2;
+	u8	safe_mem;
+	u8	pack3;
+	u8	id;
+	u8	pack4;
+	u8	rev;
+	u8	build;
+	u8	p_frc;
+	u8	p_msk;
+	u8	pack5[2];
+	u8	xg_int;
+	u8	pack6[15];
+	u8	s_conf;
+	u8	pack7;
+	u8	dmx_conf12;
+	u8	pack8;
+	u8	s_clkslv;
+	u8	pack9[11];
+	u8	d_conf;
+	u8	d_mask_ca;
+	u8	d_pll_del;
+	u8	pack10[16];
+	u8	t_conf_ca;
+	u8	t_mask_ca;
+	u8	pack11[13];
+	u8	m_def0;
+	u8	m_def1;
+	u8	m_def2;
+	u8	m_def3;
+	u8	m_def4;
+	u8	m_def5;
+	u8	m_def_trap0;
+	u8	m_def_trap1;
+	u8	m_def_trap2;
+	u8	m_def_trap3;
+	u8	m_def_trap4;
+	u8	m_def_trap5;
+	u8	m_mask_def0;
+	u8	m_mask_def1;
+	u8	m_mask_def2;
+	u8	m_mask_def3;
+	u8	m_mask_def4;
+	u8	m_mask_def5;
+	u8	m_def_mask0;
+	u8	m_def_mask1;
+	u8	m_def_mask2;
+	u8	m_def_mask3;
+	u8	m_def_mask4;
+	u8	m_def_mask5;
+	u8	m_def_pri;
+	u8	pack12[11];
+	u8	hw_status;
+	u8	pack13;
+	u8	hw_control1;
+	u8	hw_control2;
+	u8	hw_control3;
+	u8	pack14[7];
+	u8	led_on;		/* Leds */
+	u8	pack15;
+	u8	sfp_control;	/* SFP modules */
+	u8	pack16;
+	u8	alarm_control;	/* Alarm output */
+	u8	pack17;
+	u8	icps;		/* ICN clock pulse shaping */
+	u8	mswitch;	/* Read mode switch */
+	u8	pack18[6];
+	u8	pb_dbug;
+};
+
 #if !defined(CONFIG_PIGGY_MAC_ADRESS_OFFSET)
 #define CONFIG_PIGGY_MAC_ADRESS_OFFSET	0
 #endif
diff --git a/board/keymile/mgcoge/mgcoge.c b/board/keymile/mgcoge/mgcoge.c
index 340016b..11a0f79 100644
--- a/board/keymile/mgcoge/mgcoge.c
+++ b/board/keymile/mgcoge/mgcoge.c
@@ -315,6 +315,18 @@ int board_early_init_r(void)
 
 int last_stage_init(void)
 {
+	struct bfticu_iomap *base =
+		(struct bfticu_iomap *)CONFIG_SYS_FPGA_BASE;
+	u8 dip_switch;
+
+	dip_switch = in_8(&base->mswitch);
+	dip_switch &= BFTICU_DIPSWITCH_MASK;
+	/* dip switch 'full reset' or 'db erase' */
+	if (dip_switch & 0x1 || dip_switch & 0x2) {
+		/* start bootloader */
+		puts("DIP:   Enabled\n");
+		setenv("actual_bank", "0");
+	}
 	set_km_env();
 	return 0;
 }
-- 
1.7.0.5



More information about the U-Boot mailing list