[U-Boot] [PATCH 2/2 v7] Add support for MINI2440 (s3c2440).

Marek Vasut marex at denx.de
Mon Apr 30 15:21:49 CEST 2012


Dear Gabriel Huau,

> Signed-off-by: Gabriel Huau <contact at huau-gabriel.fr>
> ---
> Changes for v2:
> 	- Coding style cleanup
> 	- Remove unnecessary files modification
> 	- Remove unnecessary board configuration set
> 
> Changes for v3:
> 	- Coding style cleanup
> 	- Move some macro definition from lowlevel_init.S
>         to a new header
> 	- Remove some "magic bloat" with I/O board initialization
> 	- Add a pll_delay and replace loop by it
> 	- Somme cleanup in the configuration file
> 	- Cancel modifications on an SoC specific header
> 	- Add my name to copyright
> 
> Changes for v4:
> 	- Move dram init to dram_init() instead low_levelinit
> 	- Remove u	-boot env from configuration file and change
>         the address of initial SP
> 	- Remove PLL init, now it's SoC specific
> 
> Changes for v5:
> 	- Clean up configuration file
> 	- Add a MAINTAINERS entry
> 	- Add a README.mini2440 file
> 	- Use gpio/iomux interface in case of magic numbers
> 	- Use get_ram_size()
> 
> Changes for v6:
> 	- Coding style cleanup
> 	- Remove some unused define in the board config
> 
> Changes for v7:
> 	- Cleanup coding style
> 	- Changement of the commit message
> 
>  MAINTAINERS                           |    4 +
>  board/friendlyarm/mini2440/Makefile   |   44 ++++++++
>  board/friendlyarm/mini2440/mini2440.c |  134 ++++++++++++++++++++++++
>  board/friendlyarm/mini2440/mini2440.h |  144 +++++++++++++++++++++++++
>  boards.cfg                            |    1 +
>  doc/README.mini2440                   |   28 +++++
>  include/configs/mini2440.h            |  186
> +++++++++++++++++++++++++++++++++ 7 files changed, 541 insertions(+)
>  create mode 100644 board/friendlyarm/mini2440/Makefile
>  create mode 100644 board/friendlyarm/mini2440/mini2440.c
>  create mode 100644 board/friendlyarm/mini2440/mini2440.h
>  create mode 100644 doc/README.mini2440
>  create mode 100644 include/configs/mini2440.h
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 708ded7..2611fb5 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -566,6 +566,10 @@ Unknown / orphaned boards:
>  #	Board		CPU						#
>  #########################################################################
> 
> +Gabriel HUAU <contact at huau-gabriel.fr>
> +
> +	mini2440	s3c2440
> +
>  Albert ARIBAUD <albert.u.boot at aribaud.net>
> 
>  	edminiv2	ARM926EJS (Orion5x SoC)
> diff --git a/board/friendlyarm/mini2440/Makefile
> b/board/friendlyarm/mini2440/Makefile new file mode 100644
> index 0000000..b88e569
> --- /dev/null
> +++ b/board/friendlyarm/mini2440/Makefile
> @@ -0,0 +1,44 @@
> +#
> +# (C) Copyright 2012
> +# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> +# MA 02111-1307 USA
> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB	= $(obj)lib$(BOARD).o
> +
> +COBJS	:= mini2440.o
> +
> +SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
> +OBJS	:= $(addprefix $(obj),$(COBJS))
> +SOBJS	:= $(addprefix $(obj),$(SOBJS))
> +
> +$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
> +	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
> +
> +#########################################################################
> +
> +# defines $(obj).depend target
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> +
> +#########################################################################
> diff --git a/board/friendlyarm/mini2440/mini2440.c
> b/board/friendlyarm/mini2440/mini2440.c new file mode 100644
> index 0000000..e97d981
> --- /dev/null
> +++ b/board/friendlyarm/mini2440/mini2440.c
> @@ -0,0 +1,134 @@
> +/*
> + * (C) Copyright 2002
> + * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
> + * Marius Groeger <mgroeger at sysgo.de>
> + *
> + * (C) Copyright 2002
> + * David Mueller, ELSOFT AG, <d.mueller at elsoft.ch>
> + *
> + * (C) Copyright 2009
> + * Michel Pollet <buserror at gmail.com>
> + *
> + * (C) Copyright 2012
> + * Gabriel Huau <contact at huau-gabriel.fr>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <common.h>
> +#include <asm/arch/s3c2440.h>
> +#include <asm/arch/iomux.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/io.h>
> +#include <asm/gpio.h>
> +#include <netdev.h>
> +#include "mini2440.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +static inline void pll_delay(unsigned long loops)
> +{
> +	__asm__ volatile ("1:\n"
> +	  "subs %0, %1, #1\n"
> +	  "bne 1b" : "=r" (loops) : "0" (loops));
> +}
> +
> +int board_early_init_f(void)
> +{
> +	struct s3c24x0_clock_power * const clk_power =
> +					s3c24x0_get_base_clock_power();
> +
> +	/* to reduce PLL lock time, adjust the LOCKTIME register */
> +	clk_power->locktime = 0xFFFFFF; /* Max PLL Lock time count */
> +	clk_power->clkdivn = CLKDIVN_VAL;
> +
> +	/* configure UPLL */
> +	clk_power->upllcon = ((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV);
> +	/* some delay between MPLL and UPLL */
> +	pll_delay(100);
> +
> +	/* configure MPLL */
> +	clk_power->mpllcon = ((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV);
> +
> +	/* some delay between MPLL and UPLL */
> +	pll_delay(10000);
> +
> +	return 0;
> +}
> +
> +/*
> + * Miscellaneous platform dependent initialisations
> + */
> +int board_init(void)
> +{
> +	struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio();
> +
> +	/* IOMUX Port H : UART Configuration */
> +	gpio->gphcon = IOMUXH_nCTS0 | IOMUXH_nRTS0 | IOMUXH_TXD0 | IOMUXH_RXD0 |
> +		IOMUXH_TXD1 | IOMUXH_RXD1 | IOMUXH_TXD2 | IOMUXH_RXD2;
> +
> +	gpio_direction_output(GPH8, 0);
> +	gpio_direction_output(GPH9, 0);
> +	gpio_direction_output(GPH10, 0);
> +
> +	/* adress of boot parameters */
> +	gd->bd->bi_boot_params = CONFIG_BOOT_PARAM_ADDR;
> +
> +	return 0;
> +}
> +
> +int dram_init(void)
> +{
> +	struct s3c24x0_memctl *memctl = s3c24x0_get_base_memctl();
> +
> +	/*
> +	 * Configuring bus width and timing
> +	 * Initialize clocks for each bank 0..5
> +	 * Bank 3 and 4 are used for DM9000
> +	 */
> +	writel(BANK_CONF, &memctl->bwscon);
> +	writel(B0_CONF, &memctl->bankcon[0]);
> +	writel(B1_CONF, &memctl->bankcon[1]);
> +	writel(B2_CONF, &memctl->bankcon[2]);
> +	writel(B3_CONF, &memctl->bankcon[3]);
> +	writel(B4_CONF, &memctl->bankcon[4]);
> +	writel(B5_CONF, &memctl->bankcon[5]);
> +
> +	/* Bank 6 and 7 are used for DRAM */
> +	writel(SDRAM_64MB, &memctl->bankcon[6]);
> +	writel(SDRAM_64MB, &memctl->bankcon[7]);
> +
> +	writel(MEM_TIMING, &memctl->refresh);
> +	writel(BANKSIZE_CONF, &memctl->banksize);
> +	writel(B6_MRSR, &memctl->mrsrb6);
> +	writel(B7_MRSR, &memctl->mrsrb7);
> +
> +	gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE,
> +			PHYS_SDRAM_SIZE);
> +	return 0;
> +}
> +
> +int board_eth_init(bd_t *bis)
> +{
> +#ifdef CONFIG_DRIVER_DM9000
> +	return dm9000_initialize(bis);
> +#else
> +	return 0;
> +#endif
> +}
> diff --git a/board/friendlyarm/mini2440/mini2440.h
> b/board/friendlyarm/mini2440/mini2440.h new file mode 100644
> index 0000000..db386ea
> --- /dev/null
> +++ b/board/friendlyarm/mini2440/mini2440.h
> @@ -0,0 +1,144 @@
> +#ifndef __MINI2440_BOARD_CONF_H__
> +#define __MINI2440_BOARD_CONF_H__
> +
> +/* PLL Parameters */
> +#define CLKDIVN_VAL	7
> +#define M_MDIV		0x7f
> +#define M_PDIV		0x2
> +#define M_SDIV		0x1
> +
> +#define U_M_MDIV	0x38
> +#define U_M_PDIV	0x2
> +#define U_M_SDIV	0x2
> +
> +/* BWSCON */
> +#define DW8				0x0
> +#define DW16			0x1
> +#define DW32			0x2
> +#define WAIT			(0x1<<2)
> +#define UBLB			(0x1<<3)
> +
> +#define B1_BWSCON		(DW32)
> +#define B2_BWSCON		(DW16)
> +#define B3_BWSCON		(DW16 + WAIT + UBLB)
> +#define B4_BWSCON		(DW16 + WAIT + UBLB)
> +#define B5_BWSCON		(DW16)
> +#define B6_BWSCON		(DW32)
> +#define B7_BWSCON		(DW32)
> +
> +/*
> + * Bank Configuration
> + */
> +#define B0_Tacs			0x0	/*  0clk */
> +#define B0_Tcos			0x0	/*  0clk */
> +#define B0_Tacc			0x7	/* 14clk */
> +#define B0_Tcoh			0x0	/*  0clk */
> +#define B0_Tah			0x0	/*  0clk */
> +#define B0_Tacp			0x0 /*  0clk */
> +#define B0_PMC			0x0	/* normal */
> +
> +#define B1_Tacs			0x0
> +#define B1_Tcos			0x0
> +#define B1_Tacc			0x7
> +#define B1_Tcoh			0x0
> +#define B1_Tah			0x0
> +#define B1_Tacp			0x0
> +#define B1_PMC			0x0
> +
> +#define B2_Tacs			0x0
> +#define B2_Tcos			0x0
> +#define B2_Tacc			0x7
> +#define B2_Tcoh			0x0
> +#define B2_Tah			0x0
> +#define B2_Tacp			0x0
> +#define B2_PMC			0x0
> +
> +#define B3_Tacs			0x0
> +#define B3_Tcos			0x3	/*  4clk */
> +#define B3_Tacc			0x7
> +#define B3_Tcoh			0x1	/*  1clk */
> +#define B3_Tah			0x3	/*  4clk */
> +#define B3_Tacp			0x0
> +#define B3_PMC			0x0
> +
> +#define B4_Tacs			0x0
> +#define B4_Tcos			0x3
> +#define B4_Tacc			0x7
> +#define B4_Tcoh			0x1
> +#define B4_Tah			0x3
> +#define B4_Tacp			0x0
> +#define B4_PMC			0x0
> +
> +#define B5_Tacs			0x0
> +#define B5_Tcos			0x0
> +#define B5_Tacc			0x7
> +#define B5_Tcoh			0x0
> +#define B5_Tah			0x0
> +#define B5_Tacp			0x0
> +#define B5_PMC			0x0
> +
> +/*
> + * SDRAM Configuration
> + */
> +#define SDRAM_MT		0x3	/* SDRAM */
> +#define SDRAM_Trcd		0x0	/* 2clk */
> +#define SDRAM_SCAN_9	0x1	/* 9bit */
> +#define SDRAM_SCAN_10	0x2	/* 10bit */
> +
> +#define SDRAM_64MB	((SDRAM_MT<<15) + (SDRAM_Trcd<<2) + (SDRAM_SCAN_9))
> +
> +/*
> + * Refresh Parameter
> + */
> +#define REFEN		0x1	/* Refresh enable */
> +#define TREFMD		0x0	/* CBR(CAS before RAS)/Auto refresh */
> +#define Trp			0x1	/* 3clk */
> +#define Trc			0x3	/* 7clk */
> +#define Tchr		0x0	/* unused */
> +#define REFCNT	1012 /* period=10.37us, HCLK=100Mhz, (2048 + 
1-10.37*100)
> */ +
> +/*
> + * MRSR Parameter
> + */
> +#define BL	0x0
> +#define BT	0x0
> +#define CL	0x3 /* 3 clocks */
> +#define TM	0x0
> +#define WBL	0x0
> +
> +/*
> + * BankSize Parameter
> + */
> +#define BK76MAP	0x2 /* 128MB/128MB */
> +#define SCLK_EN	0x1 /* SCLK active */
> +#define SCKE_EN	0x1 /* SDRAM power down mode enable */
> +#define BURST_EN	0x1 /* Burst enable */
> +
> +/*
> + * Register values
> + */
> +#define BANK_CONF ((0 + (B1_BWSCON<<4) + (B2_BWSCON<<8) + (B3_BWSCON<<12)
> + \ +			(B4_BWSCON<<16) + (B5_BWSCON<<20) + (B6_BWSCON<<24) + \
> +			(B7_BWSCON<<28)))
> +
> +#define B0_CONF	((B0_Tacs<<13) + (B0_Tcos<<11) + (B0_Tacc<<8) + \
> +		(B0_Tcoh<<6) + (B0_Tah<<4) + (B0_Tacp<<2) + (B0_PMC))
> +#define B1_CONF	((B1_Tacs<<13) + (B1_Tcos<<11) + (B1_Tacc<<8) + \
> +		(B1_Tcoh<<6) + (B1_Tah<<4) + (B1_Tacp<<2) + (B1_PMC))
> +#define B2_CONF	((B2_Tacs<<13) + (B2_Tcos<<11) + (B2_Tacc<<8) + \
> +		(B2_Tcoh<<6) + (B2_Tah<<4) + (B2_Tacp<<2) + (B2_PMC))
> +#define B3_CONF	((B3_Tacs<<13) + (B3_Tcos<<11) + (B3_Tacc<<8) + \
> +		(B3_Tcoh<<6) + (B3_Tah<<4) + (B3_Tacp<<2) + (B3_PMC))
> +#define B4_CONF	((B4_Tacs<<13) + (B4_Tcos<<11) + (B4_Tacc<<8) + \
> +		(B4_Tcoh<<6) + (B4_Tah<<4) + (B4_Tacp<<2) + (B4_PMC))
> +#define B5_CONF	((B5_Tacs<<13) + (B5_Tcos<<11) + (B5_Tacc<<8) + \
> +		(B5_Tcoh<<6) + (B5_Tah<<4) + (B5_Tacp<<2) + (B5_PMC))
> +
> +#define MEM_TIMING (REFEN<<23) + (TREFMD<<22) + (Trp<<20) + \
> +	(Trc<<18) + (Tchr<<16) + REFCNT
> +
> +#define BANKSIZE_CONF	(BK76MAP) + (SCLK_EN<<4) + (SCKE_EN<<5) +
> (BURST_EN<<7) +#define B6_MRSR			(CL<<4)
> +#define B7_MRSR			(CL<<4)
> +
> +#endif
> diff --git a/boards.cfg b/boards.cfg
> index 3cf75c3..93eeb3c 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -61,6 +61,7 @@ mx1ads                       arm         arm920t     -   
>                - scb9328                      arm         arm920t     -   
>                -              imx cm4008                       arm        
> arm920t     -                   -              ks8695 cm41xx              
>         arm         arm920t     -                   -              ks8695
> +mini2440                     arm         arm920t     mini2440           
> friendlyarm    s3c24x0 VCMA9                        arm         arm920t   
>  vcma9               mpl            s3c24x0 smdk2410                    
> arm         arm920t     -                   samsung        s3c24x0
> omap1510inn                  arm         arm925t     -                  
> ti diff --git a/doc/README.mini2440 b/doc/README.mini2440
> new file mode 100644
> index 0000000..311ca52
> --- /dev/null
> +++ b/doc/README.mini2440
> @@ -0,0 +1,28 @@
> +U-Boot for FriendlyARM Mini2440 (s3c2440)
> +
> +This file contains information for the port of U-Boot to FriendlyARM
> +mini2440
> +
> +All information about the board can be found on :
> +http://www.friendlyarm.net/products/mini2440
> +
> +To build u-boot : ./MAKEALL mini2440
> +
> +Overview :
> +--------
> +FriendlyARM Mini 2440 SBC (Single-Board Computer) with 400 MHz Samsung
> S3C2440 +ARM9 processor. The board measures 100 x 100 mm, ideal for
> learning about ARM9 +systems. It's a low cost board.
> +
> +Boot Methods :
> +------------
> +Mini2440 can boot from NOR or NAND.
> +
> +Build :
> +-----
> +./MAKEALL mini2440
> +
> +or
> +
> +make mini2440_config
> +make
> diff --git a/include/configs/mini2440.h b/include/configs/mini2440.h
> new file mode 100644
> index 0000000..fa7987c
> --- /dev/null
> +++ b/include/configs/mini2440.h
> @@ -0,0 +1,186 @@
> +/*
> + * (C) Copyright 2002
> + * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
> + * Marius Groeger <mgroeger at sysgo.de>
> + * Gary Jennejohn <gj at denx.de>
> + * David Mueller <d.mueller at elsoft.ch>
> + *
> + * (C) Copyright 2009-2010
> + * Michel Pollet <buserror at gmail.com>
> + *
> + * (C) Copyright 2012
> + * Gabriel Huau <contact at huau-gabriel.fr>
> + *
> + * Configuation settings for the MINI2440 board.
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define CONFIG_SYS_TEXT_BASE 0x0
> +#define CONFIG_S3C2440_GPIO
> +
> +/*
> + * High Level Configuration Options
> + */
> +#define CONFIG_ARM920T			/* This is an ARM920T Core	
*/
> +#define CONFIG_S3C24X0			/* in a SAMSUNG S3C24X0 SoC */
> +#define CONFIG_S3C2440			/* in a SAMSUNG S3C2440 SoC */
> +#define CONFIG_MINI2440			/* on a MIN2440 Board       */
> +
> +#define	MACH_TYPE_MINI2440	1999
> +#define	CONFIG_MACH_TYPE	MACH_TYPE_MINI2440
> +
> +/*
> + * We don't use lowlevel_init
> + */
> +#define CONFIG_SKIP_LOWLEVEL_INIT
> +#define CONFIG_BOARD_EARLY_INIT_F
> +
> +/*
> + * input clock of PLL
> + */
> +/* MINI2440 has 12.0000MHz input clock */
> +#define CONFIG_SYS_CLK_FREQ	12000000
> +
> +/*
> + * Size of malloc() pool
> + */
> +#define CONFIG_SYS_MALLOC_LEN	(CONFIG_ENV_SIZE + 2048*1024)
> +
> +/*
> + * Hardware drivers
> + */
> +#define CONFIG_DRIVER_DM9000
> +#define CONFIG_DRIVER_DM9000_NO_EEPROM
> +#define CONFIG_DM9000_BASE				0x20000300
> +#define DM9000_IO		CONFIG_DM9000_BASE
> +#define DM9000_DATA		(CONFIG_DM9000_BASE+4)
> +
> +/*
> + * select serial console configuration
> + */
> +#define CONFIG_S3C24X0_SERIAL
> +#define CONFIG_SERIAL1
> +
> +/*
> + * allow to overwrite serial and ethaddr
> + */
> +#define CONFIG_ENV_OVERWRITE
> +
> +/*
> + * Command definition
> + */
> +#include <config_cmd_default.h>
> +
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_PORTIO
> +#define CONFIG_CMD_REGINFO
> +#define CONFIG_CMD_SAVES
> +
> +/*
> + * Miscellaneous configurable options
> + */
> +#define	CONFIG_LONGHELP
> +#define	CONFIG_SYS_PROMPT	"MINI2440 => "
> +#define	CONFIG_SYS_CBSIZE	256
> +#define	CONFIG_SYS_PBSIZE	
(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
> +#define	CONFIG_SYS_MAXARGS	32
> +#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE

#define[tab] mixed with #define[space] ... also, please Cc Albert Aribaud for 
the next round, he'll likely pick this up.

> +
> +#define CONFIG_SYS_MEMTEST_START	0x30000000
> +#define CONFIG_SYS_MEMTEST_END		0x34000000	/* 64MB in DRAM	
*/
> +
> +/* default load address	*/
> +#define	CONFIG_SYS_LOAD_ADDR		0x32000000
> +
> +/* boot parameters address */
> +#define	CONFIG_BOOT_PARAM_ADDR		0x30000100
> +
> +/*
> + * the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need
> + * it to wrap 100 times (total 1562500) to get 1 sec.
> + */
> +#define	CONFIG_SYS_HZ			1562500
> +
> +/*
> + * valid baudrates
> + */
> +#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
> +#define CONFIG_BAUDRATE		115200
> +
> +/*
> + * Stack sizes
> + * The stack sizes are set up in start.S using the settings below
> + */
> +#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
> +#ifdef CONFIG_USE_IRQ
> +#define CONFIG_STACKSIZE_IRQ	(8*1024)	/* IRQ stack */
> +#define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
> +#endif
> +
> +/*
> + * Physical Memory Map
> + */
> +#define CONFIG_NR_DRAM_BANKS        1          /* we have 1 bank of DRAM
> */ +#define PHYS_SDRAM_SIZE             (64*1024*1024) /* 64MB of DRAM */
> +#define CONFIG_SYS_SDRAM_BASE       0x30000000
> +#define CONFIG_SYS_FLASH_BASE		0x0
> +
> +/*
> + * Stack should be on the SRAM because
> + * DRAM is not init
> + */
> +#define CONFIG_SYS_INIT_SP_ADDR		(0x40001000 - 
GENERATED_GBL_DATA_SIZE)
> +
> +/*
> + * NOR FLASH organization
> + * Now uses the standard CFI interface
> + * FLASH and environment organization
> + */
> +#define CONFIG_SYS_FLASH_CFI
> +#define CONFIG_FLASH_CFI_DRIVER
> +#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
> +#define CONFIG_SYS_MONITOR_BASE		0x0
> +/* max number of memory banks */
> +#define CONFIG_SYS_MAX_FLASH_BANKS	1
> +/* 512 * 4096 sectors, or 32 * 64k blocks */
> +#define CONFIG_SYS_MAX_FLASH_SECT	512
> +#define CONFIG_FLASH_SHOW_PROGRESS  1
> +
> +/*
> + * Config for NOR flash
> + */
> +#define CONFIG_ENV_IS_IN_FLASH
> +#define CONFIG_MY_ENV_OFFSET	0x40000
> +/* addr of environment */
> +#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 
CONFIG_MY_ENV_OFFSET)
> +/* 16k Total Size of Environment Sector */
> +#define CONFIG_ENV_SIZE		0x4000
> +
> +/* ATAG configuration */
> +#define CONFIG_INITRD_TAG
> +#define CONFIG_SETUP_MEMORY_TAGS
> +#define CONFIG_CMDLINE_TAG
> +#define CONFIG_CMDLINE_EDITING
> +#define CONFIG_AUTO_COMPLETE
> +
> +#endif	/* __CONFIG_H */


More information about the U-Boot mailing list