[U-Boot] Please pull u-boot-ti/next
Albert ARIBAUD
albert.u.boot at aribaud.net
Mon Jul 9 22:39:36 CEST 2012
Hi Tom,
On Mon, 9 Jul 2012 11:46:11 -0700, Tom Rini <trini at ti.com> wrote:
> Hello,
>
> The following changes since commit d702b0811df53a1fc2d8049e35431e4591d093c6:
>
> ARM: cache: Move the cp15 CR register read before flushing the cache. (2012-07-07 14:07:44 +0200)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-ti next
>
> for you to fetch changes up to 9af1a780c81639ca4b6f7035530dc8c7151bf201:
>
> omap: am335x_evm: enable i2c1 channel (2012-07-09 11:12:19 -0700)
>
> ----------------------------------------------------------------
> Igor Grinberg (1):
> arm: omap3: cm-t35: minor comment and printf change
>
> Ilya Yanok (1):
> omap24xx_i2c: add 2-byte address support
>
> Javier Martinez Canillas (2):
> igep00x0: default to OMAP-specific serial driver
> igep00x0: default mmcrootfstype to EXT4
>
> Lad, Prabhakar (7):
> da850/omap-l138: Add MMC support for DA850/OMAP-L138
> arm, davinci: perform check for initializing global data and serial init
> da850/omap-l138: Define SPI specific configs for SPL only when SPI is used
> da850/omap-l138: Add support to read u-boot image from MMC/SD
> da850/omap-l138: Fix NAND flash timings
> da850/omap-l138: Add support for NAND SPL
> da850/omap-l138: add support for direct NOR boot mode
>
> Peter Meerwald (4):
> beagle: add eeprom expansion board info for bct brettl4
> beagle: make get_expansion_id(), get_board_revision(), beagle_display_init() static
> beagle: fix termination of buddy env setting
> beagle: removed unused pr_debug #define
>
> Rajashekhara, Sudhakar (2):
> da850/omap-l138: modifications for Logic PD Rev.3 AM18xx EVM
> da850/omap-l138: Make MMC and NOR support mutually exclusive
>
> Stefano Babic (4):
> mcx: increased buffer for command line
> OMAP3: mcx: set pinmux for uart4
> OMAP3: mcx: updated default environment
> OMAP3: mcx: read hot-water-button after reset
>
> Steve Sakoman (3):
> omap: am335x_evm: remove unused definitions
> omap: am33xx: enable gpio support
> omap: am335x_evm: enable i2c1 channel
>
> Sughosh Ganu (1):
> hawkboard/omapl-138: Add support for generating ais image for hawkboard
>
> .gitignore | 3 +
> Makefile | 5 +-
> arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c | 11 ++
> arch/arm/cpu/arm926ejs/davinci/spl.c | 20 ++--
> arch/arm/cpu/armv7/am33xx/board.c | 10 ++
> arch/arm/cpu/armv7/am33xx/clock.c | 20 ++++
> arch/arm/cpu/armv7/omap-common/Makefile | 2 +-
> arch/arm/include/asm/arch-am33xx/cpu.h | 20 ++++
> arch/arm/include/asm/arch-am33xx/gpio.h | 29 +++++
> arch/arm/include/asm/arch-davinci/hardware.h | 1 +
> arch/arm/include/asm/arch-davinci/pinmux_defs.h | 3 +
> board/cm_t35/cm_t35.c | 4 +-
> board/davinci/da8xxevm/da850evm.c | 54 ++++++++--
> board/davinci/da8xxevm/hawkboard-ais-nand.cfg | 4 +
> board/htkw/mcx/mcx.c | 23 ++++
> board/htkw/mcx/mcx.h | 11 +-
> board/ti/am335x/evm.c | 6 +-
> board/ti/am335x/mux.c | 13 +++
> board/ti/beagle/beagle.c | 16 +--
> boards.cfg | 1 +
> drivers/i2c/omap24xx_i2c.c | 58 +++++-----
> drivers/mmc/Makefile | 4 +
> drivers/mmc/spl_mmc_load.c | 62 +++++++++++
> include/configs/am335x_evm.h | 2 +-
> include/configs/da850evm.h | 93 ++++++++++++++--
> include/configs/hawkboard.h | 1 +
> include/configs/igep00x0.h | 4 +-
> include/configs/mcx.h | 132 ++++++++++++++++-------
> include/configs/omap3_beagle.h | 2 +-
> include/mmc.h | 2 +
> 30 files changed, 502 insertions(+), 114 deletions(-)
> create mode 100644 arch/arm/include/asm/arch-am33xx/gpio.h
> create mode 100644 board/davinci/da8xxevm/hawkboard-ais-nand.cfg
> create mode 100644 drivers/mmc/spl_mmc_load.c
>
> This includes the single patch I asked for in u-boot-ti/master as well
> as a number of other small clean-ups, bugfixes or enhancements that have
> been around for a bit, but did not meet the merge window and I don't
> want to forget them. If you want me to carry them in my own /next
> branch until -rc1 comes out, that's fine and this can just serve as
> notice to interested parties that yes, really, patches have been picked
> up.
Applied to u-boot-arm/next, to be moved to master after the 12.07 release.
Amicalement,
--
Albert.
More information about the U-Boot
mailing list