[U-Boot] [PATCH v2 3/4] Initialize second PHY on OpenRD-Client and OpenRD-Ultimate

[Clint Adams]

(rework of Julian Pidancet's patch)
---
 board/Marvell/openrd/openrd.c |   25 +++++++++++++++++++++----
 include/configs/openrd.h      |   14 ++++++++++++--
 2 files changed, 33 insertions(+), 6 deletions(-)

diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c
index 14ca88e..b2f7adb 100644
--- a/board/Marvell/openrd/openrd.c
+++ b/board/Marvell/openrd/openrd.c
@@ -124,12 +124,11 @@ int board_init(void)
 }
 
 #ifdef CONFIG_RESET_PHY_R
-/* Configure and enable MV88E1116 PHY */
-void reset_phy(void)
+/* Configure and enable MV88E1116/88E1121 PHY */
+void mv_phy_init(char *name)
 {
 	u16 reg;
 	u16 devadr;
-	char *name = "egiga0";
 
 	if (miiphy_set_current_dev(name))
 		return;
@@ -154,6 +153,24 @@ void reset_phy(void)
 	/* reset the phy */
 	miiphy_reset(name, devadr);
 
-	printf("88E1116 Initialized on %s\n", name);
+	printf(PHY_NO" Initialized on %s\n", name);
+}
+
+void reset_phy(void)
+{
+       mv_phy_init("egiga0");
+
+#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT
+       /* Kirkwood ethernet driver is written with the assumption that in case
+        * of multiple PHYs, their addresses are consecutive. But unfortunately
+        * in case of OpenRD-Client, PHY addresses are not consecutive.*/
+       miiphy_write("egiga1", 0xEE, 0xEE, 24);
+#endif
+
+#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \
+    defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
+       /* configure and initialize both PHY's */
+       mv_phy_init("egiga1");
+#endif
 }
 #endif /* CONFIG_RESET_PHY_R */
diff --git a/include/configs/openrd.h b/include/configs/openrd.h
index 7299749..8d86067 100644
--- a/include/configs/openrd.h
+++ b/include/configs/openrd.h
@@ -117,8 +117,18 @@
  * Ethernet Driver configuration
  */
 #ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR	0x8
+# ifdef CONFIG_BOARD_IS_OPENRD_BASE
+#  define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
+# else
+#  define CONFIG_MVGBE_PORTS	{1, 1}	/* enable both ports */
+# endif
+# ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE
+#  define CONFIG_PHY_BASE_ADR	0x0
+#  define PHY_NO		"88E1121"
+# else
+#  define CONFIG_PHY_BASE_ADR	0x8
+#  define PHY_NO		"88E1116"
+# endif
 #endif /* CONFIG_CMD_NET */
 
 /*
-- 
1.7.4.1