[U-Boot] [PATCH v2 07/10] NET: mvgbe: add phylib support

Sebastian Hesselbarth sebastian.hesselbarth at gmail.com
Tue Dec 4 09:32:00 CET 2012


This add phylib support to the Marvell GBE driver.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
---
Cc: u-boot at lists.denx.de
Cc: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
Cc: Rabeeh Khoury <rabeeh at solid-run.com>
Cc: Albert Aribaud <albert.u.boot at aribaud.net>
Cc: Prafulla Wadaskar <prafulla at marvell.com>
Cc: Andy Fleming <afleming at gmail.com>
Cc: Joe Hershberger <joe.hershberger at gmail.com>
Cc: Daniel Stodden <daniel.stodden at gmail.com>
Cc: Luka Perkov <luka at openwrt.org>
---
 drivers/net/mvgbe.c |   68 ++++++++++++++++++++++++++++++++++++++++++++++++---
 1 file changed, 64 insertions(+), 4 deletions(-)

diff --git a/drivers/net/mvgbe.c b/drivers/net/mvgbe.c
index 47bf27c..192c989 100644
--- a/drivers/net/mvgbe.c
+++ b/drivers/net/mvgbe.c
@@ -52,7 +52,7 @@ DECLARE_GLOBAL_DATA_PTR;
 #define MV_PHY_ADR_REQUEST 0xee
 #define MVGBE_SMI_REG (((struct mvgbe_registers *)MVGBE0_BASE)->smi)
 
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
+#if defined(CONFIG_PHYLIB) || defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
 /*
  * smi_reg_read - miiphy_read callback function.
  *
@@ -184,6 +184,24 @@ static int smi_reg_write(const char *devname, u8 phy_adr, u8 reg_ofs, u16 data)
 }
 #endif
 
+#if defined(CONFIG_PHYLIB)
+int mvgbe_phy_read(struct mii_dev *bus, int phyAddr, int devAddr, int regAddr)
+{
+	u16 data;
+	int ret;
+	ret = smi_reg_read(bus->name, phyAddr, regAddr, &data);
+	if (ret)
+		return ret;
+	return data;
+}
+
+int mvgbe_phy_write(struct mii_dev *bus, int phyAddr, int devAddr, int regAddr,
+	u16 data)
+{
+	return smi_reg_write(bus->name, phyAddr, regAddr, data);
+}
+#endif
+
 /* Stop and checks all queues */
 static void stop_queue(u32 * qreg)
 {
@@ -467,8 +485,9 @@ static int mvgbe_init(struct eth_device *dev)
 	/* Enable port Rx. */
 	MVGBE_REG_WR(regs->rqc, (1 << RXUQ));
 
-#if (defined (CONFIG_MII) || defined (CONFIG_CMD_MII)) \
-	 && defined (CONFIG_SYS_FAULT_ECHO_LINK_DOWN)
+#if (defined(CONFIG_MII) || defined(CONFIG_CMD_MII))   \
+	&& !defined(CONFIG_PHYLIB)		       \
+	&& defined(CONFIG_SYS_FAULT_ECHO_LINK_DOWN)
 	/* Wait up to 5s for the link status */
 	for (i = 0; i < 5; i++) {
 		u16 phyadr;
@@ -647,6 +666,45 @@ static int mvgbe_recv(struct eth_device *dev)
 	return 0;
 }
 
+#if defined(CONFIG_PHYLIB)
+int mvgbe_phylib_init(struct eth_device *dev, int phyid)
+{
+	struct mii_dev *bus;
+	struct phy_device *phydev;
+	int ret;
+
+	bus = mdio_alloc();
+	if (!bus) {
+		printf("mdio_alloc failed\n");
+		return -ENOMEM;
+	}
+	bus->read = mvgbe_phy_read;
+	bus->write = mvgbe_phy_write;
+	sprintf(bus->name, dev->name);
+
+	ret = mdio_register(bus);
+	if (ret) {
+		printf("mdio_register failed\n");
+		free(bus);
+		return -ENOMEM;
+	}
+
+	/* Set phy address of the port */
+	mvgbe_phy_write(bus, MV_PHY_ADR_REQUEST, 0, MV_PHY_ADR_REQUEST, phyid);
+
+	phydev = phy_connect(bus, phyid, dev, PHY_INTERFACE_MODE_RGMII);
+	if (!phydev) {
+		printf("phy_connect failed\n");
+		return -ENODEV;
+	}
+
+	phy_config(phydev);
+	phy_startup(phydev);
+
+	return 0;
+}
+#endif
+
 int mvgbe_initialize(bd_t *bis)
 {
 	struct mvgbe_device *dmvgbe;
@@ -729,7 +787,9 @@ error1:
 
 		eth_register(dev);
 
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
+#if defined(CONFIG_PHYLIB)
+		mvgbe_phylib_init(dev, PHY_BASE_ADR + devnum);
+#elif defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
 		miiphy_register(dev->name, smi_reg_read, smi_reg_write);
 		/* Set phy address of the port */
 		miiphy_write(dev->name, MV_PHY_ADR_REQUEST,
-- 
1.7.10.4



More information about the U-Boot mailing list