[U-Boot] [PATCH v2] kirkwood: add support for Iomega iConnect board
Luka Perkov
uboot at lukaperkov.net
Thu Jul 19 17:15:06 CEST 2012
Add support for new board iConnect from Iomega.
More information about the device can be found here:
http://go.iomega.com/en/products/network-storage-desktop/wireless-data-station/network-hard-drive-iconnect/?partner=4735
Signed-off-by: Luka Perkov <uboot at lukaperkov.net>
Tested-by: Wojciech Dubowik <wojciech.dubowik at neratec.com>
Tested-by: Tim Fletcher <tim at night-shade.org.uk>
---
Changes from v1:
* remove #ifdef CONFIG_CMD_IDE part from include/configs/iconnect.h
(board does not have IDE ports)
* add compression defines in include/configs/iconnect.h
MAINTAINERS | 1 +
board/iomega/iconnect/Makefile | 43 ++++++++++
board/iomega/iconnect/iconnect.c | 107 +++++++++++++++++++++++
board/iomega/iconnect/iconnect.h | 39 +++++++++
board/iomega/iconnect/kwbimage.cfg | 165 ++++++++++++++++++++++++++++++++++++
boards.cfg | 1 +
include/configs/iconnect.h | 129 ++++++++++++++++++++++++++++
7 files changed, 485 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index fd0c65c..9e9d8d7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -787,6 +787,7 @@ Linus Walleij <linus.walleij at linaro.org>
Luka Perkov <uboot at lukaperkov.net>
ib62x0 ARM926EJS
+ iconnect ARM926EJS
Dave Peverley <dpeverley at mpc-data.co.uk>
diff --git a/board/iomega/iconnect/Makefile b/board/iomega/iconnect/Makefile
new file mode 100644
index 0000000..f77fcfb
--- /dev/null
+++ b/board/iomega/iconnect/Makefile
@@ -0,0 +1,43 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program. If not, see <http://www.gnu.org/licenses/>.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := iconnect.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/iomega/iconnect/iconnect.c b/board/iomega/iconnect/iconnect.c
new file mode 100644
index 0000000..6ee3b84
--- /dev/null
+++ b/board/iomega/iconnect/iconnect.c
@@ -0,0 +1,107 @@
+/*
+ * Copyright (C) 2009-2012
+ * Wojciech Dubowik <wojciech.dubowik at neratec.com>
+ * Luka Perkov <uboot at lukaperkov.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "iconnect.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(ICONNECT_OE_VAL_LOW,
+ ICONNECT_OE_VAL_HIGH,
+ ICONNECT_OE_LOW, ICONNECT_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_GPO,
+ MPP13_SD_CMD,
+ MPP14_SD_D0,
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0,
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GPIO,
+ MPP29_GPIO,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GE1_14,
+ MPP35_GPIO,
+ MPP36_AUDIO_SPDIFI,
+ MPP37_AUDIO_SPDIFO,
+ MPP38_GPIO,
+ MPP39_TDM_SPI_CS0,
+ MPP40_TDM_SPI_SCK,
+ MPP41_GPIO,
+ MPP42_GPIO,
+ MPP43_GPIO,
+ MPP44_GPIO,
+ MPP45_GPIO,
+ MPP46_GPIO,
+ MPP47_GPIO,
+ MPP48_GPIO,
+ MPP49_GPIO,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config, NULL);
+ return 0;
+}
+
+int board_init(void)
+{
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
diff --git a/board/iomega/iconnect/iconnect.h b/board/iomega/iconnect/iconnect.h
new file mode 100644
index 0000000..2fb3e5e
--- /dev/null
+++ b/board/iomega/iconnect/iconnect.h
@@ -0,0 +1,39 @@
+/*
+ * Copyright (C) 2009-2012
+ * Wojciech Dubowik <wojciech.dubowik at neratec.com>
+ * Luka Perkov <uboot at lukaperkov.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __ICONNECT_H
+#define __ICONNECT_H
+
+#define ICONNECT_OE_LOW (~(1 << 7))
+#define ICONNECT_OE_HIGH (~(1 << 10))
+#define ICONNECT_OE_VAL_LOW (0)
+#define ICONNECT_OE_VAL_HIGH (1 << 10)
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __ICONNECT_H */
diff --git a/board/iomega/iconnect/kwbimage.cfg b/board/iomega/iconnect/kwbimage.cfg
new file mode 100644
index 0000000..6c9dfe3
--- /dev/null
+++ b/board/iomega/iconnect/kwbimage.cfg
@@ -0,0 +1,165 @@
+#
+# (C) Copyright 2009-2012
+# Wojciech Dubowik <wojciech.dubowik at neratec.com>
+# Luka Perkov <uboot at lukaperkov.net>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program. If not, see <http://www.gnu.org/licenses/>.
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xffd100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xffd01400 0x43000c30 # DDR Configuration register
+# bit13-0: 0xc30, (3120 DDR2 clks refresh rate)
+# bit23-14: 0x0,
+# bit24: 0x1, enable exit self refresh mode on DDR access
+# bit25: 0x1, required
+# bit29-26: 0x0,
+# bit31-30: 0x1,
+
+DATA 0xffd01404 0x37543000 # DDR Controller Control Low
+# bit4: 0x0, addr/cmd in smame cycle
+# bit5: 0x0, clk is driven during self refresh, we don't care for APX
+# bit6: 0x0, use recommended falling edge of clk for addr/cmd
+# bit14: 0x0, input buffer always powered up
+# bit18: 0x1, cpu lock transaction enabled
+# bit23-20: 0x5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 0x7, CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 0x3, required
+# bit31: 0x0, no additional STARTBURST delay
+
+DATA 0xffd01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11-8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xffd0140c 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: 0x0, required
+
+DATA 0xffd01410 0x000000cc # DDR Address Control
+# bit1-0: 00, Cs0width (x8)
+# bit3-2: 11, Cs0size (1Gb)
+# bit5-4: 00, Cs1width (x8)
+# bit7-6: 11, Cs1size (1Gb)
+# bit9-8: 00, Cs2width (nonexistent)
+# bit11-10: 00, Cs2size (nonexistent)
+# bit13-12: 00, Cs3width (nonexistent)
+# bit15-14: 00, Cs3size (nonexistent)
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0x0, required
+
+DATA 0xffd01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0x0, required
+
+DATA 0xffd01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0x0, required
+
+DATA 0xffd0141c 0x00000c52 # DDR Mode
+# bit2-0: 0x2, BurstLen=2 required
+# bit3: 0x0, BurstType=0 required
+# bit6-4: 0x4, CL=5
+# bit7: 0x0, TestMode=0 normal
+# bit8: 0x0, DLL reset=0 normal
+# bit11-9: 0x6, auto-precharge write recovery ????????????
+# bit12: 0x0, PD must be zero
+# bit31-13: 0x0, required
+
+DATA 0xffd01420 0x00000040 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 0, DDR drive strenght normal
+# bit2: 0, DDR ODT control lsd (disabled)
+# bit5-3: 0x0, required
+# bit6: 1, DDR ODT control msb, (disabled)
+# bit9-7: 0x0, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0x0, required
+
+DATA 0xffd01424 0x0000f17f # DDR Controller Control High
+# bit2-0: 0x7, required
+# bit3: 0x1, MBUS Burst Chop disabled
+# bit6-4: 0x7, required
+# bit7: 0x0,
+# bit8: 0x1, add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9: 0x0, no half clock cycle addition to dataout
+# bit10: 0x0, 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11: 0x0, 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 0xf, required
+# bit31-16: 0x0, required
+
+DATA 0xffd01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xffd0147c 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xffd01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xffd01504 0x0ffffff1 # CS[0]n Size
+# bit0: 0x1, Window enabled
+# bit1: 0x0, Write Protect disabled
+# bit3-2: 0x0, CS0 hit selected
+# bit23-4: 0xfffff, required
+# bit31-24: 0x0f, Size (i.e. 256MB)
+
+DATA 0xffd01508 0x00000000 # CS[1]n Base address to 256Mb
+DATA 0xffd0150c 0x00000000 # CS[1]n Size, window disabled
+
+DATA 0xffd01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xffd0151c 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xffd01494 0x00030000 # DDR ODT Control (Low)
+# bit3-0: ODT0Rd, MODT[0] asserted during read from DRAM CS1
+# bit7-4: ODT0Rd, MODT[0] asserted during read from DRAM CS0
+# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1
+# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
+
+DATA 0xffd01498 0x00000000 # DDR ODT Control (High)
+# bit1-0: 0x0, ODT0 controlled by ODT Control (low) register above
+# bit3-2: 0x1, ODT1 active NEVER!
+# bit31-4: 0x0, required
+
+DATA 0xffd0149c 0x0000e803 # CPU ODT Control
+DATA 0xffd01480 0x00000001 # DDR Initialization Control
+# bit0: 0x1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/boards.cfg b/boards.cfg
index 2d36d83..6dd8a05 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -140,6 +140,7 @@ enbw_cmc arm arm926ejs enbw_cmc enbw
calimain arm arm926ejs calimain omicron davinci
pogo_e02 arm arm926ejs - cloudengines kirkwood
dns325 arm arm926ejs - d-link kirkwood
+iconnect arm arm926ejs - iomega kirkwood
lschlv2 arm arm926ejs lsxl buffalo kirkwood lsxl:LSCHLV2
lsxhl arm arm926ejs lsxl buffalo kirkwood lsxl:LSXHL
km_kirkwood arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_KIRKWOOD
diff --git a/include/configs/iconnect.h b/include/configs/iconnect.h
new file mode 100644
index 0000000..125464a
--- /dev/null
+++ b/include/configs/iconnect.h
@@ -0,0 +1,129 @@
+/*
+ * (C) Copyright 2009-2012
+ * Wojciech Dubowik <wojciech.dubowik at neratec.com>
+ * Luka Perkov <uboot at lukaperkov.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _CONFIG_ICONNECT_H
+#define _CONFIG_ICONNECT_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING " Iomega iConnect Wireless"
+
+/*
+ * High level configuration options
+ */
+#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD /* SOC Family Name */
+#define CONFIG_KW88F6281 /* SOC Name */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+
+/*
+ * Machine type
+ */
+#define CONFIG_MACH_TYPE MACH_TYPE_ICONNECT
+
+/*
+ * Compression configuration
+ */
+#define CONFIG_BZIP2
+#define CONFIG_LZMA
+#define CONFIG_LZO
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* declare no flash (NOR/SPI) */
+#define CONFIG_SYS_MVFS
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+#undef CONFIG_SYS_PROMPT
+#define CONFIG_SYS_PROMPT "iconnect => "
+
+/*
+ * Environment variables configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#else
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+#define CONFIG_ENV_SIZE 0x20000
+#define CONFIG_ENV_OFFSET 0x80000
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND \
+ "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
+ "ubi part rootfs; " \
+ "ubifsmount rootfs; " \
+ "ubifsload 0x800000 ${kernel}; " \
+ "bootm 0x800000"
+
+#define CONFIG_MTDPARTS \
+ "mtdparts=orion_nand:" \
+ "0x80000 at 0x0(uboot)," \
+ "0x20000 at 0x80000(uboot_env)," \
+ "- at 0xa0000(rootfs)\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console=console=ttyS0,115200\0" \
+ "mtdids=nand0=orion_nand\0" \
+ "mtdparts="CONFIG_MTDPARTS \
+ "kernel=/boot/uImage\0" \
+ "bootargs_root=noinitrd ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs\0"
+
+/*
+ * Ethernet driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 11
+#undef CONFIG_RESET_PHY_R
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+
+#endif /* _CONFIG_ICONNECT_H */
More information about the U-Boot
mailing list