[U-Boot] [PATCH 2/2] tt01: add MMC support

[Helmut Raiger]

board_mmc_init() initializes the pins of SDHC1 and
turns on V_MMC1 of the PMIC. Config adds support for EXT2
and FAT.

Signed-off-by: Helmut Raiger <helmut.raiger at hale.at>
---
 board/hale/tt01/tt01.c |   32 ++++++++++++++++++++++++++++++--
 include/configs/tt01.h |   12 ++++++++++++
 2 files changed, 42 insertions(+), 2 deletions(-)

diff --git a/board/hale/tt01/tt01.c b/board/hale/tt01/tt01.c
index 2995c8f..4b6e770 100644
--- a/board/hale/tt01/tt01.c
+++ b/board/hale/tt01/tt01.c
@@ -175,8 +175,6 @@ int board_init(void)
 
 int board_late_init(void)
 {
-	pmic_init();
-
 #ifdef CONFIG_HW_WATCHDOG
 	mxc_hw_watchdog_enable();
 #endif
@@ -190,6 +188,36 @@ int checkboard(void)
 	return 0;
 }
 
+#ifdef CONFIG_MXC_MMC
+int board_mmc_init(bd_t *bis)
+{
+	u32 val;
+	struct pmic *p;
+
+	/*
+	* this is the first driver to use the pmic, so call
+	* pmic_init() here. board_late_init() is too late for
+	* the MMC driver.
+	*/
+	pmic_init();
+	p = get_pmic();
+
+	/* configure pins for SDHC1 only */
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SD1_CLK, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SD1_CMD, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SD1_DATA0, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SD1_DATA1, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SD1_DATA2, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SD1_DATA3, MUX_CTL_FUNC));
+
+	/* turn on power V_MMC1, bit 18 is the VMMC1 enable */
+	if (pmic_reg_read(p, 33, &val) < 0)
+		pmic_reg_write(p, 33, val | 0x040000);
+
+	return mxc_mmc_init(bis);
+}
+#endif
+
 int board_eth_init(bd_t *bis)
 {
 	int rc = 0;
diff --git a/include/configs/tt01.h b/include/configs/tt01.h
index a553712..6846816 100644
--- a/include/configs/tt01.h
+++ b/include/configs/tt01.h
@@ -180,6 +180,11 @@
 #define CONFIG_SMC911X_BASE		(CS4_BASE+0x200000)
 #define CONFIG_SMC911X_16_BIT
 
+/* mmc driver */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MXC_MMC
+#define CONFIG_MXC_MCI_REGS_BASE       SDHC1_BASE_ADDR
 /*
  * Command definition
  */
@@ -229,6 +234,13 @@
 
 #define CONFIG_CMDLINE_EDITING
 
+/* MMC boot support */
+#define CONFIG_CMD_MMC
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+
 #define CONFIG_NAND_MXC
 #define CONFIG_SYS_MAX_NAND_DEVICE		1
 #define CONFIG_SYS_NAND_MAX_CHIPS		1
-- 
1.7.4.4



--
Scanned by MailScanner.