[U-Boot] [PATCH v3 4/6] arm:exynos4:trats: Use pinmux for mmc configuration

[Piotr Wilczek]

This patch use the pinmux for mmc configuration for Trats

Signed-off-by: Piotr Wilczek <p.wilczek at samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
CC: Minkyu Kang <mk7.kang at samsung.com>
---
Changes for v2:
- mmc initialisation using pinmux
Changes for v3:
- init SD card also when eMMC init failed

 board/samsung/trats/trats.c |   68 +++++++-----------------------------------
 1 files changed, 12 insertions(+), 56 deletions(-)

diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c
index f5df56c..84b7430 100644
--- a/board/samsung/trats/trats.c
+++ b/board/samsung/trats/trats.c
@@ -29,6 +29,7 @@
 #include <asm/arch/cpu.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/mmc.h>
+#include <asm/arch/pinmux.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/clk.h>
 #include <asm/arch/mipi_dsim.h>
@@ -140,54 +141,22 @@ int board_mmc_init(bd_t *bis)
 {
 	struct exynos4_gpio_part2 *gpio =
 		(struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2();
-	int i, err;
+	int err;
 
 	/* eMMC_EN: SD_0_CDn: GPK0[2] Output High */
 	s5p_gpio_direction_output(&gpio->k0, 2, 1);
 	s5p_gpio_set_pull(&gpio->k0, 2, GPIO_PULL_NONE);
 
 	/*
-	 * eMMC GPIO:
-	 * SDR 8-bit at 48MHz at MMC0
-	 * GPK0[0]	SD_0_CLK(2)
-	 * GPK0[1]	SD_0_CMD(2)
-	 * GPK0[2]	SD_0_CDn	-> Not used
-	 * GPK0[3:6]	SD_0_DATA[0:3](2)
-	 * GPK1[3:6]	SD_0_DATA[0:3](3)
-	 *
-	 * DDR 4-bit at 26MHz at MMC4
-	 * GPK0[0]	SD_4_CLK(3)
-	 * GPK0[1]	SD_4_CMD(3)
-	 * GPK0[2]	SD_4_CDn	-> Not used
-	 * GPK0[3:6]	SD_4_DATA[0:3](3)
-	 * GPK1[3:6]	SD_4_DATA[4:7](4)
-	 */
-	for (i = 0; i < 7; i++) {
-		if (i == 2)
-			continue;
-		/* GPK0[0:6] special function 2 */
-		s5p_gpio_cfg_pin(&gpio->k0, i, 0x2);
-		/* GPK0[0:6] pull disable */
-		s5p_gpio_set_pull(&gpio->k0, i, GPIO_PULL_NONE);
-		/* GPK0[0:6] drv 4x */
-		s5p_gpio_set_drv(&gpio->k0, i, GPIO_DRV_4X);
-	}
-
-	for (i = 3; i < 7; i++) {
-		/* GPK1[3:6] special function 3 */
-		s5p_gpio_cfg_pin(&gpio->k1, i, 0x3);
-		/* GPK1[3:6] pull disable */
-		s5p_gpio_set_pull(&gpio->k1, i, GPIO_PULL_NONE);
-		/* GPK1[3:6] drv 4x */
-		s5p_gpio_set_drv(&gpio->k1, i, GPIO_DRV_4X);
-	}
-
-	/*
 	 * MMC device init
 	 * mmc0	 : eMMC (8-bit buswidth)
 	 * mmc2	 : SD card (4-bit buswidth)
 	 */
-	err = s5p_mmc_init(0, 8);
+	err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE);
+	if (err)
+		debug("SDMMC0 not configured\n");
+	else
+		err = s5p_mmc_init(0, 8);
 
 	/* T-flash detect */
 	s5p_gpio_cfg_pin(&gpio->x3, 4, 0xf);
@@ -198,24 +167,11 @@ int board_mmc_init(bd_t *bis)
 	 * GPX3[4] T-flash detect pin
 	 */
 	if (!s5p_gpio_get_value(&gpio->x3, 4)) {
-		/*
-		 * SD card GPIO:
-		 * GPK2[0]	SD_2_CLK(2)
-		 * GPK2[1]	SD_2_CMD(2)
-		 * GPK2[2]	SD_2_CDn	-> Not used
-		 * GPK2[3:6]	SD_2_DATA[0:3](2)
-		 */
-		for (i = 0; i < 7; i++) {
-			if (i == 2)
-				continue;
-			/* GPK2[0:6] special function 2 */
-			s5p_gpio_cfg_pin(&gpio->k2, i, 0x2);
-			/* GPK2[0:6] pull disable */
-			s5p_gpio_set_pull(&gpio->k2, i, GPIO_PULL_NONE);
-			/* GPK2[0:6] drv 4x */
-			s5p_gpio_set_drv(&gpio->k2, i, GPIO_DRV_4X);
-		}
-		err = s5p_mmc_init(2, 4);
+		err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
+		if (err)
+			debug("SDMMC2 not configured\n");
+		else
+			err = s5p_mmc_init(2, 4);
 	}
 
 	return err;
-- 
1.7.5.4