[U-Boot] [PATCH 1/4] serial: Add Dragonfire serial driver
Joe Hershberger
joe.hershberger at gmail.com
Tue Aug 14 18:45:39 CEST 2012
Hi Michal,
On Tue, Aug 14, 2012 at 11:38 AM, Michal Simek <monstr at monstr.eu> wrote:
> On 08/14/2012 04:09 PM, Joe Hershberger wrote:
>>
>> Hi Michal,
>>
>> On Tue, Aug 14, 2012 at 6:42 AM, Michal Simek <monstr at monstr.eu> wrote:
>>>
>>> The driver is used on Xilinx Zynq platform.
>>>
>>> Signed-off-by: Michal Simek <monstr at monstr.eu>
>>> ---
>>> drivers/serial/Makefile | 1 +
>>> drivers/serial/serial_xpssuart.c | 218
>>> ++++++++++++++++++++++++++++++++++++++
>>> 2 files changed, 219 insertions(+), 0 deletions(-)
>>> create mode 100644 drivers/serial/serial_xpssuart.c
>>
>>
>> I think this would be clearer if it was named serial_zynq.c
>>
>>> diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
>>> index 65d0f23..81350d0 100644
>>> --- a/drivers/serial/Makefile
>>> +++ b/drivers/serial/Makefile
>>> @@ -56,6 +56,7 @@ COBJS-$(CONFIG_S3C44B0_SERIAL) += serial_s3c44b0.o
>>> COBJS-$(CONFIG_XILINX_UARTLITE) += serial_xuartlite.o
>>> COBJS-$(CONFIG_SANDBOX_SERIAL) += sandbox.o
>>> COBJS-$(CONFIG_SCIF_CONSOLE) += serial_sh.o
>>> +COBJS-$(CONFIG_XPSS_SERIAL) += serial_xpssuart.o
>>
>>
>> Replace every reference to "XPSS" with "ZYNQ".
>>
>>> ifndef CONFIG_SPL_BUILD
>>> COBJS-$(CONFIG_USB_TTY) += usbtty.o
>>> diff --git a/drivers/serial/serial_xpssuart.c
>>> b/drivers/serial/serial_xpssuart.c
>>> new file mode 100644
>>> index 0000000..3c6d838
>>> --- /dev/null
>>> +++ b/drivers/serial/serial_xpssuart.c
>>> @@ -0,0 +1,218 @@
>>> +/*
>>> + * U-Boot driver for Xilinx Dragonfire UART.
>>
>>
>> Use the released name "Zynq" not the old codename "Dragonfire".
>
>
> ok.
>
>
>>
>>> + *
>>> + * Copyright (C) 2012 Michal Simek <monstr at monstr.eu>
>>> + * Copyright (C) 2011-2012 Xilinx, Inc. All rights reserved.
>>> + *
>>> + * See file CREDITS for list of people who contributed to this
>>> + * project.
>>> + *
>>> + * This program is free software; you can redistribute it and/or
>>> + * modify it under the terms of the GNU General Public License as
>>> + * published by the Free Software Foundation; either version 2 of
>>> + * the License, or (at your option) any later version.
>>> + *
>>> + * This program is distributed in the hope that it will be useful,
>>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>>> + * GNU General Public License for more details.
>>> + *
>>> + * You should have received a copy of the GNU General Public License
>>> + * along with this program; if not, write to the Free Software
>>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>>> + * MA 02111-1307 USA
>>> + */
>>> +
>>> +#include <common.h>
>>> +#include <watchdog.h>
>>> +#include <asm/io.h>
>>> +#include <serial.h>
>>> +
>>> +#define XDFUART_SR_TXFULL 0x00000010 /* TX FIFO full */
>>> +#define XDFUART_SR_RXEMPTY 0x00000002 /* RX FIFO empty */
>>
>>
>> Replace all references to "XDFUART" with "ZYNQ_UART".
>
>
> agree.
>
>
>>
>>> +
>>> +#define XDFUART_CR_TX_EN 0x00000010 /* TX enabled */
>>> +#define XDFUART_CR_RX_EN 0x00000004 /* RX enabled */
>>> +#define XDFUART_CR_TXRST 0x00000002 /* TX logic reset */
>>> +#define XDFUART_CR_RXRST 0x00000001 /* RX logic reset */
>>> +
>>> +#define XDFUART_MR_PARITY_NONE 0x00000020 /* No parity mode */
>>> +
>>> +/* Some clock/baud constants */
>>> +#define XDFUART_BDIV 15 /* Default/reset BDIV value */
>>> +#define XDFUART_BASECLK 3125000L /* master / (bdiv + 1) */
>>> +
>>> +struct xdfuart {
>>> + u32 control; /* Control Register [8:0] */
>>> + u32 mode; /* Mode Register [10:0] */
>>> + u32 reserved1[4];
>>> + u32 baud_rate_gen; /* Baud Rate Generator [15:0] */
>>> + u32 reserved2[4];
>>> + u32 channel_sts; /* Channel Status [11:0] */
>>> + u32 tx_rx_fifo; /* FIFO [15:0] or [7:0] */
>>> + u32 baud_rate_divider; /* Baud Rate Divider [7:0] */
>>> +};
>>> +
>>> +static struct xdfuart *xdf_ports[4] = {
>>> +#ifdef CONFIG_XPSS_SERIAL_BASEADDR0
>>> + [0] = (struct xdfuart *)CONFIG_XPSS_SERIAL_BASEADDR0,
>>> +#endif
>>> +#ifdef CONFIG_XPSS_SERIAL_BASEADDR1
>>> + [1] = (struct xdfuart *)CONFIG_XPSS_SERIAL_BASEADDR1,
>>> +#endif
>>
>>
>> There are 2 UARTS in hard silicon.
>
>
> My fault.
>
>
> They should be supported with
>>
>> their known base addresses (0xE0000000 and 0xE0001000) here without
>> pushing that into the config header.
>
>
> I am not sure that hardcoding addresses here is the right thing to do.
> The main reason is that none has tested option that hard IPs can be
> also used from programmable logic. It means that this driver
> could be possible to use from Microblaze with address translation.
>
> No problem to setup these addresses in config file.
I accept that you can access these from microblaze, but I think that
will be the 1% use-case. You can make the base address overridable,
but use the ARM core address space by default and have them here
instead of copied to every config.
>>
>>> +#ifdef CONFIG_XPSS_SERIAL_BASEADDR2
>>> + [2] = (struct xdfuart *)CONFIG_XPSS_SERIAL_BASEADDR2,
>>> +#endif
>>> +#ifdef CONFIG_XPSS_SERIAL_BASEADDR3
>>> + [3] = (struct xdfuart *)CONFIG_XPSS_SERIAL_BASEADDR3,
>>> +#endif
>>> +};
>>> +
>>> +struct xdfuart_params {
>>> + u32 baudrate;
>>> + u32 clock;
>>> +};
>>> +
>>> +static struct xdfuart_params xdf_ports_param[4] = {
>>> +#if defined(CONFIG_XPSS_SERIAL_BAUDRATE0) &&
>>> defined(CONFIG_XPSS_SERIAL_CLOCK0)
>>> + [0].baudrate = CONFIG_XPSS_SERIAL_BAUDRATE0,
>>> + [0].clock = CONFIG_XPSS_SERIAL_CLOCK0,
>>> +#endif
>>> +#if defined(CONFIG_XPSS_SERIAL_BAUDRATE1) &&
>>> defined(CONFIG_XPSS_SERIAL_CLOCK1)
>>> + [1].baudrate = CONFIG_XPSS_SERIAL_BAUDRATE1,
>>> + [1].clock = CONFIG_XPSS_SERIAL_CLOCK1,
>>> +#endif
>>> +#if defined(CONFIG_XPSS_SERIAL_BAUDRATE2) &&
>>> defined(CONFIG_XPSS_SERIAL_CLOCK2)
>>> + [2].baudrate = CONFIG_XPSS_SERIAL_BAUDRATE2,
>>> + [2].clock = CONFIG_XPSS_SERIAL_CLOCK2,
>>> +#endif
>>> +#if defined(CONFIG_XPSS_SERIAL_BAUDRATE3) &&
>>> defined(CONFIG_XPSS_SERIAL_CLOCK3)
>>> + [3].baudrate = CONFIG_XPSS_SERIAL_BAUDRATE3,
>>> + [3].clock = CONFIG_XPSS_SERIAL_CLOCK3,
>>> +#endif
>>> +};
>>> +
>>> +/* Set up the baud rate in gd struct */
>>> +static void xdfuart_serial_setbrg(const int port)
>>> +{
>>> + /* Calculation results. */
>>> + unsigned int calc_bauderror, bdiv, bgen;
>>> + unsigned long calc_baud = 0;
>>> + unsigned long baud = xdf_ports_param[port].baudrate;
>>> + unsigned long clock = xdf_ports_param[port].clock;
>>> + struct xdfuart *regs = xdf_ports[port];
>>> +
>>> + /* master clock
>>> + * Baud rate = ------------------
>>> + * bgen * (bdiv + 1)
>>> + *
>>> + * Find acceptable values for baud generation.
>>> + */
>>> + for (bdiv = 4; bdiv < 255; bdiv++) {
>>> + bgen = clock / (baud * (bdiv + 1));
>>> + if (bgen < 2 || bgen > 65535)
>>> + continue;
>>> +
>>> + calc_baud = clock / (bgen * (bdiv + 1));
>>> +
>>> + /*
>>> + * Use first calculated baudrate with
>>> + * an acceptable (<3%) error
>>> + */
>>> + if (baud > calc_baud)
>>> + calc_bauderror = baud - calc_baud;
>>> + else
>>> + calc_bauderror = calc_baud - baud;
>>> + if (((calc_bauderror * 100) / baud) < 3)
>>> + break;
>>> + }
>>> +
>>> + writel(bdiv, ®s->baud_rate_divider);
>>> + writel(bgen, ®s->baud_rate_gen);
>>> +}
>>> +
>>> +/* Initialize the UART, with...some settings. */
>>> +static int xdfuart_serial_init(const int port)
>>> +{
>>> + struct xdfuart *regs = xdf_ports[port];
>>> +
>>> + if (!regs)
>>> + return -1;
>>> +
>>> + /* RX/TX enabled & reset */
>>> + writel(XDFUART_CR_TX_EN | XDFUART_CR_RX_EN | XDFUART_CR_TXRST | \
>>> + XDFUART_CR_RXRST,
>>> ®s->control);
>>> + writel(XDFUART_MR_PARITY_NONE, ®s->mode); /* 8 bit, no parity
>>> */
>>> + xdfuart_serial_setbrg(port);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static void xdfuart_serial_putc(const char c, const int port)
>>> +{
>>> + struct xdfuart *regs = xdf_ports[port];
>>> +
>>> + while ((readl(®s->channel_sts) & XDFUART_SR_TXFULL) != 0)
>>> + WATCHDOG_RESET();
>>> +
>>> + if (c == '\n') {
>>> + writel('\r', ®s->tx_rx_fifo);
>>> + while ((readl(®s->channel_sts) & XDFUART_SR_TXFULL) !=
>>> 0)
>>> + WATCHDOG_RESET();
>>> + }
>>> + writel(c, ®s->tx_rx_fifo);
>>> +}
>>> +
>>> +static void xdfuart_serial_puts(const char *s, const int port)
>>> +{
>>> + while (*s)
>>> + xdfuart_serial_putc(*s++, port);
>>> +}
>>> +
>>> +static int xdfuart_serial_tstc(const int port)
>>> +{
>>> + struct xdfuart *regs = xdf_ports[port];
>>> +
>>> + return (readl(®s->channel_sts) & XDFUART_SR_RXEMPTY) == 0;
>>> +}
>>> +
>>> +static int xdfuart_serial_getc(const int port)
>>> +{
>>> + struct xdfuart *regs = xdf_ports[port];
>>> +
>>> + while (!xdfuart_serial_tstc(port))
>>> + WATCHDOG_RESET();
>>> + return readl(®s->tx_rx_fifo);
>>> +}
>>> +
>>> +#if !defined(CONFIG_SERIAL_MULTI)
>>> +int serial_init(void)
>>> +{
>>> + return xdfuart_serial_init(0);
>>
>>
>> If there is no SERIAL_MULTI support, there should be a config to
>> select which one to use.
>
>
> Not right now but I will add it in the next patch.
> But yes, this ifdef shouldn't be here.
>
> Thanks,
> Michal
>
>
> --
> Michal Simek, Ing. (M.Eng)
> w: www.monstr.eu p: +42-0-721842854
> Maintainer of Linux kernel 2.6 Microblaze Linux - http://www.monstr.eu/fdt/
> Microblaze U-BOOT custodian
More information about the U-Boot
mailing list