[U-Boot] [PATCH v3 0/3] arm, davinci: add am1808 based enbw_cmc board

Heiko Schocher hs at denx.de
Mon Nov 28 11:44:46 CET 2011


repost from:
[U-Boot] [PATCH v2 0/3] arm, davinci: add am1808 based enbw_cmc board
http://lists.denx.de/pipermail/u-boot/2011-October/104399.html

Following patches are needed for this patchset
- patchset from Christian Riesch:
[U-Boot] [PATCH v3 00/15] Add an SPL to boot the da850evm from SPI
http://lists.denx.de/pipermail/u-boot/2011-November/111182.html

- [U-Boot,1/2] arm, arm926ejs: always do cpu critical inits
patchwork.ozlabs.org/patch/124787/

- [U-Boot] arm, fdt: update ethernet mac address before booting Linux
http://patchwork.ozlabs.org/patch/114736/

- [U-Boot] : davinci: Replace CONFIG_PRELOADER with CONFIG_SPL_BUILD in board/davinci/common/misc.c
http://patchwork.ozlabs.org/patch/114482/

checkpatch:
total: 0 errors, 0 warnings, 75 lines checked

20111128_ml/0001-arm-davinci-move-davinci_rtc-struct-to-hardware.h.patch has no obvious style problems and is ready for submission.
total: 0 errors, 0 warnings, 18 lines checked

20111128_ml/0002-arm-davinci-da850-add-uart1-tx-rx-pinmux-config.patch has no obvious style problems and is ready for submission.
WARNING: Use #include <linux/gpio.h> instead of <asm/gpio.h>
#223: FILE: board/enbw/enbw_cmc/enbw_cmc.c:41:
+#include <asm/gpio.h>

WARNING: Use #include <linux/io.h> instead of <asm/io.h>
#229: FILE: board/enbw/enbw_cmc/enbw_cmc.c:47:
+#include <asm/io.h>

WARNING: simple_strtoul is obsolete, use kstrtoul instead
#610: FILE: board/enbw/enbw_cmc/enbw_cmc.c:428:
+               sprintf(buf, "%ld", simple_strtoul(s, NULL, 10) + 1);

ERROR: Macros with multiple statements should be enclosed in a do - while loop
#951: FILE: include/configs/enbw_cmc.h:99:
+#define CONFIG_DTT_SENSORS     {0}     /* Sensor addresses             */

total: 1 errors, 3 warnings, 1168 lines checked

20111128_ml/0003-arm-davinci-add-support-for-am1808-based-enbw_cmc-bo.patch has style problems, please review.

If any of these errors are false positives, please report
them to the maintainer, see CHECKPATCH in MAINTAINERS.

Cc: Paulraj Sandeep <s-paulraj at ti.com>
Cc: Albert ARIBAUD <albert.u.boot at aribaud.net>
Cc: Igor Grinberg <grinberg at compulab.co.il>
Cc: Christian Riesch <christian.riesch at omicron.at>

Heiko Schocher (3):
  arm, davinci: move davinci_rtc struct to hardware.h
  arm, davinci, da850: add uart1 tx rx pinmux config
  arm, davinci: add support for am1808 based enbw_cmc board

 MAINTAINERS                                     |    1 +
 arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c   |    5 +
 arch/arm/include/asm/arch-davinci/hardware.h    |   39 ++
 arch/arm/include/asm/arch-davinci/pinmux_defs.h |    1 +
 board/enbw/enbw_cmc/Makefile                    |   51 ++
 board/enbw/enbw_cmc/enbw_cmc.c                  |  652 +++++++++++++++++++++++
 boards.cfg                                      |    1 +
 drivers/rtc/davinci.c                           |   26 -
 include/configs/enbw_cmc.h                      |  451 ++++++++++++++++
 9 files changed, 1201 insertions(+), 26 deletions(-)
 create mode 100644 board/enbw/enbw_cmc/Makefile
 create mode 100644 board/enbw/enbw_cmc/enbw_cmc.c
 create mode 100644 include/configs/enbw_cmc.h

-- 
1.7.6.4



More information about the U-Boot mailing list