[U-Boot] [PATCH 05/10 V5] EXYNOS5: CLOCK: Add clock support for Exynos5250 Rev 1.0
Rajeshwari Shinde
rajeshwari.s at samsung.com
Mon Jul 2 13:36:40 CEST 2012
Add new clock values for Exynos5250 Rev 1.0
Signed-off-by: Hatim Ali <hatim.rv at samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s at samsung.com>
---
Changes in V2:
- None.
Changes in V3:
- Set Peric3 clock for PWM Ratio.
Changes in V4:
- None.
Changes in V5:
- None
board/samsung/smdk5250/clock_init.c | 714 +++++++++++++++++++++++++++++------
board/samsung/smdk5250/clock_init.h | 149 ++++++++
board/samsung/smdk5250/setup.h | 715 ++++++++++++++++++++---------------
3 files changed, 1138 insertions(+), 440 deletions(-)
create mode 100644 board/samsung/smdk5250/clock_init.h
diff --git a/board/samsung/smdk5250/clock_init.c b/board/samsung/smdk5250/clock_init.c
index 305842d..c009ae5 100644
--- a/board/samsung/smdk5250/clock_init.c
+++ b/board/samsung/smdk5250/clock_init.c
@@ -22,181 +22,645 @@
* MA 02111-1307 USA
*/
+#include <common.h>
#include <config.h>
-#include <version.h>
#include <asm/io.h>
+#include <asm/arch/clk.h>
#include <asm/arch/clock.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/gpio.h>
+#include <asm/arch/spl.h>
+
+#include "clock_init.h"
#include "setup.h"
-void system_clock_init()
+DECLARE_GLOBAL_DATA_PTR;
+
+struct arm_clk_ratios arm_clk_ratios[] = {
+ {
+ .arm_freq_mhz = 600,
+
+ .apll_mdiv = 0xc8,
+ .apll_pdiv = 0x4,
+ .apll_sdiv = 0x1,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x1,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x2,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x1,
+ .arm_ratio = 0x0,
+ }, {
+ .arm_freq_mhz = 800,
+
+ .apll_mdiv = 0x64,
+ .apll_pdiv = 0x3,
+ .apll_sdiv = 0x0,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x1,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x3,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x2,
+ .arm_ratio = 0x0,
+ }, {
+ .arm_freq_mhz = 1000,
+
+ .apll_mdiv = 0x7d,
+ .apll_pdiv = 0x3,
+ .apll_sdiv = 0x0,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x1,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x4,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x2,
+ .arm_ratio = 0x0,
+ }, {
+ .arm_freq_mhz = 1200,
+
+ .apll_mdiv = 0x96,
+ .apll_pdiv = 0x3,
+ .apll_sdiv = 0x0,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x3,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x5,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x3,
+ .arm_ratio = 0x0,
+ }, {
+ .arm_freq_mhz = 1400,
+
+ .apll_mdiv = 0xaf,
+ .apll_pdiv = 0x3,
+ .apll_sdiv = 0x0,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x3,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x6,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x3,
+ .arm_ratio = 0x0,
+ }, {
+ .arm_freq_mhz = 1700,
+
+ .apll_mdiv = 0x1a9,
+ .apll_pdiv = 0x6,
+ .apll_sdiv = 0x0,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x3,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x6,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x3,
+ .arm_ratio = 0x0,
+ }
+};
+struct mem_timings mem_timings[] = {
+ {
+ .mem_manuf = MEM_MANUF_ELPIDA,
+ .mem_type = DDR_MODE_DDR3,
+ .frequency_mhz = 800,
+ .mpll_mdiv = 0xc8,
+ .mpll_pdiv = 0x3,
+ .mpll_sdiv = 0x0,
+ .cpll_mdiv = 0xde,
+ .cpll_pdiv = 0x4,
+ .cpll_sdiv = 0x2,
+ .gpll_mdiv = 0x215,
+ .gpll_pdiv = 0xc,
+ .gpll_sdiv = 0x1,
+ .epll_mdiv = 0x60,
+ .epll_pdiv = 0x3,
+ .epll_sdiv = 0x3,
+ .vpll_mdiv = 0x96,
+ .vpll_pdiv = 0x3,
+ .vpll_sdiv = 0x2,
+
+ .bpll_mdiv = 0x64,
+ .bpll_pdiv = 0x3,
+ .bpll_sdiv = 0x0,
+ .pclk_cdrex_ratio = 0x5,
+ .direct_cmd_msr = {
+ 0x00020018, 0x00030000, 0x00010042, 0x00000d70
+ },
+ .timing_ref = 0x000000bb,
+ .timing_row = 0x8c36650e,
+ .timing_data = 0x3630580b,
+ .timing_power = 0x41000a44,
+ .phy0_dqs = 0x08080808,
+ .phy1_dqs = 0x08080808,
+ .phy0_dq = 0x08080808,
+ .phy1_dq = 0x08080808,
+ .phy0_tFS = 0x4,
+ .phy1_tFS = 0x4,
+ .phy0_pulld_dqs = 0xf,
+ .phy1_pulld_dqs = 0xf,
+
+ .lpddr3_ctrl_phy_reset = 0x1,
+ .ctrl_start_point = 0x10,
+ .ctrl_inc = 0x10,
+ .ctrl_start = 0x1,
+ .ctrl_dll_on = 0x1,
+ .ctrl_ref = 0x8,
+
+ .ctrl_force = 0x1a,
+ .ctrl_rdlat = 0x0b,
+ .ctrl_bstlen = 0x08,
+
+ .fp_resync = 0x8,
+ .iv_size = 0x7,
+ .dfi_init_start = 1,
+ .aref_en = 1,
+
+ .rd_fetch = 0x3,
+
+ .zq_mode_dds = 0x7,
+ .zq_mode_term = 0x1,
+ .zq_mode_noterm = 0,
+
+ /*
+ * Dynamic Clock: Always Running
+ * Memory Burst length: 8
+ * Number of chips: 1
+ * Memory Bus width: 32 bit
+ * Memory Type: DDR3
+ * Additional Latancy for PLL: 0 Cycle
+ */
+ .memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
+ DMC_MEMCONTROL_DPWRDN_DISABLE |
+ DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
+ DMC_MEMCONTROL_TP_DISABLE |
+ DMC_MEMCONTROL_DSREF_ENABLE |
+ DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
+ DMC_MEMCONTROL_MEM_TYPE_DDR3 |
+ DMC_MEMCONTROL_MEM_WIDTH_32BIT |
+ DMC_MEMCONTROL_NUM_CHIP_1 |
+ DMC_MEMCONTROL_BL_8 |
+ DMC_MEMCONTROL_PZQ_DISABLE |
+ DMC_MEMCONTROL_MRR_BYTE_7_0,
+ .memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
+ DMC_MEMCONFIGx_CHIP_COL_10 |
+ DMC_MEMCONFIGx_CHIP_ROW_15 |
+ DMC_MEMCONFIGx_CHIP_BANK_8,
+ .membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
+ .membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
+ .prechconfig_tp_cnt = 0xff,
+ .dpwrdn_cyc = 0xff,
+ .dsref_cyc = 0xffff,
+ .concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
+ DMC_CONCONTROL_TIMEOUT_LEVEL0 |
+ DMC_CONCONTROL_RD_FETCH_DISABLE |
+ DMC_CONCONTROL_EMPTY_DISABLE |
+ DMC_CONCONTROL_AREF_EN_DISABLE |
+ DMC_CONCONTROL_IO_PD_CON_DISABLE,
+ .dmc_channels = 2,
+ .chips_per_channel = 2,
+ .chips_to_configure = 1,
+ .send_zq_init = 1,
+ .impedance = IMP_OUTPUT_DRV_30_OHM,
+ .gate_leveling_enable = 0,
+ }, {
+ .mem_manuf = MEM_MANUF_SAMSUNG,
+ .mem_type = DDR_MODE_DDR3,
+ .frequency_mhz = 800,
+ .mpll_mdiv = 0xc8,
+ .mpll_pdiv = 0x3,
+ .mpll_sdiv = 0x0,
+ .cpll_mdiv = 0xde,
+ .cpll_pdiv = 0x4,
+ .cpll_sdiv = 0x2,
+ .gpll_mdiv = 0x215,
+ .gpll_pdiv = 0xc,
+ .gpll_sdiv = 0x1,
+ .epll_mdiv = 0x60,
+ .epll_pdiv = 0x3,
+ .epll_sdiv = 0x3,
+ .vpll_mdiv = 0x96,
+ .vpll_pdiv = 0x3,
+ .vpll_sdiv = 0x2,
+
+ .bpll_mdiv = 0x64,
+ .bpll_pdiv = 0x3,
+ .bpll_sdiv = 0x0,
+ .pclk_cdrex_ratio = 0x5,
+ .direct_cmd_msr = {
+ 0x00020018, 0x00030000, 0x00010000, 0x00000d70
+ },
+ .timing_ref = 0x000000bb,
+ .timing_row = 0x8c36650e,
+ .timing_data = 0x3630580b,
+ .timing_power = 0x41000a44,
+ .phy0_dqs = 0x08080808,
+ .phy1_dqs = 0x08080808,
+ .phy0_dq = 0x08080808,
+ .phy1_dq = 0x08080808,
+ .phy0_tFS = 0x8,
+ .phy1_tFS = 0x8,
+ .phy0_pulld_dqs = 0xf,
+ .phy1_pulld_dqs = 0xf,
+
+ .lpddr3_ctrl_phy_reset = 0x1,
+ .ctrl_start_point = 0x10,
+ .ctrl_inc = 0x10,
+ .ctrl_start = 0x1,
+ .ctrl_dll_on = 0x1,
+ .ctrl_ref = 0x8,
+
+ .ctrl_force = 0x1a,
+ .ctrl_rdlat = 0x0b,
+ .ctrl_bstlen = 0x08,
+
+ .fp_resync = 0x8,
+ .iv_size = 0x7,
+ .dfi_init_start = 1,
+ .aref_en = 1,
+
+ .rd_fetch = 0x3,
+
+ .zq_mode_dds = 0x5,
+ .zq_mode_term = 0x1,
+ .zq_mode_noterm = 1,
+
+ /*
+ * Dynamic Clock: Always Running
+ * Memory Burst length: 8
+ * Number of chips: 1
+ * Memory Bus width: 32 bit
+ * Memory Type: DDR3
+ * Additional Latancy for PLL: 0 Cycle
+ */
+ .memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
+ DMC_MEMCONTROL_DPWRDN_DISABLE |
+ DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
+ DMC_MEMCONTROL_TP_DISABLE |
+ DMC_MEMCONTROL_DSREF_ENABLE |
+ DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
+ DMC_MEMCONTROL_MEM_TYPE_DDR3 |
+ DMC_MEMCONTROL_MEM_WIDTH_32BIT |
+ DMC_MEMCONTROL_NUM_CHIP_1 |
+ DMC_MEMCONTROL_BL_8 |
+ DMC_MEMCONTROL_PZQ_DISABLE |
+ DMC_MEMCONTROL_MRR_BYTE_7_0,
+ .memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
+ DMC_MEMCONFIGx_CHIP_COL_10 |
+ DMC_MEMCONFIGx_CHIP_ROW_15 |
+ DMC_MEMCONFIGx_CHIP_BANK_8,
+ .membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
+ .membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
+ .prechconfig_tp_cnt = 0xff,
+ .dpwrdn_cyc = 0xff,
+ .dsref_cyc = 0xffff,
+ .concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
+ DMC_CONCONTROL_TIMEOUT_LEVEL0 |
+ DMC_CONCONTROL_RD_FETCH_DISABLE |
+ DMC_CONCONTROL_EMPTY_DISABLE |
+ DMC_CONCONTROL_AREF_EN_DISABLE |
+ DMC_CONCONTROL_IO_PD_CON_DISABLE,
+ .dmc_channels = 2,
+ .chips_per_channel = 2,
+ .chips_to_configure = 1,
+ .send_zq_init = 1,
+ .impedance = IMP_OUTPUT_DRV_40_OHM,
+ .gate_leveling_enable = 1,
+ }
+};
+
+/**
+ * Get the required memory type and speed (SPL version).
+ *
+ * In SPL we have no device tree, so we use the machine parameters
+ *
+ * @param mem_type Returns memory type
+ * @param frequency_mhz Returns memory speed in MHz
+ * @param arm_freq Returns ARM clock speed in MHz
+ * @param mem_manuf Return Memory Manufacturer name
+ * @return 0 if all ok
+ */
+static int clock_get_mem_selection(enum ddr_mode *mem_type,
+ unsigned *frequency_mhz, unsigned *arm_freq,
+ enum mem_manuf *mem_manuf)
{
- struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+ struct spl_machine_param *params;
- /*
- * MUX_APLL_SEL[0]: FINPLL = 0
- * MUX_CPU_SEL[6]: MOUTAPLL = 0
- * MUX_HPM_SEL[20]: MOUTAPLL = 0
- */
- writel(0x0, &clk->src_cpu);
+ params = spl_get_machine_params();
+ *mem_type = params->mem_type;
+ *frequency_mhz = params->frequency_mhz;
+ *arm_freq = params->arm_freq_mhz;
+ *mem_manuf = params->mem_manuf;
- /* MUX_MPLL_SEL[8]: FINPLL = 0 */
- writel(0x0, &clk->src_core1);
+ return 0;
+}
- /*
- * VPLLSRC_SEL[0]: FINPLL = 0
- * MUX_{CPLL[8]}|{EPLL[12]}|{VPLL[16]}_SEL: FINPLL = 0
- */
- writel(0x0, &clk->src_top2);
+/* Get the ratios for setting ARM clock */
+struct arm_clk_ratios *get_arm_ratios(void)
+{
+ struct arm_clk_ratios *arm_ratio;
+ enum ddr_mode mem_type;
+ enum mem_manuf mem_manuf;
+ unsigned frequency_mhz, arm_freq;
+ int i;
+
+ if (clock_get_mem_selection(&mem_type, &frequency_mhz,
+ &arm_freq, &mem_manuf))
+ ;
+ for (i = 0, arm_ratio = arm_clk_ratios; i < ARRAY_SIZE(arm_clk_ratios);
+ i++, arm_ratio++) {
+ if (arm_ratio->arm_freq_mhz == arm_freq)
+ return arm_ratio;
+ }
+
+ /* will hang if failed to find clock ratio */
+ while (1)
+ ;
+
+ return NULL;
+}
- /* MUX_BPLL_SEL[0]: FINPLL = 0 */
- writel(0x0, &clk->src_cdrex);
+struct mem_timings *clock_get_mem_timings(void)
+{
+ struct mem_timings *mem;
+ enum ddr_mode mem_type;
+ enum mem_manuf mem_manuf;
+ unsigned frequency_mhz, arm_freq;
+ int i;
+
+ if (!clock_get_mem_selection(&mem_type, &frequency_mhz,
+ &arm_freq, &mem_manuf)) {
+ for (i = 0, mem = mem_timings; i < ARRAY_SIZE(mem_timings);
+ i++, mem++) {
+ if (mem->mem_type == mem_type &&
+ mem->frequency_mhz == frequency_mhz &&
+ mem->mem_manuf == mem_manuf)
+ return mem;
+ }
+ }
+
+ /* will hang if failed to find memory timings */
+ while (1)
+ ;
+
+ return NULL;
+}
- /* MUX_ACLK_* Clock Selection */
- writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
+void system_clock_init()
+{
+ struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+ struct mem_timings *mem;
+ struct arm_clk_ratios *arm_clk_ratio;
+ u32 val, tmp;
+
+ mem = clock_get_mem_timings();
+ arm_clk_ratio = get_arm_ratios();
+
+ clrbits_le32(&clk->src_cpu, MUX_APLL_SEL_MASK);
+ do {
+ val = readl(&clk->mux_stat_cpu);
+ } while ((val | MUX_APLL_SEL_MASK) != val);
+
+ clrbits_le32(&clk->src_core1, MUX_MPLL_SEL_MASK);
+ do {
+ val = readl(&clk->mux_stat_core1);
+ } while ((val | MUX_MPLL_SEL_MASK) != val);
+
+ clrbits_le32(&clk->src_core1, MUX_CPLL_SEL_MASK);
+ clrbits_le32(&clk->src_core1, MUX_EPLL_SEL_MASK);
+ clrbits_le32(&clk->src_core1, MUX_VPLL_SEL_MASK);
+ clrbits_le32(&clk->src_core1, MUX_GPLL_SEL_MASK);
+ tmp = MUX_CPLL_SEL_MASK | MUX_EPLL_SEL_MASK | MUX_VPLL_SEL_MASK
+ | MUX_GPLL_SEL_MASK;
+ do {
+ val = readl(&clk->mux_stat_top2);
+ } while ((val | tmp) != val);
+
+ clrbits_le32(&clk->src_cdrex, MUX_BPLL_SEL_MASK);
+ do {
+ val = readl(&clk->mux_stat_cdrex);
+ } while ((val | MUX_BPLL_SEL_MASK) != val);
- /* MUX_ACLK_* Clock Selection */
- writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
+ /* PLL locktime */
+ writel(APLL_LOCK_VAL, &clk->apll_lock);
- /* MUX_ACLK_* Clock Selection */
- writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
+ writel(MPLL_LOCK_VAL, &clk->mpll_lock);
- /* MUX_PWI_SEL[19:16]: SCLKMPLL = 6 */
- writel(CLK_SRC_CORE0_VAL, &clk->src_core0);
+ writel(BPLL_LOCK_VAL, &clk->bpll_lock);
- /* MUX_ATCLK_LEX[0]: ACLK_200 = 0 */
- writel(CLK_SRC_LEX_VAL, &clk->src_lex);
+ writel(CPLL_LOCK_VAL, &clk->cpll_lock);
- /* UART [0-5]: SCLKMPLL = 6 */
- writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
+ writel(GPLL_LOCK_VAL, &clk->gpll_lock);
- /* Set Clock Ratios */
- writel(CLK_DIV_CPU0_VAL, &clk->div_cpu0);
+ writel(EPLL_LOCK_VAL, &clk->epll_lock);
+
+ writel(VPLL_LOCK_VAL, &clk->vpll_lock);
+
+ writel(CLK_REG_DISABLE, &clk->pll_div2_sel);
+
+ writel(MUX_HPM_SEL_MASK, &clk->src_cpu);
+ do {
+ val = readl(&clk->mux_stat_cpu);
+ } while ((val | HPM_SEL_SCLK_MPLL) != val);
+
+ val = arm_clk_ratio->arm2_ratio << 28
+ | arm_clk_ratio->apll_ratio << 24
+ | arm_clk_ratio->pclk_dbg_ratio << 20
+ | arm_clk_ratio->atb_ratio << 16
+ | arm_clk_ratio->periph_ratio << 12
+ | arm_clk_ratio->acp_ratio << 8
+ | arm_clk_ratio->cpud_ratio << 4
+ | arm_clk_ratio->arm_ratio;
+ writel(val, &clk->div_cpu0);
+ do {
+ val = readl(&clk->div_stat_cpu0);
+ } while (0 != val);
- /* Set COPY and HPM Ratio */
writel(CLK_DIV_CPU1_VAL, &clk->div_cpu1);
+ do {
+ val = readl(&clk->div_stat_cpu1);
+ } while (0 != val);
- /* CORED_RATIO, COREP_RATIO */
- writel(CLK_DIV_CORE0_VAL, &clk->div_core0);
+ /* Set APLL */
+ writel(APLL_CON1_VAL, &clk->apll_con1);
+ val = set_pll(arm_clk_ratio->apll_mdiv, arm_clk_ratio->apll_pdiv,
+ arm_clk_ratio->apll_sdiv);
+ writel(val, &clk->apll_con0);
+ while (readl(&clk->apll_con0) & APLL_CON0_LOCKED)
+ ;
- /* PWI_RATIO[11:8], DVSEM_RATIO[22:16], DPM_RATIO[24:20] */
- writel(CLK_DIV_CORE1_VAL, &clk->div_core1);
+ /* Set MPLL */
+ writel(MPLL_CON1_VAL, &clk->mpll_con1);
+ val = set_pll(mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv);
+ writel(val, &clk->mpll_con0);
+ while (readl(&clk->mpll_con0) & MPLL_CON0_LOCKED)
+ ;
- /* ACLK_*_RATIO */
- writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
+ /* Set BPLL */
+ writel(BPLL_CON1_VAL, &clk->bpll_con1);
+ val = set_pll(mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv);
+ writel(val, &clk->bpll_con0);
+ while (readl(&clk->bpll_con0) & BPLL_CON0_LOCKED)
+ ;
- /* ACLK_*_RATIO */
- writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
+ /* Set CPLL */
+ writel(CPLL_CON1_VAL, &clk->cpll_con1);
+ val = set_pll(mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv);
+ writel(val, &clk->cpll_con0);
+ while (readl(&clk->cpll_con0) & CPLL_CON0_LOCKED)
+ ;
+
+ /* Set GPLL */
+ writel(GPLL_CON1_VAL, &clk->gpll_con1);
+ val = set_pll(mem->gpll_mdiv, mem->gpll_pdiv, mem->gpll_sdiv);
+ writel(val, &clk->gpll_con0);
+ while (readl(&clk->gpll_con0) & GPLL_CON0_LOCKED)
+ ;
- /* CDREX Ratio */
- writel(CLK_DIV_CDREX_INIT_VAL, &clk->div_cdrex);
+ /* Set EPLL */
+ writel(EPLL_CON2_VAL, &clk->epll_con2);
+ writel(EPLL_CON1_VAL, &clk->epll_con1);
+ val = set_pll(mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv);
+ writel(val, &clk->epll_con0);
+ while (readl(&clk->epll_con0) & EPLL_CON0_LOCKED)
+ ;
- /* MCLK_EFPHY_RATIO[3:0] */
- writel(CLK_DIV_CDREX2_VAL, &clk->div_cdrex2);
+ /* Set VPLL */
+ writel(VPLL_CON2_VAL, &clk->vpll_con2);
+ writel(VPLL_CON1_VAL, &clk->vpll_con1);
+ val = set_pll(mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv);
+ writel(val, &clk->vpll_con0);
+ while (readl(&clk->vpll_con0) & VPLL_CON0_LOCKED)
+ ;
- /* {PCLK[4:6]|ATCLK[10:8]}_RATIO */
- writel(CLK_DIV_LEX_VAL, &clk->div_lex);
+ writel(CLK_SRC_CORE0_VAL, &clk->src_core0);
+ writel(CLK_DIV_CORE0_VAL, &clk->div_core0);
+ while (readl(&clk->div_stat_core0) != 0)
+ ;
- /* PCLK_R0X_RATIO[3:0] */
- writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
+ writel(CLK_DIV_CORE1_VAL, &clk->div_core1);
+ while (readl(&clk->div_stat_core1) != 0)
+ ;
- /* PCLK_R1X_RATIO[3:0] */
- writel(CLK_DIV_R1X_VAL, &clk->div_r1x);
+ writel(CLK_DIV_SYSRGT_VAL, &clk->div_sysrgt);
+ while (readl(&clk->div_stat_sysrgt) != 0)
+ ;
- /* SATA[24]: SCLKMPLL=0, MMC[0-4]: SCLKMPLL = 6 */
- writel(CLK_SRC_FSYS_VAL, &clk->src_fsys);
+ writel(CLK_DIV_ACP_VAL, &clk->div_acp);
+ while (readl(&clk->div_stat_acp) != 0)
+ ;
- /* UART[0-4] */
- writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
+ writel(CLK_DIV_SYSLFT_VAL, &clk->div_syslft);
+ while (readl(&clk->div_stat_syslft) != 0)
+ ;
- /* PWM_RATIO[3:0] */
- writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
+ writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
+ writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
+ writel(TOP2_VAL, &clk->src_top2);
+ writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
- /* SATA_RATIO, USB_DRD_RATIO */
- writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
+ writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
+ while (readl(&clk->div_stat_top0))
+ ;
- /* MMC[0-1] */
- writel(CLK_DIV_FSYS1_VAL, &clk->div_fsys1);
+ writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
+ while (readl(&clk->div_stat_top1))
+ ;
- /* MMC[2-3] */
- writel(CLK_DIV_FSYS2_VAL, &clk->div_fsys2);
+ writel(CLK_SRC_LEX_VAL, &clk->src_lex);
+ while (1) {
+ val = readl(&clk->mux_stat_lex);
+ if (val == (val | 1))
+ break;
+ }
- /* MMC[4] */
- writel(CLK_DIV_FSYS3_VAL, &clk->div_fsys3);
+ writel(CLK_DIV_LEX_VAL, &clk->div_lex);
+ while (readl(&clk->div_stat_lex))
+ ;
- /* ACLK|PLCK_ACP_RATIO */
- writel(CLK_DIV_ACP_VAL, &clk->div_acp);
+ writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
+ while (readl(&clk->div_stat_r0x))
+ ;
- /* ISPDIV0_RATIO, ISPDIV1_RATIO */
- writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
+ writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
+ while (readl(&clk->div_stat_r0x))
+ ;
- /* MCUISPDIV0_RATIO, MCUISPDIV1_RATIO */
- writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
+ writel(CLK_DIV_R1X_VAL, &clk->div_r1x);
+ while (readl(&clk->div_stat_r1x))
+ ;
- /* MPWMDIV_RATIO */
- writel(CLK_DIV_ISP2_VAL, &clk->div_isp2);
+ writel(CLK_REG_DISABLE, &clk->src_cdrex);
- /* PLL locktime */
- writel(APLL_LOCK_VAL, &clk->apll_lock);
+ writel(CLK_DIV_CDREX_VAL, &clk->div_cdrex);
+ while (readl(&clk->div_stat_cdrex))
+ ;
- writel(MPLL_LOCK_VAL, &clk->mpll_lock);
+ val = readl(&clk->src_cpu);
+ val |= CLK_SRC_CPU_VAL;
+ writel(val, &clk->src_cpu);
- writel(BPLL_LOCK_VAL, &clk->bpll_lock);
+ val = readl(&clk->src_top2);
+ val |= CLK_SRC_TOP2_VAL;
+ writel(val, &clk->src_top2);
- writel(CPLL_LOCK_VAL, &clk->cpll_lock);
+ val = readl(&clk->src_core1);
+ val |= CLK_SRC_CORE1_VAL;
+ writel(val, &clk->src_core1);
- writel(EPLL_LOCK_VAL, &clk->epll_lock);
+ writel(CLK_SRC_FSYS0_VAL, &clk->src_fsys);
+ writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
+ while (readl(&clk->div_stat_fsys0))
+ ;
+
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_cpu);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_core);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_acp);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_top);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_lex);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_r0x);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_r1x);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_cdrex);
- writel(VPLL_LOCK_VAL, &clk->vpll_lock);
+ writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
+ writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
- sdelay(0x10000);
+ writel(CLK_SRC_PERIC1_VAL, &clk->src_peric1);
+ writel(CLK_DIV_PERIC1_VAL, &clk->div_peric1);
+ writel(CLK_DIV_PERIC2_VAL, &clk->div_peric2);
+ writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
- /* Set APLL */
- writel(APLL_CON1_VAL, &clk->apll_con1);
- writel(APLL_CON0_VAL, &clk->apll_con0);
- sdelay(0x30000);
+ writel(SCLK_SRC_ISP_VAL, &clk->sclk_src_isp);
+ writel(SCLK_DIV_ISP_VAL, &clk->sclk_div_isp);
+ writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
+ writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
+ writel(CLK_DIV_ISP2_VAL, &clk->div_isp2);
- /* Set MPLL */
- writel(MPLL_CON1_VAL, &clk->mpll_con1);
- writel(MPLL_CON0_VAL, &clk->mpll_con0);
- sdelay(0x30000);
- writel(BPLL_CON1_VAL, &clk->bpll_con1);
- writel(BPLL_CON0_VAL, &clk->bpll_con0);
- sdelay(0x30000);
+ /* FIMD1 SRC CLK SELECTION */
+ writel(CLK_SRC_DISP1_0_VAL, &clk->src_disp1_0);
- /* Set CPLL */
- writel(CPLL_CON1_VAL, &clk->cpll_con1);
- writel(CPLL_CON0_VAL, &clk->cpll_con0);
- sdelay(0x30000);
+ val = MMC2_PRE_RATIO_VAL << MMC2_PRE_RATIO_OFFSET
+ | MMC2_RATIO_VAL << MMC2_RATIO_OFFSET
+ | MMC3_PRE_RATIO_VAL << MMC3_PRE_RATIO_OFFSET
+ | MMC3_RATIO_VAL << MMC3_RATIO_OFFSET;
+ writel(val, &clk->div_fsys2);
+}
- /* Set EPLL */
- writel(EPLL_CON2_VAL, &clk->epll_con2);
- writel(EPLL_CON1_VAL, &clk->epll_con1);
- writel(EPLL_CON0_VAL, &clk->epll_con0);
- sdelay(0x30000);
+void clock_init_dp_clock(void)
+{
+ struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
- /* Set VPLL */
- writel(VPLL_CON2_VAL, &clk->vpll_con2);
- writel(VPLL_CON1_VAL, &clk->vpll_con1);
- writel(VPLL_CON0_VAL, &clk->vpll_con0);
- sdelay(0x30000);
+ /* DP clock enable */
+ setbits_le32(&clk->gate_ip_disp1, CLK_GATE_DP1_ALLOW);
- /* Set MPLL */
- /* After Initiallising th PLL select the sources accordingly */
- /* MUX_APLL_SEL[0]: MOUTAPLLFOUT = 1 */
- writel(CLK_SRC_CPU_VAL, &clk->src_cpu);
-
- /* MUX_MPLL_SEL[8]: MOUTMPLLFOUT = 1 */
- writel(CLK_SRC_CORE1_VAL, &clk->src_core1);
-
- /* MUX_BPLL_SEL[0]: FOUTBPLL = 1*/
- writel(CLK_SRC_CDREX_INIT_VAL, &clk->src_cdrex);
-
- /*
- * VPLLSRC_SEL[0]: FINPLL = 0
- * MUX_{CPLL[8]}|{EPLL[12]}|{VPLL[16]}_SEL: MOUT{CPLL|EPLL|VPLL} = 1
- * MUX_{MPLL[20]}|{BPLL[24]}_USER_SEL: FOUT{MPLL|BPLL} = 1
- */
- writel(CLK_SRC_TOP2_VAL, &clk->src_top2);
+ /* We run DP at 267 Mhz */
+ setbits_le32(&clk->div_disp1_0, CLK_DIV_DISP1_0_FIMD1);
}
diff --git a/board/samsung/smdk5250/clock_init.h b/board/samsung/smdk5250/clock_init.h
new file mode 100644
index 0000000..f751bcb
--- /dev/null
+++ b/board/samsung/smdk5250/clock_init.h
@@ -0,0 +1,149 @@
+/*
+ * Clock initialization routines
+ *
+ * Copyright (c) 2011 The Chromium OS Authors.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __EXYNOS_CLOCK_INIT_H
+#define __EXYNOS_CLOCK_INIT_H
+
+enum {
+ MEM_TIMINGS_MSR_COUNT = 4,
+};
+
+/* These are the ratio's for configuring ARM clock */
+struct arm_clk_ratios {
+ unsigned arm_freq_mhz; /* Frequency of ARM core in MHz */
+
+ unsigned apll_mdiv;
+ unsigned apll_pdiv;
+ unsigned apll_sdiv;
+
+ unsigned arm2_ratio;
+ unsigned apll_ratio;
+ unsigned pclk_dbg_ratio;
+ unsigned atb_ratio;
+ unsigned periph_ratio;
+ unsigned acp_ratio;
+ unsigned cpud_ratio;
+ unsigned arm_ratio;
+};
+
+/* These are the memory timings for a particular memory type and speed */
+struct mem_timings {
+ enum mem_manuf mem_manuf; /* Memory manufacturer */
+ enum ddr_mode mem_type; /* Memory type */
+ unsigned frequency_mhz; /* Frequency of memory in MHz */
+
+ /* Here follow the timing parameters for the selected memory */
+ unsigned apll_mdiv;
+ unsigned apll_pdiv;
+ unsigned apll_sdiv;
+ unsigned mpll_mdiv;
+ unsigned mpll_pdiv;
+ unsigned mpll_sdiv;
+ unsigned cpll_mdiv;
+ unsigned cpll_pdiv;
+ unsigned cpll_sdiv;
+ unsigned gpll_mdiv;
+ unsigned gpll_pdiv;
+ unsigned gpll_sdiv;
+ unsigned epll_mdiv;
+ unsigned epll_pdiv;
+ unsigned epll_sdiv;
+ unsigned vpll_mdiv;
+ unsigned vpll_pdiv;
+ unsigned vpll_sdiv;
+ unsigned bpll_mdiv;
+ unsigned bpll_pdiv;
+ unsigned bpll_sdiv;
+ unsigned pclk_cdrex_ratio;
+ unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
+
+ unsigned timing_ref;
+ unsigned timing_row;
+ unsigned timing_data;
+ unsigned timing_power;
+
+ /* DQS, DQ, DEBUG offsets */
+ unsigned phy0_dqs;
+ unsigned phy1_dqs;
+ unsigned phy0_dq;
+ unsigned phy1_dq;
+ unsigned phy0_tFS;
+ unsigned phy1_tFS;
+ unsigned phy0_pulld_dqs;
+ unsigned phy1_pulld_dqs;
+
+ unsigned lpddr3_ctrl_phy_reset;
+ unsigned ctrl_start_point;
+ unsigned ctrl_inc;
+ unsigned ctrl_start;
+ unsigned ctrl_dll_on;
+ unsigned ctrl_ref;
+
+ unsigned ctrl_force;
+ unsigned ctrl_rdlat;
+ unsigned ctrl_bstlen;
+
+ unsigned fp_resync;
+ unsigned iv_size;
+ unsigned dfi_init_start;
+ unsigned aref_en;
+
+ unsigned rd_fetch;
+
+ unsigned zq_mode_dds;
+ unsigned zq_mode_term;
+ unsigned zq_mode_noterm; /* 1 to allow termination disable */
+
+ unsigned memcontrol;
+ unsigned memconfig;
+
+ unsigned membaseconfig0;
+ unsigned membaseconfig1;
+ unsigned prechconfig_tp_cnt;
+ unsigned dpwrdn_cyc;
+ unsigned dsref_cyc;
+ unsigned concontrol;
+ /* Channel and Chip Selection */
+ uint8_t dmc_channels; /* number of memory channels */
+ uint8_t chips_per_channel; /* number of chips per channel */
+ uint8_t chips_to_configure; /* number of chips to configure */
+ uint8_t send_zq_init; /* 1 to send this command */
+ unsigned impedance; /* drive strength impedeance */
+ uint8_t gate_leveling_enable; /* check gate leveling is enabled */
+};
+
+/**
+ * Get the correct memory timings for our selected memory type and speed.
+ *
+ * This function can be called from SPL or the main U-Boot.
+ *
+ * @return pointer to the memory timings that we should use
+ */
+struct mem_timings *clock_get_mem_timings(void);
+
+/*
+ * Initialize clock for the device
+ */
+void system_clock_init(void);
+#endif
diff --git a/board/samsung/smdk5250/setup.h b/board/samsung/smdk5250/setup.h
index 1276fd3..bae0faf 100644
--- a/board/samsung/smdk5250/setup.h
+++ b/board/samsung/smdk5250/setup.h
@@ -1,5 +1,5 @@
/*
- * Machine Specific Values for SMDK5250 board based on S5PC520
+ * Machine Specific Values for SMDK5250 board based on EXYNOS5
*
* Copyright (C) 2012 Samsung Electronics
*
@@ -26,12 +26,6 @@
#define _SMDK5250_SETUP_H
#include <config.h>
-#include <version.h>
-#include <asm/arch/cpu.h>
-
-/* GPIO Offsets for UART: GPIO Contol Register */
-#define EXYNOS5_GPIO_A0_CON_OFFSET 0x0
-#define EXYNOS5_GPIO_A1_CON_OFFSET 0x20
/* TZPC : Register Offsets */
#define TZPC0_BASE 0x10100000
@@ -45,295 +39,423 @@
#define TZPC8_BASE 0x10180000
#define TZPC9_BASE 0x10190000
-/* CLK_SRC_CPU */
-/* 0 = MOUTAPLL, 1 = SCLKMPLL */
-#define MUX_HPM_SEL 0
-#define MUX_CPU_SEL 0
-#define MUX_APLL_SEL 1
-#define CLK_SRC_CPU_VAL ((MUX_HPM_SEL << 20) \
- | (MUX_CPU_SEL << 16) \
- | (MUX_APLL_SEL))
-
-/* CLK_DIV_CPU0 */
-#define ARM2_RATIO 0x0
-#define APLL_RATIO 0x1
-#define PCLK_DBG_RATIO 0x1
-#define ATB_RATIO 0x4
-#define PERIPH_RATIO 0x7
-#define ACP_RATIO 0x7
-#define CPUD_RATIO 0x2
-#define ARM_RATIO 0x0
-#define CLK_DIV_CPU0_VAL ((ARM2_RATIO << 28) \
- | (APLL_RATIO << 24) \
- | (PCLK_DBG_RATIO << 20) \
- | (ATB_RATIO << 16) \
- | (PERIPH_RATIO << 12) \
- | (ACP_RATIO << 8) \
- | (CPUD_RATIO << 4) \
- | (ARM_RATIO))
-
-/* CLK_DIV_CPU1 */
-#define HPM_RATIO 0x4
-#define COPY_RATIO 0x0
-#define CLK_DIV_CPU1_VAL ((HPM_RATIO << 4) \
- | (COPY_RATIO))
-
-#define APLL_MDIV 0x7D
-#define APLL_PDIV 0x3
-#define APLL_SDIV 0x0
-
-#define MPLL_MDIV 0x64
-#define MPLL_PDIV 0x3
-#define MPLL_SDIV 0x0
-
-#define CPLL_MDIV 0x96
-#define CPLL_PDIV 0x4
-#define CPLL_SDIV 0x0
-
-/* APLL_CON1 */
+/* APLL_CON1 */
#define APLL_CON1_VAL (0x00203800)
-/* MPLL_CON1 */
-#define MPLL_CON1_VAL (0x00203800)
+/* MPLL_CON1 */
+#define MPLL_CON1_VAL (0x00203800)
-/* CPLL_CON1 */
+/* CPLL_CON1 */
#define CPLL_CON1_VAL (0x00203800)
-#define EPLL_MDIV 0x60
-#define EPLL_PDIV 0x3
-#define EPLL_SDIV 0x3
+/* GPLL_CON1 */
+#define GPLL_CON1_VAL (0x00203800)
+/* EPLL_CON1, CON2 */
#define EPLL_CON1_VAL 0x00000000
#define EPLL_CON2_VAL 0x00000080
-#define VPLL_MDIV 0x96
-#define VPLL_PDIV 0x3
-#define VPLL_SDIV 0x2
-
+/* VPLL_CON1, CON2 */
#define VPLL_CON1_VAL 0x00000000
#define VPLL_CON2_VAL 0x00000080
-#define BPLL_MDIV 0x215
-#define BPLL_PDIV 0xC
-#define BPLL_SDIV 0x1
-
+/* BPLL_CON1 */
#define BPLL_CON1_VAL 0x00203800
/* Set PLL */
#define set_pll(mdiv, pdiv, sdiv) (1<<31 | mdiv<<16 | pdiv<<8 | sdiv)
-#define APLL_CON0_VAL set_pll(APLL_MDIV, APLL_PDIV, APLL_SDIV)
-#define MPLL_CON0_VAL set_pll(MPLL_MDIV, MPLL_PDIV, MPLL_SDIV)
-#define CPLL_CON0_VAL set_pll(CPLL_MDIV, CPLL_PDIV, CPLL_SDIV)
-#define EPLL_CON0_VAL set_pll(EPLL_MDIV, EPLL_PDIV, EPLL_SDIV)
-#define VPLL_CON0_VAL set_pll(VPLL_MDIV, VPLL_PDIV, VPLL_SDIV)
-#define BPLL_CON0_VAL set_pll(BPLL_MDIV, BPLL_PDIV, BPLL_SDIV)
+/* CLK_SRC_CPU */
+/* 0 = MOUTAPLL, 1 = SCLKMPLL */
+#define MUX_HPM_SEL 0
+#define MUX_CPU_SEL 0
+#define MUX_APLL_SEL 1
+
+#define CLK_SRC_CPU_VAL ((MUX_HPM_SEL << 20) \
+ | (MUX_CPU_SEL << 16) \
+ | (MUX_APLL_SEL))
+
+/* MEMCONTROL register bit fields */
+#define DMC_MEMCONTROL_CLK_STOP_DISABLE (0 << 0)
+#define DMC_MEMCONTROL_DPWRDN_DISABLE (0 << 1)
+#define DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE (0 << 2)
+#define DMC_MEMCONTROL_TP_DISABLE (0 << 4)
+#define DMC_MEMCONTROL_DSREF_DISABLE (0 << 5)
+#define DMC_MEMCONTROL_DSREF_ENABLE (1 << 5)
+#define DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(x) (x << 6)
+
+#define DMC_MEMCONTROL_MEM_TYPE_LPDDR3 (7 << 8)
+#define DMC_MEMCONTROL_MEM_TYPE_DDR3 (6 << 8)
+#define DMC_MEMCONTROL_MEM_TYPE_LPDDR2 (5 << 8)
+
+#define DMC_MEMCONTROL_MEM_WIDTH_32BIT (2 << 12)
+
+#define DMC_MEMCONTROL_NUM_CHIP_1 (0 << 16)
+#define DMC_MEMCONTROL_NUM_CHIP_2 (1 << 16)
+
+#define DMC_MEMCONTROL_BL_8 (3 << 20)
+#define DMC_MEMCONTROL_BL_4 (2 << 20)
+
+#define DMC_MEMCONTROL_PZQ_DISABLE (0 << 24)
+
+#define DMC_MEMCONTROL_MRR_BYTE_7_0 (0 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_15_8 (1 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_23_16 (2 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_31_24 (3 << 25)
+
+/* MEMCONFIG0 register bit fields */
+#define DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED (1 << 12)
+#define DMC_MEMCONFIGx_CHIP_COL_10 (3 << 8)
+#define DMC_MEMCONFIGx_CHIP_ROW_14 (2 << 4)
+#define DMC_MEMCONFIGx_CHIP_ROW_15 (3 << 4)
+#define DMC_MEMCONFIGx_CHIP_BANK_8 (3 << 0)
+
+#define DMC_MEMBASECONFIGx_CHIP_BASE(x) (x << 16)
+#define DMC_MEMBASECONFIGx_CHIP_MASK(x) (x << 0)
+#define DMC_MEMBASECONFIG_VAL(x) ( \
+ DMC_MEMBASECONFIGx_CHIP_BASE(x) | \
+ DMC_MEMBASECONFIGx_CHIP_MASK(0x780) \
+)
+
+#define DMC_MEMBASECONFIG0_VAL DMC_MEMBASECONFIG_VAL(0x40)
+#define DMC_MEMBASECONFIG1_VAL DMC_MEMBASECONFIG_VAL(0x80)
+
+#define DMC_PRECHCONFIG_VAL 0xFF000000
+#define DMC_PWRDNCONFIG_VAL 0xFFFF00FF
+
+#define DMC_CONCONTROL_RESET_VAL 0x0FFF0000
+#define DFI_INIT_START (1 << 28)
+#define EMPTY (1 << 8)
+#define AREF_EN (1 << 5)
+
+#define DFI_INIT_COMPLETE_CHO (1 << 2)
+#define DFI_INIT_COMPLETE_CH1 (1 << 3)
+
+#define RDLVL_COMPLETE_CHO (1 << 14)
+#define RDLVL_COMPLETE_CH1 (1 << 15)
+
+#define CLK_STOP_EN (1 << 0)
+#define DPWRDN_EN (1 << 1)
+#define DSREF_EN (1 << 5)
+
+/* COJCONTROL register bit fields */
+#define DMC_CONCONTROL_IO_PD_CON_DISABLE (0 << 3)
+#define DMC_CONCONTROL_AREF_EN_DISABLE (0 << 5)
+#define DMC_CONCONTROL_EMPTY_DISABLE (0 << 8)
+#define DMC_CONCONTROL_EMPTY_ENABLE (1 << 8)
+#define DMC_CONCONTROL_RD_FETCH_DISABLE (0x0 << 12)
+#define DMC_CONCONTROL_TIMEOUT_LEVEL0 (0xFFF << 16)
+#define DMC_CONCONTROL_DFI_INIT_START_DISABLE (0 << 28)
+
+/* CLK_DIV_CPU0_VAL */
+#define CLK_DIV_CPU0_VAL ((ARM2_RATIO << 28) \
+ | (APLL_RATIO << 24) \
+ | (PCLK_DBG_RATIO << 20) \
+ | (ATB_RATIO << 16) \
+ | (PERIPH_RATIO << 12) \
+ | (ACP_RATIO << 8) \
+ | (CPUD_RATIO << 4) \
+ | (ARM_RATIO))
+
+
+/* CLK_FSYS */
+#define CLK_SRC_FSYS0_VAL 0x66666
+#define CLK_DIV_FSYS0_VAL 0x0BB00000
+
+/* CLK_DIV_CPU1 */
+#define HPM_RATIO 0x2
+#define COPY_RATIO 0x0
+
+/* CLK_DIV_CPU1 = 0x00000003 */
+#define CLK_DIV_CPU1_VAL ((HPM_RATIO << 4) \
+ | (COPY_RATIO))
/* CLK_SRC_CORE0 */
-#define CLK_SRC_CORE0_VAL 0x00060000
+#define CLK_SRC_CORE0_VAL 0x00000000
/* CLK_SRC_CORE1 */
-#define CLK_SRC_CORE1_VAL 0x100
+#define CLK_SRC_CORE1_VAL 0x100
/* CLK_DIV_CORE0 */
-#define CLK_DIV_CORE0_VAL 0x120000
+#define CLK_DIV_CORE0_VAL 0x00120000
/* CLK_DIV_CORE1 */
-#define CLK_DIV_CORE1_VAL 0x07070700
+#define CLK_DIV_CORE1_VAL 0x07070700
+
+/* CLK_DIV_SYSRGT */
+#define CLK_DIV_SYSRGT_VAL 0x00000111
+
+/* CLK_DIV_ACP */
+#define CLK_DIV_ACP_VAL 0x12
+
+/* CLK_DIV_SYSLFT */
+#define CLK_DIV_SYSLFT_VAL 0x00000311
/* CLK_SRC_CDREX */
-#define CLK_SRC_CDREX_INIT_VAL 0x1
-#define CLK_SRC_CDREX_VAL 0x111
+#define CLK_SRC_CDREX_VAL 0x1
/* CLK_DIV_CDREX */
-#define CLK_DIV_CDREX_INIT_VAL 0x71771111
-
-#define MCLK_CDREX2_RATIO 0x0
-#define ACLK_EFCON_RATIO 0x1
-#define MCLK_DPHY_RATIO 0x0
-#define MCLK_CDREX_RATIO 0x0
+#define MCLK_CDREX2_RATIO 0x0
+#define ACLK_EFCON_RATIO 0x1
+#define MCLK_DPHY_RATIO 0x1
+#define MCLK_CDREX_RATIO 0x1
#define ACLK_C2C_200_RATIO 0x1
#define C2C_CLK_400_RATIO 0x1
-#define PCLK_CDREX_RATIO 0x3
+#define PCLK_CDREX_RATIO 0x1
#define ACLK_CDREX_RATIO 0x1
-#define CLK_DIV_CDREX_VAL ((MCLK_DPHY_RATIO << 20) \
- | (MCLK_CDREX_RATIO << 16) \
- | (ACLK_C2C_200_RATIO << 12) \
- | (C2C_CLK_400_RATIO << 8) \
- | (PCLK_CDREX_RATIO << 4) \
- | (ACLK_CDREX_RATIO))
-#define MCLK_EFPHY_RATIO 0x4
-#define CLK_DIV_CDREX2_VAL MCLK_EFPHY_RATIO
+#define CLK_DIV_CDREX_VAL ((MCLK_DPHY_RATIO << 24) \
+ | (C2C_CLK_400_RATIO << 6) \
+ | (PCLK_CDREX_RATIO << 4) \
+ | (ACLK_CDREX_RATIO))
-/* CLK_DIV_ACP */
-#define CLK_DIV_ACP_VAL 0x12
-
-/* CLK_SRC_TOP0 */
-#define MUX_ACLK_300_GSCL_SEL 0x1
-#define MUX_ACLK_300_GSCL_MID_SEL 0x0
-#define MUX_ACLK_400_SEL 0x0
-#define MUX_ACLK_333_SEL 0x0
-#define MUX_ACLK_300_DISP1_SEL 0x1
-#define MUX_ACLK_300_DISP1_MID_SEL 0x0
-#define MUX_ACLK_200_SEL 0x0
-#define MUX_ACLK_166_SEL 0x0
-#define CLK_SRC_TOP0_VAL ((MUX_ACLK_300_GSCL_SEL << 25) \
- | (MUX_ACLK_300_GSCL_MID_SEL << 24) \
- | (MUX_ACLK_400_SEL << 20) \
- | (MUX_ACLK_333_SEL << 16) \
- | (MUX_ACLK_300_DISP1_SEL << 15) \
+/* CLK_SRC_TOP0 */
+#define MUX_ACLK_300_GSCL_SEL 0x0
+#define MUX_ACLK_300_GSCL_MID_SEL 0x0
+#define MUX_ACLK_400_G3D_MID_SEL 0x0
+#define MUX_ACLK_333_SEL 0x0
+#define MUX_ACLK_300_DISP1_SEL 0x0
+#define MUX_ACLK_300_DISP1_MID_SEL 0x0
+#define MUX_ACLK_200_SEL 0x0
+#define MUX_ACLK_166_SEL 0x0
+#define CLK_SRC_TOP0_VAL ((MUX_ACLK_300_GSCL_SEL << 25) \
+ | (MUX_ACLK_300_GSCL_MID_SEL << 24) \
+ | (MUX_ACLK_400_G3D_MID_SEL << 20) \
+ | (MUX_ACLK_333_SEL << 16) \
+ | (MUX_ACLK_300_DISP1_SEL << 15) \
| (MUX_ACLK_300_DISP1_MID_SEL << 14) \
- | (MUX_ACLK_200_SEL << 12) \
+ | (MUX_ACLK_200_SEL << 12) \
| (MUX_ACLK_166_SEL << 8))
-/* CLK_SRC_TOP1 */
-#define MUX_ACLK_400_ISP_SEL 0x0
-#define MUX_ACLK_400_IOP_SEL 0x0
-#define MUX_ACLK_MIPI_HSI_TXBASE_SEL 0x0
-#define CLK_SRC_TOP1_VAL ((MUX_ACLK_400_ISP_SEL << 24) \
- |(MUX_ACLK_400_IOP_SEL << 20) \
- |(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16))
+/* CLK_SRC_TOP1 */
+#define MUX_ACLK_400_G3D_SEL 0x1
+#define MUX_ACLK_400_ISP_SEL 0x0
+#define MUX_ACLK_400_IOP_SEL 0x0
+#define MUX_ACLK_MIPI_HSI_TXBASE_SEL 0x0
+#define MUX_ACLK_300_GSCL_MID1_SEL 0x0
+#define MUX_ACLK_300_DISP1_MID1_SEL 0x0
+#define CLK_SRC_TOP1_VAL ((MUX_ACLK_400_G3D_SEL << 28) \
+ |(MUX_ACLK_400_ISP_SEL << 24) \
+ |(MUX_ACLK_400_IOP_SEL << 20) \
+ |(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16) \
+ |(MUX_ACLK_300_GSCL_MID1_SEL << 12) \
+ |(MUX_ACLK_300_DISP1_MID1_SEL << 8))
/* CLK_SRC_TOP2 */
-#define MUX_BPLL_USER_SEL 0x1
-#define MUX_MPLL_USER_SEL 0x1
-#define MUX_VPLL_SEL 0x0
-#define MUX_EPLL_SEL 0x0
-#define MUX_CPLL_SEL 0x0
-#define VPLLSRC_SEL 0x0
-#define CLK_SRC_TOP2_VAL ((MUX_BPLL_USER_SEL << 24) \
- | (MUX_MPLL_USER_SEL << 20) \
- | (MUX_VPLL_SEL << 16) \
- | (MUX_EPLL_SEL << 12) \
- | (MUX_CPLL_SEL << 8) \
+#define MUX_GPLL_SEL 0x1
+#define MUX_BPLL_USER_SEL 0x0
+#define MUX_MPLL_USER_SEL 0x0
+#define MUX_VPLL_SEL 0x1
+#define MUX_EPLL_SEL 0x1
+#define MUX_CPLL_SEL 0x1
+#define VPLLSRC_SEL 0x0
+#define CLK_SRC_TOP2_VAL ((MUX_GPLL_SEL << 28) \
+ | (MUX_BPLL_USER_SEL << 24) \
+ | (MUX_MPLL_USER_SEL << 20) \
+ | (MUX_VPLL_SEL << 16) \
+ | (MUX_EPLL_SEL << 12) \
+ | (MUX_CPLL_SEL << 8) \
| (VPLLSRC_SEL))
/* CLK_SRC_TOP3 */
-#define MUX_ACLK_333_SUB_SEL 0x1
-#define MUX_ACLK_400_SUB_SEL 0x1
-#define MUX_ACLK_266_ISP_SUB_SEL 0x1
-#define MUX_ACLK_266_GPS_SUB_SEL 0x1
-#define MUX_ACLK_300_GSCL_SUB_SEL 0x1
-#define MUX_ACLK_266_GSCL_SUB_SEL 0x1
-#define MUX_ACLK_300_DISP1_SUB_SEL 0x1
-#define MUX_ACLK_200_DISP1_SUB_SEL 0x1
-#define CLK_SRC_TOP3_VAL ((MUX_ACLK_333_SUB_SEL << 24) \
- | (MUX_ACLK_400_SUB_SEL << 20) \
- | (MUX_ACLK_266_ISP_SUB_SEL << 16) \
- | (MUX_ACLK_266_GPS_SUB_SEL << 12) \
- | (MUX_ACLK_300_GSCL_SUB_SEL << 10) \
- | (MUX_ACLK_266_GSCL_SUB_SEL << 8) \
- | (MUX_ACLK_300_DISP1_SUB_SEL << 6) \
- | (MUX_ACLK_200_DISP1_SUB_SEL << 4))
-
-/* CLK_DIV_TOP0 */
-#define ACLK_300_RATIO 0x0
-#define ACLK_400_RATIO 0x3
-#define ACLK_333_RATIO 0x2
+#define MUX_ACLK_333_SUB_SEL 0x1
+#define MUX_ACLK_400_SUB_SEL 0x1
+#define MUX_ACLK_266_ISP_SUB_SEL 0x1
+#define MUX_ACLK_266_GPS_SUB_SEL 0x0
+#define MUX_ACLK_300_GSCL_SUB_SEL 0x1
+#define MUX_ACLK_266_GSCL_SUB_SEL 0x1
+#define MUX_ACLK_300_DISP1_SUB_SEL 0x1
+#define MUX_ACLK_200_DISP1_SUB_SEL 0x1
+#define CLK_SRC_TOP3_VAL ((MUX_ACLK_333_SUB_SEL << 24) \
+ | (MUX_ACLK_400_SUB_SEL << 20) \
+ | (MUX_ACLK_266_ISP_SUB_SEL << 16) \
+ | (MUX_ACLK_266_GPS_SUB_SEL << 12) \
+ | (MUX_ACLK_300_GSCL_SUB_SEL << 10) \
+ | (MUX_ACLK_266_GSCL_SUB_SEL << 8) \
+ | (MUX_ACLK_300_DISP1_SUB_SEL << 6) \
+ | (MUX_ACLK_200_DISP1_SUB_SEL << 4))
+
+/* CLK_DIV_TOP0 */
+#define ACLK_300_DISP1_RATIO 0x2
+#define ACLK_400_G3D_RATIO 0x0
+#define ACLK_333_RATIO 0x0
#define ACLK_266_RATIO 0x2
#define ACLK_200_RATIO 0x3
-#define ACLK_166_RATIO 0x5
+#define ACLK_166_RATIO 0x1
#define ACLK_133_RATIO 0x1
#define ACLK_66_RATIO 0x5
-#define CLK_DIV_TOP0_VAL ((ACLK_300_RATIO << 28) \
- | (ACLK_400_RATIO << 24) \
- | (ACLK_333_RATIO << 20) \
- | (ACLK_266_RATIO << 16) \
- | (ACLK_200_RATIO << 12) \
- | (ACLK_166_RATIO << 8) \
- | (ACLK_133_RATIO << 4) \
+
+#define CLK_DIV_TOP0_VAL ((ACLK_300_DISP1_RATIO << 28) \
+ | (ACLK_400_G3D_RATIO << 24) \
+ | (ACLK_333_RATIO << 20) \
+ | (ACLK_266_RATIO << 16) \
+ | (ACLK_200_RATIO << 12) \
+ | (ACLK_166_RATIO << 8) \
+ | (ACLK_133_RATIO << 4) \
| (ACLK_66_RATIO))
-/* CLK_DIV_TOP1 */
-#define ACLK_MIPI_HSI_TX_BASE_RATIO 0x3
-#define ACLK_66_PRE_RATIO 0x1
-#define ACLK_400_ISP_RATIO 0x1
-#define ACLK_400_IOP_RATIO 0x1
-#define ACLK_300_GSCL_RATIO 0x0
-#define ACLK_266_GPS_RATIO 0x7
-
-#define CLK_DIV_TOP1_VAL ((ACLK_MIPI_HSI_TX_BASE_RATIO << 28) \
- | (ACLK_66_PRE_RATIO << 24) \
- | (ACLK_400_ISP_RATIO << 20) \
- | (ACLK_400_IOP_RATIO << 16) \
- | (ACLK_300_GSCL_RATIO << 12) \
- | (ACLK_266_GPS_RATIO << 8))
-
-/* APLL_LOCK */
-#define APLL_LOCK_VAL (0x3E8)
-/* MPLL_LOCK */
-#define MPLL_LOCK_VAL (0x2F1)
-/* CPLL_LOCK */
-#define CPLL_LOCK_VAL (0x3E8)
-/* EPLL_LOCK */
-#define EPLL_LOCK_VAL (0x2321)
-/* VPLL_LOCK */
-#define VPLL_LOCK_VAL (0x2321)
-/* BPLL_LOCK */
-#define BPLL_LOCK_VAL (0x3E8)
+/* CLK_DIV_TOP1 */
+#define ACLK_MIPI_HSI_TX_BASE_RATIO 0x3
+#define ACLK_66_PRE_RATIO 0x1
+#define ACLK_400_ISP_RATIO 0x1
+#define ACLK_400_IOP_RATIO 0x1
+#define ACLK_300_GSCL_RATIO 0x2
+
+#define CLK_DIV_TOP1_VAL ((ACLK_MIPI_HSI_TX_BASE_RATIO << 28) \
+ | (ACLK_66_PRE_RATIO << 24) \
+ | (ACLK_400_ISP_RATIO << 20) \
+ | (ACLK_400_IOP_RATIO << 16) \
+ | (ACLK_300_GSCL_RATIO << 12))
+
+/* APLL_LOCK */
+#define APLL_LOCK_VAL (0x546)
+/* MPLL_LOCK */
+#define MPLL_LOCK_VAL (0x546)
+/* CPLL_LOCK */
+#define CPLL_LOCK_VAL (0x546)
+/* GPLL_LOCK */
+#define GPLL_LOCK_VAL (0x546)
+/* EPLL_LOCK */
+#define EPLL_LOCK_VAL (0x3A98)
+/* VPLL_LOCK */
+#define VPLL_LOCK_VAL (0x3A98)
+/* BPLL_LOCK */
+#define BPLL_LOCK_VAL (0x546)
+
+#define MUX_APLL_SEL_MASK (1 << 0)
+#define MUX_MPLL_SEL_MASK (1 << 8)
+#define MPLL_SEL_MOUT_MPLLFOUT (2 << 8)
+#define MUX_CPLL_SEL_MASK (1 << 8)
+#define MUX_EPLL_SEL_MASK (1 << 12)
+#define MUX_VPLL_SEL_MASK (1 << 16)
+#define MUX_GPLL_SEL_MASK (1 << 28)
+#define MUX_BPLL_SEL_MASK (1 << 0)
+#define MUX_HPM_SEL_MASK (1 << 20)
+#define HPM_SEL_SCLK_MPLL (1 << 21)
+#define APLL_CON0_LOCKED (1 << 29)
+#define MPLL_CON0_LOCKED (1 << 29)
+#define BPLL_CON0_LOCKED (1 << 29)
+#define CPLL_CON0_LOCKED (1 << 29)
+#define EPLL_CON0_LOCKED (1 << 29)
+#define GPLL_CON0_LOCKED (1 << 29)
+#define VPLL_CON0_LOCKED (1 << 29)
+#define CLK_REG_DISABLE 0x0
+#define TOP2_VAL 0x0110000
/* CLK_SRC_PERIC0 */
+#define PWM_SEL 0
+#define UART3_SEL 6
+#define UART2_SEL 6
+#define UART1_SEL 6
+#define UART0_SEL 6
+/* SRC_CLOCK = SCLK_MPLL */
+#define CLK_SRC_PERIC0_VAL ((PWM_SEL << 24) \
+ | (UART3_SEL << 12) \
+ | (UART2_SEL << 8) \
+ | (UART1_SEL << 4) \
+ | (UART0_SEL))
+
+/* CLK_SRC_PERIC1 */
/* SRC_CLOCK = SCLK_MPLL */
-#define PWM_SEL 0
-#define UART4_SEL 6
-#define UART3_SEL 6
-#define UART2_SEL 6
-#define UART1_SEL 6
-#define UART0_SEL 6
-#define CLK_SRC_PERIC0_VAL ((PWM_SEL << 24) \
- | (UART4_SEL << 16) \
- | (UART3_SEL << 12) \
- | (UART2_SEL << 8) \
- | (UART1_SEL << 4) \
- | (UART0_SEL << 0))
-
-#define CLK_SRC_FSYS_VAL 0x66666
-#define CLK_DIV_FSYS0_VAL 0x0BB00000
-#define CLK_DIV_FSYS1_VAL 0x000f000f
-#define CLK_DIV_FSYS2_VAL 0x020f020f
-#define CLK_DIV_FSYS3_VAL 0x000f
-
-/* CLK_DIV_PERIC0 */
-#define UART5_RATIO 8
-#define UART4_RATIO 8
-#define UART3_RATIO 8
-#define UART2_RATIO 8
-#define UART1_RATIO 8
-#define UART0_RATIO 8
-#define CLK_DIV_PERIC0_VAL ((UART4_RATIO << 16) \
- | (UART3_RATIO << 12) \
- | (UART2_RATIO << 8) \
- | (UART1_RATIO << 4) \
- | (UART0_RATIO << 0))
+#define SPI0_SEL 6
+#define SPI1_SEL 6
+#define SPI2_SEL 6
+#define CLK_SRC_PERIC1_VAL ((SPI2_SEL << 24) \
+ | (SPI1_SEL << 20) \
+ | (SPI0_SEL << 16))
+
+/* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */
+#define SPI0_ISP_SEL 6
+#define SPI1_ISP_SEL 6
+#define SCLK_SRC_ISP_VAL (SPI1_ISP_SEL << 4) \
+ | (SPI0_ISP_SEL << 0)
+
+/* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */
+#define SPI0_ISP_RATIO 0xf
+#define SPI1_ISP_RATIO 0xf
+#define SCLK_DIV_ISP_VAL (SPI1_ISP_RATIO << 12) \
+ | (SPI0_ISP_RATIO << 0)
+
+/* CLK_DIV_PERIL0 */
+#define UART5_RATIO 7
+#define UART4_RATIO 7
+#define UART3_RATIO 7
+#define UART2_RATIO 7
+#define UART1_RATIO 7
+#define UART0_RATIO 7
+
+#define CLK_DIV_PERIC0_VAL ((UART3_RATIO << 12) \
+ | (UART2_RATIO << 8) \
+ | (UART1_RATIO << 4) \
+ | (UART0_RATIO))
+/* CLK_DIV_PERIC1 */
+#define SPI1_RATIO 0x7
+#define SPI0_RATIO 0xf
+#define SPI1_SUB_RATIO 0x0
+#define SPI0_SUB_RATIO 0x0
+#define CLK_DIV_PERIC1_VAL ((SPI1_SUB_RATIO << 24) \
+ | ((SPI1_RATIO << 16) \
+ | (SPI0_SUB_RATIO << 8) \
+ | (SPI0_RATIO << 0)))
+
+/* CLK_DIV_PERIC2 */
+#define SPI2_RATIO 0xf
+#define SPI2_SUB_RATIO 0x0
+#define CLK_DIV_PERIC2_VAL ((SPI2_SUB_RATIO << 8) \
+ | (SPI2_RATIO << 0))
/* CLK_DIV_PERIC3 */
#define PWM_RATIO 8
#define CLK_DIV_PERIC3_VAL (PWM_RATIO << 0)
+/* CLK_DIV_FSYS2 */
+#define MMC2_RATIO_MASK 0xf
+#define MMC2_RATIO_VAL 0x3
+#define MMC2_RATIO_OFFSET 0
+
+#define MMC2_PRE_RATIO_MASK 0xff
+#define MMC2_PRE_RATIO_VAL 0x9
+#define MMC2_PRE_RATIO_OFFSET 8
+
+#define MMC3_RATIO_MASK 0xf
+#define MMC3_RATIO_VAL 0x1
+#define MMC3_RATIO_OFFSET 16
+
+#define MMC3_PRE_RATIO_MASK 0xff
+#define MMC3_PRE_RATIO_VAL 0x0
+#define MMC3_PRE_RATIO_OFFSET 24
+
/* CLK_SRC_LEX */
-#define CLK_SRC_LEX_VAL 0x0
+#define CLK_SRC_LEX_VAL 0x0
/* CLK_DIV_LEX */
-#define CLK_DIV_LEX_VAL 0x10
+#define CLK_DIV_LEX_VAL 0x10
/* CLK_DIV_R0X */
-#define CLK_DIV_R0X_VAL 0x10
+#define CLK_DIV_R0X_VAL 0x10
/* CLK_DIV_L0X */
-#define CLK_DIV_R1X_VAL 0x10
+#define CLK_DIV_R1X_VAL 0x10
-/* SCLK_SRC_ISP */
-#define SCLK_SRC_ISP_VAL 0x600
/* CLK_DIV_ISP0 */
-#define CLK_DIV_ISP0_VAL 0x31
+#define CLK_DIV_ISP0_VAL 0x31
/* CLK_DIV_ISP1 */
-#define CLK_DIV_ISP1_VAL 0x0
+#define CLK_DIV_ISP1_VAL 0x0
/* CLK_DIV_ISP2 */
-#define CLK_DIV_ISP2_VAL 0x1
+#define CLK_DIV_ISP2_VAL 0x1
-#define MPLL_DEC (MPLL_MDIV * MPLL_MDIV / (MPLL_PDIV * 2^(MPLL_SDIV-1)))
+/* CLK_SRC_DISP1_0 */
+#define CLK_SRC_DISP1_0_VAL 0x6
+
+/*
+ * DIV_DISP1_0
+ * For DP, divisor should be 2
+ */
+#define CLK_DIV_DISP1_0_FIMD1 (2 << 0)
+
+/* CLK_GATE_IP_DISP1 */
+#define CLK_GATE_DP1_ALLOW (1 << 4)
/*
* TZPC Register Value :
@@ -347,103 +469,66 @@
*/
#define DECPROTXSET 0xFF
-/* DMC Init */
-#define SET 1
-#define RESET 0
-/* (Memory Interleaving Size = 1 << IV_SIZE) */
-#define CONFIG_IV_SIZE 0x07
+#define DDR3PHY_CTRL_PHY_RESET (1 << 0)
+#define DDR3PHY_CTRL_PHY_RESET_OFF (0 << 0)
+
+#define PHY_CON0_RESET_VAL 0x17020a40
+#define P0_CMD_EN (1 << 14)
+#define BYTE_RDLVL_EN (1 << 13)
+#define CTRL_SHGATE (1 << 8)
+
+#define PHY_CON1_RESET_VAL 0x09210100
+#define CTRL_GATEDURADJ_MASK (0xf << 20)
-#define PHY_RESET_VAL (0 << 0)
+#define PHY_CON2_RESET_VAL 0x00010004
+#define INIT_DESKEW_EN (1 << 6)
+#define RDLVL_GATE_EN (1 << 24)
/*ZQ Configurations */
#define PHY_CON16_RESET_VAL 0x08000304
-#define ZQ_MODE_DDS_VAL (0x5 << 24)
-#define ZQ_MODE_TERM_VAL (0x5 << 21)
-#define SET_ZQ_MODE_DDS_VAL(x) (x = (x & ~(0x7 << 24)) | ZQ_MODE_DDS_VAL)
-#define SET_ZQ_MODE_TERM_VAL(x) (x = (x & ~(0x7 << 21)) | ZQ_MODE_TERM_VAL)
-
-#define ZQ_MODE_NOTERM (1 << 19)
#define ZQ_CLK_DIV_EN (1 << 18)
#define ZQ_MANUAL_STR (1 << 1)
+#define ZQ_DONE (1 << 0)
+
+#define CTRL_RDLVL_GATE_ENABLE 1
+#define CTRL_RDLVL_GATE_DISABLE 1
+
+/* Direct Command */
+#define DIRECT_CMD_NOP 0x07000000
+#define DIRECT_CMD_PALL 0x01000000
+#define DIRECT_CMD_ZQINIT 0x0a000000
+#define DIRECT_CMD_CHANNEL_SHIFT 28
+#define DIRECT_CMD_CHIP_SHIFT 20
+
+/* DMC PHY Control0 register */
+#define PHY_CONTROL0_RESET_VAL 0x0
+#define MEM_TERM_EN (1 << 31) /* Termination enable for memory */
+#define PHY_TERM_EN (1 << 30) /* Termination enable for PHY */
+#define DMC_CTRL_SHGATE (1 << 29) /* Duration of DQS gating signal */
+#define FP_RSYNC (1 << 3) /* Force DLL resyncronization */
+
+/* Driver strength for CK, CKE, CS & CA */
+#define IMP_OUTPUT_DRV_40_OHM 0x5
+#define IMP_OUTPUT_DRV_30_OHM 0x7
+#define CA_CK_DRVR_DS_OFFSET 9
+#define CA_CKE_DRVR_DS_OFFSET 6
+#define CA_CS_DRVR_DS_OFFSET 3
+#define CA_ADR_DRVR_DS_OFFSET 0
+
+#define PHY_CON42_CTRL_BSTLEN_SHIFT 8
+#define PHY_CON42_CTRL_RDLAT_SHIFT 0
+
+struct mem_timings;
+
+/* Errors that we can encourter in low-level setup */
+enum {
+ SETUP_ERR_OK,
+ SETUP_ERR_RDLV_COMPLETE_TIMEOUT = -1,
+ SETUP_ERR_ZQ_CALIBRATION_FAILURE = -2,
+};
-/* Channel and Chip Selection */
-#define CONFIG_DMC_CHANNELS 2
-#define CONFIG_CHIPS_PER_CHANNEL 2
-
-#define SET_CMD_CHANNEL(x, y) (x = (x & ~(1 << 28)) | y << 28)
-#define SET_CMD_CHIP(x, y) (x = (x & ~(1 << 20)) | y << 20)
-
-/* Diret Command */
-#define DIRECT_CMD_NOP 0x07000000
-#define DIRECT_CMD_MRS1 0x00071C00
-#define DIRECT_CMD_MRS2 0x00010BFC
-#define DIRECT_CMD_MRS3 0x00000708
-#define DIRECT_CMD_MRS4 0x00000818
-#define DIRECT_CMD_PALL 0x01000000
-
-/* DLL Resync */
-#define FP_RSYNC (1 << 3)
-
-#define CONFIG_CTRL_DLL_ON(x, y) (x = (x & ~(1 << 5)) | y << 5)
-#define CONFIG_CTRL_START(x, y) (x = (x & ~(1 << 6)) | y << 6)
-#define SET_CTRL_FORCE_VAL(x, y) (x = (x & ~(0x7F << 8)) | y << 8)
-
-/* RDLVL */
-#define PHY_CON0_RESET_VAL 0x17023240
-#define DDR_MODE_LPDDR2 0x2
-#define BYTE_RDLVL_EN (1 << 13)
-#define CTRL_ATGATE (1 << 6)
-#define SET_CTRL_DDR_MODE(x, y) (x = (x & ~(0x3 << 11)) | y << 11)
-
-#define PHY_CON1_RESET_VAL 0x9210100
-#define RDLVL_RDDATAPADJ 0x1
-#define SET_RDLVL_RDDATAPADJ ((PHY_CON1_RESET_VAL & ~(0xFFFF << 0))\
- | RDLVL_RDDATAPADJ << 0)
-
-#define PHY_CON2_RESET_VAL 0x00010004
-#define RDLVL_EN (1 << 25)
-#define RDDSKEW_CLEAR (1 << 13)
-
-#define CTRL_RDLVL_DATA_EN (1 << 1)
-#define LPDDR2_ADDR 0x00000208
-
-#define DMC_MEMCONFIG0_VAL 0x00001323
-#define DMC_MEMCONFIG1_VAL 0x00001323
-#define DMC_MEMBASECONFIG0_VAL 0x00400780
-#define DMC_MEMBASECONFIG1_VAL 0x00800780
-#define DMC_MEMCONTROL_VAL 0x00212500
-#define DMC_PRECHCONFIG_VAL 0xFF000000
-#define DMC_PWRDNCONFIG_VAL 0xFFFF00FF
-#define DMC_TIMINGREF_VAL 0x0000005D
-#define DMC_TIMINGROW_VAL 0x2336544C
-#define DMC_TIMINGDATA_VAL 0x24202408
-#define DMC_TIMINGPOWER_VAL 0x38260235
-
-#define CTRL_BSTLEN 0x04
-#define CTRL_RDLAT 0x08
-#define PHY_CON42_VAL (CTRL_BSTLEN << 8 | CTRL_RDLAT << 0)
-
-/* DQS, DQ, DEBUG offsets */
-#define SET_DQS_OFFSET_VAL 0x7F7F7F7F
-#define SET_DQ_OFFSET_VAL 0x7F7F7F7F
-#define SET_DEBUG_OFFSET_VAL 0x7F
-
-#define RESET_DQS_OFFSET_VAL 0x08080808
-#define RESET_DQ_OFFSET_VAL 0x08080808
-#define RESET_DEBUG_OFFSET_VAL 0x8
-
-#define CTRL_PULLD_DQ (0x0F << 8)
-#define CTRL_PULLD_DQS (0x0F << 0)
-
-#define DFI_INIT_START (1 << 28)
-
-#define CLK_STOP_EN (1 << 0)
-#define DPWRDN_EN (1 << 1)
-#define DSREF_EN (1 << 5)
-#define AREF_EN (1 << 5)
-void sdelay(unsigned long);
void mem_ctrl_init(void);
void system_clock_init(void);
void tzpc_init(void);
--
1.7.4.4
More information about the U-Boot
mailing list