[U-Boot] [PATCH v2 6/6] reboard: arm: Remove unused code in start.S
Simon Glass
sjg at chromium.org
Sat Dec 10 20:16:16 CET 2011
Now that we are using the generic relocation framework, we don't need this
code.
Note: Here we lose the ARM1176's enable_mmu code. This seems to duplicate
code already in U-Boot now. Can anyone comment on this?
Signed-off-by: Simon Glass <sjg at chromium.org>
---
Changes in v2:
- Make relocation symbols global so we can use them outside start.S
arch/arm/cpu/arm1136/start.S | 133 +++----------------------
arch/arm/cpu/arm1176/start.S | 214 +++-------------------------------------
arch/arm/cpu/arm720t/start.S | 127 +++---------------------
arch/arm/cpu/arm920t/start.S | 135 +++-----------------------
arch/arm/cpu/arm925t/start.S | 135 +++-----------------------
arch/arm/cpu/arm926ejs/start.S | 144 +++------------------------
arch/arm/cpu/arm946es/start.S | 130 +++----------------------
arch/arm/cpu/arm_intcm/start.S | 135 +++-----------------------
arch/arm/cpu/armv7/start.S | 141 +++-----------------------
arch/arm/cpu/ixp/start.S | 127 +++---------------------
arch/arm/cpu/lh7a40x/start.S | 124 +++---------------------
arch/arm/cpu/pxa/start.S | 138 +++-----------------------
arch/arm/cpu/s3c44b0/start.S | 127 +++---------------------
arch/arm/cpu/sa1100/start.S | 124 +++---------------------
14 files changed, 171 insertions(+), 1763 deletions(-)
diff --git a/arch/arm/cpu/arm1136/start.S b/arch/arm/cpu/arm1136/start.S
index c0db96c..f1efa5e 100644
--- a/arch/arm/cpu/arm1136/start.S
+++ b/arch/arm/cpu/arm1136/start.S
@@ -108,6 +108,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -169,127 +181,6 @@ call_board_init_f:
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-#endif /* #ifndef CONFIG_SPL_BUILD */
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr r0, _nand_boot_ofs
- mov pc, r0
-
-_nand_boot_ofs:
- .word nand_boot
-#else
-jump_2_ram:
- ldr r0, _board_init_r_ofs
- ldr r1, _TEXT_BASE
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/arm1176/start.S b/arch/arm/cpu/arm1176/start.S
index 848144a..a413f51 100644
--- a/arch/arm/cpu/arm1176/start.S
+++ b/arch/arm/cpu/arm1176/start.S
@@ -127,6 +127,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
@@ -231,208 +243,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-#ifdef CONFIG_ENABLE_MMU
-enable_mmu:
- /* enable domain access */
- ldr r5, =0x0000ffff
- mcr p15, 0, r5, c3, c0, 0 /* load domain access register */
-
- /* Set the TTB register */
- ldr r0, _mmu_table_base
- ldr r1, =CONFIG_SYS_PHY_UBOOT_BASE
- ldr r2, =0xfff00000
- bic r0, r0, r2
- orr r1, r0, r1
- mcr p15, 0, r1, c2, c0, 0
-
- /* Enable the MMU */
- mrc p15, 0, r0, c1, c0, 0
- orr r0, r0, #1 /* Set CR_M to enable MMU */
-
- /* Prepare to enable the MMU */
- adr r1, skip_hw_init
- and r1, r1, #0x3fc
- ldr r2, _TEXT_BASE
- ldr r3, =0xfff00000
- and r2, r2, r3
- orr r2, r2, r1
- b mmu_enable
-
- .align 5
- /* Run in a single cache-line */
-mmu_enable:
-
- mcr p15, 0, r0, c1, c0, 0
- nop
- nop
- mov pc, r2
-skip_hw_init:
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-
-#ifndef CONFIG_NAND_SPL
- bl coloured_LED_init
- bl red_led_on
-#endif
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr pc, _nand_boot
-
-_nand_boot: .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
-#ifdef CONFIG_ENABLE_MMU
-_mmu_table_base:
- .word mmu_table
-#endif
-
-#ifndef CONFIG_NAND_SPL
-/*
- * we assume that cache operation is done before. (eg. cleanup_before_linux())
- * actually, we don't need to do anything about cache if not use d-cache in
- * U-Boot. So, in this function we clean only MMU. by scsuh
- *
- * void theLastJump(void *kernel, int arch_num, uint boot_params);
- */
-#ifdef CONFIG_ENABLE_MMU
- .globl theLastJump
-theLastJump:
- mov r9, r0
- ldr r3, =0xfff00000
- ldr r4, _TEXT_PHY_BASE
- adr r5, phy_last_jump
- bic r5, r5, r3
- orr r5, r5, r4
- mov pc, r5
-phy_last_jump:
- /*
- * disable MMU stuff
- */
- mrc p15, 0, r0, c1, c0, 0
- bic r0, r0, #0x00002300 /* clear bits 13, 9:8 (--V- --RS) */
- bic r0, r0, #0x00000087 /* clear bits 7, 2:0 (B--- -CAM) */
- orr r0, r0, #0x00000002 /* set bit 2 (A) Align */
- orr r0, r0, #0x00001000 /* set bit 12 (I) I-Cache */
- mcr p15, 0, r0, c1, c0, 0
-
- mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */
-
- mov r0, #0
- mov pc, r9
-#endif
-
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/arm720t/start.S b/arch/arm/cpu/arm720t/start.S
index 540e3c2..c703a88 100644
--- a/arch/arm/cpu/arm720t/start.S
+++ b/arch/arm/cpu/arm720t/start.S
@@ -97,6 +97,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -146,121 +158,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-
- bl coloured_LED_init
- bl red_led_on
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/arm920t/start.S b/arch/arm/cpu/arm920t/start.S
index 8c5612c..75f9043 100644
--- a/arch/arm/cpu/arm920t/start.S
+++ b/arch/arm/cpu/arm920t/start.S
@@ -93,6 +93,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -189,129 +201,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-
- bl coloured_LED_init
- bl red_led_on
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr r0, _nand_boot_ofs
- mov pc, r0
-
-_nand_boot_ofs:
- .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/arm925t/start.S b/arch/arm/cpu/arm925t/start.S
index dbb93ef..30df379 100644
--- a/arch/arm/cpu/arm925t/start.S
+++ b/arch/arm/cpu/arm925t/start.S
@@ -103,6 +103,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -183,129 +195,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-
- bl coloured_LED_init
- bl red_led_on
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr r0, _nand_boot_ofs
- mov pc, r0
-
-_nand_boot_ofs:
- .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/arm926ejs/start.S b/arch/arm/cpu/arm926ejs/start.S
index 6a09c02..ac358bc 100644
--- a/arch/arm/cpu/arm926ejs/start.S
+++ b/arch/arm/cpu/arm926ejs/start.S
@@ -160,6 +160,18 @@ _end:
.word __bss_end__
#endif
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -211,138 +223,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- sub r9, r6, r0 /* r9 <- relocation offset */
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifdef CONFIG_SPL_BUILD
- /* No relocation for SPL */
- ldr r0, =__bss_start
- ldr r1, =__bss_end__
-#else
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
-#endif
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-
-#ifndef CONFIG_SPL_BUILD
- bl coloured_LED_init
- bl red_led_on
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr r0, _nand_boot_ofs
- mov pc, r0
-
-_nand_boot_ofs:
- .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- ldr r1, _TEXT_BASE
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/arm946es/start.S b/arch/arm/cpu/arm946es/start.S
index 89ba558..7c5d19f 100644
--- a/arch/arm/cpu/arm946es/start.S
+++ b/arch/arm/cpu/arm946es/start.S
@@ -109,6 +109,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -154,124 +166,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- blo clbss_l
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr pc, _nand_boot
-
-_nand_boot: .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/arm_intcm/start.S b/arch/arm/cpu/arm_intcm/start.S
index 2033b36..28fa6c6 100644
--- a/arch/arm/cpu/arm_intcm/start.S
+++ b/arch/arm/cpu/arm_intcm/start.S
@@ -105,6 +105,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -150,129 +162,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-
- bl coloured_LED_init
- bl red_led_on
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr r0, _nand_boot_ofs
- mov pc, r0
-
-_nand_boot_ofs:
- .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/armv7/start.S b/arch/arm/cpu/armv7/start.S
index 4d8cf35..86510c7 100644
--- a/arch/arm/cpu/armv7/start.S
+++ b/arch/arm/cpu/armv7/start.S
@@ -96,6 +96,7 @@ _armboot_start:
/*
* These are defined in the board-specific linker script.
+ * TODO: move these into proc.S since they are common
*/
.globl _bss_start_ofs
_bss_start_ofs:
@@ -113,6 +114,20 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+#ifndef CONFIG_SPL_BUILD
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+#endif
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -176,132 +191,6 @@ call_board_init_f:
/*------------------------------------------------------------------------------*/
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _image_copy_end_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
- b clear_bss
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
-#endif /* #ifndef CONFIG_SPL_BUILD */
-
-clear_bss:
-#ifdef CONFIG_SPL_BUILD
- /* No relocation for SPL */
- ldr r0, =__bss_start
- ldr r1, =__bss_end__
-#else
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
-#endif
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-jump_2_ram:
-/*
- * If I-cache is enabled invalidate it
- */
-#ifndef CONFIG_SYS_ICACHE_OFF
- mcr p15, 0, r0, c7, c5, 0 @ invalidate icache
- mcr p15, 0, r0, c7, c10, 4 @ DSB
- mcr p15, 0, r0, c7, c5, 4 @ ISB
-#endif
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-
-
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
/*************************************************************************
*
diff --git a/arch/arm/cpu/ixp/start.S b/arch/arm/cpu/ixp/start.S
index cb32121..6ecf72e 100644
--- a/arch/arm/cpu/ixp/start.S
+++ b/arch/arm/cpu/ixp/start.S
@@ -118,6 +118,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -252,121 +264,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-
- bl coloured_LED_init
- bl red_led_on
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/****************************************************************************/
/* */
/* Interrupt handling */
diff --git a/arch/arm/cpu/lh7a40x/start.S b/arch/arm/cpu/lh7a40x/start.S
index 62de8b8..80bd15b 100644
--- a/arch/arm/cpu/lh7a40x/start.S
+++ b/arch/arm/cpu/lh7a40x/start.S
@@ -93,6 +93,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -163,118 +175,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/pxa/start.S b/arch/arm/cpu/pxa/start.S
index ba0de8f..6255151 100644
--- a/arch/arm/cpu/pxa/start.S
+++ b/arch/arm/cpu/pxa/start.S
@@ -126,6 +126,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -171,132 +183,6 @@ call_board_init_f:
ldr r0, =0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-#ifndef CONFIG_SPL_BUILD
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
-/* Disable the Dcache RAM lock for stack now */
-#ifdef CONFIG_CPU_PXA25X
- bl cpu_init_crit
-#endif
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-#endif /* #ifndef CONFIG_SPL_BUILD */
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_ONENAND_SPL
- ldr r0, _onenand_boot_ofs
- mov pc, r0
-
-_onenand_boot_ofs:
- .word onenand_boot
-#else
-jump_2_ram:
- ldr r0, _board_init_r_ofs
- ldr r1, _TEXT_BASE
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-#endif
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/s3c44b0/start.S b/arch/arm/cpu/s3c44b0/start.S
index a29d5b4..f52e94b 100644
--- a/arch/arm/cpu/s3c44b0/start.S
+++ b/arch/arm/cpu/s3c44b0/start.S
@@ -84,6 +84,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -135,121 +147,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-
- bl coloured_LED_init
- bl red_led_on
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*
*************************************************************************
*
diff --git a/arch/arm/cpu/sa1100/start.S b/arch/arm/cpu/sa1100/start.S
index 92546d8..2221788 100644
--- a/arch/arm/cpu/sa1100/start.S
+++ b/arch/arm/cpu/sa1100/start.S
@@ -94,6 +94,18 @@ _bss_end_ofs:
_end_ofs:
.word _end - _start
+.globl _rel_dyn_start_ofs
+_rel_dyn_start_ofs:
+ .word __rel_dyn_start - _start
+
+.globl _rel_dyn_end_ofs
+_rel_dyn_end_ofs:
+ .word __rel_dyn_end - _start
+
+.globl _dynsym_start_ofs
+_dynsym_start_ofs:
+ .word __dynsym_start - _start
+
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -139,118 +151,6 @@ call_board_init_f:
ldr r0,=0x00000000
bl board_init_f
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
- .globl relocate_code
-relocate_code:
- mov r4, r0 /* save addr_sp */
- mov r5, r1 /* save addr of gd */
- mov r6, r2 /* save addr of destination */
-
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
- adr r0, _start
- cmp r0, r6
- beq clear_bss /* skip relocation */
- mov r1, r6 /* r1 <- scratch for copy_loop */
- ldr r3, _bss_start_ofs
- add r2, r0, r3 /* r2 <- source end address */
-
-copy_loop:
- ldmia r0!, {r9-r10} /* copy from source address [r0] */
- stmia r1!, {r9-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- blo copy_loop
-
-#ifndef CONFIG_SPL_BUILD
- /*
- * fix .rel.dyn relocations
- */
- ldr r0, _TEXT_BASE /* r0 <- Text base */
- sub r9, r6, r0 /* r9 <- relocation offset */
- ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
- add r10, r10, r0 /* r10 <- sym table in FLASH */
- ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
- add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
- ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
- add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
-fixloop:
- ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
- add r0, r0, r9 /* r0 <- location to fix up in RAM */
- ldr r1, [r2, #4]
- and r7, r1, #0xff
- cmp r7, #23 /* relative fixup? */
- beq fixrel
- cmp r7, #2 /* absolute fixup? */
- beq fixabs
- /* ignore unknown type of fixup */
- b fixnext
-fixabs:
- /* absolute fix: set location to (offset) symbol value */
- mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
- add r1, r10, r1 /* r1 <- address of symbol in table */
- ldr r1, [r1, #4] /* r1 <- symbol value */
- add r1, r1, r9 /* r1 <- relocated sym addr */
- b fixnext
-fixrel:
- /* relative fix: increase location by offset */
- ldr r1, [r0]
- add r1, r1, r9
-fixnext:
- str r1, [r0]
- add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
- cmp r2, r3
- blo fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-
-_rel_dyn_start_ofs:
- .word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
- .word __rel_dyn_end - _start
-_dynsym_start_ofs:
- .word __dynsym_start - _start
-
/*
*************************************************************************
*
--
1.7.3.1
More information about the U-Boot
mailing list