[U-Boot] Please pull u-boot-ti/master

[Albert ARIBAUD]

Hi Tom,

Le 29/11/2011 23:53, Tom Rini a écrit :
> The following changes since commit f2695a272849764cda09bcce6f86d03105e9e46d:
>    Marek Vasut (1):
>          PXA: Drop XM250 board
>
> are available in the git repository at:
>
>    git://git.denx.de/u-boot-ti.git master
>
> Anatolij Gustschin (1):
>        ARM: davinci_dm6467Tevm: Fix build breakage
>
> Aneesh V (13):
>        armv7: disable L2 cache in cleanup_before_linux()
>        armv7: include armv7/cpu.c in SPL build
>        armv7: setup vector
>        start.S: remove omap3 specific code from start.S
>        omap: Improve PLL parameter calculation tool
>        omap4: ttyO2 instead of ttyS2 in default bootargs
>        omap: fix cache line size for omap3/omap4 boards
>        omap4460: fix TPS initialization
>        omap: remove I2C from SPL
>        omap4: emif: fix error in driver
>        omap4460: add ES1.1 identification
>        omap4+: streamline CONFIG_SYS_TEXT_BASE and other SDRAM addresses
>        omap4: fix IO setting
>
> Christian Riesch (8):
>        arm, davinci: Move pinmux functions from board to arch tree
>        arm, hawkboard: Remove obsolete struct pinmux_config i2c_pins
>        arm, da850evm: Do pinmux configuration for EMAC together with
> other pinmuxes
>        arm, da850: Add pinmux configurations to the arch tree
>        arm, da850evm: Use the pinmux configurations defined in the arch tree
>        arm, hawkboard: Use the pinmux configurations defined in the arch tree
>        arm, davinci: Remove duplication of pinmux configuration code
>        arm: printf() is not available in some SPL configurations
>
> Heiko Schocher (6):
>        arm, arm926ejs: always do cpu critical inits
>        arm, davinci: move davinci_rtc struct to hardware.h
>        arm, davinci, da850: add uart1 tx rx pinmux config
>        arm, board/davinci/common/misc.c: Codingstyle cleanup
>        arm, davinci: move misc function in arch tree
>        arm, davinci: add support for am1808 based enbw_cmc board
>
> Ilya Yanok (10):
>        davinci_emac: move arch-independent defines to separate header
>        davinci_emac: use internal addresses in buffer descriptors
>        davinci_emac: conditionally compile specific PHY support
>        arm926ejs: add noop implementation for dcache ops
>        davinci_emac: fix for running with dcache enabled
>        davinci_emac: hardcode 100Mbps for AM35xx and RMII
>        AM35xx: add EMAC support
>        AM3517: move AM3517 specific mux defines to generic header
>        nand_spl_simple: add support for software ECC
>        omap_gpmc: use SOFTECC in SPL if it's enabled
>
> Koen Kooi (1):
>        BeagleBoard: config: Really switch to ttyO2
>
> Prabhakar Lad (1):
>        ARM: davici_emac: Fix condition for number of phy detects
>
> Thomas Weber (3):
>        ARM: OMAP3: Remove unused define CONFIG_OMAP3430
>        ARM: OMAP3: Remove unused define SDRC_R_C_B
>        ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused
>
> Tom Rini (15):
>        omap3: mem: Comment enable_gpmc_cs_config more
>        OMAP3: Update SDRC dram_init to always call make_cs1_contiguous()
>        OMAP3: Add a helper function to set timings in SDRC
>        OMAP3: Change mem_ok to clear again after reading back
>        OMAP3: Remove get_mem_type prototype
>        omap3: mem: Add MCFG helper macro
>        OMAP3: Add optimal SDRC autorefresh control values
>        OMAP3: Suffix all Micron memory timing parts with their speed
>        OMAP3 SPL: Rework memory initalization and devkit8000 support
>        OMAP3 SPL: Add identify_nand_chip function
>        OMAP3: Add SPL support to Beagleboard
>        OMAP3: Add SPL support to omap3_evm
>        AM3517: Add SPL support
>        AM3517 CraneBoard: Add SPL support
>        OMAP3: Add SPL_BOARD_INIT hook

Applied to u-boot-arm/master, thanks.

Amicalement,
-- 
Albert.