[U-Boot] [PATCH] Kirkwood: Add support for OpenRD-Client & OpenRD-Ultimate
Julian Pidancet
julian.pidancet at citrix.com
Tue Feb 8 19:20:54 CET 2011
This patch modifies existing OpenRD-Base support to deal with all
the three OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate).
This is a rebase onto master from an original patch sent by Tanmay Upadhyay a few months ago.
All credits goes to him.
It's been tested on my OpenRD-Ultimate and works perfectly fine.
Signed-off-by: Julian Pidancet <julian.pidancet at citrix.com>
---
MAKEALL | 2 +
board/Marvell/openrd/Makefile | 56 ++++++++++
board/Marvell/openrd/config.mk | 33 ++++++
board/Marvell/openrd/kwbimage.cfg | 168 ++++++++++++++++++++++++++++++
board/Marvell/openrd/openrd.c | 173 +++++++++++++++++++++++++++++++
board/Marvell/openrd/openrd.h | 50 +++++++++
board/Marvell/openrd_base/Makefile | 56 ----------
board/Marvell/openrd_base/kwbimage.cfg | 168 ------------------------------
board/Marvell/openrd_base/openrd_base.c | 153 ---------------------------
board/Marvell/openrd_base/openrd_base.h | 46 --------
boards.cfg | 4 +-
include/configs/openrd.h | 115 ++++++++++++++++++++
include/configs/openrd_base.h | 92 +++--------------
include/configs/openrd_client.h | 50 +++++++++
include/configs/openrd_ultimate.h | 50 +++++++++
15 files changed, 714 insertions(+), 502 deletions(-)
create mode 100644 board/Marvell/openrd/Makefile
create mode 100644 board/Marvell/openrd/config.mk
create mode 100644 board/Marvell/openrd/kwbimage.cfg
create mode 100644 board/Marvell/openrd/openrd.c
create mode 100644 board/Marvell/openrd/openrd.h
delete mode 100644 board/Marvell/openrd_base/Makefile
delete mode 100644 board/Marvell/openrd_base/kwbimage.cfg
delete mode 100644 board/Marvell/openrd_base/openrd_base.c
delete mode 100644 board/Marvell/openrd_base/openrd_base.h
create mode 100644 include/configs/openrd.h
create mode 100644 include/configs/openrd_client.h
create mode 100644 include/configs/openrd_ultimate.h
diff --git a/MAKEALL b/MAKEALL
index a732e6a..4b6da98 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -361,6 +361,8 @@ LIST_ARM9=" \
omap5912osk \
omap730p2 \
openrd_base \
+ openrd_client \
+ openrd_ultimate \
rd6281a \
sbc2410x \
scb9328 \
diff --git a/board/Marvell/openrd/Makefile b/board/Marvell/openrd/Makefile
new file mode 100644
index 0000000..19020e4
--- /dev/null
+++ b/board/Marvell/openrd/Makefile
@@ -0,0 +1,56 @@
+#
+# (C) Copyright 2009
+# Net Insight <www.netinsight.net>
+# Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
+#
+# Based on sheevaplug:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := openrd.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/openrd/config.mk b/board/Marvell/openrd/config.mk
new file mode 100644
index 0000000..8ae355e
--- /dev/null
+++ b/board/Marvell/openrd/config.mk
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2009
+# Net Insight <www.netinsight.net>
+# Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
+#
+# Based on sheevaplug:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
+
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
diff --git a/board/Marvell/openrd/kwbimage.cfg b/board/Marvell/openrd/kwbimage.cfg
new file mode 100644
index 0000000..757eb28
--- /dev/null
+++ b/board/Marvell/openrd/kwbimage.cfg
@@ -0,0 +1,168 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30 # DDR Configuration register
+# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
+# bit 4: 0=addr/cmd in smame cycle
+# bit 5: 0=clk is driven during self refresh, we don't care for APX
+# bit 6: 0=use recommended falling edge of clk for addr/cmd
+# bit14: 0=input buffer always powered up
+# bit18: 1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31: 0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x000000cc # DDR Address Control
+# bit1-0: 00, Cs0width=x8
+# bit3-2: 11, Cs0size=1Gb
+# bit5-4: 00, Cs1width=x8
+# bit7-6: 11, Cs1size=1Gb
+# bit9-8: 00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000C52 # DDR Mode
+# bit2-0: 2, BurstLen=2 required
+# bit3: 0, BurstType=0 required
+# bit6-4: 4, CL=5
+# bit7: 0, TestMode=0 normal
+# bit8: 0, DLL reset=0 normal
+# bit11-9: 6, auto-precharge write recovery ????????????
+# bit12: 0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000042 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 1, DDR drive strength reduced
+# bit2: 0, DDR ODT control lsd (disabled)
+# bit5-3: 000, required
+# bit6: 1, DDR ODT control msb, (disabled)
+# bit9-7: 000, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
+# bit2-0: 111, required
+# bit3 : 1 , MBUS Burst Chop disabled
+# bit6-4: 111, required
+# bit7 : 0
+# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9 : 0 , no half clock cycle addition to dataout
+# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
+
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
+# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
+# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
+# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
+# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+
+DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
+# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
+# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
+# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
+# bit14: 1, M_STARTBURST_IN ODT: Enabled
+# bit15: 1, DDR IO ODT Unit: Use ODT block
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c
new file mode 100644
index 0000000..2d34a24
--- /dev/null
+++ b/board/Marvell/openrd/openrd.c
@@ -0,0 +1,173 @@
+/*
+ * Modified Simon's work to deal with all the three variants of
+ * OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate)
+ *
+ * eInfochips <www.einfochips.com>
+ * Modified-by: Tanmay Upadhyay <tanmay.upadhyay at einfochips.com>
+ *
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
+ *
+ * Based on sheevaplug.c:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "openrd.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(OPENRD_OE_VAL_LOW,
+ OPENRD_OE_VAL_HIGH,
+ OPENRD_OE_LOW, OPENRD_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD, /* Alt UART1_TXD */
+ MPP14_SD_D0, /* Alt UART1_RXD */
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0,
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GPIO, /* UART1 / SD sel */
+ MPP35_TDM_CH0_TX_QL,
+ MPP36_TDM_SPI_CS1,
+ MPP37_TDM_CH2_TX_QL,
+ MPP38_TDM_CH2_RX_QL,
+ MPP39_AUDIO_I2SBCLK,
+ MPP40_AUDIO_I2SDO,
+ MPP41_AUDIO_I2SLRC,
+ MPP42_AUDIO_I2SMCLK,
+ MPP43_AUDIO_I2SDI,
+ MPP44_AUDIO_EXTCLK,
+ MPP45_TDM_PCLK,
+ MPP46_TDM_FS,
+ MPP47_TDM_DRX,
+ MPP48_TDM_DTX,
+ MPP49_TDM_CH0_RX_QL,
+ 0
+ };
+
+ kirkwood_mpp_conf(kwmpp_config);
+ return 0;
+}
+
+int board_init(void)
+{
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_OPENRD;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116/MV88E1121 PHY */
+void mv_phy_init(char *name)
+{
+ u16 reg;
+ u16 devadr;
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n", __func__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, PGADR_REG, 2);
+ miiphy_read(name, devadr, MAC_CTRL_REG, ®);
+ reg |= (RGMII_RXTM_CTRL | RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, PGADR_REG, 0);
+
+ /* reset the phy */
+ if (!miiphy_reset(name, devadr))
+ printf("%s Initialized on %s\n", PHY_NO, name);
+}
+
+void reset_phy(void)
+{
+ mv_phy_init("egiga0");
+
+#ifdef OPENRD_CLIENT
+ /* Kirkwood ethernet driver is written with the assumption that in case
+ * of multiple PHYs, their addresses are consecutive. But unfortunately
+ * in case of OpenRD-Client, PHY addresses are not consecutive.*/
+ miiphy_write("egiga1", 0xEE, 0xEE, 24);
+#endif
+
+#if defined(OPENRD_CLIENT) || defined(OPENRD_ULTIMATE)
+ /* configure and initialize both PHY's */
+ mv_phy_init("egiga1");
+#endif
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/openrd/openrd.h b/board/Marvell/openrd/openrd.h
new file mode 100644
index 0000000..2fe2e19
--- /dev/null
+++ b/board/Marvell/openrd/openrd.h
@@ -0,0 +1,50 @@
+/*
+ * Modified Simon's work to deal with all the three variants of
+ * OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate)
+ *
+ * eInfochips <www.einfochips.com>
+ * Modified-by: Tanmay Upadhyay <tanmay.upadhyay at einfochips.com>
+ *
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __OPENRD_H
+#define __OPENRD_H
+
+#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */
+#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */
+#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
+#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
+
+/* PHY related */
+#define MAC_CTRL_REG 21
+#define PGADR_REG 22
+#define RGMII_TXTM_CTRL (1 << 4)
+#define RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __OPENRD_H */
diff --git a/board/Marvell/openrd_base/Makefile b/board/Marvell/openrd_base/Makefile
deleted file mode 100644
index d6d0ed3..0000000
--- a/board/Marvell/openrd_base/Makefile
+++ /dev/null
@@ -1,56 +0,0 @@
-#
-# (C) Copyright 2009
-# Net Insight <www.netinsight.net>
-# Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
-#
-# Based on sheevaplug:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).o
-
-COBJS := openrd_base.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(call cmd_link_o_target, $(OBJS) $(SOBJS))
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak .depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/Marvell/openrd_base/kwbimage.cfg b/board/Marvell/openrd_base/kwbimage.cfg
deleted file mode 100644
index 757eb28..0000000
--- a/board/Marvell/openrd_base/kwbimage.cfg
+++ /dev/null
@@ -1,168 +0,0 @@
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-# Refer docs/README.kwimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM nand
-NAND_ECC_MODE default
-NAND_PAGE_SIZE 0x0800
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b1b9b
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000c30 # DDR Configuration register
-# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
-# bit3-0: TRAS lsbs
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x000000cc # DDR Address Control
-# bit1-0: 00, Cs0width=x8
-# bit3-2: 11, Cs0size=1Gb
-# bit5-4: 00, Cs1width=x8
-# bit7-6: 11, Cs1size=1Gb
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000C52 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000042 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 1, DDR drive strength reduced
-# bit2: 0, DDR ODT control lsd (disabled)
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, (disabled)
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 0
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x0F, Size (i.e. 256MB)
-
-DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
-DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
-
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
-# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
-# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
-# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
-# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-
-DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
-# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
-# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
-# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
-# bit14: 1, M_STARTBURST_IN ODT: Enabled
-# bit15: 1, DDR IO ODT Unit: Use ODT block
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/Marvell/openrd_base/openrd_base.c b/board/Marvell/openrd_base/openrd_base.c
deleted file mode 100644
index 10109c1..0000000
--- a/board/Marvell/openrd_base/openrd_base.c
+++ /dev/null
@@ -1,153 +0,0 @@
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
- *
- * Based on sheevaplug.c:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
- */
-
-#include <common.h>
-#include <miiphy.h>
-#include <asm/arch/kirkwood.h>
-#include <asm/arch/mpp.h>
-#include "openrd_base.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- /*
- * default gpio configuration
- * There are maximum 64 gpios controlled through 2 sets of registers
- * the below configuration configures mainly initial LED status
- */
- kw_config_gpio(OPENRD_OE_VAL_LOW,
- OPENRD_OE_VAL_HIGH,
- OPENRD_OE_LOW, OPENRD_OE_HIGH);
-
- /* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
- MPP0_NF_IO2,
- MPP1_NF_IO3,
- MPP2_NF_IO4,
- MPP3_NF_IO5,
- MPP4_NF_IO6,
- MPP5_NF_IO7,
- MPP6_SYSRST_OUTn,
- MPP7_GPO,
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP12_SD_CLK,
- MPP13_SD_CMD, /* Alt UART1_TXD */
- MPP14_SD_D0, /* Alt UART1_RXD */
- MPP15_SD_D1,
- MPP16_SD_D2,
- MPP17_SD_D3,
- MPP18_NF_IO0,
- MPP19_NF_IO1,
- MPP20_GE1_0,
- MPP21_GE1_1,
- MPP22_GE1_2,
- MPP23_GE1_3,
- MPP24_GE1_4,
- MPP25_GE1_5,
- MPP26_GE1_6,
- MPP27_GE1_7,
- MPP28_GPIO,
- MPP29_TSMP9,
- MPP30_GE1_10,
- MPP31_GE1_11,
- MPP32_GE1_12,
- MPP33_GE1_13,
- MPP34_GPIO, /* UART1 / SD sel */
- MPP35_TDM_CH0_TX_QL,
- MPP36_TDM_SPI_CS1,
- MPP37_TDM_CH2_TX_QL,
- MPP38_TDM_CH2_RX_QL,
- MPP39_AUDIO_I2SBCLK,
- MPP40_AUDIO_I2SDO,
- MPP41_AUDIO_I2SLRC,
- MPP42_AUDIO_I2SMCLK,
- MPP43_AUDIO_I2SDI,
- MPP44_AUDIO_EXTCLK,
- MPP45_TDM_PCLK,
- MPP46_TDM_FS,
- MPP47_TDM_DRX,
- MPP48_TDM_DTX,
- MPP49_TDM_CH0_RX_QL,
- 0
- };
-
- kirkwood_mpp_conf(kwmpp_config);
- return 0;
-}
-
-int board_init(void)
-{
- /*
- * arch number of board
- */
- gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
- return 0;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-/* Configure and enable MV88E1116 PHY */
-void reset_phy(void)
-{
- u16 reg;
- u16 devadr;
- char *name = "egiga0";
-
- if (miiphy_set_current_dev(name))
- return;
-
- /* command to read PHY dev address */
- if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
- printf("Err..%s could not read PHY dev address\n",
- __FUNCTION__);
- return;
- }
-
- /*
- * Enable RGMII delay on Tx and Rx for CPU port
- * Ref: sec 4.7.2 of chip datasheet
- */
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
- miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
- reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
- miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
- /* reset the phy */
- miiphy_reset(name, devadr);
-
- printf("88E1116 Initialized on %s\n", name);
-}
-#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/openrd_base/openrd_base.h b/board/Marvell/openrd_base/openrd_base.h
deleted file mode 100644
index f3daf17..0000000
--- a/board/Marvell/openrd_base/openrd_base.h
+++ /dev/null
@@ -1,46 +0,0 @@
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
- *
- * Based on sheevaplug.h:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
- */
-
-#ifndef __OPENRD_BASE_H
-#define __OPENRD_BASE_H
-
-#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */
-#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */
-#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
-#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
-
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG 10
-#define MV88E1116_CPRSP_CR3_REG 21
-#define MV88E1116_MAC_CTRL_REG 21
-#define MV88E1116_PGADR_REG 22
-#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
-
-#endif /* __OPENRD_BASE_H */
diff --git a/boards.cfg b/boards.cfg
index c977528..4334630 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -96,7 +96,9 @@ davinci_sonata arm arm926ejs sonata davinci
suen3 arm arm926ejs km_arm keymile kirkwood
guruplug arm arm926ejs - Marvell kirkwood
mv88f6281gtw_ge arm arm926ejs - Marvell kirkwood
-openrd_base arm arm926ejs - Marvell kirkwood
+openrd_base arm arm926ejs openrd Marvell kirkwood
+openrd_client arm arm926ejs openrd Marvell kirkwood
+openrd_ultimate arm arm926ejs openrd Marvell kirkwood
rd6281a arm arm926ejs - Marvell kirkwood
sheevaplug arm arm926ejs - Marvell kirkwood
dockstar arm arm926ejs - Seagate kirkwood
diff --git a/include/configs/openrd.h b/include/configs/openrd.h
new file mode 100644
index 0000000..850dbae
--- /dev/null
+++ b/include/configs/openrd.h
@@ -0,0 +1,115 @@
+/*
+ * Modified openrd_base.h to deal with all the three variants of
+ * OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate)
+ *
+ * eInfochips <www.einfochips.com>
+ * Modified-by: Tanmay Upadhyay <tanmay.upadhyay at einfochips.com>
+ *
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_OPENRD_H
+#define _CONFIG_OPENRD_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_OPENRD_BASE /* Machine type */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_IDE
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x60000
+#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define MTDIDS_DEFAULT "nand0=nand_mtd"
+#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),"\
+ "0x400000 at 0x100000(uImage),"\
+ "0x1fb00000 at 0x500000(rootfs)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
+ "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
+ "mtdids="MTDIDS_DEFAULT"\0" \
+ "mtdparts="MTDPARTS_DEFAULT"\0"
+
+/*
+ * SATA Driver configuration
+ */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
+#endif /*CONFIG_MVSATA_IDE*/
+
+/* board_early_init_f function in openrd.c initializes all MPP settings */
+#define CONFIG_BOARD_EARLY_INIT_F
+#endif /* _CONFIG_OPENRD_H */
diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h
index cfdd09c..4f9ea80 100644
--- a/include/configs/openrd_base.h
+++ b/include/configs/openrd_base.h
@@ -1,4 +1,10 @@
/*
+ * Modified Simon's work to deal with all the three variants of
+ * OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate)
+ *
+ * eInfochips <www.einfochips.com>
+ * Modified-by: Tanmay Upadhyay <tanmay.upadhyay at einfochips.com>
+ *
* (C) Copyright 2009
* Net Insight <www.netinsight.net>
* Written-by: Simon Kagstrom <simon.kagstrom at netinsight.net>
@@ -30,91 +36,21 @@
#ifndef _CONFIG_OPENRD_BASE_H
#define _CONFIG_OPENRD_BASE_H
-/*
- * Version number information
- */
-#define CONFIG_IDENT_STRING "\nOpenRD_base"
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
-#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
-#define CONFIG_KW88F6281 1 /* SOC Name */
-#define CONFIG_MACH_OPENRD_BASE /* Machine type */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-
-/*
- * Commands configuration
- */
-#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
-#include <config_cmd_default.h>
-#define CONFIG_CMD_AUTOSCRIPT
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_IDE
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-/*
- * Environment variables configurations
- */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_ENV_IS_IN_NAND 1
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
-#else
-#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
-#endif
-/*
- * max 4k env size is enough, but in case of nand
- * it has to be rounded to sector size
- */
-#define CONFIG_ENV_SIZE 0x20000 /* 128k */
-#define CONFIG_ENV_ADDR 0x60000
-#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
-
-/*
- * Default environment variables
- */
-#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
- "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
- "${x_bootcmd_usb}; bootm 0x6400000;"
+#include <configs/openrd.h>
-#define MTDIDS_DEFAULT "nand0=nand_mtd"
-#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),"\
- "0x400000 at 0x100000(uImage),"\
- "0x1fb00000 at 0x500000(rootfs)"
+#define CONFIG_IDENT_STRING "\nOpenRD-Base"
-#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
- "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
- "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
- "x_bootcmd_usb=usb start\0" \
- "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
- "mtdids="MTDIDS_DEFAULT"\0" \
- "mtdparts="MTDPARTS_DEFAULT"\0"
+/* Machine type */
+#define MACH_TYPE_OPENRD MACH_TYPE_OPENRD_BASE
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR 0x8
+/* enable port 0 only */
+#define CONFIG_MVGBE_PORTS {1, 0}
+#define CONFIG_PHY_BASE_ADR 0x8
+#define PHY_NO "88E1116"
#endif /* CONFIG_CMD_NET */
-/*
- * SATA Driver configuration
- */
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
-#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
-#endif /*CONFIG_MVSATA_IDE*/
-
#endif /* _CONFIG_OPENRD_BASE_H */
diff --git a/include/configs/openrd_client.h b/include/configs/openrd_client.h
new file mode 100644
index 0000000..98d516a
--- /dev/null
+++ b/include/configs/openrd_client.h
@@ -0,0 +1,50 @@
+/*
+ * Created to deal with all the three variants of OpenRD boards
+ * (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate)
+ *
+ * eInfochips <www.einfochips.com>
+ * Written-by: Tanmay Upadhyay <tanmay.upadhyay at einfochips.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_OPENRD_CLIENT_H
+#define _CONFIG_OPENRD_CLIENT_H
+
+#include <configs/openrd.h>
+
+#define CONFIG_IDENT_STRING "\nOpenRD-Client"
+
+/* Machine type */
+#define MACH_TYPE_OPENRD MACH_TYPE_OPENRD_CLIENT
+
+/* board/openrd/openrd.c needs this */
+#define OPENRD_CLIENT
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+/* enable port 0 only */
+#define CONFIG_MVGBE_PORTS {1, 1}
+#define CONFIG_PHY_BASE_ADR 0x8
+#define PHY_NO "88E1116"
+#endif /* CONFIG_CMD_NET */
+
+#endif /* _CONFIG_OPENRD_CLIENT_H */
diff --git a/include/configs/openrd_ultimate.h b/include/configs/openrd_ultimate.h
new file mode 100644
index 0000000..4d20717
--- /dev/null
+++ b/include/configs/openrd_ultimate.h
@@ -0,0 +1,50 @@
+/*
+ * Created to deal with all the three variants of OpenRD boards
+ * (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate)
+ *
+ * eInfochips <www.einfochips.com>
+ * Written-by: Tanmay Upadhyay <tanmay.upadhyay at einfochips.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_OPENRD_ULTIMATE_H
+#define _CONFIG_OPENRD_ULTIMATE_H
+
+#include <configs/openrd.h>
+
+#define CONFIG_IDENT_STRING "\nOpenRD-Ultimate"
+
+/* Machine type */
+#define MACH_TYPE_OPENRD MACH_TYPE_OPENRD_ULTIMATE
+
+/* board/openrd/openrd.c needs this */
+#define OPENRD_ULTIMATE
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+/* enable port 0 only */
+#define CONFIG_MVGBE_PORTS {1, 1}
+#define CONFIG_PHY_BASE_ADR 0x0
+#define PHY_NO "88E1121"
+#endif /* CONFIG_CMD_NET */
+
+#endif /* _CONFIG_OPENRD_ULTIMATE_H */
-- 1.7.4
More information about the U-Boot
mailing list