[U-Boot] [PATCH 3/3 v3] devkit3250: add Timll DevKit3250 board initial support
Marek Vasut
marek.vasut at gmail.com
Wed Jan 11 23:08:50 CET 2012
> On 11.01.2012 22:56, Marek Vasut wrote:
> >> This change adds a basic support for Embest/Timll DevKit3250 board,
> >> NOR and UART are the only supported peripherals for a moment. The board
> >> doesn't require low-level init, because the initial SDRAM and GPIO
> >> configuration is performed during kickstart bootloader execution.
> >>
> >> Signed-off-by: Vladimir Zapolskiy<vz at mleia.com>
> >> ---
> >> Changes from v2 to v3:
> >> * updated a relocation address
> >> * combined a record in maintainers file into the patch
> >> * use high speed UART2 by default
> >>
> >> Changes from v1 to v2:
> >> * corrected address in GPLv2+ licence header in files
> >> * removed clean and distclean targets from board makefile
> >> * do not set machine id explicitly, if CONFIG_MACH_TYPE is defined
> >> * minor indentation cleanups
> >>
> >> MAINTAINERS | 4 +
> >> board/timll/devkit3250/Makefile | 44 +++++++++++++
> >> board/timll/devkit3250/devkit3250.c | 71 ++++++++++++++++++++
> >> boards.cfg | 1 +
> >> include/configs/devkit3250.h | 121
> >>
> >> +++++++++++++++++++++++++++++++++++ 5 files changed, 241 insertions(+),
> >> 0 deletions(-)
> >>
> >> create mode 100644 board/timll/devkit3250/Makefile
> >> create mode 100644 board/timll/devkit3250/devkit3250.c
> >> create mode 100644 include/configs/devkit3250.h
> >>
> >> diff --git a/MAINTAINERS b/MAINTAINERS
> >> index 4bf12b5..68dedae 100644
> >> --- a/MAINTAINERS
> >> +++ b/MAINTAINERS
> >> @@ -914,6 +914,10 @@ Sughosh Ganu<urwithsughosh at gmail.com>
> >>
> >> hawkboard ARM926EJS (OMAP-L138)
> >>
> >> +Vladimir Zapolskiy<vz at mleia.com>
> >> +
> >> + devkit3250 lpc32xx
> >> +
> >>
> >> ----------------------------------------------------------------------
> >> ---
> >>
> >> Unknown / orphaned boards:
> >> diff --git a/board/timll/devkit3250/Makefile
> >> b/board/timll/devkit3250/Makefile new file mode 100644
> >> index 0000000..ea7827c
> >> --- /dev/null
> >> +++ b/board/timll/devkit3250/Makefile
> >> @@ -0,0 +1,44 @@
> >> +#
> >> +# Copyright (C) 2011 by Vladimir Zapolskiy<vz at mleia.com>
> >> +# Copyright (C) 2008, Guennadi Liakhovetski<lg at denx.de>
> >> +#
> >> +# See file CREDITS for list of people who contributed to this
> >> +# project.
> >> +#
> >> +# This program is free software; you can redistribute it and/or
> >> +# modify it under the terms of the GNU General Public License as
> >> +# published by the Free Software Foundation; either version 2 of
> >> +# the License, or (at your option) any later version.
> >> +#
> >> +# This program is distributed in the hope that it will be useful,
> >> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> >> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> >> +# GNU General Public License for more details.
> >> +#
> >> +# You should have received a copy of the GNU General Public License
> >> +# along with this program; if not, write to the Free Software
> >> +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> >> +# MA 02110-1301, USA.
> >> +#
> >> +
> >> +include $(TOPDIR)/config.mk
> >> +
> >> +LIB = $(obj)lib$(BOARD).o
> >> +
> >> +COBJS := devkit3250.o
> >> +
> >> +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> >> +OBJS := $(addprefix $(obj),$(COBJS))
> >> +SOBJS := $(addprefix $(obj),$(SOBJS))
> >> +
> >> +$(LIB): $(obj).depend $(OBJS) $(SOBJS)
> >> + $(call cmd_link_o_target, $(OBJS) $(SOBJS))
> >> +
> >> +#######################################################################
> >> ## +
> >> +# defines $(obj).depend target
> >> +include $(SRCTREE)/rules.mk
> >> +
> >> +sinclude $(obj).depend
> >> +
> >> +#######################################################################
> >> ## diff --git a/board/timll/devkit3250/devkit3250.c
> >> b/board/timll/devkit3250/devkit3250.c new file mode 100644
> >> index 0000000..461012d
> >> --- /dev/null
> >> +++ b/board/timll/devkit3250/devkit3250.c
> >> @@ -0,0 +1,71 @@
> >> +/*
> >> + * Embest/Timll DevKit3250 board support
> >> + *
> >> + * Copyright (C) 2011 Vladimir Zapolskiy<vz at mleia.com>
> >> + *
> >> + * This program is free software; you can redistribute it and/or
> >> + * modify it under the terms of the GNU General Public License as
> >> + * published by the Free Software Foundation; either version 2 of
> >> + * the License, or (at your option) any later version.
> >> + *
> >> + * This program is distributed in the hope that it will be useful,
> >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> >> + * GNU General Public License for more details.
> >> + *
> >> + * You should have received a copy of the GNU General Public License
> >> + * along with this program; if not, write to the Free Software
> >> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> >> + * MA 02110-1301, USA.
> >> + */
> >> +
> >> +#include<common.h>
> >> +#include<asm/arch/sys_proto.h>
> >> +#include<asm/arch/cpu.h>
> >> +#include<asm/arch/emc.h>
> >> +
> >> +DECLARE_GLOBAL_DATA_PTR;
> >> +
> >> +static struct emc_t *emc = (struct emc_t *)EMC_BASE;
> >> +
> >> +int board_early_init_f(void)
> >> +{
> >> + lpc32xx_uart_init(CONFIG_SYS_LPC32XX_UART);
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +int board_init(void)
> >> +{
> >> + /*
> >> + * It might be necessary to flush data cache, if U-boot is loaded
> >> + * from kickstart bootloader, e.g. from S1L loader
> >> + */
> >> + flush_cache(0, 0);
> >
> > You're flushing no area here ... also, shouldn't this go to CPU init code
> > ?
>
> That's just a complete cache flush, from arch/arm/lib/cache.c size
> argument is actually redundant.
>
> Basically this should go into low level init, but the board has a
> kickstart bootloader, so generally no need to have low level init at all
> for it.
What are you talking about ? This should go into CPU init then, right ? If you
have crap IPL -- I suspect for all those CPUs of this series -- then this is
common for all CPUs and should go into CPU init.
M
>
> >> +
> >> + /* adress of boot parameters */
> >> + gd->bd->bi_boot_params = CONFIG_ENV_ADDR;
> >> +
> >> +#ifdef CONFIG_SYS_FLASH_CFI
> >> + /* Use 16-bit memory interface for NOR Flash */
> >> + emc->stat[0].config = EMC_STAT_CONFIG_PB | EMC_STAT_CONFIG_16BIT;
> >> +
> >> + /* Change the NOR timings to optimum value to get maximum bandwidth */
> >> + emc->stat[0].waitwen = EMC_STAT_WAITWEN(1);
> >> + emc->stat[0].waitoen = EMC_STAT_WAITOEN(1);
> >> + emc->stat[0].waitrd = EMC_STAT_WAITRD(12);
> >> + emc->stat[0].waitpage = EMC_STAT_WAITPAGE(12);
> >> + emc->stat[0].waitwr = EMC_STAT_WAITWR(5);
> >> + emc->stat[0].waitturn = EMC_STAT_WAITTURN(2);
> >> +#endif
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +int dram_init(void)
> >> +{
> >> + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
> >> + CONFIG_SYS_SDRAM_SIZE);
> >> +
> >> + return 0;
> >> +}
> >> diff --git a/boards.cfg b/boards.cfg
> >> index 0b32532..24a98fe 100644
> >> --- a/boards.cfg
> >> +++ b/boards.cfg
> >> @@ -176,6 +176,7 @@ omap730p2_cs0boot arm arm926ejs
> >> omap730p2 ti omap omap730p2_cs3boot arm
> >> arm926ejs omap730p2 ti omap
omap730p2:CS3_BOOT
> >> edminiv2 arm arm926ejs -
> >> LaCie orion5x dkb arm arm926ejs -
> >>
> >> Marvell pantheon +devkit3250 arm
> >>
> >> arm926ejs devkit3250 timll lpc32xx versatileab
> >>
> >> arm arm926ejs versatile armltd
> >>
> >> versatile versatile:ARCH_VERSATILE_AB versatilepb arm
> >>
> >> arm926ejs versatile armltd versatile
> >>
> >> versatile:ARCH_VERSATILE_PB versatileqemu arm
> >> arm926ejs versatile armltd versatile
> >> versatile:ARCH_VERSATILE_QEMU,ARCH_VERSATILE_PB diff --git
> >> a/include/configs/devkit3250.h b/include/configs/devkit3250.h new file
> >> mode 100644
> >> index 0000000..360a041
> >> --- /dev/null
> >> +++ b/include/configs/devkit3250.h
> >> @@ -0,0 +1,121 @@
> >> +/*
> >> + * Embest/Timll DevKit3250 board configuration file
> >> + *
> >> + * Copyright (C) 2011 Vladimir Zapolskiy<vz at mleia.com>
> >> + *
> >> + * This program is free software; you can redistribute it and/or
> >> + * modify it under the terms of the GNU General Public License
> >> + * as published by the Free Software Foundation; either version 2
> >> + * of the License, or (at your option) any later version.
> >> + *
> >> + * This program is distributed in the hope that it will be useful,
> >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> >> + * GNU General Public License for more details.
> >> + *
> >> + * You should have received a copy of the GNU General Public License
> >> + * along with this program; if not, write to the Free Software
> >> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> >> + * MA 02110-1301, USA.
> >> + */
> >> +
> >> +#ifndef __CONFIG_DEVKIT3250_H__
> >> +#define __CONFIG_DEVKIT3250_H__
> >> +
> >> +/* SoC and board defines */
> >> +#include<asm/sizes.h>
> >> +#include<asm/arch/cpu.h>
> >> +
> >> +/*
> >> + * Define DevKit3250 machine type by hand until it lands in mach-types
> >> + */
> >> +#define MACH_TYPE_DEVKIT3250 3697
> >> +#define CONFIG_MACH_TYPE MACH_TYPE_DEVKIT3250
> >> +
> >> +#define CONFIG_SYS_ICACHE_OFF
> >> +#define CONFIG_SYS_DCACHE_OFF
> >> +#define CONFIG_SKIP_LOWLEVEL_INIT
> >> +#define CONFIG_BOARD_EARLY_INIT_F
> >> +
> >> +/*
> >> + * Memory configurations
> >> + */
> >> +#define CONFIG_NR_DRAM_BANKS 1
> >> +#define CONFIG_STACKSIZE SZ_32K
> >> +#define CONFIG_SYS_MALLOC_LEN SZ_1M
> >> +#define CONFIG_SYS_GBL_DATA_SIZE 128
> >> +#define CONFIG_SYS_SDRAM_BASE EMC_DYCS0_BASE
> >> +#define CONFIG_SYS_SDRAM_SIZE SZ_64M
> >> +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
> >> +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - SZ_1M)
> >> +
> >> +#define CONFIG_SYS_TEXT_BASE 0x83FA0000
> >> +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_MEMTEST_START + SZ_32K)
> >> +
> >> +#define CONFIG_SYS_INIT_RAM_SIZE SZ_4K
> >> +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \
> >> + CONFIG_SYS_INIT_RAM_SIZE - \
> >> + GENERATED_GBL_DATA_SIZE)
> >> +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET
> >> +
> >> +/*
> >> + * Serial Driver
> >> + */
> >> +#define CONFIG_SYS_LPC32XX_UART 2 /* UART2 */
> >> +#define CONFIG_BAUDRATE 115200
> >> +
> >> +/*
> >> + * NOR Flash
> >> + */
> >> +#define CONFIG_CMD_FLASH
> >> +#define CONFIG_SYS_MAX_FLASH_BANKS 1
> >> +#define CONFIG_SYS_MAX_FLASH_SECT 71
> >> +#define CONFIG_SYS_FLASH_BASE EMC_CS0_BASE
> >> +#define CONFIG_SYS_FLASH_SIZE SZ_4M
> >> +#define CONFIG_SYS_FLASH_CFI
> >> +
> >> +/*
> >> + * U-Boot General Configurations
> >> + */
> >> +#define CONFIG_SYS_LONGHELP
> >> +#define CONFIG_SYS_PROMPT "=> "
> >> +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size
> >> */ +#define CONFIG_SYS_PBSIZE \
> >> + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
> >> +#define CONFIG_SYS_MAXARGS 16
> >> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> >> +
> >> +#define CONFIG_AUTO_COMPLETE
> >> +#define CONFIG_CMDLINE_EDITING
> >> +#define CONFIG_VERSION_VARIABLE
> >> +#define CONFIG_DISPLAY_CPUINFO
> >> +#define CONFIG_DOS_PARTITION
> >> +
> >> +#define CONFIG_ENV_IS_NOWHERE
> >> +#define CONFIG_ENV_SIZE SZ_128K
> >> +#define CONFIG_ENV_ADDR 0x80000100
> >> +
> >> +/*
> >> + * U-Boot Commands
> >> + */
> >> +#include<config_cmd_default.h>
> >> +#define CONFIG_CMD_CACHE
> >> +
> >> +/*
> >> + * Boot Linux
> >> + */
> >> +#define CONFIG_CMDLINE_TAG
> >> +#define CONFIG_SETUP_MEMORY_TAGS
> >> +#define CONFIG_ZERO_BOOTDELAY_CHECK
> >> +#define CONFIG_BOOTDELAY 3
> >> +
> >> +#define CONFIG_BOOTFILE "uImage"
> >> +#define CONFIG_BOOTARGS "console=ttyS2,115200n8"
> >> +#define CONFIG_LOADADDR 0x80008000
> >> +
> >> +/*
> >> + * SoC specific configuration
> >> + */
> >> +#include<asm/arch/config.h>
> >> +
> >> +#endif /* __CONFIG_DEVKIT3250_H__*/
> >
> > Otherwise ok
>
> Thanks for review.
More information about the U-Boot
mailing list