[U-Boot] [PATCH v5] at91: Add support for taskit AT91SAM9G20 boards.

Markus Hubig mhubig at imko.de
Mon Aug 6 19:32:44 CEST 2012


This adds support for the AT91SAM9G20 boards by taskit GmbH.
Both boards, Stamp9G20 and PortuxG20, are integrated in one
file. PortuxG20 is basically a SBC built around the Stamp9G20.

Signed-off-by: Markus Hubig <mhubig at imko.de>
Cc: Andreas Bießmann <andreas.devel at googlemail.com>
---
Changes for v2:
	- Added myself to the MAINTAINERS file.
	- Fixed a missleading comments.
	- Removed "Enable EMAC clock".
	- Enabled the at91sam9 hw watchdog.
	- Adding a timeout to PHY reset.
	- Uses the generic CONFIG_MACH_TYPE in stamp9g20.h.
	- Removed "mem=64M" from basicargs, its set by ATAGS.
	- Increased the space for the linux kernel to 6Mb.
	- Removed the "#ifdef CONFIG_MACB" switches.
	- Removed all tailing whitespaces in comments.
	- Removed CONFIG_USART3 its not used any more.
	- CONFIG_SYS_BAUDRATE_TABLE is now generic.
	- Removed the nowhere referenced CONFIG_STACKSIZE.
	- Removed the unessasary IRQ stuff.
	- Removed  CONFIG_RESET_PHY_R & reset_phy().

Changes for v3:
	- Moved all board specifig stuff into one block.
	- Fixed error in boards.cfg.
	- Added some comments about the PC5 and PC9 pins.
	- Making networking support configurable again.
	- Added autoload and autoboot to EXTRA_ENV_SETTINGS.
	- Fixed some minor issues with the timeout function.
	- Enabled CONFIG_CMD_SOURCE again.

Changes for v4:
	- Fixed some trailing whitespace style errors.
	- Enabled the STATUS_LED framework.
	- Fixed the URSTEN handling while PHY reset.

Changes for v5:
	- Enables the PIOA clock in coloured_LED_init.
	- Fixes some typos.
	- Fixes some 'parentheses' compiler warnings.
	- Unifies the calculations to use shifting '<<'.
	- Removes the obsolete CONFIG_ARCH_CPU_INIT.
	- Removes unused variable.
	- Fixes MAINTAINERS manipulation.

 MAINTAINERS                        |    8 +
 board/taskit/stamp9g20/Makefile    |   53 +++++++
 board/taskit/stamp9g20/led.c       |  138 +++++++++++++++++++
 board/taskit/stamp9g20/stamp9g20.c |  191 ++++++++++++++++++++++++++
 boards.cfg                         |    2 +
 include/configs/stamp9g20.h        |  266 ++++++++++++++++++++++++++++++++++++
 6 files changed, 658 insertions(+), 0 deletions(-)
 create mode 100644 board/taskit/stamp9g20/Makefile
 create mode 100644 board/taskit/stamp9g20/led.c
 create mode 100644 board/taskit/stamp9g20/stamp9g20.c
 create mode 100644 include/configs/stamp9g20.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 84413de..1c090db 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -243,6 +243,10 @@ Klaus Heydeck <heydeck at kieback-peter.de>
 	KUP4K		MPC855
 	KUP4X		MPC859
 
+Markus Hubig <mhubig at imko.de>
+
+	STAMP9G20	ARM926EJS
+
 Ilko Iliev <iliev at ronetix.at>
 
 	PM9261		AT91SAM9261
@@ -681,6 +685,10 @@ Vaibhav Hiremath <hvaibhav at ti.com>
 
 	am3517_evm	ARM ARMV7 (AM35x SoC)
 
+Markus Hubig <mhubig at imko.de>
+
+	STAMP9G20	ARM926EJS
+
 Grazvydas Ignotas <notasas at gmail.com>
 
 	omap3_pandora	ARM ARMV7 (OMAP3xx SoC)
diff --git a/board/taskit/stamp9g20/Makefile b/board/taskit/stamp9g20/Makefile
new file mode 100644
index 0000000..4f17a27
--- /dev/null
+++ b/board/taskit/stamp9g20/Makefile
@@ -0,0 +1,53 @@
+#
+# (C) Copyright 2003-2008
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# (C) Copyright 2008
+# Stelian Pop <stelian at popies.net>
+# Lead Tech Design <www.leadtechdesign.com>
+#
+# (C) Copyright 2012
+# Markus Hubig <mhubig at imko.de>
+# IMKO GmbH <www.imko.de>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y	+= stamp9g20.o
+COBJS-y	+= led.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/taskit/stamp9g20/led.c b/board/taskit/stamp9g20/led.c
new file mode 100644
index 0000000..197b4da
--- /dev/null
+++ b/board/taskit/stamp9g20/led.c
@@ -0,0 +1,138 @@
+/*
+ * Copyright (c) 2009 Wind River Systems, Inc.
+ * Tom Rix <Tom.Rix at windriver.com>
+ * (C) Copyright 2009
+ * Eric Benard <eric at eukrea.com>
+ *
+ * (C) Copyright 2012
+ * Markus Hubig <mhubig at imko.de>
+ * IMKO GmbH <www.imko.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91_pmc.h>
+#include <status_led.h>
+
+static unsigned int saved_state[3] = {STATUS_LED_OFF,
+	STATUS_LED_OFF, STATUS_LED_OFF};
+
+void coloured_LED_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+	/* Enable the clock */
+	writel(ATMEL_ID_PIOC, &pmc->pcer);
+
+	at91_set_gpio_output(CONFIG_RED_LED, 1);
+	at91_set_gpio_output(CONFIG_GREEN_LED, 1);
+	at91_set_gpio_output(CONFIG_YELLOW_LED, 1);
+
+	at91_set_gpio_value(CONFIG_RED_LED, 0);
+	at91_set_gpio_value(CONFIG_GREEN_LED, 1);
+	at91_set_gpio_value(CONFIG_YELLOW_LED, 0);
+}
+
+void red_led_on(void)
+{
+	at91_set_gpio_value(CONFIG_RED_LED, 1);
+	saved_state[STATUS_LED_RED] = STATUS_LED_ON;
+}
+
+void red_led_off(void)
+{
+	at91_set_gpio_value(CONFIG_RED_LED, 0);
+	saved_state[STATUS_LED_RED] = STATUS_LED_OFF;
+}
+
+void green_led_on(void)
+{
+	at91_set_gpio_value(CONFIG_GREEN_LED, 1);
+	saved_state[STATUS_LED_GREEN] = STATUS_LED_ON;
+}
+
+void green_led_off(void)
+{
+	at91_set_gpio_value(CONFIG_GREEN_LED, 0);
+	saved_state[STATUS_LED_GREEN] = STATUS_LED_OFF;
+}
+
+void yellow_led_on(void)
+{
+	at91_set_gpio_value(CONFIG_YELLOW_LED, 1);
+	saved_state[STATUS_LED_YELLOW] = STATUS_LED_ON;
+}
+
+void yellow_led_off(void)
+{
+	at91_set_gpio_value(CONFIG_YELLOW_LED, 0);
+	saved_state[STATUS_LED_YELLOW] = STATUS_LED_OFF;
+}
+
+void __led_init(led_id_t mask, int state)
+{
+	__led_set(mask, state);
+}
+
+void __led_toggle(led_id_t mask)
+{
+	if (STATUS_LED_RED == mask) {
+		if (STATUS_LED_ON == saved_state[STATUS_LED_RED])
+			red_led_off();
+		else
+			red_led_on();
+
+	} else if (STATUS_LED_GREEN == mask) {
+		if (STATUS_LED_ON == saved_state[STATUS_LED_GREEN])
+			green_led_off();
+		else
+			green_led_on();
+
+	} else if (STATUS_LED_YELLOW == mask) {
+		if (STATUS_LED_ON == saved_state[STATUS_LED_YELLOW])
+			yellow_led_off();
+		else
+			yellow_led_on();
+	}
+}
+
+void __led_set(led_id_t mask, int state)
+{
+	if (STATUS_LED_RED == mask) {
+		if (STATUS_LED_ON == state)
+			red_led_on();
+		else
+			red_led_off();
+
+	} else if (STATUS_LED_GREEN == mask) {
+		if (STATUS_LED_ON == state)
+			green_led_on();
+		else
+			green_led_off();
+
+	} else if (STATUS_LED_YELLOW == mask) {
+		if (STATUS_LED_ON == state)
+			yellow_led_on();
+		else
+			yellow_led_off();
+	}
+}
diff --git a/board/taskit/stamp9g20/stamp9g20.c b/board/taskit/stamp9g20/stamp9g20.c
new file mode 100644
index 0000000..5e07bf8
--- /dev/null
+++ b/board/taskit/stamp9g20/stamp9g20.c
@@ -0,0 +1,191 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian at popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * Achim Ehrlich <aehrlich at taskit.de>
+ * taskit GmbH <www.taskit.de>
+ *
+ * (C) Copyright 2012-
+ * Markus Hubig <mhubig at imko.de>
+ * IMKO GmbH <www.imko.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/at91sam9260_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/gpio.h>
+#include <watchdog.h>
+
+#ifdef CONFIG_MACB
+# include <net.h>
+# include <netdev.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void stamp9G20_nand_hw_init(void)
+{
+	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+	unsigned long csa;
+
+	/* Assign CS3 to NAND/SmartMedia Interface */
+	csa = readl(&matrix->ebicsa);
+	csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
+	writel(csa, &matrix->ebicsa);
+
+	/* Configure SMC CS3 for NAND/SmartMedia */
+	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+		AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+		&smc->cs[3].setup);
+	writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
+		AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
+		&smc->cs[3].pulse);
+	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
+		&smc->cs[3].cycle);
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+		AT91_SMC_MODE_EXNW_DISABLE |
+		AT91_SMC_MODE_DBW_8 |
+		AT91_SMC_MODE_TDF_CYCLE(2),
+		&smc->cs[3].mode);
+
+	/* Configure RDY/BSY */
+	at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+
+	/* Enable NandFlash */
+	at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+}
+
+#ifdef CONFIG_MACB
+static void stamp9G20_macb_hw_init(void)
+{
+	struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
+	struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC;
+	unsigned long erstl;
+
+	/* Enable the PHY Chip via PA26 on the Stamp 2 Adaptor */
+	at91_set_gpio_output(AT91_PIN_PA26, 0);
+
+	/*
+	 * Disable pull-up on:
+	 *	RXDV (PA17) => PHY normal mode (not Test mode)
+	 *	ERX0 (PA14) => PHY ADDR0
+	 *	ERX1 (PA15) => PHY ADDR1
+	 *	ERX2 (PA25) => PHY ADDR2
+	 *	ERX3 (PA26) => PHY ADDR3
+	 *	ECRS (PA28) => PHY ADDR4  => PHYADDR = 0x0
+	 *
+	 * PHY has internal pull-down
+	 */
+	writel(pin_to_mask(AT91_PIN_PA14) |
+		pin_to_mask(AT91_PIN_PA15) |
+		pin_to_mask(AT91_PIN_PA17) |
+		pin_to_mask(AT91_PIN_PA18) |
+		pin_to_mask(AT91_PIN_PA28),
+		&pioa->pudr);
+
+	erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK;
+
+	/* Need to reset PHY -> 500ms reset */
+	writel(AT91_RSTC_KEY | (AT91_RSTC_MR_ERSTL(13) &
+				~AT91_RSTC_MR_URSTEN), &rstc->mr);
+	writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr);
+
+	/* Wait for end of hardware reset */
+	unsigned long start = get_timer(0);
+	unsigned long timeout = 1000; /* 1000ms */
+
+	while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL)) {
+
+		/* avoid shutdown by watchdog */
+		WATCHDOG_RESET();
+		mdelay(10);
+
+		/* timeout for not getting stuck in an endless loop */
+		if (get_timer(start) >= timeout) {
+			puts("*** ERROR: Timeout waiting for PHY reset!\n");
+			break;
+		};
+	};
+
+	/* Restore NRST value */
+	writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN,
+		&rstc->mr);
+
+	/* Re-enable pull-up */
+	writel(pin_to_mask(AT91_PIN_PA14) |
+		pin_to_mask(AT91_PIN_PA15) |
+		pin_to_mask(AT91_PIN_PA17) |
+		pin_to_mask(AT91_PIN_PA18) |
+		pin_to_mask(AT91_PIN_PA28),
+		&pioa->puer);
+
+	/* Initialize EMAC=MACB hardware */
+	at91_macb_hw_init();
+}
+#endif /* CONFIG_MACB */
+
+int board_early_init_f(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+	/* Enable clocks for all PIOs */
+	writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
+		(1 << ATMEL_ID_PIOC), &pmc->pcer);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Adress of boot parameters */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+	/* Enable the serial interface */
+	at91_set_gpio_output(AT91_PIN_PC9, 1);
+	at91_seriald_hw_init();
+
+	stamp9G20_nand_hw_init();
+#ifdef CONFIG_MACB
+	stamp9G20_macb_hw_init();
+#endif
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size(
+		(void *)CONFIG_SYS_SDRAM_BASE,
+		CONFIG_SYS_SDRAM_SIZE);
+	return 0;
+}
+
+#ifdef CONFIG_MACB
+int board_eth_init(bd_t *bis)
+{
+	return macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00);
+}
+#endif /* CONFIG_MACB */
diff --git a/boards.cfg b/boards.cfg
index 1af87c0..8ee772b 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -120,6 +120,8 @@ cpu9G20_nand_128M            arm         arm926ejs   cpu9260             eukrea
 pm9261                       arm         arm926ejs   pm9261              ronetix        at91        pm9261:AT91SAM9261
 pm9263                       arm         arm926ejs   pm9263              ronetix        at91        pm9263:AT91SAM9263
 pm9g45                       arm         arm926ejs   pm9g45              ronetix        at91        pm9g45:AT91SAM9G45
+portuxg20                    arm         arm926ejs   stamp9g20           taskit         at91        stamp9g20:AT91SAM9G20,PORTUXG20
+stamp9g20                    arm         arm926ejs   stamp9g20           taskit         at91        stamp9g20:AT91SAM9G20
 cam_enc_4xx                  arm         arm926ejs   cam_enc_4xx         ait            davinci     cam_enc_4xx
 da830evm                     arm         arm926ejs   da8xxevm            davinci        davinci
 da850_am18xxevm              arm         arm926ejs   da8xxevm            davinci        davinci     da850evm:DA850_AM18X_EVM,MAC_ADDR_IN_EEPROM,SYS_I2C_EEPROM_ADDR_LEN=2,SYS_I2C_EEPROM_ADDR=0x50
diff --git a/include/configs/stamp9g20.h b/include/configs/stamp9g20.h
new file mode 100644
index 0000000..a2a0156
--- /dev/null
+++ b/include/configs/stamp9g20.h
@@ -0,0 +1,266 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian at popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * (C) Copyright 2010
+ * Achim Ehrlich <aehrlich at taskit.de>
+ * taskit GmbH <www.taskit.de>
+ *
+ * (C) Copyright 2012
+ * Markus Hubig <mhubig at imko.de>
+ * IMKO GmbH <www.imko.de>
+ *
+ * Configuation settings for the stamp9g20 CPU module.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * SoC must be defined first, before hardware.h is included.
+ * In this case SoC is defined in boards.cfg.
+ */
+#include <asm/hardware.h>
+
+/*
+ * Warning: changing CONFIG_SYS_TEXT_BASE requires adapting the initial boot
+ * program. Since the linker has to swallow that define, we must use a pure
+ * hex number here!
+ */
+#define CONFIG_SYS_TEXT_BASE		0x23f00000
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK	32768		/* slow clock xtal */
+#define CONFIG_SYS_AT91_MAIN_CLOCK	18432000	/* 18.432MHz crystal */
+#define CONFIG_SYS_HZ			1000		/* 1ms resolution */
+
+/* misc settings */
+#define CONFIG_CMDLINE_TAG		/* pass commandline to Kernel */
+#define CONFIG_SETUP_MEMORY_TAGS	/* pass memory defs to kernel */
+#define CONFIG_INITRD_TAG		/* pass initrd param to kernel */
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */
+#define CONFIG_BOARD_EARLY_INIT_f	/* call board_early_init_f() */
+#define CONFIG_DISPLAY_CPUINFO		/* display CPU Info at startup */
+
+/* setting board specific options */
+#ifdef CONFIG_PORTUXG20
+# define CONFIG_MACH_TYPE		MACH_TYPE_PORTUXG20
+# define CONFIG_MACB
+#else
+# define CONFIG_MACH_TYPE		MACH_TYPE_STAMP9G20
+#endif
+
+/*
+ * SDRAM: 1 bank, 64 MB, base address 0x20000000
+ * Already initialized before u-boot gets started.
+ */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		ATMEL_BASE_CS1
+#define CONFIG_SYS_SDRAM_SIZE		(64 << 20)
+
+/*
+ * Perform a SDRAM Memtest from the start of SDRAM
+ * till the beginning of the U-Boot position in RAM.
+ */
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_TEXT_BASE - 0x100000)
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN \
+	ROUND(3 * CONFIG_ENV_SIZE + (128 << 10), 0x1000)
+
+/*
+ * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
+ * leaving the correct space for initial global data structure above that
+ * address while providing maximum stack area below.
+ */
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
+/* NAND flash settings */
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		ATMEL_BASE_CS3
+#define CONFIG_SYS_NAND_DBW_8
+#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
+#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN	AT91_PIN_PC14
+#define CONFIG_SYS_NAND_READY_PIN	AT91_PIN_PC13
+
+/* general purpose I/O */
+#define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
+#define CONFIG_AT91_GPIO		/* enable the GPIO features */
+#define CONFIG_AT91_GPIO_PULLUP	1	/* keep pullups on peripheral pins */
+
+/* serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
+#define CONFIG_USART_ID			ATMEL_ID_SYS
+#define CONFIG_BAUDRATE			115200
+
+/* LED configuration */
+#define CONFIG_STATUS_LED
+#define CONFIG_BOARD_SPECIFIC_LED
+
+/* The LED PINs */
+#define CONFIG_RED_LED			AT91_PIN_PC5
+#define CONFIG_GREEN_LED		AT91_PIN_PC4
+#define CONFIG_YELLOW_LED		AT91_PIN_PC10
+
+#define STATUS_LED_RED			0
+#define STATUS_LED_GREEN		1
+#define STATUS_LED_YELLOW		2
+
+/* Red LED */
+#define STATUS_LED_BIT			STATUS_LED_RED
+#define STATUS_LED_STATE		STATUS_LED_OFF
+#define STATUS_LED_PERIOD		(CONFIG_SYS_HZ / 2)
+
+/* Green LED */
+#define STATUS_LED_BIT1			STATUS_LED_GREEN
+#define STATUS_LED_STATE1		STATUS_LED_ON
+#define STATUS_LED_PERIOD1		(CONFIG_SYS_HZ / 2)
+
+/* Yellow LED */
+#define STATUS_LED_BIT2			STATUS_LED_YELLOW
+#define STATUS_LED_STATE2		STATUS_LED_OFF
+#define STATUS_LED_PERIOD2		(CONFIG_SYS_HZ / 2)
+
+/* Boot status LED */
+#define STATUS_LED_BOOT			STATUS_LED_GREEN
+
+/*
+ * Ethernet configuration
+ *
+ * PortuxG20 has always ethernet but for Stamp9G20 you
+ * can enable it here if your baseboard features ethernet.
+ */
+
+/* #define CONFIG_MACB */
+
+#ifdef CONFIG_MACB
+# define CONFIG_RMII			/* use reduced MII inteface */
+# define CONFIG_NET_RETRY_COUNT	20      /* # of DHCP/BOOTP retries */
+
+/* BOOTP and DHCP options */
+# define CONFIG_BOOTP_BOOTFILESIZE
+# define CONFIG_BOOTP_BOOTPATH
+# define CONFIG_BOOTP_GATEWAY
+# define CONFIG_BOOTP_HOSTNAME
+# define CONFIG_NFSBOOTCOMMAND						\
+	"setenv autoload yes; setenv autoboot yes; "			\
+	"setenv bootargs ${basicargs} ${mtdparts} "			\
+	"root=/dev/nfs ip=dhcp nfsroot=${serverip}:/srv/nfs/rootfs; "	\
+	"dhcp"
+#endif /* CONFIG_MACB */
+
+/* Enable the watchdog */
+#define CONFIG_AT91SAM9_WATCHDOG
+#define CONFIG_HW_WATCHDOG
+
+/* USB configuration */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_SYS_USB_OHCI_REGS_BASE	ATMEL_UHP_BASE
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"at91sam9260"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
+
+/* General Boot Parameter */
+#define CONFIG_BOOTDELAY		3
+#define CONFIG_BOOTCOMMAND		"run flashboot"
+#define CONFIG_SYS_PROMPT		"U-Boot> "
+#define CONFIG_SYS_CBSIZE		256
+#define CONFIG_SYS_MAXARGS		16
+#define CONFIG_SYS_PBSIZE \
+	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+
+/*
+ * RAM Memory address where to put the
+ * Linux Kernel befor starting.
+ */
+#define CONFIG_SYS_LOAD_ADDR		0x22000000
+
+/*
+ * The NAND Flash partitions:
+ * ==========================================
+ * 0x0000000-0x001ffff -> 128k, bootstrap
+ * 0x0020000-0x005ffff -> 256k, u-boot
+ * 0x0060000-0x007ffff -> 128k, env1
+ * 0x0080000-0x009ffff -> 128k, env2 (backup)
+ * 0x0100000-0x06fffff ->   6M, kernel
+ * 0x0700000-0x8000000 -> 121M, RootFS
+ */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET		((128 + 256) << 10)
+#define CONFIG_ENV_OFFSET_REDUND	((128 + 256 + 128) << 10)
+#define CONFIG_ENV_SIZE			(128 << 10)
+
+/*
+ * Predefined environment variables.
+ * Usefull to define some easy to use boot commands.
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+									\
+	"basicargs=console=ttyS0,115200\0"				\
+									\
+	"mtdparts=mtdparts=atmel_nand:128k(bootstrap)ro,"		\
+		"256k(uboot)ro,128k(env1)ro,"				\
+		"128k(env2)ro,6M(linux),-(root)rw\0"			\
+									\
+	"flashboot=setenv bootargs ${basicargs} ${mtdparts} "		\
+		"root=/dev/mtdblock5 rootfstype=jffs2; "		\
+		"nand read 0x22000000 0x100000 0x600000; "		\
+		"bootm 22000000\0"					\
+									\
+	"sdboot=setenv bootargs ${basicargs} ${mtdparts} "		\
+		"root=/dev/mmcblk0p1 rootwait; "			\
+		"nand read 0x22000000 0x100000 0x600000; "		\
+		"bootm 22000000"
+
+/* Command line & features configuration */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_LED
+
+#ifdef CONFIG_MACB
+# define CONFIG_CMD_PING
+# define CONFIG_CMD_DHCP
+#else
+# undef CONFIG_CMD_BOOTD
+# undef CONFIG_CMD_NET
+# undef CONFIG_CMD_NFS
+#endif /* CONFIG_MACB */
+
+#endif /* __CONFIG_H */
-- 
1.7.7



More information about the U-Boot mailing list