[U-Boot] [PATCH 5/6 v2] arm:exynos4:universal: Use pinmux for mmc configuration

[Piotr Wilczek]

This patch use the pinmux for mmc configuration for Universal C210

Signed-off-by: Piotr Wilczek <p.wilczek at samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
CC: Minkyu Kang <mk7.kang at samsung.com>
---
Changes for v2:
- mmc initialisation using pinmux

 board/samsung/universal_c210/universal.c |   70 ++++++-----------------------
 1 files changed, 15 insertions(+), 55 deletions(-)

diff --git a/board/samsung/universal_c210/universal.c b/board/samsung/universal_c210/universal.c
index 90fff5c..f6bc51d 100644
--- a/board/samsung/universal_c210/universal.c
+++ b/board/samsung/universal_c210/universal.c
@@ -27,6 +27,7 @@
 #include <asm/arch/adc.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/mmc.h>
+#include <asm/arch/pinmux.h>
 #include <pmic.h>
 #include <usb/s3c_udc.h>
 #include <asm/arch/cpu.h>
@@ -177,7 +178,7 @@ int checkboard(void)
 #ifdef CONFIG_GENERIC_MMC
 int board_mmc_init(bd_t *bis)
 {
-	int i, err;
+	int err;
 
 	switch (get_hwrev()) {
 	case 0:
@@ -199,46 +200,12 @@ int board_mmc_init(bd_t *bis)
 		break;
 	}
 
-	/*
-	 * eMMC GPIO:
-	 * SDR 8-bit at 48MHz at MMC0
-	 * GPK0[0]	SD_0_CLK(2)
-	 * GPK0[1]	SD_0_CMD(2)
-	 * GPK0[2]	SD_0_CDn	-> Not used
-	 * GPK0[3:6]	SD_0_DATA[0:3](2)
-	 * GPK1[3:6]	SD_0_DATA[0:3](3)
-	 *
-	 * DDR 4-bit at 26MHz at MMC4
-	 * GPK0[0]	SD_4_CLK(3)
-	 * GPK0[1]	SD_4_CMD(3)
-	 * GPK0[2]	SD_4_CDn	-> Not used
-	 * GPK0[3:6]	SD_4_DATA[0:3](3)
-	 * GPK1[3:6]	SD_4_DATA[4:7](4)
-	 */
-	for (i = 0; i < 7; i++) {
-		if (i == 2)
-			continue;
-		/* GPK0[0:6] special function 2 */
-		s5p_gpio_cfg_pin(&gpio2->k0, i, 0x2);
-		/* GPK0[0:6] pull disable */
-		s5p_gpio_set_pull(&gpio2->k0, i, GPIO_PULL_NONE);
-		/* GPK0[0:6] drv 4x */
-		s5p_gpio_set_drv(&gpio2->k0, i, GPIO_DRV_4X);
-	}
-
-	for (i = 3; i < 7; i++) {
-		/* GPK1[3:6] special function 3 */
-		s5p_gpio_cfg_pin(&gpio2->k1, i, 0x3);
-		/* GPK1[3:6] pull disable */
-		s5p_gpio_set_pull(&gpio2->k1, i, GPIO_PULL_NONE);
-		/* GPK1[3:6] drv 4x */
-		s5p_gpio_set_drv(&gpio2->k1, i, GPIO_DRV_4X);
+	err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE);
+	if (err) {
+		debug("SDMMC0 not configured\n");
+		return err;
 	}
 
-	/* T-flash detect */
-	s5p_gpio_cfg_pin(&gpio2->x3, 4, 0xf);
-	s5p_gpio_set_pull(&gpio2->x3, 4, GPIO_PULL_UP);
-
 	/*
 	 * MMC device init
 	 * mmc0	 : eMMC (8-bit buswidth)
@@ -246,28 +213,21 @@ int board_mmc_init(bd_t *bis)
 	 */
 	err = s5p_mmc_init(0, 8);
 
+	/* T-flash detect */
+	s5p_gpio_cfg_pin(&gpio2->x3, 4, 0xf);
+	s5p_gpio_set_pull(&gpio2->x3, 4, GPIO_PULL_UP);
+
 	/*
 	 * Check the T-flash  detect pin
 	 * GPX3[4] T-flash detect pin
 	 */
 	if (!s5p_gpio_get_value(&gpio2->x3, 4)) {
-		/*
-		 * SD card GPIO:
-		 * GPK2[0]	SD_2_CLK(2)
-		 * GPK2[1]	SD_2_CMD(2)
-		 * GPK2[2]	SD_2_CDn	-> Not used
-		 * GPK2[3:6]	SD_2_DATA[0:3](2)
-		 */
-		for (i = 0; i < 7; i++) {
-			if (i == 2)
-				continue;
-			/* GPK2[0:6] special function 2 */
-			s5p_gpio_cfg_pin(&gpio2->k2, i, 0x2);
-			/* GPK2[0:6] pull disable */
-			s5p_gpio_set_pull(&gpio2->k2, i, GPIO_PULL_NONE);
-			/* GPK2[0:6] drv 4x */
-			s5p_gpio_set_drv(&gpio2->k2, i, GPIO_DRV_4X);
+		err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
+		if (err) {
+			debug("SDMMC2 not configured\n");
+			return err;
 		}
+
 		err = s5p_mmc_init(2, 4);
 	}
 
-- 
1.7.5.4