[U-Boot] Uboot can't start kernel after change from version 2009.01 to 2010.09

[Maik Hänig]

Dear Reinhard Meyer,

I tried it with:

setenv bootargs root=/dev/mtdblock9 rootfstype=jffs2 console=ttyS4 
ETHADDR=$(ethaddr) RUNNING=$(runningimage) CFGFS=mtdblock10;bootm 0x30060000

but nothing the error is still there. The console is set in the board 
init of the linux kernel.

I changed only the uboot verion. The linux kernel and the rootfilesystem 
are the same.


Mit freundlichen Grüßen

Maik Hänig

Am 25.01.2011 12:03, schrieb Maik Hänig:
> Dear Reinhard,
>
> sorry I copied the wrong log:
>
> U-Boot 2010.09 (Jan 24 2011 - 17:45:54)
>
> I2C:   ready
> DRAM:  64 MiB
> Flash: 32 MiB
> In:    serial
> Out:   serial
> Err:   serial
> Hit any key to stop autoboot:  0
> ## Booting kernel from Legacy Image at 30060000 ...
>      Image Name:   Linux Kernel
>      Image Type:   ARM Linux Kernel Image (gzip compressed)
>      Data Size:    1084127 Bytes = 1 MiB
>      Load Address: 20008000
>      Entry Point:  20008000
>      Verifying Checksum ... OK
>      Uncompressing Kernel Image ... OK
>
> Starting kernel ...
>
> I have to kernel Images in flash. The bootcmd is copied from printenv.
> With the uboot version 2009.01 it works well. Is it nessesary to set a
> console parameter in the bootcmd in uboot version 2010.09?
>
>
> Mit freundlichen Grüßen
>
> Maik Hänig
>
> Am 25.01.2011 11:54, schrieb Reinhard Meyer:
>> Dear Maik Hänig,
>>> Hi,
>>>
>>>
>>> I change my uboot version and after it the uboot don't starts the same
>>> linux kernel:
>>>
>>> ## Booting kernel from Legacy Image at 10060000 ...
>> _________________________________________????????
>>>       Image Name:   Linux Kernel
>>>       Image Type:   ARM Linux Kernel Image (gzip compressed)
>>>       Data Size:    1178673 Bytes = 1.1 MiB
>>>       Load Address: 20008000
>>>       Entry Point:  20008000
>>>       Verifying Checksum ... OK
>>>       Uncompressing Kernel Image ... OK
>>>
>>> Starting kernel ...
>>>
>>> *****LOG END*****
>>>
>>>
>>> It's a board simular to the at91rm9200dk. I start the kernel with
>>>
>>> bootcmd2=setenv bootargs root=/dev/mtdblock9 rootfstype=squashfs
>>> ETHADDR=$(ethaddr) RUNNING=$(runningimage) CFGFS=mtdblock10;bootm 0x30060000
>> ______________________________________________________________________????????
>>>
>>> run bootcmd2
>>
>> First, I don't understand why those two addresses are not the same.
>>
>> Then, are you sure your "bootcmd2" ist really what you think it is?
>> Try a "printenv" and see whats really there.
>>
>> Should you not have a "console=xxx" in your kernel parameters?
>>
>> Besides once "Starting kernel ..." shows, u-boot is about to give control
>> to the kernel, all future output would be from the kernel itself, probably
>> needing a sane "console=xxx" parameter.
>>
>> Best Regards,
>> Reinhard
>>
>>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
>