[U-Boot] [PATCH 3/9] imx: fec: Resolve speed before configuring gasket
Timo Ketola
timo at exertus.fi
Fri Apr 13 13:20:55 CEST 2012
Gasket needs a different configuration for 10BaseT than for higher speeds.
Signed-off-by: Timo Ketola <timo at exertus.fi>
---
drivers/net/fec_mxc.c | 43 ++++++++++++++++++++++++-------------------
1 files changed, 24 insertions(+), 19 deletions(-)
diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
index 824a199..48a69d4 100644
--- a/drivers/net/fec_mxc.c
+++ b/drivers/net/fec_mxc.c
@@ -440,6 +440,22 @@ static int fec_open(struct eth_device *edev)
*/
writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_ETHER_EN,
&fec->eth->ecntrl);
+#ifdef CONFIG_PHYLIB
+ if (!fec->phydev)
+ fec_eth_phy_config(edev);
+ if (fec->phydev) {
+ /* Start up the PHY */
+ phy_startup(fec->phydev);
+ speed = fec->phydev->speed;
+ } else {
+ speed = _100BASET;
+ }
+#else
+ miiphy_wait_aneg(edev);
+ speed = miiphy_speed(edev->name, fec->phy_id);
+ miiphy_duplex(edev->name, fec->phy_id);
+#endif
+
#if defined(CONFIG_MX25) || defined(CONFIG_MX53)
udelay(100);
/*
@@ -453,9 +469,14 @@ static int fec_open(struct eth_device *edev)
while (readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY)
udelay(2);
-#if !defined(CONFIG_MII)
- /* configure gasket for RMII, 50 MHz, no loopback, and no echo */
- writew(MIIGSK_CFGR_IF_MODE_RMII, &fec->eth->miigsk_cfgr);
+#if defined(CONFIG_RMII)
+ if (speed != _10BASET)
+ /* configure gasket for RMII, 50MHz, no loopback, and no echo */
+ writew(MIIGSK_CFGR_IF_MODE_RMII, &fec->eth->miigsk_cfgr);
+ else
+ /* configure gasket for RMII, 5MHz, no loopback, and no echo */
+ writew(MIIGSK_CFGR_IF_MODE_RMII | MIIGSK_CFGR_FRCONT,
+ &fec->eth->miigsk_cfgr);
#else
/* configure gasket for MII, no loopback, and no echo */
writew(MIIGSK_CFGR_IF_MODE_MII, &fec->eth->miigsk_cfgr);
@@ -474,22 +495,6 @@ static int fec_open(struct eth_device *edev)
}
#endif
-#ifdef CONFIG_PHYLIB
- if (!fec->phydev)
- fec_eth_phy_config(edev);
- if (fec->phydev) {
- /* Start up the PHY */
- phy_startup(fec->phydev);
- speed = fec->phydev->speed;
- } else {
- speed = _100BASET;
- }
-#else
- miiphy_wait_aneg(edev);
- speed = miiphy_speed(edev->name, fec->phy_id);
- miiphy_duplex(edev->name, fec->phy_id);
-#endif
-
#ifdef FEC_QUIRK_ENET_MAC
{
u32 ecr = readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_SPEED;
--
1.7.5.4
More information about the U-Boot
mailing list