[U-Boot] [PATCH V3 6/9] SMDK5250: Initialise and Enable DWMMC, support FDT and non-FDT
Amar
amarendra.xt at samsung.com
Mon Dec 31 11:58:17 CET 2012
This patch enables and initialises DWMMC for SMDK5250.
Supports both FDT and non-FDT. This patch creates a new file
'exynos5-dt.c' meant for FDT support.
exynos5-dt.c: This file shall contain all code which supports FDT.
Any addition of FDT support for any module needs to be
added in this file.
smdk5250.c: This file shall contain the code which supports non-FDT.
version. Any addition of non-FDT support for any module
needs to be added in this file.
May be, the file smdk5250.c can be removed in near future
when non-FDT is not required.
The Makefile is updated to compile only one of the files
exynos5-dt.c / smdk5250.c based on FDT configuration.
NOTE:
Please note that all additions corresponding to FDT need to be added into the
file exynos5-dt.c.
At same time if non-FDT support is required then add the corresponding
updations into smdk5250.c.
Changes from V1:
1)A new file 'exynos5-dt.c' is created meant for FDT support
2)Makefile is updated to compile only one of the files
exynos5-dt.c / smdk5250.c based on FDT configuration
Changes from V2:
1)Updation of commit message and resubmition of proper patch set.
Signed-off-by: Amar <amarendra.xt at samsung.com>
---
board/samsung/smdk5250/Makefile | 4 +
board/samsung/smdk5250/exynos5-dt.c | 242 ++++++++++++++++++++++++++++++++++++
board/samsung/smdk5250/smdk5250.c | 97 +++++++--------
include/configs/exynos5250-dt.h | 2 +
include/i2c.h | 2 +
5 files changed, 292 insertions(+), 55 deletions(-)
create mode 100644 board/samsung/smdk5250/exynos5-dt.c
diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile
index 47c6a5a..ecca9f3 100644
--- a/board/samsung/smdk5250/Makefile
+++ b/board/samsung/smdk5250/Makefile
@@ -32,8 +32,12 @@ COBJS += tzpc_init.o
COBJS += smdk5250_spl.o
ifndef CONFIG_SPL_BUILD
+ifdef CONFIG_OF_CONTROL
+COBJS += exynos5-dt.o
+else
COBJS += smdk5250.o
endif
+endif
ifdef CONFIG_SPL_BUILD
COBJS += spl_boot.o
diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c
new file mode 100644
index 0000000..da539ca
--- /dev/null
+++ b/board/samsung/smdk5250/exynos5-dt.c
@@ -0,0 +1,242 @@
+/*
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <fdtdec.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <spi.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dwmmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/sromc.h>
+#include <power/pmic.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+#ifdef CONFIG_EXYNOS_SPI
+ spi_init();
+#endif
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE)
+ + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE)
+ + get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE)
+ + get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE)
+ + get_ram_size((long *)PHYS_SDRAM_5, PHYS_SDRAM_7_SIZE)
+ + get_ram_size((long *)PHYS_SDRAM_6, PHYS_SDRAM_7_SIZE)
+ + get_ram_size((long *)PHYS_SDRAM_7, PHYS_SDRAM_7_SIZE)
+ + get_ram_size((long *)PHYS_SDRAM_8, PHYS_SDRAM_8_SIZE);
+ return 0;
+}
+
+#if defined(CONFIG_POWER)
+int power_init_board(void)
+{
+ if (pmic_init(I2C_PMIC))
+ return -1;
+ else
+ return 0;
+}
+#endif
+
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1,
+ PHYS_SDRAM_1_SIZE);
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+ gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2,
+ PHYS_SDRAM_2_SIZE);
+ gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
+ gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3,
+ PHYS_SDRAM_3_SIZE);
+ gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
+ gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4,
+ PHYS_SDRAM_4_SIZE);
+ gd->bd->bi_dram[4].start = PHYS_SDRAM_5;
+ gd->bd->bi_dram[4].size = get_ram_size((long *)PHYS_SDRAM_5,
+ PHYS_SDRAM_5_SIZE);
+ gd->bd->bi_dram[5].start = PHYS_SDRAM_6;
+ gd->bd->bi_dram[5].size = get_ram_size((long *)PHYS_SDRAM_6,
+ PHYS_SDRAM_6_SIZE);
+ gd->bd->bi_dram[6].start = PHYS_SDRAM_7;
+ gd->bd->bi_dram[6].size = get_ram_size((long *)PHYS_SDRAM_7,
+ PHYS_SDRAM_7_SIZE);
+ gd->bd->bi_dram[7].start = PHYS_SDRAM_8;
+ gd->bd->bi_dram[7].size = get_ram_size((long *)PHYS_SDRAM_8,
+ PHYS_SDRAM_8_SIZE);
+}
+
+static int decode_sromc(const void *blob, struct fdt_sromc *config)
+{
+ int err;
+ int node;
+
+ node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
+ if (node < 0) {
+ debug("Could not find SROMC node\n");
+ return node;
+ }
+
+ config->bank = fdtdec_get_int(blob, node, "bank", 0);
+ config->width = fdtdec_get_int(blob, node, "width", 2);
+
+ err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
+ FDT_SROM_TIMING_COUNT);
+ if (err < 0) {
+ debug("Could not decode SROMC configuration\n");
+ return -FDT_ERR_NOTFOUND;
+ }
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_SMC911X
+ u32 smc_bw_conf, smc_bc_conf;
+ struct fdt_sromc config;
+ fdt_addr_t base_addr;
+ int node;
+
+ node = decode_sromc(gd->fdt_blob, &config);
+ if (node < 0) {
+ debug("%s: Could not find sromc configuration\n", __func__);
+ return 0;
+ }
+ node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
+ if (node < 0) {
+ debug("%s: Could not find lan9215 configuration\n", __func__);
+ return 0;
+ }
+
+ /* We now have a node, so any problems from now on are errors */
+ base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
+ if (base_addr == FDT_ADDR_T_NONE) {
+ debug("%s: Could not find lan9215 address\n", __func__);
+ return -1;
+ }
+
+ /* Ethernet needs data bus width of 16 bits */
+ if (config.width != 2) {
+ debug("%s: Unsupported bus width %d\n", __func__,
+ config.width);
+ return -1;
+ }
+ smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
+ | SROMC_BYTE_ENABLE(config.bank);
+
+ smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) |\
+ SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |\
+ SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |\
+ SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |\
+ SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) |\
+ SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |\
+ SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
+
+ /* Select and configure the SROMC bank */
+ exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
+ s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
+ return smc911x_initialize(0, base_addr);
+#endif
+ return 0;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+ printf("\nBoard: SMDK5250\n");
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+ int ret = 0;
+
+ /* dwmmc initializattion for available channels */
+ ret = exynos_dwmmc_init(gd->fdt_blob);
+ if (ret)
+ debug("dwmmc init failed\n");
+
+ return ret;
+}
+#endif
+
+static int board_uart_init(void)
+{
+ int err;
+
+ err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("UART0 not configured\n");
+ return err;
+ }
+
+ err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("UART1 not configured\n");
+ return err;
+ }
+
+ err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("UART2 not configured\n");
+ return err;
+ }
+
+ err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("UART3 not configured\n");
+ return err;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+ int err;
+ err = board_uart_init();
+ if (err) {
+ debug("UART init failed\n");
+ return err;
+ }
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+ board_i2c_init(gd->fdt_blob);
+#endif
+ return err;
+}
+#endif
diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c
index 73c3ec0..e0fec11 100644
--- a/board/samsung/smdk5250/smdk5250.c
+++ b/board/samsung/smdk5250/smdk5250.c
@@ -27,6 +27,7 @@
#include <netdev.h>
#include <spi.h>
#include <asm/arch/cpu.h>
+#include <asm/arch/dwmmc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc.h>
#include <asm/arch/pinmux.h>
@@ -95,59 +96,13 @@ void dram_init_banksize(void)
PHYS_SDRAM_8_SIZE);
}
-#ifdef CONFIG_OF_CONTROL
-static int decode_sromc(const void *blob, struct fdt_sromc *config)
-{
- int err;
- int node;
-
- node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
- if (node < 0) {
- debug("Could not find SROMC node\n");
- return node;
- }
-
- config->bank = fdtdec_get_int(blob, node, "bank", 0);
- config->width = fdtdec_get_int(blob, node, "width", 2);
-
- err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
- FDT_SROM_TIMING_COUNT);
- if (err < 0) {
- debug("Could not decode SROMC configuration\n");
- return -FDT_ERR_NOTFOUND;
- }
-
- return 0;
-}
-#endif
-
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_SMC911X
u32 smc_bw_conf, smc_bc_conf;
struct fdt_sromc config;
fdt_addr_t base_addr;
- int node;
-
-#ifdef CONFIG_OF_CONTROL
- node = decode_sromc(gd->fdt_blob, &config);
- if (node < 0) {
- debug("%s: Could not find sromc configuration\n", __func__);
- return 0;
- }
- node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
- if (node < 0) {
- debug("%s: Could not find lan9215 configuration\n", __func__);
- return 0;
- }
- /* We now have a node, so any problems from now on are errors */
- base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
- if (base_addr == FDT_ADDR_T_NONE) {
- debug("%s: Could not find lan9215 address\n", __func__);
- return -1;
- }
-#else
/* Non-FDT configuration - bank number and timing parameters*/
config.bank = CONFIG_ENV_SROM_BANK;
config.width = 2;
@@ -160,7 +115,6 @@ int board_eth_init(bd_t *bis)
config.timing[FDT_SROM_TACP] = 0x09;
config.timing[FDT_SROM_PMC] = 0x01;
base_addr = CONFIG_SMC911X_BASE;
-#endif
/* Ethernet needs data bus width of 16 bits */
if (config.width != 2) {
@@ -199,16 +153,31 @@ int checkboard(void)
#ifdef CONFIG_GENERIC_MMC
int board_mmc_init(bd_t *bis)
{
- int err;
+ int err = 0, ret = 0;
err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE);
- if (err) {
+ if (err)
debug("SDMMC0 not configured\n");
- return err;
- }
-
- err = s5p_mmc_init(0, 8);
- return err;
+ ret |= err;
+
+ /*EMMC: dwmmc Channel-0 with 8 bit bus width */
+ err = exynos_dwmmc_init(0, 8);
+ if (err)
+ debug("dwmmc Channel-0 init failed\n");
+ ret |= err;
+
+ err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
+ if (err)
+ debug("SDMMC2 not configured\n");
+ ret |= err;
+
+ /*SD: dwmmc Channel-2 with 4 bit bus width */
+ err = exynos_dwmmc_init(2, 4);
+ if (err)
+ debug("dwmmc Channel-2 init failed\n");
+ ret |= err;
+
+ return ret;
}
#endif
@@ -243,6 +212,24 @@ static int board_uart_init(void)
return 0;
}
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+static int board_i2c_init(void)
+{
+ int i, err;
+
+ for (i = 0; i < CONFIG_MAX_I2C_NUM; i++) {
+ err = exynos_pinmux_config((PERIPH_ID_I2C0 + i),
+ PINMUX_FLAG_NONE);
+ if (err) {
+ debug("I2C%d not configured\n", (PERIPH_ID_I2C0 + i));
+ return err;
+ }
+ }
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+ return 0;
+}
+#endif
+
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
@@ -253,7 +240,7 @@ int board_early_init_f(void)
return err;
}
#ifdef CONFIG_SYS_I2C_INIT_BOARD
- board_i2c_init(gd->fdt_blob);
+ board_i2c_init();
#endif
return err;
}
diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
index 59182f4..6ce73dc 100644
--- a/include/configs/exynos5250-dt.h
+++ b/include/configs/exynos5250-dt.h
@@ -84,6 +84,8 @@
#define CONFIG_MMC
#define CONFIG_SDHCI
#define CONFIG_S5P_SDHCI
+#define CONFIG_DWMMC
+#define CONFIG_EXYNOS_DWMMC
#define CONFIG_BOARD_EARLY_INIT_F
diff --git a/include/i2c.h b/include/i2c.h
index c60d075..0944141 100644
--- a/include/i2c.h
+++ b/include/i2c.h
@@ -263,6 +263,7 @@ extern int get_multi_sda_pin(void);
extern int multi_i2c_init(void);
#endif
+#ifdef CONFIG_OF_CONTROL
/**
* Get FDT values for i2c bus.
*
@@ -270,6 +271,7 @@ extern int multi_i2c_init(void);
* @return the number of I2C bus
*/
void board_i2c_init(const void *blob);
+#endif
/**
* Find the I2C bus number by given a FDT I2C node.
--
1.8.0
More information about the U-Boot
mailing list