[U-Boot] [PATCH 3/3] mx28evk: add SPI support

[Matthias Fuchs]

On 01/18/2012 05:07 PM, Marek Vasut wrote:
>> This patch adds SPI support for the MX28EVK. Support for
>> an optionally installed SPI flash is also added. An example
>> configuration for redundant envrionment from SPI flash is also
>> added but disabled by default.
>>
>> This patch has been tested on a MX28EVK Rev. D with an installed
>> SST25VF032B 32Mbit SPI flash.
>>
>> Signed-off-by: Matthias Fuchs <matthias.fuchs at esd.eu>
>> ---
>>  board/freescale/mx28evk/iomux.c |    8 +++++++
>>  include/configs/mx28evk.h       |   44
>> ++++++++++++++++++++++++++++++++++++-- 2 files changed, 49 insertions(+),
>> 3 deletions(-)
>>
>> diff --git a/board/freescale/mx28evk/iomux.c
>> b/board/freescale/mx28evk/iomux.c index 904e3f3..396761b 100644
>> --- a/board/freescale/mx28evk/iomux.c
>> +++ b/board/freescale/mx28evk/iomux.c
>> @@ -28,6 +28,7 @@
>>  #define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
>>  #define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
>>  #define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
>> +#define	MUX_CONFIG_SSP2	(MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_PULLUP)
>>
>>  const iomux_cfg_t iomux_setup[] = {
>>  	/* DUART */
>> @@ -130,6 +131,13 @@ const iomux_cfg_t iomux_setup[] = {
>>  	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
>>  	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
>>  	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
>> +
>> +	/* SPI2 (for SPI flash) */
>> +	MX28_PAD_SSP2_SCK__SSP2_SCK | MUX_CONFIG_SSP2,
>> +	MX28_PAD_SSP2_MOSI__SSP2_CMD | MUX_CONFIG_SSP2,
>> +	MX28_PAD_SSP2_MISO__SSP2_D0 | MUX_CONFIG_SSP2,
>> +	MX28_PAD_SSP2_SS0__SSP2_D3 |
>> +		(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
>>  };
>>
>>  void board_init_ll(void)
>> diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
>> index 8f791aa..04967d7 100644
>> --- a/include/configs/mx28evk.h
>> +++ b/include/configs/mx28evk.h
>> @@ -64,6 +64,8 @@
>>  #define CONFIG_CMD_NET
>>  #define CONFIG_CMD_NFS
>>  #define CONFIG_CMD_PING
>> +#define CONFIG_CMD_SF
>> +#define CONFIG_CMD_SPI
>>  #define CONFIG_CMD_USB
>>
>>  /*
>> @@ -127,9 +129,11 @@
>>   * MMC Driver
>>   */
>>  #define CONFIG_ENV_IS_IN_MMC
>> -#define CONFIG_ENV_OFFSET	(256 * 1024)
>> -#define CONFIG_ENV_SIZE	(16 * 1024)
>> -#define CONFIG_SYS_MMC_ENV_DEV 0
>> +#ifdef CONFIG_ENV_IS_IN_MMC
>> + #define CONFIG_ENV_OFFSET	(256 * 1024)
>> + #define CONFIG_ENV_SIZE	(16 * 1024)
>> + #define CONFIG_SYS_MMC_ENV_DEV 0
>> +#endif
>>  #define CONFIG_CMD_SAVEENV
>>  #ifdef	CONFIG_CMD_MMC
>>  #define CONFIG_MMC
>> @@ -170,6 +174,40 @@
>>  #endif
>>
>>  /*
>> + * SPI
>> + */
>> +#ifdef CONFIG_CMD_SPI
>> +#define CONFIG_HARD_SPI
>> +#define CONFIG_MXS_SPI
>> +#define CONFIG_SPI_HALF_DUPLEX
>> +#define CONFIG_DEFAULT_SPI_BUS		2
>> +#define CONFIG_DEFAULT_SPI_MODE		SPI_MODE_0
>> +
>> +/* SPI Flash */
>> +#ifdef CONFIG_CMD_SF
>> +#define CONFIG_SPI_FLASH
>> +/* this may vary and depends on the installed chip */
>> +#define CONFIG_SPI_FLASH_SST
>> +#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
>> +#define CONFIG_SF_DEFAULT_SPEED		24000000
>> +
>> +/* (redundant) environemnt in SPI flash */
>> +#undef CONFIG_ENV_IS_IN_SPI_FLASH
>> +#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
>> +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
>> +#define CONFIG_ENV_SIZE			0x1000		/* 4KB */
>> +#define CONFIG_ENV_OFFSET		0x40000		/* 256K */
>> +#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
>> +#define CONFIG_ENV_SECT_SIZE		0x1000
>> +#define CONFIG_ENV_SPI_CS		0
>> +#define CONFIG_ENV_SPI_BUS		2
>> +#define CONFIG_ENV_SPI_MAX_HZ		24000000
>> +#define CONFIG_ENV_SPI_MODE		SPI_MODE_0
>> +#endif
>> +#endif
>> +#endif
>> +
>> +/*
>>   * Boot Linux
>>   */
>>  #define CONFIG_CMDLINE_TAG
> 
> Hm, good ... so the SPI flash works now with no modifications ?
Of course not! The SPI driver needs to be fixed. Either by my previously 
posted patch or by god's hands :-)

Fabio asked for this patch in order to test my SPI driver fix.
But I think this is independant from each other.

Matthias