[U-Boot] [PATCH v3 0/7] tegra: Add NAND flash support

[Simon Glass]

This series adds NAND flash support to Tegra and enables it on Seaboard.

Included here is a proposed device tree binding with most of the properties
private to "nvidia,". The binding includes information about the NAND
controller as well as the connected NAND device. The Seaboard has a
Hynix HY27UF4G2B.

The driver supports ECC-based access and uses DMA and NAND acceleration
features of the Tegra SOC to provide access at reasonable speed.

Changes in v2:
- Add new patch to align default buffers in nand_base
- Added comment about the behaviour of the 'resp' register
- Call set_bus_width_page_size() at init to report errors earlier
- Change set_bus_width_page_size() to return an error when needed
- Change timing structure member to u32 to match device tree
- Check for supported bus width in board_nand_init()
- Fix tegra nand header file to remove BIT defines
- Implement a dummy nand_select_chip() instead of nand_hwcontro()
- Make nand_command() display an error on an unknown command
- Minor code tidy-ups in driver for style
- Move cache logic into a separate dma_prepare() function
- Remove CMD_TRANS_SIZE_BYTESx enum
- Remove space after casts
- Remove use of 'register' variables
- Rename struct nand_info to struct nand_drv to avoid nand_info_t confusion
- Support 4096 byte page devices, drop 1024 and 2048
- Tidy up nand_waitfor_cmd_completion() logic
- Update NAND binding to add "nvidia," prefix
- Use s32 for device tree integer values

Changes in v3:
- Add reg property for unit address (should be used for chip select)
- Change note in fdt binding about the need for a hardware-specific binding
- Fix up typos in fdt binding, and rename the file
- Update fdt binding to make everything Nvidia-specific

Jim Lin (1):
  tegra: nand: Add Tegra NAND driver

Simon Glass (6):
  nand: Try to align the default buffers
  fdt: Add debugging to fdtdec_get_int/addr()
  tegra: Add NAND support to funcmux
  tegra: fdt: Add NAND controller binding and definitions
  tegra: fdt: Add NAND definitions to fdt
  tegra: Enable NAND on Seaboard

 arch/arm/cpu/armv7/tegra2/funcmux.c                |    7 +
 arch/arm/dts/tegra20.dtsi                          |    6 +
 arch/arm/include/asm/arch-tegra2/funcmux.h         |    3 +
 arch/arm/include/asm/arch-tegra2/tegra2.h          |    1 +
 board/nvidia/dts/tegra2-seaboard.dts               |   16 +
 .../nand/nvidia,tegra20-nand.txt                   |   68 ++
 drivers/mtd/nand/Makefile                          |    1 +
 drivers/mtd/nand/nand_base.c                       |    3 +-
 drivers/mtd/nand/tegra2_nand.c                     | 1095 ++++++++++++++++++++
 drivers/mtd/nand/tegra2_nand.h                     |  257 +++++
 include/configs/seaboard.h                         |    9 +
 include/fdtdec.h                                   |    1 +
 include/linux/mtd/nand.h                           |    7 +-
 lib/fdtdec.c                                       |   23 +-
 14 files changed, 1487 insertions(+), 10 deletions(-)
 create mode 100644 doc/device-tree-bindings/nand/nvidia,tegra20-nand.txt
 create mode 100644 drivers/mtd/nand/tegra2_nand.c
 create mode 100644 drivers/mtd/nand/tegra2_nand.h

-- 
1.7.7.3