[U-Boot] [PATCH 5/6] nand_spl: p1023rds: wait before enabling DDR controller

[Matthew McClintock]

We have a requirement to wait a period of time before enabling the
DDR controller

Signed-off-by: Matthew McClintock <msm at freescale.com>
---
 nand_spl/board/freescale/p1023rds/Makefile    |    6 +++++-
 nand_spl/board/freescale/p1023rds/nand_boot.c |   14 ++++++++++++--
 2 files changed, 17 insertions(+), 3 deletions(-)

diff --git a/nand_spl/board/freescale/p1023rds/Makefile b/nand_spl/board/freescale/p1023rds/Makefile
index 168e868..da43521 100644
--- a/nand_spl/board/freescale/p1023rds/Makefile
+++ b/nand_spl/board/freescale/p1023rds/Makefile
@@ -34,7 +34,8 @@ CFLAGS	+= -DCONFIG_NAND_SPL
 
 SOBJS	= start.o resetvec.o
 COBJS	= cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \
-	  nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o
+	  nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o \
+	  ../common.o
 
 SRCS	:= $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
 OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
@@ -114,6 +115,9 @@ ifneq ($(OBJTREE), $(SRCTREE))
 $(obj)nand_boot.c:
 	@rm -f $(obj)nand_boot.c
 	ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c $(obj)nand_boot.c
+$(obj)../common.c:
+	@rm -f $(obj)../common.c
+	ln -s $(SRCTREE)/nand_spl/board/freescale/common.c $(obj)../common.c
 endif
 
 #########################################################################
diff --git a/nand_spl/board/freescale/p1023rds/nand_boot.c b/nand_spl/board/freescale/p1023rds/nand_boot.c
index 0065c87..9309936 100644
--- a/nand_spl/board/freescale/p1023rds/nand_boot.c
+++ b/nand_spl/board/freescale/p1023rds/nand_boot.c
@@ -25,6 +25,7 @@
 #include <asm/io.h>
 #include <nand.h>
 #include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
 
 /* Fixed sdram init -- doesn't use serial presence detect. */
 void sdram_init(void)
@@ -53,12 +54,21 @@ void sdram_init(void)
 	out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL);
 	out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1);
 	out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2);
-	out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
+	/* Set, but do not enable the memory */
+	out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN);
+
+	asm volatile("sync;isync");
+	udelay(500);
+
+	/* Let the controller go */
+	out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN);
 }
 
+u32 bus_clk;
+
 void board_init_f(ulong bootflag)
 {
-	u32 plat_ratio, bus_clk;
+	u32 plat_ratio;
 	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
 
 	/* initialize selected port with appropriate baud rate */
-- 
1.7.9.7