[U-Boot] [PATCH v3 3/4] EXYNOS: Add SMDK5250 board support

Chander Kashyap chander.kashyap at linaro.org
Wed Jan 11 14:55:20 CET 2012


SMDK5250 board is based on Samsungs EXYNOS5250 SoC.

Signed-off-by: Chander Kashyap <chander.kashyap at linaro.org>
---
Changes for v2:
	- This patch is bifurcated into borad support and SoC support
	- Fixed typo: s/EEYNOS/EXYNOS
	- Squashed patch "SMDK5250: enable device tree support" in this.
Changes for v3:
	- None

 MAINTAINERS                             |    1 +
 board/samsung/smdk5250/Makefile         |   48 +++
 board/samsung/smdk5250/lowlevel_init.S  |  528 +++++++++++++++++++++++++++
 board/samsung/smdk5250/mem_setup.S      |  600 +++++++++++++++++++++++++++++++
 board/samsung/smdk5250/smdk5250.c       |  125 +++++++
 board/samsung/smdk5250/smdk5250_setup.h |  589 ++++++++++++++++++++++++++++++
 boards.cfg                              |    1 +
 include/configs/smdk5250.h              |  185 ++++++++++
 8 files changed, 2077 insertions(+), 0 deletions(-)
 create mode 100644 board/samsung/smdk5250/Makefile
 create mode 100644 board/samsung/smdk5250/lowlevel_init.S
 create mode 100644 board/samsung/smdk5250/mem_setup.S
 create mode 100644 board/samsung/smdk5250/smdk5250.c
 create mode 100644 board/samsung/smdk5250/smdk5250_setup.h
 create mode 100644 include/configs/smdk5250.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 4bf12b5..f62b03e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -705,6 +705,7 @@ Chander Kashyap <k.chander at samsung.com>
 
 	origen			ARM ARMV7 (EXYNOS4210 SoC)
 	SMDKV310		ARM ARMV7 (EXYNOS4210 SoC)
+	SMDK5250		ARM ARMV7 (EXYNOS5250 SoC)
 
 Torsten Koschorrek <koschorrek at synertronixx.de>
 	scb9328		ARM920T (i.MXL)
diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile
new file mode 100644
index 0000000..a26f896
--- /dev/null
+++ b/board/samsung/smdk5250/Makefile
@@ -0,0 +1,48 @@
+#
+# Copyright (C) 2011 Samsung Electronics
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+SOBJS	:= lowlevel_init.o
+SOBJS	+= mem_setup.o
+COBJS	+= smdk5250.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+
+ALL	:=	 $(obj).depend $(LIB)
+
+all:	$(ALL)
+
+$(LIB):	$(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/samsung/smdk5250/lowlevel_init.S b/board/samsung/smdk5250/lowlevel_init.S
new file mode 100644
index 0000000..ecf1d69
--- /dev/null
+++ b/board/samsung/smdk5250/lowlevel_init.S
@@ -0,0 +1,528 @@
+/*
+ * Lowlevel setup for SMDK5250 board based on S5PC520
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/cpu.h>
+#include "smdk5250_setup.h"
+
+/*
+ * Register usages:
+ *
+ * r5 has zero always
+ * r7 has GPIO part1 base 0x11400000
+ */
+_TEXT_BASE:
+	.word	CONFIG_SYS_TEXT_BASE
+
+	.globl lowlevel_init
+lowlevel_init:
+
+	/* use iROM stack in bl2 */
+	ldr	sp, =0x02050000
+
+	push {lr}
+
+	/* r5 has always zero */
+	mov	r5, #0
+	ldr	r7, =EXYNOS5_GPIO_PART1_BASE
+
+	/* check reset status */
+	ldr	r0, =(EXYNOS5_POWER_BASE + INFORM1_OFFSET)
+	ldr	r1, [r0]
+
+	/* AFTR wakeup reset */
+	ldr	r2, =S5P_CHECK_DIDLE
+	cmp	r1, r2
+	beq	exit_wakeup
+
+	/* LPA wakeup reset */
+	ldr	r2, =S5P_CHECK_LPA
+	cmp	r1, r2
+	beq	exit_wakeup
+
+	/* Sleep wakeup reset */
+	ldr	r2, =S5P_CHECK_SLEEP
+	cmp	r1, r2
+	beq	wakeup_reset
+
+	/*
+	 * If U-boot is already running in ram, no need to relocate U-Boot.
+	 * Memory controller must be configured before relocating U-Boot
+	 * in ram.
+	 */
+	ldr	r0, =0x0ffffff		/* r0 <- Mask Bits*/
+	bic	r1, pc, r0		/* pc <- current addr of code */
+					/* r1 <- unmasked bits of pc */
+	ldr	r2, _TEXT_BASE		/* r2 <- original base addr in ram */
+	bic	r2, r2, r0		/* r2 <- unmasked bits of r2*/
+	cmp	r1, r2			/* compare r1, r2 */
+	beq	1f			/* r0 == r1 then skip sdram init */
+
+	/* init system clock */
+	bl system_clock_init
+
+	/* Memory initialize */
+	bl mem_ctrl_asm_init
+
+1:
+	/* for UART */
+	bl uart_asm_init
+	bl tzpc_init
+	pop	{pc}
+
+wakeup_reset:
+	bl system_clock_init
+	bl mem_ctrl_asm_init
+	bl tzpc_init
+
+exit_wakeup:
+	/* Load return address and jump to kernel */
+	ldr	r0, =(EXYNOS5_POWER_BASE + INFORM0_OFFSET)
+
+	/* r1 = physical address of exynos5_cpu_resume function*/
+	ldr	r1, [r0]
+
+	/* Jump to kernel */
+	mov	pc, r1
+	nop
+	nop
+
+/*
+ * system_clock_init: Initialize core clock and bus clock.
+ * void system_clock_init(void)
+ */
+system_clock_init:
+	push	{lr}
+	ldr	r0, =EXYNOS5_CLOCK_BASE
+
+	/*
+	 * MUX_APLL_SEL[0]: FINPLL = 0
+	 * MUX_CPU_SEL[6]: MOUTAPLL = 0
+	 * MUX_HPM_SEL[20]: MOUTAPLL = 0
+	 */
+	ldr	r1, =0x0
+	ldr	r2, =CLK_SRC_CPU_OFFSET
+	str	r1, [r0, r2]
+
+	/* MUX_MPLL_SEL[8]: FINPLL = 0 */
+	ldr	r1, =0x0
+	ldr	r2, =CLK_SRC_CORE1_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * VPLLSRC_SEL[0]: FINPLL = 0
+	 * MUX_{CPLL[8]}|{EPLL[12]}|{VPLL[16]}_SEL: FINPLL = 0
+	 */
+	ldr	r1, =0x0
+	ldr	r2, =CLK_SRC_TOP2_OFFSET
+	str	r1, [r0, r2]
+
+	/* MUX_BPLL_SEL[0]: FINPLL = 0*/
+	ldr	r1, =0x0
+	ldr	r2, =CLK_SRC_CDREX_OFFSET
+	str	r1, [r0, r2]
+
+	/* MUX_ACLK_* Clock Selection */
+	ldr	r1, =CLK_SRC_TOP0_VAL
+	ldr	r2, =CLK_SRC_TOP0_OFFSET
+	str	r1, [r0, r2]
+
+	/* MUX_ACLK_* Clock Selection */
+	ldr	r1, =CLK_SRC_TOP1_VAL
+	ldr	r2, =CLK_SRC_TOP1_OFFSET
+	str	r1, [r0, r2]
+
+
+	/* MUX_ACLK_* Clock Selection */
+	ldr	r1, =CLK_SRC_TOP3_VAL
+	ldr	r2, =CLK_SRC_TOP3_OFFSET
+	str	r1, [r0, r2]
+
+	/* MUX_PWI_SEL[19:16]: SCLKMPLL = 6 */
+	ldr	r1, =CLK_SRC_CORE0_VAL
+	ldr	r2, =CLK_SRC_CORE0_OFFSET
+	str	r1, [r0, r2]
+
+	/* MUX_ATCLK_LEX[0]: ACLK_200 = 0*/
+	ldr	r1, =CLK_SRC_LEX_VAL
+	ldr	r2, =CLK_SRC_LEX_OFFSET
+	str	r1, [r0, r2]
+
+
+	/* UART [0-5]: SCLKMPLL = 6 */
+	ldr	r1, =CLK_SRC_PERIC0_VAL
+	ldr	r2, =CLK_SRC_PERIC0_OFFSET
+	str	r1, [r0, r2]
+
+	/* Set Clock Ratios */
+	ldr	r1, =CLK_DIV_CPU0_VAL
+	ldr	r2, =CLK_DIV_CPU0_OFFSET
+	str	r1, [r0, r2]
+
+	/* Set COPY and HPM Ratio */
+	ldr	r1, =CLK_DIV_CPU1_VAL
+	ldr	r2, =CLK_DIV_CPU1_OFFSET
+	str	r1, [r0, r2]
+
+	/* CORED_RATIO, COREP_RATIO */
+	ldr	r1, =CLK_DIV_CORE0_VAL
+	ldr	r2, =CLK_DIV_CORE0_OFFSET
+	str	r1, [r0, r2]
+
+	/* PWI_RATIO[11:8], DVSEM_RATIO[22:16], DPM_RATIO[24:20] */
+	ldr	r1, =CLK_DIV_CORE1_VAL
+	ldr	r2, =CLK_DIV_CORE1_OFFSET
+	str	r1, [r0, r2]
+
+	/* ACLK_*_RATIO */
+	ldr	r1, =CLK_DIV_TOP0_VAL
+	ldr	r2, =CLK_DIV_TOP0_OFFSET
+	str	r1, [r0, r2]
+
+	/* ACLK_*_RATIO */
+	ldr	r1, =CLK_DIV_TOP1_VAL
+	ldr	r2, =CLK_DIV_TOP1_OFFSET
+	str	r1, [r0, r2]
+
+	/* CDREX Ratio */
+	ldr	r1, =CLK_DIV_CDREX_VAL
+	ldr	r2, =CLK_DIV_CDREX_OFFSET
+	str	r1, [r0, r2]
+
+	/* MCLK_EFPHY_RATIO[3:0] */
+	ldr	r1, =CLK_DIV_CDREX2_VAL
+	ldr	r2, =CLK_DIV_CDREX2_OFFSET
+	str	r1, [r0, r2]
+
+	/* {PCLK[4:6]|ATCLK[10:8]}_RATIO */
+	ldr	r1, =CLK_DIV_LEX_VAL
+	ldr	r2, =CLK_DIV_LEX_OFFSET
+	str	r1, [r0, r2]
+
+	/* PCLK_R0X_RATIO[3:0] */
+	ldr	r1, =CLK_DIV_R0X_VAL
+	ldr	r2, =CLK_DIV_R0X_OFFSET
+	str	r1, [r0, r2]
+
+	/* PCLK_R1X_RATIO[3:0] */
+	ldr	r1, =CLK_DIV_R1X_VAL
+	ldr	r2, =CLK_DIV_R1X_OFFSET
+	str	r1, [r0, r2]
+
+	/* SATA[24]: SCLKMPLL=0, MMC[0-4]: SCLKMPLL = 6 */
+	ldr	r1, =CLK_SRC_FSYS_VAL
+	ldr	r2, =CLK_SRC_FSYS_OFFSET
+	str	r1, [r0, r2]
+
+	/* UART[0-4] */
+	ldr	r1, =CLK_DIV_PERIC0_VAL
+	ldr	r2, =CLK_DIV_PERIC0_OFFSET
+	str	r1, [r0, r2]
+
+	/* PWM_RATIO[3:0] */
+	ldr	r1, =CLK_DIV_PERIC3_VAL
+	ldr	r2, =CLK_DIV_PERIC3_OFFSET
+	str	r1, [r0, r2]
+
+	/* SATA_RATIO, USB_DRD_RATIO */
+	ldr	r1, =CLK_DIV_FSYS0_VAL
+	ldr	r2, =CLK_DIV_FSYS0_OFFSET
+	str	r1, [r0, r2]
+
+	/* MMC[0-1] */
+	ldr	r1, =CLK_DIV_FSYS1_VAL
+	ldr	r2, =CLK_DIV_FSYS1_OFFSET
+	str	r1, [r0, r2]
+
+	/* MMC[2-3] */
+	ldr	r1, =CLK_DIV_FSYS2_VAL
+	ldr	r2, =CLK_DIV_FSYS2_OFFSET
+	str	r1, [r0, r2]
+
+	/* MMC[4] */
+	ldr	r1, =CLK_DIV_FSYS3_VAL
+	ldr	r2, =CLK_DIV_FSYS3_OFFSET
+	str	r1, [r0, r2]
+
+	/* ACLK|PLCK_ACP_RATIO */
+	ldr	r1, =CLK_DIV_ACP_VAL
+	ldr	r2, =CLK_DIV_ACP_OFFSET
+	str	r1, [r0, r2]
+
+	/* ISPDIV0_RATIO, ISPDIV1_RATIO */
+	ldr	r1, =CLK_DIV_ISP0_VAL
+	ldr	r2, =CLK_DIV_ISP0_OFFSET
+	str	r1, [r0, r2]
+
+	/* MCUISPDIV0_RATIO, MCUISPDIV1_RATIO */
+	ldr	r1, =CLK_DIV_ISP1_VAL
+	ldr	r2, =CLK_DIV_ISP1_OFFSET
+	str	r1, [r0, r2]
+
+	/* MPWMDIV_RATIO */
+	ldr	r1, =CLK_DIV_ISP2_VAL
+	ldr	r2, =CLK_DIV_ISP2_OFFSET
+	str	r1, [r0, r2]
+
+	/* PLL locktime */
+	ldr	r1, =APLL_LOCK_VAL
+	ldr	r2, =APLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	ldr	r1, =MPLL_LOCK_VAL
+	ldr	r2, =MPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	ldr	r1, =BPLL_LOCK_VAL
+	ldr	r2, =BPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	ldr	r1, =CPLL_LOCK_VAL
+	ldr	r2, =CPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	ldr	r1, =EPLL_LOCK_VAL
+	ldr	r2, =EPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	ldr	r1, =VPLL_LOCK_VAL
+	ldr	r2, =VPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	mov	r1, #0x10000
+2:	subs	r1, r1, #1
+	bne	2b
+
+
+	/* Set APLL */
+	ldr	r1, =APLL_CON1_VAL
+	ldr	r2, =APLL_CON1_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =APLL_CON0_VAL
+	ldr	r2, =APLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	mov	r1, #0x30000
+3:	subs	r1, r1, #1
+	bne	3b
+
+	/* Set MPLL */
+	ldr	r1, =MPLL_CON1_VAL
+	ldr	r2, =MPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =MPLL_CON0_VAL
+	ldr	r2, =MPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x30000
+4:	subs	r1, r1, #1
+	bne	4b
+
+	/* Set BPLL */
+	ldr	r1, =BPLL_CON1_VAL
+	ldr	r2, =BPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =BPLL_CON0_VAL
+	ldr	r2, =BPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x30000
+5:	subs	r1, r1, #1
+	bne	5b
+
+	/* Set CPLL */
+	ldr	r1, =CPLL_CON1_VAL
+	ldr	r2, =CPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =CPLL_CON0_VAL
+	ldr	r2, =CPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x30000
+6:	subs	r1, r1, #1
+	bne	6b
+
+	/* Set EPLL */
+	ldr	r1, =EPLL_CON2_VAL
+	ldr	r2, =EPLL_CON2_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =EPLL_CON1_VAL
+	ldr	r2, =EPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =EPLL_CON0_VAL
+	ldr	r2, =EPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x30000
+7:	subs	r1, r1, #1
+	bne	7b
+
+	/* Set VPLL */
+	ldr	r1, =VPLL_CON2_VAL
+	ldr	r2, =VPLL_CON2_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =VPLL_CON1_VAL
+	ldr	r2, =VPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =VPLL_CON0_VAL
+	ldr	r2, =VPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x30000
+8:	subs	r1, r1, #1
+	bne	8b
+
+	/* After Initiallising th PLL select the sources accordingly */
+	/* MUX_APLL_SEL[0]: MOUTAPLLFOUT = 1 */
+	ldr	r1, =CLK_SRC_CPU_VAL
+	ldr	r2, =CLK_SRC_CPU_OFFSET
+	str	r1, [r0, r2]
+
+	/* MUX_MPLL_SEL[8]: MOUTMPLLFOUT = 1 */
+	ldr	r1, =CLK_SRC_CORE1_VAL
+	ldr	r2, =CLK_SRC_CORE1_OFFSET
+	str	r1, [r0, r2]
+
+	/* MUX_BPLL_SEL[0]: FOUTBPLL = 1*/
+	ldr	r1, =CLK_SRC_CDREX_VAL
+	ldr	r2, =CLK_SRC_CDREX_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * VPLLSRC_SEL[0]: FINPLL = 0
+	 * MUX_{CPLL[8]}|{EPLL[12]}|{VPLL[16]}_SEL: MOUT{CPLL|EPLL|VPLL} = 1
+	 * MUX_{MPLL[20]}|{BPLL[24]}_USER_SEL: FOUT{MPLL|BPLL} = 1
+	 */
+	ldr	r1, =CLK_SRC_TOP2_VAL
+	ldr	r2, =CLK_SRC_TOP2_OFFSET
+	str	r1, [r0, r2]
+
+	pop	{pc}
+
+
+/*
+ * uart_asm_init: Initialize UART in asm mode, 115200bps fixed.
+ * void uart_asm_init(void)
+ */
+	.globl uart_asm_init
+uart_asm_init:
+
+	/* setup UART0-UART3 GPIOs (part1) */
+	mov	r0, r7
+	ldr	r1, =EXYNOS5_GPIO_A0_CON_VAL
+	str	r1, [r0, #EXYNOS5_GPIO_A0_CON_OFFSET]
+	ldr	r1, =EXYNOS5_GPIO_A1_CON_VAL
+	str	r1, [r0, #EXYNOS5_GPIO_A1_CON_OFFSET]
+
+	ldr r0, =EXYNOS5_UART_BASE
+	add r0, r0, #EXYNOS5_DEFAULT_UART_OFFSET
+
+	ldr	r1, =ULCON_VAL
+	str	r1, [r0, #ULCON_OFFSET]
+	ldr	r1, =UCON_VAL
+	str	r1, [r0, #UCON_OFFSET]
+	ldr	r1, =UFCON_VAL
+	str	r1, [r0, #UFCON_OFFSET]
+	ldr	r1, =UBRDIV_VAL
+	str	r1, [r0, #UBRDIV_OFFSET]
+	ldr	r1, =UFRACVAL_VAL
+	str	r1, [r0, #UFRACVAL_OFFSET]
+	ldr	r1, =0x4f
+	str	r1, [r0, #UTXH_OFFSET]		@'O'
+	mov	pc, lr
+	nop
+	nop
+	nop
+
+/* Setting TZPC[TrustZone Protection Controller] */
+tzpc_init:
+
+	ldr	r0, =TZPC0_BASE
+	mov	r1, #R0SIZE
+	str	r1, [r0]
+	mov	r1, #DECPROTXSET
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC1_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC2_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC3_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC4_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC5_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC6_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC7_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC8_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC9_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+
+	mov	pc, lr
diff --git a/board/samsung/smdk5250/mem_setup.S b/board/samsung/smdk5250/mem_setup.S
new file mode 100644
index 0000000..a7cc54b
--- /dev/null
+++ b/board/samsung/smdk5250/mem_setup.S
@@ -0,0 +1,600 @@
+/*
+ * Memory setup for SMDK5250 board based on EXYNOS5
+ *
+ * (C) Copyright 2011 Samsung Electronics Co. Ltd
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <config.h>
+#include "smdk5250_setup.h"
+/* APLL : 1GHz */
+/* MCLK_CDREX: MCLK_CDREX_533*/
+/* LPDDR support: LPDDR2 */
+
+/* (Memory Interleaving Size = 1 << IV_SIZE) */
+#define CONFIG_IV_SIZE 0x07
+#define RD_LVL		1
+
+	.globl mem_ctrl_asm_init
+mem_ctrl_asm_init:
+	push	{lr}
+
+	/* CLK_DIV_DMC0 on iROM DMC=50MHz for Init DMC */
+	ldr	r0, =EXYNOS5_CLOCK_BASE
+
+	/* Reset PHY Controllor */
+	ldr	r1, =0x0
+	ldr	r2, =LPDDR3PHY_CTRL
+	str	r1, [r0, r2]
+
+	bl	delay
+
+	/*set Read Latance and Burst Length for PHY0 and PHY1 */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x408
+	str	r1, [r0, #DMC_PHY_CON42]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x408
+	str	r1, [r0, #DMC_PHY_CON42]
+
+	/*
+	 * ZQ Calibration:
+	 * Select Driver Strength,
+	 * long calibration for manual calibration
+	 */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x0DA40304
+	str	r1, [r0, #DMC_PHY_CON16]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x0DA40304
+	str	r1, [r0, #DMC_PHY_CON16]
+
+	/* Enable termination */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x0DAC0304
+	str	r1, [r0, #DMC_PHY_CON16]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x0DAC0304
+	str	r1, [r0, #DMC_PHY_CON16]
+
+	/* Start Manual Calibration */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x0DAC0306
+	str	r1, [r0, #DMC_PHY_CON16]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x0DAC0306
+	str	r1, [r0, #DMC_PHY_CON16]
+
+	bl	delay
+
+	/* Enable termination */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x0DAC0304
+	str	r1, [r0, #DMC_PHY_CON16]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x0DAC0304
+	str	r1, [r0, #DMC_PHY_CON16]
+
+	/* DDR Mode: LPDDR2 */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x17021240
+	str	r1, [r0, #DMC_PHY_CON0]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x17021240
+	str	r1, [r0, #DMC_PHY_CON0]
+
+	/* DQS, DQ: Signal, for LPDDR2: Always Set */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x00000F0F
+	str	r1, [r0, #DMC_PHY_CON14]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x00000F0F
+	str	r1, [r0, #DMC_PHY_CON14]
+
+	/* RD_FETCH: 1 */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x1FFF1000
+	str	r1, [r0, #DMC_CONCONTROL]
+	bl	delay
+
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x0FFF1000
+	str	r1, [r0, #DMC_CONCONTROL]
+
+	bl	delay
+	/*
+	 * Update DLL Information:
+	 * Force DLL Resyncronization
+	 */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000008
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/* Reset Force DLL Resyncronization */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000000
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/*
+	 * Dynamic Clock: Always Running
+	 * Memory Burst length: 4
+	 * Number of chips: 2
+	 * Memory Bus width: 32 bit
+	 * Memory Type: LPDDR2-S4
+	 * Additional Latancy for PLL: 1 Cycle
+	 */
+	ldr	r1, =0x00212500
+	str	r1, [r0, #DMC_MEMCONTROL]
+
+	/*
+	 * Memory Configuration Chip 0
+	 * Address Mapping: Interleaved
+	 * Number of Column address Bits: 10 bits
+	 * Number of Rows Address Bits: 14
+	 * Number of Banks: 8
+	 */
+	ldr	r1, =0x00001323
+	str	r1, [r0, #DMC_MEMCONFIG0]
+
+	/*
+	 * Memory Configuration Chip 1
+	 * Address Mapping: Interleaved
+	 * Number of Column address Bits: 10 bits
+	 * Number of Rows Address Bits: 14
+	 * Number of Banks: 8
+	 */
+	ldr	r1, =0x00001323
+	str	r1, [r0, #DMC_MEMCONFIG1]
+
+	/*
+	 * Chip0: AXI
+	 * AXI Base Address: 0x40000000
+	 * AXI Base Address Mask: 0x780
+	 */
+	ldr	r1, =0x00400780
+	str	r1, [r0, #DMC_MEMBASECONFIG0]
+
+	/*
+	 * Chip1: AXI
+	 * AXI Base Address: 0x80000000
+	 * AXI Base Address Mask: 0x780
+	 */
+	ldr	r1, =0x00800780
+	str	r1, [r0, #DMC_MEMBASECONFIG1]
+
+	/* Precharge Configuration */
+	ldr	r1, =0xFF000000
+	str	r1, [r0, #DMC_PRECHCONFIG]
+
+	/* Power Down mode Configuration */
+	ldr	r1, =0xFFFF00FF
+	str	r1, [r0, #DMC_PWRDNCONFIG]
+
+	/* Periodic Refrese Interval */
+	ldr	r1, =0x0000005D
+	str	r1, [r0, #DMC_TIMINGAREF]
+
+	/* MCLK_CDREX_533 */
+	/*
+	 * TimingRow, TimingData, TimingPower Setting:
+	 * Values as per Memory AC Parameters
+	 */
+	ldr	r1, =0x2336544C
+	str	r1, [r0, #DMC_TIMINGROW]
+
+	ldr	r1, =0x24202408
+	str	r1, [r0, #DMC_TIMINGDATA]
+
+	ldr	r1, =0x38260235
+	str	r1, [r0, #DMC_TIMINGPOWER]
+
+	/* Memory Channel Inteleaving Size: 128 Bytes */
+	ldr	r1, =CONFIG_IV_SIZE
+	str	r1, [r0, #DMC_IVCONTROL]
+
+	/* Set Offsets to read DQS */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x7F7F7F7F
+	str	r1, [r0, #DMC_PHY_CON4]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x7F7F7F7F
+	str	r1, [r0, #DMC_PHY_CON4]
+
+	/* Set Offsets to read DQ */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x7F7F7F7F
+	str	r1, [r0, #DMC_PHY_CON6]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x7F7F7F7F
+	str	r1, [r0, #DMC_PHY_CON6]
+
+	/* Debug Offset */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x0000007F
+	str	r1, [r0, #DMC_PHY_CON10]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x0000007F
+	str	r1, [r0, #DMC_PHY_CON10]
+
+	/* Start DLL Locking */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x10107F50
+	str	r1, [r0, #DMC_PHY_CON12]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x10107F50
+	str	r1, [r0, #DMC_PHY_CON12]
+
+	bl	delay
+
+	/*
+	 * Update DLL Information:
+	 * Force DLL Resyncronization
+	 */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000008
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/* Reset DLL Resyncronization */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000000
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/*
+	 * NOP CMD: Channel 0, Chip 0
+	 * Exit from active/precharge power down or deep power down
+	 */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x07000000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+	ldr	r1, =0x00071C00
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	ldr	r1, =0x00010BFC
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* MCLK_CDREX_533 */
+	ldr	r1, =0x00000708
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	ldr	r1, =0x00000818
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/*
+	 * NOP CMD: Channel 0, Chip 1
+	 * Exit from active/precharge power down or deep power down
+	 */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x07100000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+	ldr	r1, =0x00171C00
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	ldr	r1, =0x00110BFC
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* MCLK_CDREX_533 */
+	ldr	r1, =0x00100708
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	ldr	r1, =0x00100818
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/*
+	 * NOP CMD: Channel 1, Chip 0
+	 * Exit from active/precharge power down or deep power down
+	 */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x17000000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+	ldr	r1, =0x10071C00
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	ldr	r1, =0x10010BFC
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* MCLK_CDREX_533 */
+	ldr	r1, =0x10000708
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	ldr	r1, =0x10000818
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/*
+	 * NOP CMD: Channel 1, Chip 1
+	 * Exit from active/precharge power down or deep power down
+	 */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x17100000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+	ldr	r1, =0x10171C00
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	ldr	r1, =0x10110BFC
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* MCLK_CDREX_533 */
+	ldr	r1, =0x10100708
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	ldr	r1, =0x10100818
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* Reset DQS Offsets */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x08080808
+	str	r1, [r0, #DMC_PHY_CON4]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x08080808
+	str	r1, [r0, #DMC_PHY_CON4]
+
+	/* Reset DQ Offsets */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x08080808
+	str	r1, [r0, #DMC_PHY_CON6]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x08080808
+	str	r1, [r0, #DMC_PHY_CON6]
+
+	/* Reset debug Offsets */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x00000008
+	str	r1, [r0, #DMC_PHY_CON10]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x00000008
+	str	r1, [r0, #DMC_PHY_CON10]
+
+	/* Set DLL Locking */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x10107F30
+	str	r1, [r0, #DMC_PHY_CON12]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x10107F30
+	str	r1, [r0, #DMC_PHY_CON12]
+
+	bl	delay
+
+	/* Start DLL Locking */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x10107F70
+	str	r1, [r0, #DMC_PHY_CON12]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x10107F70
+	str	r1, [r0, #DMC_PHY_CON12]
+
+	bl	delay
+
+	/*
+	 * Update DLL Information:
+	 * Force DLL Resyncronization
+	 */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000008
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/* Reset DLL Resyncronization */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000000
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	bl	delay
+
+	/*
+	 * Update DLL Information:
+	 * Force DLL Resyncronization
+	 */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000008
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/* Reset DLL Resyncronization */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000000
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	bl	delay
+#if defined(RD_LVL)
+	/* DLL On */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x10102D50
+	str	r1, [r0, #DMC_PHY_CON12]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x10102D50
+	str	r1, [r0, #DMC_PHY_CON12]
+
+	/*
+	 * Set ctrl_gateadj, ctrl_readadj
+	 * ctrl_gateduradj, rdlvl_pass_adj
+	 * rdlvl_rddataPadj
+	 */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x09210001
+	str	r1, [r0, #DMC_PHY_CON1]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x09210001
+	str	r1, [r0, #DMC_PHY_CON1]
+
+	/* LPDDR2 Address */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x00000208
+	str	r1, [r0, #DMC_PHY_CON22]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x00000208
+	str	r1, [r0, #DMC_PHY_CON22]
+
+	/* Enable Byte Read Leleling */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x17023240
+	str	r1, [r0, #DMC_PHY_CON0]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x17023240
+	str	r1, [r0, #DMC_PHY_CON0]
+
+	/* rdlvl_en: Use levelling offset instead ctrl_shiftc */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x02010004
+	str	r1, [r0, #DMC_PHY_CON2]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x02010004
+	str	r1, [r0, #DMC_PHY_CON2]
+
+	bl	delay
+
+	/* Enable Data Eye Trainig */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000002
+	str	r1, [r0, #DMC_RDLVL_CONFIG]
+
+	bl	delay
+
+	/* Disable Data Eye Trainig */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000000
+	str	r1, [r0, #DMC_RDLVL_CONFIG]
+
+	/* RdDeSkew_clear: Clear */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x02012004
+	str	r1, [r0, #DMC_PHY_CON2]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x02012004
+	str	r1, [r0, #DMC_PHY_CON2]
+
+	/* Start DLL Locking */
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x10107F70
+	str	r1, [r0, #DMC_PHY_CON12]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x10107F70
+	str	r1, [r0, #DMC_PHY_CON12]
+
+	/* Force DLL Resyncronization */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000008
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/* Reset DLL Resyncronization */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00000000
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	bl	delay
+
+	/* ctrl_atgate: ctrl_gate_p*, ctrl_read_p* generated by PHY*/
+	ldr	r0, =EXYNOS5_PHY0_CTRL_BASE
+	ldr	r1, =0x17023200
+	str	r1, [r0, #DMC_PHY_CON0]
+	ldr	r0, =EXYNOS5_PHY1_CTRL_BASE
+	ldr	r1, =0x17023200
+	str	r1, [r0, #DMC_PHY_CON0]
+
+	/* Channel:0, Chip:0, PALL (all banks precharge) CMD */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x01000000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* Channel:0, Chip:1, PALL (all banks precharge) CMD */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x01100000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* Channel:1, Chip:0, PALL (all banks precharge) CMD */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x11000000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+
+	/* Channel:1, Chip:1, PALL (all banks precharge) CMD */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x11100000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	bl	delay
+#endif
+	/*
+	 * Dynamic Clock: Stops During Idle Period
+	 * Dynamic Power Down: Enable
+	 * Dynamic Self refresh: Enable
+	 * Memory Burst length: 4
+	 * Number of chips: 2
+	 * Memory Bus width: 32 bit
+	 * Memory Type: LPDDR2-S4
+	 * Additional Latancy for PLL: 1 Cycle
+	 */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x00212523
+	str	r1, [r0, #DMC_MEMCONTROL]
+
+	/* Start Auto refresh */
+	ldr	r0, =EXYNOS5_DMC_CTRL_BASE
+	ldr	r1, =0x0FFF10E0
+	str	r1, [r0, #DMC_CONCONTROL]
+
+	pop	{lr}
+	mov	pc, lr
+
+delay:
+	mov	r2, #0x10000
+delayloop:
+	subs	r2, r2, #1
+	bne	delayloop
+	mov	pc, lr
diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c
new file mode 100644
index 0000000..0ea9a32
--- /dev/null
+++ b/board/samsung/smdk5250/smdk5250.c
@@ -0,0 +1,125 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <netdev.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/sromc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+struct exynos5_gpio_part1 *gpio1;
+
+int board_init(void)
+{
+	gpio1 = (struct exynos5_gpio_part1 *) EXYNOS5_GPIO_PART1_BASE;
+
+	gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size	= get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_5, PHYS_SDRAM_7_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_6, PHYS_SDRAM_7_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_7, PHYS_SDRAM_7_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_8, PHYS_SDRAM_8_SIZE);
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, \
+							PHYS_SDRAM_1_SIZE);
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, \
+							PHYS_SDRAM_2_SIZE);
+	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
+	gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3, \
+							PHYS_SDRAM_3_SIZE);
+	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
+	gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4, \
+							PHYS_SDRAM_4_SIZE);
+	gd->bd->bi_dram[4].start = PHYS_SDRAM_5;
+	gd->bd->bi_dram[4].size = get_ram_size((long *)PHYS_SDRAM_5, \
+							PHYS_SDRAM_5_SIZE);
+	gd->bd->bi_dram[5].start = PHYS_SDRAM_6;
+	gd->bd->bi_dram[5].size = get_ram_size((long *)PHYS_SDRAM_6, \
+							PHYS_SDRAM_6_SIZE);
+	gd->bd->bi_dram[6].start = PHYS_SDRAM_7;
+	gd->bd->bi_dram[6].size = get_ram_size((long *)PHYS_SDRAM_7, \
+							PHYS_SDRAM_7_SIZE);
+	gd->bd->bi_dram[7].start = PHYS_SDRAM_8;
+	gd->bd->bi_dram[7].size = get_ram_size((long *)PHYS_SDRAM_8, \
+							PHYS_SDRAM_8_SIZE);
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+	printf("\nBoard: SMDK5250\n");
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+	int i, err;
+
+	/*
+	 * MMC2 SD card GPIO:
+	 *
+	 * GPC2[0]	SD_2_CLK(2)
+	 * GPC2[1]	SD_2_CMD(2)
+	 * GPC2[2]	SD_2_CDn
+	 * GPC2[3:6]	SD_2_DATA[0:3](2)
+	 */
+	for (i = 0; i < 7; i++) {
+		/* GPC2[0:6] special function 2 */
+		s5p_gpio_cfg_pin(&gpio1->c2, i, GPIO_FUNC(0x2));
+
+		/* GPK2[0:6] drv 4x */
+		s5p_gpio_set_drv(&gpio1->c2, i, GPIO_DRV_4X);
+
+		/* GPK2[0:1] pull disable */
+		if (i == 0 || i == 1) {
+			s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_NONE);
+			continue;
+		}
+
+		/* GPK2[2:6] pull up */
+		s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_UP);
+	}
+
+	err = s5p_mmc_init(2, 4);
+	return err;
+}
+#endif
diff --git a/board/samsung/smdk5250/smdk5250_setup.h b/board/samsung/smdk5250/smdk5250_setup.h
new file mode 100644
index 0000000..9d0ce0d
--- /dev/null
+++ b/board/samsung/smdk5250/smdk5250_setup.h
@@ -0,0 +1,589 @@
+/*
+ * Machine Specific Values for SMDK5250 board based on S5PC520
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _SMDK5250_SETUP_H
+#define _SMDK5250_SETUP_H
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/cpu.h>
+
+/* Offsets of clock registers (sources and dividers) */
+#define CLK_SRC_CPU_OFFSET	0x00200
+#define CLK_DIV_CPU0_OFFSET	0x00500
+#define CLK_DIV_CPU1_OFFSET	0x00504
+
+#define CLK_SRC_CORE0_OFFSET	0x04200
+#define CLK_DIV_CORE0_OFFSET	0x04500
+
+#define CLK_SRC_CORE1_OFFSET	0x04204
+#define CLK_DIV_CORE1_OFFSET	0x04504
+
+#define CLK_SRC_TOP0_OFFSET	0x10210
+#define CLK_SRC_TOP1_OFFSET	0x10214
+#define CLK_SRC_TOP2_OFFSET	0x10218
+#define CLK_SRC_TOP3_OFFSET	0x1021C
+#define CLK_DIV_TOP0_OFFSET	0x10510
+#define CLK_DIV_TOP1_OFFSET	0x10514
+
+#define CLK_SRC_FSYS_OFFSET	0x10244
+#define CLK_DIV_FSYS0_OFFSET	0x10548
+#define CLK_DIV_FSYS1_OFFSET	0x1054C
+#define CLK_DIV_FSYS2_OFFSET	0x10550
+#define CLK_DIV_FSYS3_OFFSET	0x10554
+
+#define CLK_SRC_PERIC0_OFFSET	0x10250
+#define CLK_DIV_PERIC0_OFFSET	0x10558
+#define CLK_DIV_PERIC3_OFFSET	0x10564
+
+#define CLK_SRC_LEX_OFFSET	0x14200
+#define CLK_DIV_LEX_OFFSET	0x14500
+
+#define CLK_DIV_R0X_OFFSET	0x18500
+#define CLK_DIV_R1X_OFFSET	0x1C500
+
+
+#define CLK_SRC_CDREX_OFFSET	0x20200
+#define CLK_DIV_CDREX_OFFSET	0x20500
+#define CLK_DIV_CDREX2_OFFSET	0x20504
+
+#define CLK_DIV_ACP_OFFSET	0x08500
+#define CLK_DIV_ISP0_OFFSET	0x0C300
+#define CLK_DIV_ISP1_OFFSET	0x0C304
+#define CLK_DIV_ISP2_OFFSET	0x0C308
+
+
+#define APLL_LOCK_OFFSET	0x00000
+#define MPLL_LOCK_OFFSET	0x04000
+#define APLL_CON0_OFFSET	0x00100
+#define APLL_CON1_OFFSET	0x00104
+#define MPLL_CON0_OFFSET	0x04100
+#define MPLL_CON1_OFFSET	0x04104
+
+#define BPLL_LOCK_OFFSET	0x20010
+#define BPLL_CON0_OFFSET	0x20110
+#define BPLL_CON1_OFFSET	0x20114
+
+#define CPLL_LOCK_OFFSET	0x10020
+#define EPLL_LOCK_OFFSET	0x10030
+#define VPLL_LOCK_OFFSET	0x10040
+
+#define CPLL_CON0_OFFSET	0x10120
+#define CPLL_CON1_OFFSET	0x10124
+
+#define EPLL_CON0_OFFSET	0x10130
+#define EPLL_CON1_OFFSET	0x10134
+#define EPLL_CON2_OFFSET	0x10138
+
+#define VPLL_CON0_OFFSET	0x10140
+#define VPLL_CON1_OFFSET	0x10144
+#define VPLL_CON2_OFFSET	0x10148
+
+
+/* DMC: DRAM Controllor Register offsets */
+#define DMC_CONCONTROL		0x00
+#define DMC_MEMCONTROL		0x04
+#define DMC_MEMCONFIG0		0x08
+#define DMC_MEMCONFIG1		0x0C
+#define DMC_DIRECTCMD		0x10
+#define DMC_PRECHCONFIG		0x14
+#define DMC_PHYCONTROL0		0x18
+#define DMC_PWRDNCONFIG		0x28
+#define DMC_TIMINGAREF		0x30
+#define DMC_TIMINGROW		0x34
+#define DMC_TIMINGDATA		0x38
+#define DMC_TIMINGPOWER		0x3C
+#define DMC_IVCONTROL		0xF0
+#define DMC_RDLVL_CONFIG	0xF8
+#define DMC_MEMBASECONFIG0	0x010C
+#define DMC_MEMBASECONFIG1	0x0110
+#define LPDDR3PHY_CTRL		0x20A10
+
+#define DMC_PHY_CON0		0x00
+#define DMC_PHY_CON1		0x04
+#define DMC_PHY_CON10		0x28
+#define DMC_PHY_CON12		0x30
+#define DMC_PHY_CON14		0x38
+#define DMC_PHY_CON16		0x40
+#define DMC_PHY_CON2		0x08
+#define DMC_PHY_CON22		0x5C
+#define DMC_PHY_CON4		0x10
+#define DMC_PHY_CON42		0xAC
+#define DMC_PHY_CON6		0x18
+
+/* Offset for inform registers */
+#define INFORM0_OFFSET		0x800
+#define INFORM1_OFFSET		0x804
+
+/* GPIO Offsets for UART: GPIO Contol Register */
+#define EXYNOS5_GPIO_A0_CON_OFFSET	0x0
+#define EXYNOS5_GPIO_A1_CON_OFFSET	0x20
+
+/* UART Register offsets */
+#define ULCON_OFFSET		0x00
+#define UCON_OFFSET		0x04
+#define UFCON_OFFSET		0x08
+#define UBRDIV_OFFSET		0x28
+#define UFRACVAL_OFFSET		0x2C
+#define UTXH_OFFSET		0x20
+
+/* TZPC : Register Offsets */
+#define TZPC0_BASE		0x10100000
+#define TZPC1_BASE		0x10110000
+#define TZPC2_BASE		0x10120000
+#define TZPC3_BASE		0x10130000
+#define TZPC4_BASE		0x10140000
+#define TZPC5_BASE		0x10150000
+#define TZPC6_BASE		0x10160000
+#define TZPC7_BASE		0x10170000
+#define TZPC8_BASE		0x10180000
+#define TZPC9_BASE		0x10190000
+
+#define TZPC_DECPROT0SET_OFFSET	0x804
+#define TZPC_DECPROT1SET_OFFSET	0x810
+#define TZPC_DECPROT2SET_OFFSET	0x81C
+#define TZPC_DECPROT3SET_OFFSET	0x828
+
+/* CLK_SRC_CPU */
+/* 0 = MOUTAPLL, 1 = SCLKMPLL	*/
+#define MUX_HPM_SEL		0
+#define MUX_CPU_SEL		0
+#define MUX_APLL_SEL		1
+#define CLK_SRC_CPU_VAL		((MUX_HPM_SEL << 20) \
+				| (MUX_CPU_SEL << 16) \
+				| (MUX_APLL_SEL))
+
+/* CLK_DIV_CPU0	*/
+#define ARM2_RATIO		0x0
+#define APLL_RATIO		0x1
+#define PCLK_DBG_RATIO		0x1
+#define ATB_RATIO		0x4
+#define PERIPH_RATIO		0x7
+#define ACP_RATIO		0x7
+#define CPUD_RATIO		0x2
+#define ARM_RATIO		0x0
+#define CLK_DIV_CPU0_VAL	((ARM2_RATIO << 28) \
+				| (APLL_RATIO << 24) \
+				| (PCLK_DBG_RATIO << 20) \
+				| (ATB_RATIO << 16) \
+				| (PERIPH_RATIO << 12) \
+				| (ACP_RATIO << 8) \
+				| (CPUD_RATIO << 4) \
+				| (ARM_RATIO))
+
+/* CLK_DIV_CPU1	*/
+#define HPM_RATIO		0x4
+#define COPY_RATIO		0x0
+#define CLK_DIV_CPU1_VAL	((HPM_RATIO << 4) \
+				| (COPY_RATIO))
+
+#define APLL_MDIV		0x7D
+#define APLL_PDIV		0x3
+#define APLL_SDIV		0x0
+
+#define MPLL_MDIV		0x64
+#define MPLL_PDIV		0x3
+#define MPLL_SDIV		0x0
+
+#define CPLL_MDIV		0x96
+#define CPLL_PDIV		0x4
+#define CPLL_SDIV		0x0
+
+/* APLL_CON1	*/
+#define APLL_CON1_VAL	(0x00203800)
+
+/* MPLL_CON1	*/
+#define MPLL_CON1_VAL	(0x00203800)
+
+/* CPLL_CON1	*/
+#define CPLL_CON1_VAL	(0x00203800)
+
+#define EPLL_MDIV	0x60
+#define EPLL_PDIV	0x3
+#define EPLL_SDIV	0x3
+
+#define EPLL_CON1_VAL	0x00000000
+#define EPLL_CON2_VAL	0x00000080
+
+#define VPLL_MDIV	0x96
+#define VPLL_PDIV	0x3
+#define VPLL_SDIV	0x2
+
+#define VPLL_CON1_VAL	0x00000000
+#define VPLL_CON2_VAL	0x00000080
+
+#define BPLL_MDIV	0x215
+#define BPLL_PDIV	0xC
+#define BPLL_SDIV	0x1
+
+#define BPLL_CON1_VAL	0x00203800
+
+/* Set PLL */
+#define set_pll(mdiv, pdiv, sdiv)	(1<<31 | mdiv<<16 | pdiv<<8 | sdiv)
+
+#define APLL_CON0_VAL	set_pll(APLL_MDIV, APLL_PDIV, APLL_SDIV)
+#define MPLL_CON0_VAL	set_pll(MPLL_MDIV, MPLL_PDIV, MPLL_SDIV)
+#define CPLL_CON0_VAL	set_pll(CPLL_MDIV, CPLL_PDIV, CPLL_SDIV)
+#define EPLL_CON0_VAL	set_pll(EPLL_MDIV, EPLL_PDIV, EPLL_SDIV)
+#define VPLL_CON0_VAL	set_pll(VPLL_MDIV, VPLL_PDIV, VPLL_SDIV)
+#define BPLL_CON0_VAL	set_pll(BPLL_MDIV, BPLL_PDIV, BPLL_SDIV)
+
+/* CLK_SRC_CORE0 */
+#define CLK_SRC_CORE0_VAL	0x00060000
+
+/* CLK_SRC_CORE1 */
+#define CLK_SRC_CORE1_VAL	0x100
+
+/* CLK_DIV_CORE0 */
+#define CLK_DIV_CORE0_VAL	0x120000
+
+/* CLK_DIV_CORE1 */
+#define CLK_DIV_CORE1_VAL	0x07070700
+
+/* CLK_SRC_CDREX */
+#define CLK_SRC_CDREX_VAL	0x111
+
+/* CLK_DIV_CDREX */
+#define MCLK_CDREX2_RATIO	0x0
+#define ACLK_EFCON_RATIO	0x1
+#define MCLK_DPHY_RATIO		0x0
+#define MCLK_CDREX_RATIO	0x0
+#define ACLK_C2C_200_RATIO	0x1
+#define C2C_CLK_400_RATIO	0x1
+#define PCLK_CDREX_RATIO	0x3
+#define ACLK_CDREX_RATIO	0x1
+#define CLK_DIV_CDREX_VAL	((MCLK_DPHY_RATIO << 20) \
+				| (MCLK_CDREX_RATIO << 16) \
+				| (ACLK_C2C_200_RATIO << 12) \
+				| (C2C_CLK_400_RATIO << 8) \
+				| (PCLK_CDREX_RATIO << 4) \
+				| (ACLK_CDREX_RATIO))
+
+#define MCLK_EFPHY_RATIO	0x4
+#define CLK_DIV_CDREX2_VAL	MCLK_EFPHY_RATIO
+
+/* CLK_DIV_ACP */
+#define CLK_DIV_ACP_VAL	0x12
+
+/* CLK_SRC_TOP0	*/
+#define MUX_ACLK_300_GSCL_SEL		0x1
+#define MUX_ACLK_300_GSCL_MID_SEL	0x0
+#define MUX_ACLK_400_SEL		0x0
+#define MUX_ACLK_333_SEL		0x0
+#define MUX_ACLK_300_DISP1_SEL		0x1
+#define MUX_ACLK_300_DISP1_MID_SEL	0x0
+#define MUX_ACLK_200_SEL		0x0
+#define MUX_ACLK_166_SEL		0x0
+#define CLK_SRC_TOP0_VAL	((MUX_ACLK_300_GSCL_SEL << 25) \
+				| (MUX_ACLK_300_GSCL_MID_SEL << 24) \
+				| (MUX_ACLK_400_SEL << 20) \
+				| (MUX_ACLK_333_SEL << 16) \
+				| (MUX_ACLK_300_DISP1_SEL << 15) \
+				| (MUX_ACLK_300_DISP1_MID_SEL << 14)	\
+				| (MUX_ACLK_200_SEL << 12) \
+				| (MUX_ACLK_166_SEL << 8))
+
+/* CLK_SRC_TOP1	*/
+#define MUX_ACLK_400_ISP_SEL		0x0
+#define MUX_ACLK_400_IOP_SEL		0x0
+#define MUX_ACLK_MIPI_HSI_TXBASE_SEL	0x0
+#define CLK_SRC_TOP1_VAL		((MUX_ACLK_400_ISP_SEL << 24) \
+					|(MUX_ACLK_400_IOP_SEL << 20) \
+					|(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16))
+
+/* CLK_SRC_TOP2 */
+#define MUX_BPLL_USER_SEL	0x1
+#define MUX_MPLL_USER_SEL	0x1
+#define MUX_VPLL_SEL		0x0
+#define MUX_EPLL_SEL		0x0
+#define MUX_CPLL_SEL		0x0
+#define VPLLSRC_SEL		0x0
+#define CLK_SRC_TOP2_VAL	((MUX_BPLL_USER_SEL << 24) \
+				| (MUX_MPLL_USER_SEL << 20) \
+				| (MUX_VPLL_SEL << 16) \
+				| (MUX_EPLL_SEL << 12) \
+				| (MUX_CPLL_SEL << 8) \
+				| (VPLLSRC_SEL))
+/* CLK_SRC_TOP3 */
+#define MUX_ACLK_333_SUB_SEL		0x1
+#define MUX_ACLK_400_SUB_SEL		0x1
+#define MUX_ACLK_266_ISP_SUB_SEL	0x1
+#define MUX_ACLK_266_GPS_SUB_SEL	0x1
+#define MUX_ACLK_300_GSCL_SUB_SEL	0x1
+#define MUX_ACLK_266_GSCL_SUB_SEL	0x1
+#define MUX_ACLK_300_DISP1_SUB_SEL	0x1
+#define MUX_ACLK_200_DISP1_SUB_SEL	0x1
+#define CLK_SRC_TOP3_VAL		((MUX_ACLK_333_SUB_SEL << 24) \
+					| (MUX_ACLK_400_SUB_SEL << 20) \
+					| (MUX_ACLK_266_ISP_SUB_SEL << 16) \
+					| (MUX_ACLK_266_GPS_SUB_SEL << 12) \
+					| (MUX_ACLK_300_GSCL_SUB_SEL << 10) \
+					| (MUX_ACLK_266_GSCL_SUB_SEL << 8) \
+					| (MUX_ACLK_300_DISP1_SUB_SEL << 6) \
+					| (MUX_ACLK_200_DISP1_SUB_SEL << 4))
+
+/* CLK_DIV_TOP0	*/
+#define ACLK_300_RATIO		0x0
+#define ACLK_400_RATIO		0x3
+#define ACLK_333_RATIO		0x2
+#define ACLK_266_RATIO		0x2
+#define ACLK_200_RATIO		0x3
+#define ACLK_166_RATIO		0x5
+#define ACLK_133_RATIO		0x1
+#define ACLK_66_RATIO		0x5
+#define CLK_DIV_TOP0_VAL	((ACLK_300_RATIO << 28) \
+				| (ACLK_400_RATIO << 24) \
+				| (ACLK_333_RATIO << 20) \
+				| (ACLK_266_RATIO << 16) \
+				| (ACLK_200_RATIO << 12) \
+				| (ACLK_166_RATIO << 8) \
+				| (ACLK_133_RATIO << 4) \
+				| (ACLK_66_RATIO))
+
+/* CLK_DIV_TOP1	*/
+#define ACLK_MIPI_HSI_TX_BASE_RATIO	0x3
+#define ACLK_66_PRE_RATIO	0x1
+#define ACLK_400_ISP_RATIO	0x1
+#define ACLK_400_IOP_RATIO	0x1
+#define ACLK_300_GSCL_RATIO	0x0
+#define ACLK_266_GPS_RATIO	0x7
+
+#define CLK_DIV_TOP1_VAL	((ACLK_MIPI_HSI_TX_BASE_RATIO << 28) \
+				| (ACLK_66_PRE_RATIO << 24) \
+				| (ACLK_400_ISP_RATIO << 20) \
+				| (ACLK_400_IOP_RATIO << 16) \
+				| (ACLK_300_GSCL_RATIO << 12) \
+				| (ACLK_266_GPS_RATIO << 8))
+
+/* APLL_LOCK	*/
+#define APLL_LOCK_VAL		(0x3E8)
+/* MPLL_LOCK	*/
+#define MPLL_LOCK_VAL		(0x2F1)
+/* CPLL_LOCK	*/
+#define CPLL_LOCK_VAL		(0x3E8)
+/* EPLL_LOCK	*/
+#define EPLL_LOCK_VAL		(0x2321)
+/* VPLL_LOCK	*/
+#define VPLL_LOCK_VAL		(0x2321)
+/* BPLL_LOCK	*/
+#define BPLL_LOCK_VAL		(0x3E8)
+
+/* CLK_SRC_PERIC0 */
+/* SRC_CLOCK = SCLK_MPLL */
+#define PWM_SEL			0
+#define UART4_SEL		6
+#define UART3_SEL		6
+#define UART2_SEL		6
+#define UART1_SEL		6
+#define UART0_SEL		6
+#define CLK_SRC_PERIC0_VAL	((PWM_SEL << 24) \
+				| (UART4_SEL << 16) \
+				| (UART3_SEL << 12) \
+				| (UART2_SEL << 8) \
+				| (UART1_SEL << 4) \
+				| (UART0_SEL << 0))
+
+#define CLK_SRC_FSYS_VAL	0x66666
+#define CLK_DIV_FSYS0_VAL	0x0BB00000
+#define CLK_DIV_FSYS1_VAL	0x000f000f
+#define CLK_DIV_FSYS2_VAL	0x020f020f
+#define CLK_DIV_FSYS3_VAL	0x000f
+
+/* CLK_DIV_PERIC0	*/
+#define UART5_RATIO		8
+#define UART4_RATIO		8
+#define UART3_RATIO		8
+#define UART2_RATIO		8
+#define UART1_RATIO		8
+#define UART0_RATIO		8
+#define CLK_DIV_PERIC0_VAL	((UART4_RATIO << 16) \
+				| (UART3_RATIO << 12) \
+				| (UART2_RATIO << 8) \
+				| (UART1_RATIO << 4) \
+				| (UART0_RATIO << 0))
+
+/* CLK_DIV_PERIC3	*/
+#define PWM_RATIO		8
+#define CLK_DIV_PERIC3_VAL	(PWM_RATIO << 0)
+
+/* CLK_SRC_LEX */
+#define CLK_SRC_LEX_VAL		0x0
+
+/* CLK_DIV_LEX */
+#define CLK_DIV_LEX_VAL		0x10
+
+/* CLK_DIV_R0X */
+#define CLK_DIV_R0X_VAL		0x10
+
+/* CLK_DIV_L0X */
+#define CLK_DIV_R1X_VAL		0x10
+
+/* SCLK_SRC_ISP */
+#define SCLK_SRC_ISP_VAL	0x600
+/* CLK_DIV_ISP0 */
+#define CLK_DIV_ISP0_VAL	0x31
+
+/* CLK_DIV_ISP1 */
+#define CLK_DIV_ISP1_VAL	0x0
+
+/* CLK_DIV_ISP2 */
+#define CLK_DIV_ISP2_VAL	0x1
+
+#define MPLL_DEC	(MPLL_MDIV * MPLL_MDIV / (MPLL_PDIV * 2^(MPLL_SDIV-1)))
+
+#define DISABLE			0
+#define ENABLE			1
+
+/*
+ * UART GPIO_A0/GPIO_A1 Control Register Value
+ * 0x2: UART Function
+ */
+#define EXYNOS5_GPIO_A0_CON_VAL	0x22222222
+#define EXYNOS5_GPIO_A1_CON_VAL	0x222222
+
+/* ULCON: UART Line Control Value 8N1 */
+#define WORD_LEN_5_BIT		0x00
+#define WORD_LEN_6_BIT		0x01
+#define WORD_LEN_7_BIT		0x02
+#define WORD_LEN_8_BIT		0x03
+
+#define STOP_BIT_1		0x00
+#define STOP_BIT_2		0x01
+
+#define NO_PARITY			0x00
+#define ODD_PARITY			0x4
+#define EVEN_PARITY			0x5
+#define FORCED_PARITY_CHECK_AS_1	0x6
+#define FORCED_PARITY_CHECK_AS_0	0x7
+
+#define INFRAMODE_NORMAL		0x00
+#define INFRAMODE_INFRARED		0x01
+
+#define ULCON_VAL		((INFRAMODE_NORMAL << 6) \
+				| (NO_PARITY << 3) \
+				| (STOP_BIT_1 << 2) \
+				| (WORD_LEN_8_BIT << 0))
+
+/*
+ * UCON: UART Control Value
+ * Tx_interrupt Type: Level
+ * Rx_interrupt Type: Level
+ * Rx Timeout Enabled: Yes
+ * Rx-Error Atatus_Int Enable: Yes
+ * Loop_Back: No
+ * Break Signal: No
+ * Transmit mode : Interrupt request/polling
+ * Receive mode : Interrupt request/polling
+ */
+#define TX_PULSE_INTERRUPT	0
+#define TX_LEVEL_INTERRUPT	1
+#define RX_PULSE_INTERRUPT	0
+#define RX_LEVEL_INTERRUPT	1
+
+#define RX_TIME_OUT		ENABLE
+#define RX_ERROR_STATE_INT_ENB	ENABLE
+#define LOOP_BACK		DISABLE
+#define BREAK_SIGNAL		DISABLE
+
+#define TX_MODE_DISABLED	0X00
+#define TX_MODE_IRQ_OR_POLL	0X01
+#define TX_MODE_DMA		0X02
+
+#define RX_MODE_DISABLED	0X00
+#define RX_MODE_IRQ_OR_POLL	0X01
+#define RX_MODE_DMA		0X02
+
+#define UCON_VAL		((TX_LEVEL_INTERRUPT << 9) \
+				| (RX_LEVEL_INTERRUPT << 8) \
+				| (RX_TIME_OUT << 7) \
+				| (RX_ERROR_STATE_INT_ENB << 6) \
+				| (LOOP_BACK << 5) \
+				| (BREAK_SIGNAL << 4) \
+				| (TX_MODE_IRQ_OR_POLL << 2) \
+				| (RX_MODE_IRQ_OR_POLL << 0))
+
+/*
+ * UFCON: UART FIFO Control Value
+ * Tx FIFO Trigger LEVEL: 2 Bytes (001)
+ * Rx FIFO Trigger LEVEL: 2 Bytes (001)
+ * Tx Fifo Reset: No
+ * Rx Fifo Reset: No
+ * FIFO Enable: Yes
+ */
+#define TX_FIFO_TRIGGER_LEVEL_0_BYTES	0x00
+#define TX_FIFO_TRIGGER_LEVEL_2_BYTES	0x1
+#define TX_FIFO_TRIGGER_LEVEL_4_BYTES	0x2
+#define TX_FIFO_TRIGGER_LEVEL_6_BYTES	0x3
+#define TX_FIFO_TRIGGER_LEVEL_8_BYTES	0x4
+#define TX_FIFO_TRIGGER_LEVEL_10_BYTES	0x5
+#define TX_FIFO_TRIGGER_LEVEL_12_BYTES	0x6
+#define TX_FIFO_TRIGGER_LEVEL_14_BYTES	0x7
+
+#define RX_FIFO_TRIGGER_LEVEL_2_BYTES	0x0
+#define RX_FIFO_TRIGGER_LEVEL_4_BYTES	0x1
+#define RX_FIFO_TRIGGER_LEVEL_6_BYTES	0x2
+#define RX_FIFO_TRIGGER_LEVEL_8_BYTES	0x3
+#define RX_FIFO_TRIGGER_LEVEL_10_BYTES	0x4
+#define RX_FIFO_TRIGGER_LEVEL_12_BYTES	0x5
+#define RX_FIFO_TRIGGER_LEVEL_14_BYTES	0x6
+#define RX_FIFO_TRIGGER_LEVEL_16_BYTES	0x7
+
+#define TX_FIFO_TRIGGER_LEVEL		TX_FIFO_TRIGGER_LEVEL_2_BYTES
+#define RX_FIFO_TRIGGER_LEVEL		RX_FIFO_TRIGGER_LEVEL_4_BYTES
+#define TX_FIFO_RESET			DISABLE
+#define RX_FIFO_RESET			DISABLE
+#define FIFO_ENABLE			ENABLE
+#define UFCON_VAL			((TX_FIFO_TRIGGER_LEVEL << 8) \
+					| (RX_FIFO_TRIGGER_LEVEL << 4) \
+					| (TX_FIFO_RESET << 2) \
+					| (RX_FIFO_RESET << 1) \
+					| (FIFO_ENABLE << 0))
+/*
+ * Baud Rate Division Value
+ * 115200 BAUD:
+ * UBRDIV_VAL = SCLK_UART/((115200 * 16) - 1)
+ * UBRDIV_VAL = (800 MHz)/((115200 * 16) - 1)
+ */
+#define UBRDIV_VAL		0x2F
+
+/*
+ * Fractional Part of Baud Rate Divisor:
+ * 115200 BAUD:
+ * UBRFRACVAL = ((((SCLK_UART*10/(115200*16) -10))%10)*16/10)
+ * UBRFRACVAL = ((((800MHz*10/(115200*16) -10))%10)*16/10)
+ */
+#define UFRACVAL_VAL		0x3
+
+/*
+ * TZPC Register Value :
+ * R0SIZE: 0x0 : Size of secured ram
+ */
+#define R0SIZE			0x0
+
+/*
+ * TZPC Decode Protection Register Value :
+ * DECPROTXSET: 0xFF : Set Decode region to non-secure
+ */
+#define DECPROTXSET		0xFF
+#endif
diff --git a/boards.cfg b/boards.cfg
index 0b32532..3676e9d 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -218,6 +218,7 @@ s5p_goni                     arm         armv7       goni                samsung
 smdkc100                     arm         armv7       smdkc100            samsung        s5pc1xx
 origen			     arm	 armv7	     origen		 samsung	exynos
 s5pc210_universal            arm         armv7       universal_c210      samsung        exynos
+smdk5250		     arm	 armv7	     smdk5250		 samsung	exynos
 smdkv310		     arm	 armv7	     smdkv310		 samsung	exynos
 harmony                      arm         armv7       harmony             nvidia         tegra2
 seaboard                     arm         armv7       seaboard            nvidia         tegra2
diff --git a/include/configs/smdk5250.h b/include/configs/smdk5250.h
new file mode 100644
index 0000000..9962c14
--- /dev/null
+++ b/include/configs/smdk5250.h
@@ -0,0 +1,185 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG SMDK5250 (EXYNOS5250) board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_SAMSUNG		1	/* in a SAMSUNG core */
+#define CONFIG_S5P		1	/* S5P Family */
+#define CONFIG_EXYNOS5		1	/* which is in a Exynos5 Family */
+#define CONFIG_CPU_EXYNOS5250	1	/* which is in a Exynos5250 */
+#define CONFIG_SMDK5250		1	/* which is in a SMDK5250 */
+
+#include <asm/arch/cpu.h>		/* get chip and board defs */
+
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Keep L2 Cache Disabled */
+#define CONFIG_L2_OFF			1
+#define CONFIG_SYS_DCACHE_OFF		1
+
+#define CONFIG_SYS_SDRAM_BASE		0x40000000
+#define CONFIG_SYS_TEXT_BASE		0x43E00000
+
+/* input clock of PLL: SMDK5250 has 24MHz input clock */
+#define CONFIG_SYS_CLK_FREQ		24000000
+
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_EDITING
+
+/* MACH_TYPE_ORIGEN macro will be removed once added to mach-types */
+#define MACH_TYPE_SMDK5250		3774
+#define CONFIG_MACH_TYPE		MACH_TYPE_SMDK5250
+
+/* Power Down Modes */
+#define S5P_CHECK_SLEEP			0x00000BAD
+#define S5P_CHECK_DIDLE			0xBAD00000
+#define S5P_CHECK_LPA			0xABAD0000
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (1 << 20))
+
+/* select serial console configuration */
+#define CONFIG_SERIAL_MULTI		1
+#define CONFIG_SERIAL1			1	/* use SERIAL 1 */
+#define CONFIG_BAUDRATE			115200
+#define EXYNOS5_DEFAULT_UART_OFFSET	0x010000
+
+/* SD/MMC configuration */
+#define CONFIG_GENERIC_MMC		1
+#define CONFIG_MMC			1
+#define CONFIG_S5P_MMC			1
+
+/* PWM */
+#define CONFIG_PWM			1
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Command definition*/
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+
+#define CONFIG_BOOTDELAY		3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#define CONFIG_BOOTCOMMAND	"fatload mmc 0 40007000 uImage; bootm 40007000"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_PROMPT		"SMDK5250 # "
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE		384	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
+#define CONFIG_DEFAULT_CONSOLE		"console=ttySAC1,115200n8\0"
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x5E00000)
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x3E00000)
+
+#define CONFIG_SYS_HZ			1000
+
+/* valid baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/* Stack sizes */
+#define CONFIG_STACKSIZE		(256 << 10)	/* 256KB */
+
+#define CONFIG_NR_DRAM_BANKS	8
+#define SDRAM_BANK_SIZE		(256UL << 20UL)	/* 256 MB */
+#define PHYS_SDRAM_1		CONFIG_SYS_SDRAM_BASE
+#define PHYS_SDRAM_1_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_2		(CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
+#define PHYS_SDRAM_2_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_3		(CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_3_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_4		(CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_4_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_5		(CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_5_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_6		(CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_6_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_7		(CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_7_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_8		(CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_8_SIZE	SDRAM_BANK_SIZE
+
+#define CONFIG_SYS_MONITOR_BASE	0x00000000
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH		1
+#undef CONFIG_CMD_IMLS
+#define CONFIG_IDENT_STRING		" for SMDK5250"
+
+
+#define CONFIG_ENV_IS_IN_MMC		1
+#define CONFIG_SYS_MMC_ENV_DEV		0
+
+#define CONFIG_SECURE_BL1_ONLY
+
+/* Secure FW size configuration */
+#ifdef	CONFIG_SECURE_BL1_ONLY
+#define	CONFIG_SEC_FW_SIZE		(8 << 10)	/* 8KB */
+#else
+#define	CONFIG_SEC_FW_SIZE		0
+#endif
+
+/* Configuration of BL1, BL2, ENV Blocks on mmc */
+#define CONFIG_RES_BLOCK_SIZE	(512)
+#define CONFIG_BL1_SIZE		(16 << 10) /*16 K reserved for BL1*/
+#define	CONFIG_BL2_SIZE		(512UL << 10UL)	/* 512 KB */
+#define CONFIG_ENV_SIZE		(16 << 10)	/* 16 KB */
+
+#define CONFIG_BL1_OFFSET	(CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE)
+#define CONFIG_BL2_OFFSET	(CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
+#define CONFIG_ENV_OFFSET	(CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE)
+
+/* U-boot copy size from boot Media to DRAM.*/
+#define BL2_START_OFFSET	(CONFIG_BL2_OFFSET/512)
+#define BL2_SIZE_BLOC_COUNT	(CONFIG_BL2_SIZE/512)
+#define CONFIG_DOS_PARTITION		1
+
+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_LOAD_ADDR - 0x1000000)
+#define MMC_MAX_CHANNEL		5
+
+/* Enable devicetree support */
+#define CONFIG_OF_LIBFDT
+
+#endif	/* __CONFIG_H */
-- 
1.7.5.4



More information about the U-Boot mailing list