[U-Boot] [PATCH 03/10] dm: arm: Remove support for NETARM
Marek Vasut
marex at denx.de
Sat Jul 21 17:02:20 CEST 2012
This stuff has been rotting in the tree for a while now. Remove it.
Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Wolfgang Denk <wd at denx.de>
Cc: Albert Aribaud <albert.u.boot at aribaud.net>
Cc: U-Boot DM <u-boot-dm at lists.denx.de>
Cc: Curt Brune <curt at cucy.com>
---
arch/arm/cpu/arm720t/cpu.c | 13 +-
arch/arm/cpu/arm720t/interrupts.c | 118 +------
arch/arm/cpu/arm720t/start.S | 79 +----
.../include/asm/arch-arm720t/netarm_dma_module.h | 182 ----------
.../include/asm/arch-arm720t/netarm_eni_module.h | 121 -------
.../include/asm/arch-arm720t/netarm_eth_module.h | 160 ---------
.../include/asm/arch-arm720t/netarm_gen_module.h | 186 -----------
.../include/asm/arch-arm720t/netarm_mem_module.h | 184 ----------
.../include/asm/arch-arm720t/netarm_registers.h | 96 ------
.../include/asm/arch-arm720t/netarm_ser_module.h | 347 -------------------
drivers/net/Makefile | 1 -
drivers/net/netarm_eth.c | 352 --------------------
drivers/net/netarm_eth.h | 42 ---
drivers/serial/Makefile | 1 -
drivers/serial/serial_netarm.c | 190 -----------
15 files changed, 10 insertions(+), 2062 deletions(-)
delete mode 100644 arch/arm/include/asm/arch-arm720t/netarm_dma_module.h
delete mode 100644 arch/arm/include/asm/arch-arm720t/netarm_eni_module.h
delete mode 100644 arch/arm/include/asm/arch-arm720t/netarm_eth_module.h
delete mode 100644 arch/arm/include/asm/arch-arm720t/netarm_gen_module.h
delete mode 100644 arch/arm/include/asm/arch-arm720t/netarm_mem_module.h
delete mode 100644 arch/arm/include/asm/arch-arm720t/netarm_registers.h
delete mode 100644 arch/arm/include/asm/arch-arm720t/netarm_ser_module.h
delete mode 100644 drivers/net/netarm_eth.c
delete mode 100644 drivers/net/netarm_eth.h
delete mode 100644 drivers/serial/serial_netarm.c
diff --git a/arch/arm/cpu/arm720t/cpu.c b/arch/arm/cpu/arm720t/cpu.c
index 5db4146..c215ce3 100644
--- a/arch/arm/cpu/arm720t/cpu.c
+++ b/arch/arm/cpu/arm720t/cpu.c
@@ -36,6 +36,10 @@
#include <asm/hardware.h>
#include <asm/system.h>
+#if !defined(CONFIG_INTEGRATOR) || !defined(CONFIG_ARCH_INTEGRATOR)
+#error No cleanup_before_linux() defined for this CPU type
+#endif
+
int cleanup_before_linux (void)
{
/*
@@ -45,14 +49,5 @@ int cleanup_before_linux (void)
* we turn off caches etc ...
* and we set the CPU-speed to 73 MHz - see start.S for details
*/
-
-#if defined(CONFIG_NETARM)
- disable_interrupts ();
- /* Nothing more needed */
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
- /* No cleanup before linux for IntegratorAP/CM720T as yet */
-#else
-#error No cleanup_before_linux() defined for this CPU type
-#endif
return 0;
}
diff --git a/arch/arm/cpu/arm720t/interrupts.c b/arch/arm/cpu/arm720t/interrupts.c
index 68592b3..ed4af60 100644
--- a/arch/arm/cpu/arm720t/interrupts.c
+++ b/arch/arm/cpu/arm720t/interrupts.c
@@ -31,127 +31,17 @@
#include <asm/proc-armv/ptrace.h>
#include <asm/hardware.h>
-#ifndef CONFIG_NETARM
+#if !defined(CONFIG_INTEGRATOR) || !defined(CONFIG_ARCH_INTEGRATOR)
+#error Timer routines not defined for this CPU type
+#endif
+
/* we always count down the max. */
#define TIMER_LOAD_VAL 0xffff
/* macro to read the 16 bit timer */
#define READ_TIMER (IO_TC1D & 0xffff)
-#else
-#define IRQEN (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_INTR_ENABLE))
-#define TM2CTRL (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_TIMER2_CONTROL))
-#define TM2STAT (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_TIMER2_STATUS))
-#define TIMER_LOAD_VAL NETARM_GEN_TSTAT_CTC_MASK
-#define READ_TIMER (TM2STAT & NETARM_GEN_TSTAT_CTC_MASK)
-#endif
-
#ifdef CONFIG_USE_IRQ
void do_irq (struct pt_regs *pt_regs)
{
-#if defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
- /* No do_irq() for IntegratorAP/CM720T as yet */
-#else
-#error do_irq() not defined for this CPU type
-#endif
-}
-#endif
-
-#if defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
- /* Use IntegratorAP routines in board/integratorap.c */
-#else
-
-static ulong timestamp;
-static ulong lastdec;
-
-int timer_init (void)
-{
-#if defined(CONFIG_NETARM)
- /* disable all interrupts */
- IRQEN = 0;
-
- /* operate timer 2 in non-prescale mode */
- TM2CTRL = ( NETARM_GEN_TIMER_SET_HZ(CONFIG_SYS_HZ) |
- NETARM_GEN_TCTL_ENABLE |
- NETARM_GEN_TCTL_INIT_COUNT(TIMER_LOAD_VAL));
-
- /* set timer 2 counter */
- lastdec = TIMER_LOAD_VAL;
-#else
-#error No timer_init() defined for this CPU type
-#endif
- timestamp = 0;
-
- return (0);
-}
-
-#endif /* ! IntegratorAP */
-
-/*
- * timer without interrupts
- */
-
-
-#if defined(CONFIG_NETARM)
-
-ulong get_timer (ulong base)
-{
- return get_timer_masked () - base;
-}
-
-void __udelay (unsigned long usec)
-{
- ulong tmo;
-
- tmo = usec / 1000;
- tmo *= CONFIG_SYS_HZ;
- tmo /= 1000;
-
- tmo += get_timer (0);
-
- while (get_timer_masked () < tmo)
-}
-
-ulong get_timer_masked (void)
-{
- ulong now = READ_TIMER;
-
- if (lastdec >= now) {
- /* normal mode */
- timestamp += lastdec - now;
- } else {
- /* we have an overflow ... */
- timestamp += lastdec + TIMER_LOAD_VAL - now;
- }
- lastdec = now;
-
- return timestamp;
}
-
-void udelay_masked (unsigned long usec)
-{
- ulong tmo;
- ulong endtime;
- signed long diff;
-
- if (usec >= 1000) {
- tmo = usec / 1000;
- tmo *= CONFIG_SYS_HZ;
- tmo /= 1000;
- } else {
- tmo = usec * CONFIG_SYS_HZ;
- tmo /= (1000*1000);
- }
-
- endtime = get_timer_masked () + tmo;
-
- do {
- ulong now = get_timer_masked ();
- diff = endtime - now;
- } while (diff >= 0);
-}
-
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
- /* No timer routines for IntegratorAP/CM720T as yet */
-#else
-#error Timer routines not defined for this CPU type
#endif
diff --git a/arch/arm/cpu/arm720t/start.S b/arch/arm/cpu/arm720t/start.S
index 2af4d33..c53c824 100644
--- a/arch/arm/cpu/arm720t/start.S
+++ b/arch/arm/cpu/arm720t/start.S
@@ -265,60 +265,7 @@ _dynsym_start_ofs:
*/
cpu_init_crit:
-#if defined(CONFIG_NETARM)
- /*
- * prior to software reset : need to set pin PORTC4 to be *HRESET
- */
- ldr r0, =NETARM_GEN_MODULE_BASE
- ldr r1, =(NETARM_GEN_PORT_MODE(0x10) | \
- NETARM_GEN_PORT_DIR(0x10))
- str r1, [r0, #+NETARM_GEN_PORTC]
- /*
- * software reset : see HW Ref. Guide 8.2.4 : Software Service register
- * for an explanation of this process
- */
- ldr r0, =NETARM_GEN_MODULE_BASE
- ldr r1, =NETARM_GEN_SW_SVC_RESETA
- str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETB
- str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETA
- str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETB
- str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
- /*
- * setup PLL and System Config
- */
- ldr r0, =NETARM_GEN_MODULE_BASE
-
- ldr r1, =( NETARM_GEN_SYS_CFG_LENDIAN | \
- NETARM_GEN_SYS_CFG_BUSFULL | \
- NETARM_GEN_SYS_CFG_USER_EN | \
- NETARM_GEN_SYS_CFG_ALIGN_ABORT | \
- NETARM_GEN_SYS_CFG_BUSARB_INT | \
- NETARM_GEN_SYS_CFG_BUSMON_EN )
-
- str r1, [r0, #+NETARM_GEN_SYSTEM_CONTROL]
-
-#ifndef CONFIG_NETARM_PLL_BYPASS
- ldr r1, =( NETARM_GEN_PLL_CTL_PLLCNT(NETARM_PLL_COUNT_VAL) | \
- NETARM_GEN_PLL_CTL_POLTST_DEF | \
- NETARM_GEN_PLL_CTL_INDIV(1) | \
- NETARM_GEN_PLL_CTL_ICP_DEF | \
- NETARM_GEN_PLL_CTL_OUTDIV(2) )
- str r1, [r0, #+NETARM_GEN_PLL_CONTROL]
-#endif
-
- /*
- * mask all IRQs by clearing all bits in the INTMRs
- */
- mov r1, #0
- ldr r0, =NETARM_GEN_MODULE_BASE
- str r1, [r0, #+NETARM_GEN_INTR_ENABLE]
-
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
- /* No specific initialisation for IntegratorAP/CM720T as yet */
-#else
+#if !defined(CONFIG_INTEGRATOR) || !defined(CONFIG_ARCH_INTEGRATOR)
#error No cpu_init_crit() defined for current CPU type
#endif
@@ -507,28 +454,6 @@ fiq:
#endif
-#if defined(CONFIG_NETARM)
- .align 5
-.globl reset_cpu
-reset_cpu:
- ldr r1, =NETARM_MEM_MODULE_BASE
- ldr r0, [r1, #+NETARM_MEM_CS0_BASE_ADDR]
- ldr r1, =0xFFFFF000
- and r0, r1, r0
- ldr r1, =(relocate-CONFIG_SYS_TEXT_BASE)
- add r0, r1, r0
- ldr r4, =NETARM_GEN_MODULE_BASE
- ldr r1, =NETARM_GEN_SW_SVC_RESETA
- str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETB
- str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETA
- str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETB
- str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
- mov pc, r0
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
- /* No specific reset actions for IntegratorAP/CM720T as yet */
-#else
+#if !defined(CONFIG_INTEGRATOR) || !defined(CONFIG_ARCH_INTEGRATOR)
#error No reset_cpu() defined for current CPU type
#endif
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_dma_module.h b/arch/arm/include/asm/arch-arm720t/netarm_dma_module.h
deleted file mode 100644
index 328eaf0..0000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_dma_module.h
+++ /dev/null
@@ -1,182 +0,0 @@
-/* * include/asm-armnommu/arch-netarm/netarm_dma_module.h
- *
- * Copyright (C) 2000 NETsilicon, Inc.
- * Copyright (C) 2000 WireSpeed Communications Corporation
- *
- * This software is copyrighted by WireSpeed. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall WireSpeed
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Joe deBlaquiere
- * David Smith
- */
-
-#ifndef __NETARM_DMA_MODULE_REGISTERS_H
-#define __NETARM_DMA_MODULE_REGISTERS_H
-
-/* GEN unit register offsets */
-
-#define NETARM_DMA_MODULE_BASE (0xFF900000)
-
-#define get_dma_reg_addr(c) ((volatile unsigned int *)(NETARM_DMA_MODULE_BASE + (c)))
-
-#define NETARM_DMA1A_BFR_DESCRPTOR_PTR (0x00)
-#define NETARM_DMA1A_CONTROL (0x10)
-#define NETARM_DMA1A_STATUS (0x14)
-#define NETARM_DMA1B_BFR_DESCRPTOR_PTR (0x20)
-#define NETARM_DMA1B_CONTROL (0x30)
-#define NETARM_DMA1B_STATUS (0x34)
-#define NETARM_DMA1C_BFR_DESCRPTOR_PTR (0x40)
-#define NETARM_DMA1C_CONTROL (0x50)
-#define NETARM_DMA1C_STATUS (0x54)
-#define NETARM_DMA1D_BFR_DESCRPTOR_PTR (0x60)
-#define NETARM_DMA1D_CONTROL (0x70)
-#define NETARM_DMA1D_STATUS (0x74)
-
-#define NETARM_DMA2_BFR_DESCRPTOR_PTR (0x80)
-#define NETARM_DMA2_CONTROL (0x90)
-#define NETARM_DMA2_STATUS (0x94)
-
-#define NETARM_DMA3_BFR_DESCRPTOR_PTR (0xA0)
-#define NETARM_DMA3_CONTROL (0xB0)
-#define NETARM_DMA3_STATUS (0xB4)
-
-#define NETARM_DMA4_BFR_DESCRPTOR_PTR (0xC0)
-#define NETARM_DMA4_CONTROL (0xD0)
-#define NETARM_DMA4_STATUS (0xD4)
-
-#define NETARM_DMA5_BFR_DESCRPTOR_PTR (0xE0)
-#define NETARM_DMA5_CONTROL (0xF0)
-#define NETARM_DMA5_STATUS (0xF4)
-
-#define NETARM_DMA6_BFR_DESCRPTOR_PTR (0x100)
-#define NETARM_DMA6_CONTROL (0x110)
-#define NETARM_DMA6_STATUS (0x114)
-
-#define NETARM_DMA7_BFR_DESCRPTOR_PTR (0x120)
-#define NETARM_DMA7_CONTROL (0x130)
-#define NETARM_DMA7_STATUS (0x134)
-
-#define NETARM_DMA8_BFR_DESCRPTOR_PTR (0x140)
-#define NETARM_DMA8_CONTROL (0x150)
-#define NETARM_DMA8_STATUS (0x154)
-
-#define NETARM_DMA9_BFR_DESCRPTOR_PTR (0x160)
-#define NETARM_DMA9_CONTROL (0x170)
-#define NETARM_DMA9_STATUS (0x174)
-
-#define NETARM_DMA10_BFR_DESCRPTOR_PTR (0x180)
-#define NETARM_DMA10_CONTROL (0x190)
-#define NETARM_DMA10_STATUS (0x194)
-
-/* select bitfield defintions */
-
-/* DMA Control Register ( 0xFF90_0XX0 ) */
-
-#define NETARM_DMA_CTL_ENABLE (0x80000000)
-
-#define NETARM_DMA_CTL_ABORT (0x40000000)
-
-#define NETARM_DMA_CTL_BUS_100_PERCENT (0x00000000)
-#define NETARM_DMA_CTL_BUS_75_PERCENT (0x10000000)
-#define NETARM_DMA_CTL_BUS_50_PERCENT (0x20000000)
-#define NETARM_DMA_CTL_BUS_25_PERCENT (0x30000000)
-
-#define NETARM_DMA_CTL_BUS_MASK (0x30000000)
-
-#define NETARM_DMA_CTL_MODE_FB_TO_MEM (0x00000000)
-#define NETARM_DMA_CTL_MODE_FB_FROM_MEM (0x04000000)
-#define NETARM_DMA_CTL_MODE_MEM_TO_MEM (0x08000000)
-
-#define NETARM_DMA_CTL_BURST_NONE (0x00000000)
-#define NETARM_DMA_CTL_BURST_8_BYTE (0x01000000)
-#define NETARM_DMA_CTL_BURST_16_BYTE (0x02000000)
-
-#define NETARM_DMA_CTL_BURST_MASK (0x03000000)
-
-#define NETARM_DMA_CTL_SRC_INCREMENT (0x00200000)
-
-#define NETARM_DMA_CTL_DST_INCREMENT (0x00100000)
-
-/* these apply only to ext xfers on DMA 3 or 4 */
-
-#define NETARM_DMA_CTL_CH_3_4_REQ_EXT (0x00800000)
-
-#define NETARM_DMA_CTL_CH_3_4_DATA_32 (0x00000000)
-#define NETARM_DMA_CTL_CH_3_4_DATA_16 (0x00010000)
-#define NETARM_DMA_CTL_CH_3_4_DATA_8 (0x00020000)
-
-#define NETARM_DMA_CTL_STATE(X) ((X) & 0xFC00)
-#define NETARM_DMA_CTL_INDEX(X) ((X) & 0x03FF)
-
-/* DMA Status Register ( 0xFF90_0XX4 ) */
-
-#define NETARM_DMA_STAT_NC_INTPEN (0x80000000)
-#define NETARM_DMA_STAT_EC_INTPEN (0x40000000)
-#define NETARM_DMA_STAT_NR_INTPEN (0x20000000)
-#define NETARM_DMA_STAT_CA_INTPEN (0x10000000)
-#define NETARM_DMA_STAT_INTPEN_MASK (0xF0000000)
-
-#define NETARM_DMA_STAT_NC_INT_EN (0x00800000)
-#define NETARM_DMA_STAT_EC_INT_EN (0x00400000)
-#define NETARM_DMA_STAT_NR_INT_EN (0x00200000)
-#define NETARM_DMA_STAT_CA_INT_EN (0x00100000)
-#define NETARM_DMA_STAT_INT_EN_MASK (0x00F00000)
-
-#define NETARM_DMA_STAT_WRAP (0x00080000)
-#define NETARM_DMA_STAT_IDONE (0x00040000)
-#define NETARM_DMA_STAT_LAST (0x00020000)
-#define NETARM_DMA_STAT_FULL (0x00010000)
-
-#define NETARM_DMA_STAT_BUFLEN(X) ((X) & 0x7FFF)
-
-/* DMA Buffer Descriptor Word 0 bitfields. */
-
-#define NETARM_DMA_BD0_WRAP (0x80000000)
-#define NETARM_DMA_BD0_IDONE (0x40000000)
-#define NETARM_DMA_BD0_LAST (0x20000000)
-#define NETARM_DMA_BD0_BUFPTR_MASK (0x1FFFFFFF)
-
-/* DMA Buffer Descriptor Word 1 bitfields. */
-
-#define NETARM_DMA_BD1_STATUS_MASK (0xFFFF0000)
-#define NETARM_DMA_BD1_FULL (0x00008000)
-#define NETARM_DMA_BD1_BUFLEN_MASK (0x00007FFF)
-
-#ifndef __ASSEMBLER__
-
-typedef struct __NETARM_DMA_Buff_Desc_FlyBy
-{
- unsigned int word0;
- unsigned int word1;
-} NETARM_DMA_Buff_Desc_FlyBy, *pNETARM_DMA_Buff_Desc_FlyBy ;
-
-typedef struct __NETARM_DMA_Buff_Desc_M_to_M
-{
- unsigned int word0;
- unsigned int word1;
- unsigned int word2;
- unsigned int word3;
-} NETARM_DMA_Buff_Desc_M_to_M, *pNETARM_DMA_Buff_Desc_M_to_M ;
-
-#endif
-
-#endif
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_eni_module.h b/arch/arm/include/asm/arch-arm720t/netarm_eni_module.h
deleted file mode 100644
index 317b354..0000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_eni_module.h
+++ /dev/null
@@ -1,121 +0,0 @@
-/*
- * include/asm-armnommu/arch-netarm/netarm_eni_module.h
- *
- * Copyright (C) 2000 NETsilicon, Inc.
- * Copyright (C) 2000 WireSpeed Communications Corporation
- *
- * This software is copyrighted by WireSpeed. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall WireSpeed
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : David Smith
- */
-
-#ifndef __NETARM_ENI_MODULE_REGISTERS_H
-#define __NETARM_ENI_MODULE_REGISTERS_H
-
-/* ENI unit register offsets */
-
-/* #ifdef CONFIG_ARCH_NETARM */
-#define NETARM_ENI_MODULE_BASE (0xFFA00000)
-/* #endif / * CONFIG_ARCH_NETARM */
-
-#define get_eni_reg_addr(c) ((volatile unsigned int *)(NETARM_ENI_MODULE_BASE + (c)))
-#define get_eni_ctl_reg_addr(minor) \
- (get_eni_reg_addr(NETARM_ENI_1284_PORT1_CONTROL) + (minor))
-
-#define NETARM_ENI_GENERAL_CONTROL (0x00)
-#define NETARM_ENI_STATUS_CONTROL (0x04)
-#define NETARM_ENI_FIFO_MODE_DATA (0x08)
-
-#define NETARM_ENI_1284_PORT1_CONTROL (0x10)
-#define NETARM_ENI_1284_PORT2_CONTROL (0x14)
-#define NETARM_ENI_1284_PORT3_CONTROL (0x18)
-#define NETARM_ENI_1284_PORT4_CONTROL (0x1c)
-
-#define NETARM_ENI_1284_CHANNEL1_DATA (0x20)
-#define NETARM_ENI_1284_CHANNEL2_DATA (0x24)
-#define NETARM_ENI_1284_CHANNEL3_DATA (0x28)
-#define NETARM_ENI_1284_CHANNEL4_DATA (0x2c)
-
-#define NETARM_ENI_ENI_CONTROL (0x30)
-#define NETARM_ENI_ENI_PULSED_INTR (0x34)
-#define NETARM_ENI_ENI_SHARED_RAM_ADDR (0x38)
-#define NETARM_ENI_ENI_SHARED (0x3c)
-
-/* select bitfield defintions */
-
-/* General Control Register (0xFFA0_0000) */
-
-#define NETARM_ENI_GCR_ENIMODE_IEEE1284 (0x00000001)
-#define NETARM_ENI_GCR_ENIMODE_SHRAM16 (0x00000004)
-#define NETARM_ENI_GCR_ENIMODE_SHRAM8 (0x00000005)
-#define NETARM_ENI_GCR_ENIMODE_FIFO16 (0x00000006)
-#define NETARM_ENI_GCR_ENIMODE_FIFO8 (0x00000007)
-
-#define NETARM_ENI_GCR_ENIMODE_MASK (0x00000007)
-
-/* IEEE 1284 Port Control Registers 1-4 (0xFFA0_0010, 0xFFA0_0014,
- 0xFFA0_0018, 0xFFA0_001c) */
-
-#define NETARM_ENI_1284PC_PORT_ENABLE (0x80000000)
-#define NETARM_ENI_1284PC_DMA_ENABLE (0x40000000)
-#define NETARM_ENI_1284PC_OBE_INT_EN (0x20000000)
-#define NETARM_ENI_1284PC_ACK_INT_EN (0x10000000)
-#define NETARM_ENI_1284PC_ECP_MODE (0x08000000)
-#define NETARM_ENI_1284PC_LOOPBACK_MODE (0x04000000)
-
-#define NETARM_ENI_1284PC_STROBE_TIME0 (0x00000000) /* 0.5 uS */
-#define NETARM_ENI_1284PC_STROBE_TIME1 (0x01000000) /* 1.0 uS */
-#define NETARM_ENI_1284PC_STROBE_TIME2 (0x02000000) /* 5.0 uS */
-#define NETARM_ENI_1284PC_STROBE_TIME3 (0x03000000) /* 10.0 uS */
-#define NETARM_ENI_1284PC_STROBE_MASK (0x03000000)
-
-#define NETARM_ENI_1284PC_MAN_STROBE_EN (0x00800000)
-#define NETARM_ENI_1284PC_FAST_MODE (0x00400000)
-#define NETARM_ENI_1284PC_BIDIR_MODE (0x00200000)
-
-#define NETARM_ENI_1284PC_MAN_STROBE (0x00080000)
-#define NETARM_ENI_1284PC_AUTO_FEED (0x00040000)
-#define NETARM_ENI_1284PC_INIT (0x00020000)
-#define NETARM_ENI_1284PC_HSELECT (0x00010000)
-#define NETARM_ENI_1284PC_FE_INT_EN (0x00008000)
-#define NETARM_ENI_1284PC_EPP_MODE (0x00004000)
-#define NETARM_ENI_1284PC_IBR_INT_EN (0x00002000)
-#define NETARM_ENI_1284PC_IBR (0x00001000)
-
-#define NETARM_ENI_1284PC_RXFDB_1BYTE (0x00000400)
-#define NETARM_ENI_1284PC_RXFDB_2BYTE (0x00000800)
-#define NETARM_ENI_1284PC_RXFDB_3BYTE (0x00000c00)
-#define NETARM_ENI_1284PC_RXFDB_4BYTE (0x00000000)
-
-#define NETARM_ENI_1284PC_RBCC (0x00000200)
-#define NETARM_ENI_1284PC_RBCT (0x00000100)
-#define NETARM_ENI_1284PC_ACK (0x00000080)
-#define NETARM_ENI_1284PC_FIFO_E (0x00000040)
-#define NETARM_ENI_1284PC_OBE (0x00000020)
-#define NETARM_ENI_1284PC_ACK_INT (0x00000010)
-#define NETARM_ENI_1284PC_BUSY (0x00000008)
-#define NETARM_ENI_1284PC_PE (0x00000004)
-#define NETARM_ENI_1284PC_PSELECT (0x00000002)
-#define NETARM_ENI_1284PC_FAULT (0x00000001)
-
-#endif /* __NETARM_ENI_MODULE_REGISTERS_H */
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_eth_module.h b/arch/arm/include/asm/arch-arm720t/netarm_eth_module.h
deleted file mode 100644
index 8f2f369..0000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_eth_module.h
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * include/asm-armnommu/arch-netarm/netarm_eth_module.h
- *
- * Copyright (C) 2000 NETsilicon, Inc.
- * Copyright (C) 2000 WireSpeed Communications Corporation
- *
- * This software is copyrighted by WireSpeed. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall WireSpeed
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Jackie Smith Cashion
- * David Smith
- */
-
-#ifndef __NETARM_ETH_MODULE_REGISTERS_H
-#define __NETARM_ETH_MODULE_REGISTERS_H
-
-/* ETH unit register offsets */
-
-#define NETARM_ETH_MODULE_BASE (0xFF800000)
-
-#define get_eth_reg_addr(c) ((volatile unsigned int *)(NETARM_ETH_MODULE_BASE + (c)))
-
-#define NETARM_ETH_GEN_CTRL (0x000) /* Ethernet Gen Control Reg */
-#define NETARM_ETH_GEN_STAT (0x004) /* Ethernet Gen Status Reg */
-#define NETARM_ETH_FIFO_DAT1 (0x008) /* Fifo Data Reg 1 */
-#define NETARM_ETH_FIFO_DAT2 (0x00C) /* Fifo Data Reg 2 */
-#define NETARM_ETH_TX_STAT (0x010) /* Transmit Status Reg */
-#define NETARM_ETH_RX_STAT (0x014) /* Receive Status Reg */
-
-#define NETARM_ETH_MAC_CFG (0x400) /* MAC Configuration Reg */
-#define NETARM_ETH_PCS_CFG (0x408) /* PCS Configuration Reg */
-#define NETARM_ETH_STL_CFG (0x410) /* STL Configuration Reg */
-#define NETARM_ETH_B2B_IPG_GAP_TMR (0x440) /* Back-to-back IPG
- Gap Timer Reg */
-#define NETARM_ETH_NB2B_IPG_GAP_TMR (0x444) /* Non Back-to-back
- IPG Gap Timer Reg */
-#define NETARM_ETH_MII_CMD (0x540) /* MII (PHY) Command Reg */
-#define NETARM_ETH_MII_ADDR (0x544) /* MII Address Reg */
-#define NETARM_ETH_MII_WRITE (0x548) /* MII Write Data Reg */
-#define NETARM_ETH_MII_READ (0x54C) /* MII Read Data Reg */
-#define NETARM_ETH_MII_IND (0x550) /* MII Indicators Reg */
-#define NETARM_ETH_MIB_CRCEC (0x580) /* (MIB) CRC Error Counter */
-#define NETARM_ETH_MIB_AEC (0x584) /* Alignment Error Counter */
-#define NETARM_ETH_MIB_CEC (0x588) /* Code Error Counter */
-#define NETARM_ETH_MIB_LFC (0x58C) /* Long Frame Counter */
-#define NETARM_ETH_MIB_SFC (0x590) /* Short Frame Counter */
-#define NETARM_ETH_MIB_LCC (0x594) /* Late Collision Counter */
-#define NETARM_ETH_MIB_EDC (0x598) /* Excessive Deferral
- Counter */
-#define NETARM_ETH_MIB_MCC (0x59C) /* Maximum Collision Counter */
-#define NETARM_ETH_SAL_FILTER (0x5C0) /* SAL Station Address
- Filter Reg */
-#define NETARM_ETH_SAL_STATION_ADDR_1 (0x5C4) /* SAL Station Address
- Reg */
-#define NETARM_ETH_SAL_STATION_ADDR_2 (0x5C8)
-#define NETARM_ETH_SAL_STATION_ADDR_3 (0x5CC)
-#define NETARM_ETH_SAL_HASH_TBL_1 (0x5D0) /* SAL Multicast Hash Table*/
-#define NETARM_ETH_SAL_HASH_TBL_2 (0x5D4)
-#define NETARM_ETH_SAL_HASH_TBL_3 (0x5D8)
-#define NETARM_ETH_SAL_HASH_TBL_4 (0x5DC)
-
-/* select bitfield defintions */
-
-/* Ethernet General Control Register (0xFF80_0000) */
-
-#define NETARM_ETH_GCR_ERX (0x80000000) /* Enable Receive FIFO */
-#define NETARM_ETH_GCR_ERXDMA (0x40000000) /* Enable Receive DMA */
-#define NETARM_ETH_GCR_ETX (0x00800000) /* Enable Transmit FIFO */
-#define NETARM_ETH_GCR_ETXDMA (0x00400000) /* Enable Transmit DMA */
-#define NETARM_ETH_GCR_ETXWM_50 (0x00100000) /* Transmit FIFO Water
- Mark. Start transmit
- when FIFO is 50%
- full. */
-#define NETARM_ETH_GCR_PNA (0x00000400) /* pSOS pNA Buffer
- Descriptor Format */
-
-/* Ethernet General Status Register (0xFF80_0004) */
-
-#define NETARM_ETH_GST_RXFDB (0x30000000)
-#define NETARM_ETH_GST_RXREGR (0x08000000) /* Receive Register
- Ready */
-#define NETARM_ETH_GST_RXFIFOH (0x04000000)
-#define NETARM_ETH_GST_RXBR (0x02000000)
-#define NETARM_ETH_GST_RXSKIP (0x01000000)
-
-#define NETARM_ETH_GST_TXBC (0x00020000)
-
-
-/* Ethernet Transmit Status Register (0xFF80_0010) */
-
-#define NETARM_ETH_TXSTAT_TXOK (0x00008000)
-
-
-/* Ethernet Receive Status Register (0xFF80_0014) */
-
-#define NETARM_ETH_RXSTAT_SIZE (0xFFFF0000)
-#define NETARM_ETH_RXSTAT_RXOK (0x00002000)
-
-
-/* PCS Configuration Register (0xFF80_0408) */
-
-#define NETARM_ETH_PCSC_NOCFR (0x1) /* Disable Ciphering */
-#define NETARM_ETH_PCSC_ENJAB (0x2) /* Enable Jabber Protection */
-#define NETARM_ETH_PCSC_CLKS_25M (0x0) /* 25 MHz Clock Speed Select */
-#define NETARM_ETH_PCSC_CLKS_33M (0x4) /* 33 MHz Clock Speed Select */
-
-/* STL Configuration Register (0xFF80_0410) */
-
-#define NETARM_ETH_STLC_RXEN (0x2) /* Enable Packet Receiver */
-#define NETARM_ETH_STLC_AUTOZ (0x4) /* Auto Zero Statistics */
-
-/* MAC Configuration Register (0xFF80_0400) */
-
-#define NETARM_ETH_MACC_HUGEN (0x1) /* Enable Unlimited Transmit
- Frame Sizes */
-#define NETARM_ETH_MACC_PADEN (0x4) /* Automatic Pad Fill Frames
- to 64 Bytes */
-#define NETARM_ETH_MACC_CRCEN (0x8) /* Append CRC to Transmit
- Frames */
-
-/* MII (PHY) Command Register (0xFF80_0540) */
-
-#define NETARM_ETH_MIIC_RSTAT (0x1) /* Single Scan for Read Data */
-
-/* MII Indicators Register (0xFF80_0550) */
-
-#define NETARM_ETH_MIII_BUSY (0x1) /* MII I/F Busy with
- Read/Write */
-
-/* SAL Station Address Filter Register (0xFF80_05C0) */
-
-#define NETARM_ETH_SALF_PRO (0x8) /* Enable Promiscuous Mode */
-#define NETARM_ETH_SALF_PRM (0x4) /* Accept All Multicast
- Packets */
-#define NETARM_ETH_SALF_PRA (0x2) /* Accept Mulitcast Packets
- using Hash Table */
-#define NETARM_ETH_SALF_BROAD (0x1) /* Accept All Broadcast
- Packets */
-
-
-#endif /* __NETARM_GEN_MODULE_REGISTERS_H */
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_gen_module.h b/arch/arm/include/asm/arch-arm720t/netarm_gen_module.h
deleted file mode 100644
index 13656a3..0000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_gen_module.h
+++ /dev/null
@@ -1,186 +0,0 @@
-/*
- * include/asm-armnommu/arch-netarm/netarm_gen_module.h
- *
- * Copyright (C) 2005
- * Art Shipkowski, Videon Central, Inc., <art at videon-central.com>
- *
- * Copyright (C) 2000, 2001 NETsilicon, Inc.
- * Copyright (C) 2000, 2001 Red Hat, Inc.
- *
- * This software is copyrighted by Red Hat. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall Red Hat
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Joe deBlaquiere
- *
- * Modified to support NS7520 by Art Shipkowski.
- */
-
-#ifndef __NETARM_GEN_MODULE_REGISTERS_H
-#define __NETARM_GEN_MODULE_REGISTERS_H
-
-/* GEN unit register offsets */
-
-#define NETARM_GEN_MODULE_BASE (0xFFB00000)
-
-#define get_gen_reg_addr(c) ((volatile unsigned int *)(NETARM_GEN_MODULE_BASE + (c)))
-
-#define NETARM_GEN_SYSTEM_CONTROL (0x00)
-#define NETARM_GEN_STATUS_CONTROL (0x04)
-#define NETARM_GEN_PLL_CONTROL (0x08)
-#define NETARM_GEN_SOFTWARE_SERVICE (0x0c)
-
-#define NETARM_GEN_TIMER1_CONTROL (0x10)
-#define NETARM_GEN_TIMER1_STATUS (0x14)
-#define NETARM_GEN_TIMER2_CONTROL (0x18)
-#define NETARM_GEN_TIMER2_STATUS (0x1c)
-
-#define NETARM_GEN_PORTA (0x20)
-#ifndef CONFIG_NETARM_NS7520
-#define NETARM_GEN_PORTB (0x24)
-#endif
-#define NETARM_GEN_PORTC (0x28)
-
-#define NETARM_GEN_INTR_ENABLE (0x30)
-#define NETARM_GEN_INTR_ENABLE_SET (0x34)
-#define NETARM_GEN_INTR_ENABLE_CLR (0x38)
-#define NETARM_GEN_INTR_STATUS_EN (0x34)
-#define NETARM_GEN_INTR_STATUS_RAW (0x38)
-
-#define NETARM_GEN_CACHE_CONTROL1 (0x40)
-#define NETARM_GEN_CACHE_CONTROL2 (0x44)
-
-/* select bitfield definitions */
-
-/* System Control Register ( 0xFFB0_0000 ) */
-
-#define NETARM_GEN_SYS_CFG_LENDIAN (0x80000000)
-#define NETARM_GEN_SYS_CFG_BENDIAN (0x00000000)
-
-#define NETARM_GEN_SYS_CFG_BUSQRTR (0x00000000)
-#define NETARM_GEN_SYS_CFG_BUSHALF (0x20000000)
-#define NETARM_GEN_SYS_CFG_BUSFULL (0x40000000)
-
-#define NETARM_GEN_SYS_CFG_BCLK_DISABLE (0x10000000)
-
-#define NETARM_GEN_SYS_CFG_WDOG_EN (0x01000000)
-#define NETARM_GEN_SYS_CFG_WDOG_IRQ (0x00000000)
-#define NETARM_GEN_SYS_CFG_WDOG_FIQ (0x00400000)
-#define NETARM_GEN_SYS_CFG_WDOG_RST (0x00800000)
-#define NETARM_GEN_SYS_CFG_WDOG_24 (0x00000000)
-#define NETARM_GEN_SYS_CFG_WDOG_26 (0x00100000)
-#define NETARM_GEN_SYS_CFG_WDOG_28 (0x00200000)
-#define NETARM_GEN_SYS_CFG_WDOG_29 (0x00300000)
-
-#define NETARM_GEN_SYS_CFG_BUSMON_EN (0x00040000)
-#define NETARM_GEN_SYS_CFG_BUSMON_128 (0x00000000)
-#define NETARM_GEN_SYS_CFG_BUSMON_64 (0x00010000)
-#define NETARM_GEN_SYS_CFG_BUSMON_32 (0x00020000)
-#define NETARM_GEN_SYS_CFG_BUSMON_16 (0x00030000)
-
-#define NETARM_GEN_SYS_CFG_USER_EN (0x00008000)
-#define NETARM_GEN_SYS_CFG_BUSER_EN (0x00004000)
-
-#define NETARM_GEN_SYS_CFG_BUSARB_INT (0x00002000)
-#define NETARM_GEN_SYS_CFG_BUSARB_EXT (0x00000000)
-
-#define NETARM_GEN_SYS_CFG_DMATST (0x00001000)
-
-#define NETARM_GEN_SYS_CFG_TEALAST (0x00000800)
-
-#define NETARM_GEN_SYS_CFG_ALIGN_ABORT (0x00000400)
-
-#define NETARM_GEN_SYS_CFG_CACHE_EN (0x00000200)
-
-#define NETARM_GEN_SYS_CFG_WRI_BUF_EN (0x00000100)
-
-#define NETARM_GEN_SYS_CFG_CACHE_INIT (0x00000080)
-
-/* PLL Control Register ( 0xFFB0_0008 ) */
-
-#define NETARM_GEN_PLL_CTL_PLLCNT_MASK (0x0F000000)
-
-#define NETARM_GEN_PLL_CTL_PLLCNT(x) (((x)<<24) & \
- NETARM_GEN_PLL_CTL_PLLCNT_MASK)
-
-/* Defaults for POLTST and ICP Fields in PLL CTL */
-#define NETARM_GEN_PLL_CTL_OUTDIV(x) (x)
-#define NETARM_GEN_PLL_CTL_INDIV(x) ((x)<<6)
-#define NETARM_GEN_PLL_CTL_POLTST_DEF (0x00000E00)
-#define NETARM_GEN_PLL_CTL_ICP_DEF (0x0000003C)
-
-
-/* Software Service Register ( 0xFFB0_000C ) */
-
-#define NETARM_GEN_SW_SVC_RESETA (0x123)
-#define NETARM_GEN_SW_SVC_RESETB (0x321)
-
-/* PORT C Register ( 0xFFB0_0028 ) */
-
-#ifndef CONFIG_NETARM_NS7520
-#define NETARM_GEN_PORT_MODE(x) (((x)<<24) + (0xFF00))
-#define NETARM_GEN_PORT_DIR(x) (((x)<<16) + (0xFF00))
-#else
-#define NETARM_GEN_PORT_MODE(x) ((x)<<24)
-#define NETARM_GEN_PORT_DIR(x) ((x)<<16)
-#define NETARM_GEN_PORT_CSF(x) ((x)<<8)
-#endif
-
-/* Timer Registers ( 0xFFB0_0010 0xFFB0_0018 ) */
-
-#define NETARM_GEN_TCTL_ENABLE (0x80000000)
-#define NETARM_GEN_TCTL_INT_ENABLE (0x40000000)
-
-#define NETARM_GEN_TCTL_USE_IRQ (0x00000000)
-#define NETARM_GEN_TCTL_USE_FIQ (0x20000000)
-
-#define NETARM_GEN_TCTL_USE_PRESCALE (0x10000000)
-#define NETARM_GEN_TCTL_INIT_COUNT(x) ((x) & 0x1FF)
-
-#define NETARM_GEN_TSTAT_INTPEN (0x40000000)
-#if ~defined(CONFIG_NETARM_NS7520)
-#define NETARM_GEN_TSTAT_CTC_MASK (0x000001FF)
-#else
-#define NETARM_GEN_TSTAT_CTC_MASK (0x0FFFFFFF)
-#endif
-
-/* prescale to msecs conversion */
-
-#if !defined(CONFIG_NETARM_PLL_BYPASS)
-#define NETARM_GEN_TIMER_MSEC_P(x) ( ( ( 20480 ) * ( 0x1FF - ( (x) & \
- NETARM_GEN_TSTAT_CTC_MASK ) + \
- 1 ) ) / (NETARM_XTAL_FREQ/1000) )
-
-#define NETARM_GEN_TIMER_SET_HZ(x) ( ( ((NETARM_XTAL_FREQ/(20480*(x)))-1) & \
- NETARM_GEN_TSTAT_CTC_MASK ) | \
- NETARM_GEN_TCTL_USE_PRESCALE )
-
-#else
-#define NETARM_GEN_TIMER_MSEC_P(x) ( ( ( 4096 ) * ( 0x1FF - ( (x) & \
- NETARM_GEN_TSTAT_CTC_MASK ) + \
- 1 ) ) / (NETARM_XTAL_FREQ/1000) )
-
-#define NETARM_GEN_TIMER_SET_HZ(x) ( ( ((NETARM_XTAL_FREQ/(4096*(x)))-1) & \
- NETARM_GEN_TSTAT_CTC_MASK ) | \
- NETARM_GEN_TCTL_USE_PRESCALE )
-#endif
-
-#endif
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_mem_module.h b/arch/arm/include/asm/arch-arm720t/netarm_mem_module.h
deleted file mode 100644
index c650c3b..0000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_mem_module.h
+++ /dev/null
@@ -1,184 +0,0 @@
-/*
- * include/asm-armnommu/arch-netarm/netarm_mem_module.h
- *
- * Copyright (C) 2005
- * Art Shipkowski, Videon Central, Inc., <art at videon-central.com>
- *
- * Copyright (C) 2000, 2001 NETsilicon, Inc.
- * Copyright (C) 2000, 2001 Red Hat, Inc.
- *
- * This software is copyrighted by Red Hat. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall Red Hat
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Joe deBlaquiere
- *
- * Modified to support NS7520 by Art Shipkowski.
- */
-
-#ifndef __NETARM_MEM_MODULE_REGISTERS_H
-#define __NETARM_MEM_MODULE_REGISTERS_H
-
-/* GEN unit register offsets */
-
-#define NETARM_MEM_MODULE_BASE (0xFFC00000)
-
-#define NETARM_MEM_MODULE_CONFIG (0x00)
-#define NETARM_MEM_CS0_BASE_ADDR (0x10)
-#define NETARM_MEM_CS0_OPTIONS (0x14)
-#define NETARM_MEM_CS1_BASE_ADDR (0x20)
-#define NETARM_MEM_CS1_OPTIONS (0x24)
-#define NETARM_MEM_CS2_BASE_ADDR (0x30)
-#define NETARM_MEM_CS2_OPTIONS (0x34)
-#define NETARM_MEM_CS3_BASE_ADDR (0x40)
-#define NETARM_MEM_CS3_OPTIONS (0x44)
-#define NETARM_MEM_CS4_BASE_ADDR (0x50)
-#define NETARM_MEM_CS4_OPTIONS (0x54)
-
-/* select bitfield defintions */
-
-/* Module Configuration Register ( 0xFFC0_0000 ) */
-
-#define NETARM_MEM_CFG_REFR_COUNT_MASK (0xFF000000)
-#define NETARM_MEM_CFG_REFRESH_EN (0x00800000)
-
-#define NETARM_MEM_CFG_REFR_CYCLE_8CLKS (0x00000000)
-#define NETARM_MEM_CFG_REFR_CYCLE_6CLKS (0x00200000)
-#define NETARM_MEM_CFG_REFR_CYCLE_5CLKS (0x00400000)
-#define NETARM_MEM_CFG_REFR_CYCLE_4CLKS (0x00600000)
-
-#define NETARM_MEM_CFG_PORTC_AMUX (0x00100000)
-
-#define NETARM_MEM_CFG_A27_ADDR (0x00080000)
-#define NETARM_MEM_CFG_A27_CS0OE (0x00000000)
-
-#define NETARM_MEM_CFG_A26_ADDR (0x00040000)
-#define NETARM_MEM_CFG_A26_CS0WE (0x00000000)
-
-#define NETARM_MEM_CFG_A25_ADDR (0x00020000)
-#define NETARM_MEM_CFG_A25_BLAST (0x00000000)
-
-#define NETARM_MEM_CFG_PORTC_AMUX2 (0x00010000)
-
-
-/* range on this period is about 1 to 275 usec (with 18.432MHz clock) */
-/* the expression will round down, so make sure to reverse it to verify */
-/* it is what you want. period = [( count + 1 ) * 20] / Fcrystal */
-/* (note: Fxtal = Fcrystal/5, see HWRefGuide sections 8.2.5 and 11.3.2) */
-
-#define NETARM_MEM_REFR_PERIOD_USEC(p) (NETARM_MEM_CFG_REFR_COUNT_MASK & \
- (((((NETARM_XTAL_FREQ/(1000))*p)/(20000) \
- ) - (1) ) << (24)))
-
-#if 0
-/* range on this period is about 1 to 275 usec (with 18.432MHz clock) */
-/* the expression will round down, so make sure to reverse it toverify */
-/* it is what you want. period = [( count + 1 ) * 4] / Fxtal */
-
-#define NETARM_MEM_REFR_PERIOD_USEC(p) (NETARM_MEM_CFG_REFR_COUNT_MASK & \
- (((((NETARM_XTAL_FREQ/(1000))*p)/(4000) \
- ) - (1) ) << (24)))
-#endif
-
-/* Base Address Registers (0xFFC0_00X0) */
-
-#define NETARM_MEM_BAR_BASE_MASK (0xFFFFF000)
-
-/* macro to define base */
-
-#define NETARM_MEM_BAR_BASE(x) ((x) & NETARM_MEM_BAR_BASE_MASK)
-
-#define NETARM_MEM_BAR_DRAM_FP (0x00000000)
-#define NETARM_MEM_BAR_DRAM_EDO (0x00000100)
-#define NETARM_MEM_BAR_DRAM_SYNC (0x00000200)
-
-#define NETARM_MEM_BAR_DRAM_MUX_INT (0x00000000)
-#define NETARM_MEM_BAR_DRAM_MUX_EXT (0x00000080)
-
-#define NETARM_MEM_BAR_DRAM_MUX_BAL (0x00000000)
-#define NETARM_MEM_BAR_DRAM_MUX_UNBAL (0x00000020)
-
-#define NETARM_MEM_BAR_1BCLK_IDLE (0x00000010)
-
-#define NETARM_MEM_BAR_DRAM_SEL (0x00000008)
-
-#define NETARM_MEM_BAR_BURST_EN (0x00000004)
-
-#define NETARM_MEM_BAR_WRT_PROT (0x00000002)
-
-#define NETARM_MEM_BAR_VALID (0x00000001)
-
-/* Option Registers (0xFFC0_00X4) */
-
-/* macro to define which bits of the base are significant */
-
-#define NETARM_MEM_OPT_BASE_USE(x) ((x) & NETARM_MEM_BAR_BASE_MASK)
-
-#define NETARM_MEM_OPT_WAIT_MASK (0x00000F00)
-
-#define NETARM_MEM_OPT_WAIT_STATES(x) (((x) << 8 ) & NETARM_MEM_OPT_WAIT_MASK )
-
-#define NETARM_MEM_OPT_BCYC_1 (0x00000000)
-#define NETARM_MEM_OPT_BCYC_2 (0x00000040)
-#define NETARM_MEM_OPT_BCYC_3 (0x00000080)
-#define NETARM_MEM_OPT_BCYC_4 (0x000000C0)
-
-#define NETARM_MEM_OPT_BSIZE_2 (0x00000000)
-#define NETARM_MEM_OPT_BSIZE_4 (0x00000010)
-#define NETARM_MEM_OPT_BSIZE_8 (0x00000020)
-#define NETARM_MEM_OPT_BSIZE_16 (0x00000030)
-
-#define NETARM_MEM_OPT_32BIT (0x00000000)
-#define NETARM_MEM_OPT_16BIT (0x00000004)
-#define NETARM_MEM_OPT_8BIT (0x00000008)
-#define NETARM_MEM_OPT_32BIT_EXT_ACK (0x0000000C)
-
-#define NETARM_MEM_OPT_BUS_SIZE_MASK (0x0000000C)
-
-#define NETARM_MEM_OPT_READ_ASYNC (0x00000000)
-#define NETARM_MEM_OPT_READ_SYNC (0x00000002)
-
-#define NETARM_MEM_OPT_WRITE_ASYNC (0x00000000)
-#define NETARM_MEM_OPT_WRITE_SYNC (0x00000001)
-
-#ifdef CONFIG_NETARM_NS7520
-/* The NS7520 has a second options register for each chip select */
-#define NETARM_MEM_CS0_OPTIONS_B (0x18)
-#define NETARM_MEM_CS1_OPTIONS_B (0x28)
-#define NETARM_MEM_CS2_OPTIONS_B (0x38)
-#define NETARM_MEM_CS3_OPTIONS_B (0x48)
-#define NETARM_MEM_CS4_OPTIONS_B (0x58)
-
-/* Option B Registers (0xFFC0_00x8) */
-#define NETARM_MEM_OPTB_SYNC_1_STAGE (0x00000001)
-#define NETARM_MEM_OPTB_SYNC_2_STAGE (0x00000002)
-#define NETARM_MEM_OPTB_BCYC_PLUS0 (0x00000000)
-#define NETARM_MEM_OPTB_BCYC_PLUS4 (0x00000004)
-#define NETARM_MEM_OPTB_BCYC_PLUS8 (0x00000008)
-#define NETARM_MEM_OPTB_BCYC_PLUS12 (0x0000000C)
-
-#define NETARM_MEM_OPTB_WAIT_PLUS0 (0x00000000)
-#define NETARM_MEM_OPTB_WAIT_PLUS16 (0x00000010)
-#define NETARM_MEM_OPTB_WAIT_PLUS32 (0x00000020)
-#define NETARM_MEM_OPTB_WAIT_PLUS48 (0x00000030)
-#endif
-
-#endif
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_registers.h b/arch/arm/include/asm/arch-arm720t/netarm_registers.h
deleted file mode 100644
index fa88128..0000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_registers.h
+++ /dev/null
@@ -1,96 +0,0 @@
-/*
- * linux/include/asm-arm/arch-netarm/netarm_registers.h
- *
- * Copyright (C) 2005
- * Art Shipkowski, Videon Central, Inc., <art at videon-central.com>
- *
- * Copyright (C) 2000, 2001 NETsilicon, Inc.
- * Copyright (C) 2000, 2001 WireSpeed Communications Corporation
- *
- * This software is copyrighted by WireSpeed. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall WireSpeed
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Joe deBlaquiere
- *
- * Modified to support NS7520 by Art Shipkowski.
- */
-
-#ifndef __NET_ARM_REGISTERS_H
-#define __NET_ARM_REGISTERS_H
-
-#include <config.h>
-
-/* fundamental constants : */
-/* the input crystal/clock frequency ( in Hz ) */
-#define NETARM_XTAL_FREQ_25MHz (18432000)
-#define NETARM_XTAL_FREQ_33MHz (23698000)
-#define NETARM_XTAL_FREQ_48MHz (48000000)
-#define NETARM_XTAL_FREQ_55MHz (55000000)
-#define NETARM_XTAL_FREQ_EMLIN1 (20000000)
-
-/* the frequency of SYS_CLK */
-#if defined(CONFIG_NETARM_EMLIN)
-
-/* EMLIN board: 33 MHz (exp.) */
-#define NETARM_PLL_COUNT_VAL 6
-#define NETARM_XTAL_FREQ NETARM_XTAL_FREQ_25MHz
-
-#elif defined(CONFIG_NETARM_NET40_REV2)
-
-/* NET+40 Rev2 boards: 33 MHz (with NETARM_XTAL_FREQ_25MHz) */
-#define NETARM_PLL_COUNT_VAL 6
-#define NETARM_XTAL_FREQ NETARM_XTAL_FREQ_25MHz
-
-#elif defined(CONFIG_NETARM_NET40_REV4)
-
-/* NET+40 Rev4 boards with EDO must clock slower: 25 MHz (with
- NETARM_XTAL_FREQ_25MHz) 4 */
-#define NETARM_PLL_COUNT_VAL 4
-#define NETARM_XTAL_FREQ NETARM_XTAL_FREQ_25MHz
-
-#elif defined(CONFIG_NETARM_NET50)
-
-/* NET+50 boards: 40 MHz (with NETARM_XTAL_FREQ_25MHz) */
-#define NETARM_PLL_COUNT_VAL 8
-#define NETARM_XTAL_FREQ NETARM_XTAL_FREQ_25MHz
-
-#else /* CONFIG_NETARM_NS7520 */
-
-#define NETARM_PLL_COUNT_VAL 0
-
-#if defined(CONFIG_BOARD_UNC20)
-#define NETARM_XTAL_FREQ NETARM_XTAL_FREQ_48MHz
-#else
-#define NETARM_XTAL_FREQ NETARM_XTAL_FREQ_55MHz
-#endif
-
-#endif
-
-/* #include "arm_registers.h" */
-#include <asm/arch/netarm_gen_module.h>
-#include <asm/arch/netarm_mem_module.h>
-#include <asm/arch/netarm_ser_module.h>
-#include <asm/arch/netarm_eni_module.h>
-#include <asm/arch/netarm_dma_module.h>
-#include <asm/arch/netarm_eth_module.h>
-
-#endif
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_ser_module.h b/arch/arm/include/asm/arch-arm720t/netarm_ser_module.h
deleted file mode 100644
index 6fbae11..0000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_ser_module.h
+++ /dev/null
@@ -1,347 +0,0 @@
-/*
- * linux/include/asm-arm/arch-netarm/netarm_ser_module.h
- *
- * Copyright (C) 2000 NETsilicon, Inc.
- * Copyright (C) 2000 Red Hat, Inc.
- *
- * This software is copyrighted by Red Hat. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall Red Hat
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Joe deBlaquiere
- * Clark Williams
- */
-
-#ifndef __NETARM_SER_MODULE_REGISTERS_H
-#define __NETARM_SER_MODULE_REGISTERS_H
-
-#ifndef __ASSEMBLER__
-
-/* (--sub)#include "types.h" */
-
-/* serial channel control structure */
-typedef struct {
- u32 ctrl_a;
- u32 ctrl_b;
- u32 status_a;
- u32 bitrate;
- u32 fifo;
- u32 rx_buf_timer;
- u32 rx_char_timer;
- u32 rx_match;
- u32 rx_match_mask;
- u32 ctrl_c;
- u32 status_b;
- u32 status_c;
- u32 fifo_last;
- u32 unused[3];
-} netarm_serial_channel_t;
-
-#endif
-
-/* SER unit register offsets */
-
-/* #ifdef CONFIG_ARCH_NETARM */
-#define NETARM_SER_MODULE_BASE (0xFFD00000)
-/* #else */
-/* extern serial_channel_t netarm_dummy_registers[]; */
-/* #define NETARM_SER_MODULE_BASE (netarm_dummy_registers) */
-/* #ifndef NETARM_XTAL_FREQ */
-/* #define NETARM_XTAL_FREQ 18432000 */
-/* #endif */
-/* #endif */
-
-/* calculate the sysclk value from the pll setting */
-#define NETARM_PLLED_SYSCLK_FREQ (( NETARM_XTAL_FREQ / 5 ) * \
- ( NETARM_PLL_COUNT_VAL + 3 ))
-
-#define get_serial_channel(c) (&(((netarm_serial_channel_t *)NETARM_SER_MODULE_BASE)[c]))
-
-#define NETARM_SER_CH1_CTRL_A (0x00)
-#define NETARM_SER_CH1_CTRL_B (0x04)
-#define NETARM_SER_CH1_STATUS_A (0x08)
-#define NETARM_SER_CH1_BITRATE (0x0C)
-#define NETARM_SER_CH1_FIFO (0x10)
-#define NETARM_SER_CH1_RX_BUF_TMR (0x14)
-#define NETARM_SER_CH1_RX_CHAR_TMR (0x18)
-#define NETARM_SER_CH1_RX_MATCH (0x1c)
-#define NETARM_SER_CH1_RX_MATCH_MASK (0x20)
-#define NETARM_SER_CH1_CTRL_C (0x24)
-#define NETARM_SER_CH1_STATUS_B (0x28)
-#define NETARM_SER_CH1_STATUS_C (0x2c)
-#define NETARM_SER_CH1_FIFO_LAST (0x30)
-
-#define NETARM_SER_CH2_CTRL_A (0x40)
-#define NETARM_SER_CH2_CTRL_B (0x44)
-#define NETARM_SER_CH2_STATUS_A (0x48)
-#define NETARM_SER_CH2_BITRATE (0x4C)
-#define NETARM_SER_CH2_FIFO (0x50)
-#define NETARM_SER_CH2_RX_BUF_TMR (0x54)
-#define NETARM_SER_CH2_RX_CHAR_TMR (0x58)
-#define NETARM_SER_CH2_RX_MATCH (0x5c)
-#define NETARM_SER_CH2_RX_MATCH_MASK (0x60)
-#define NETARM_SER_CH2_CTRL_C (0x64)
-#define NETARM_SER_CH2_STATUS_B (0x68)
-#define NETARM_SER_CH2_STATUS_C (0x6c)
-#define NETARM_SER_CH2_FIFO_LAST (0x70)
-
-/* select bitfield defintions */
-
-/* Control Register A */
-
-#define NETARM_SER_CTLA_ENABLE (0x80000000)
-#define NETARM_SER_CTLA_BRK (0x40000000)
-
-#define NETARM_SER_CTLA_STICKP (0x20000000)
-
-#define NETARM_SER_CTLA_P_EVEN (0x18000000)
-#define NETARM_SER_CTLA_P_ODD (0x08000000)
-#define NETARM_SER_CTLA_P_NONE (0x00000000)
-
-/* if you read the errata, you will find that the STOP bits don't work right */
-#define NETARM_SER_CTLA_2STOP (0x00000000)
-#define NETARM_SER_CTLA_3STOP (0x04000000)
-
-#define NETARM_SER_CTLA_5BITS (0x00000000)
-#define NETARM_SER_CTLA_6BITS (0x01000000)
-#define NETARM_SER_CTLA_7BITS (0x02000000)
-#define NETARM_SER_CTLA_8BITS (0x03000000)
-
-#define NETARM_SER_CTLA_CTSTX (0x00800000)
-#define NETARM_SER_CTLA_RTSRX (0x00400000)
-
-#define NETARM_SER_CTLA_LOOP_REM (0x00200000)
-#define NETARM_SER_CTLA_LOOP_LOC (0x00100000)
-
-#define NETARM_SER_CTLA_GPIO2 (0x00080000)
-#define NETARM_SER_CTLA_GPIO1 (0x00040000)
-
-#define NETARM_SER_CTLA_DTR_EN (0x00020000)
-#define NETARM_SER_CTLA_RTS_EN (0x00010000)
-
-#define NETARM_SER_CTLA_IE_RX_BRK (0x00008000)
-#define NETARM_SER_CTLA_IE_RX_FRMERR (0x00004000)
-#define NETARM_SER_CTLA_IE_RX_PARERR (0x00002000)
-#define NETARM_SER_CTLA_IE_RX_OVERRUN (0x00001000)
-#define NETARM_SER_CTLA_IE_RX_RDY (0x00000800)
-#define NETARM_SER_CTLA_IE_RX_HALF (0x00000400)
-#define NETARM_SER_CTLA_IE_RX_FULL (0x00000200)
-#define NETARM_SER_CTLA_IE_RX_DMAEN (0x00000100)
-#define NETARM_SER_CTLA_IE_RX_DCD (0x00000080)
-#define NETARM_SER_CTLA_IE_RX_RI (0x00000040)
-#define NETARM_SER_CTLA_IE_RX_DSR (0x00000020)
-
-#define NETARM_SER_CTLA_IE_RX_ALL (NETARM_SER_CTLA_IE_RX_BRK \
- |NETARM_SER_CTLA_IE_RX_FRMERR \
- |NETARM_SER_CTLA_IE_RX_PARERR \
- |NETARM_SER_CTLA_IE_RX_OVERRUN \
- |NETARM_SER_CTLA_IE_RX_RDY \
- |NETARM_SER_CTLA_IE_RX_HALF \
- |NETARM_SER_CTLA_IE_RX_FULL \
- |NETARM_SER_CTLA_IE_RX_DMAEN \
- |NETARM_SER_CTLA_IE_RX_DCD \
- |NETARM_SER_CTLA_IE_RX_RI \
- |NETARM_SER_CTLA_IE_RX_DSR)
-
-#define NETARM_SER_CTLA_IE_TX_CTS (0x00000010)
-#define NETARM_SER_CTLA_IE_TX_EMPTY (0x00000008)
-#define NETARM_SER_CTLA_IE_TX_HALF (0x00000004)
-#define NETARM_SER_CTLA_IE_TX_FULL (0x00000002)
-#define NETARM_SER_CTLA_IE_TX_DMAEN (0x00000001)
-
-#define NETARM_SER_CTLA_IE_TX_ALL (NETARM_SER_CTLA_IE_TX_CTS \
- |NETARM_SER_CTLA_IE_TX_EMPTY \
- |NETARM_SER_CTLA_IE_TX_HALF \
- |NETARM_SER_CTLA_IE_TX_FULL \
- |NETARM_SER_CTLA_IE_TX_DMAEN)
-
-/* Control Register B */
-
-#define NETARM_SER_CTLB_MATCH1_EN (0x80000000)
-#define NETARM_SER_CTLB_MATCH2_EN (0x40000000)
-#define NETARM_SER_CTLB_MATCH3_EN (0x20000000)
-#define NETARM_SER_CTLB_MATCH4_EN (0x10000000)
-
-#define NETARM_SER_CTLB_RBGT_EN (0x08000000)
-#define NETARM_SER_CTLB_RCGT_EN (0x04000000)
-
-#define NETARM_SER_CTLB_UART_MODE (0x00000000)
-#define NETARM_SER_CTLB_HDLC_MODE (0x00100000)
-#define NETARM_SER_CTLB_SPI_MAS_MODE (0x00200000)
-#define NETARM_SER_CTLB_SPI_SLV_MODE (0x00300000)
-
-#define NETARM_SER_CTLB_REV_BIT_ORDER (0x00080000)
-
-#define NETARM_SER_CTLB_MAM1 (0x00040000)
-#define NETARM_SER_CTLB_MAM2 (0x00020000)
-
-/* Status Register A */
-
-#define NETARM_SER_STATA_MATCH1 (0x80000000)
-#define NETARM_SER_STATA_MATCH2 (0x40000000)
-#define NETARM_SER_STATA_MATCH3 (0x20000000)
-#define NETARM_SER_STATA_MATCH4 (0x10000000)
-
-#define NETARM_SER_STATA_BGAP (0x80000000)
-#define NETARM_SER_STATA_CGAP (0x40000000)
-
-#define NETARM_SER_STATA_RX_1B (0x00100000)
-#define NETARM_SER_STATA_RX_2B (0x00200000)
-#define NETARM_SER_STATA_RX_3B (0x00300000)
-#define NETARM_SER_STATA_RX_4B (0x00000000)
-
-/* downshifted values */
-
-#define NETARM_SER_STATA_RXFDB_1BYTES (0x001)
-#define NETARM_SER_STATA_RXFDB_2BYTES (0x002)
-#define NETARM_SER_STATA_RXFDB_3BYTES (0x003)
-#define NETARM_SER_STATA_RXFDB_4BYTES (0x000)
-
-#define NETARM_SER_STATA_RXFDB_MASK (0x00300000)
-#define NETARM_SER_STATA_RXFDB(x) (((x) & NETARM_SER_STATA_RXFDB_MASK) \
- >> 20)
-
-#define NETARM_SER_STATA_DCD (0x00080000)
-#define NETARM_SER_STATA_RI (0x00040000)
-#define NETARM_SER_STATA_DSR (0x00020000)
-#define NETARM_SER_STATA_CTS (0x00010000)
-
-#define NETARM_SER_STATA_RX_BRK (0x00008000)
-#define NETARM_SER_STATA_RX_FRMERR (0x00004000)
-#define NETARM_SER_STATA_RX_PARERR (0x00002000)
-#define NETARM_SER_STATA_RX_OVERRUN (0x00001000)
-#define NETARM_SER_STATA_RX_RDY (0x00000800)
-#define NETARM_SER_STATA_RX_HALF (0x00000400)
-#define NETARM_SER_STATA_RX_CLOSED (0x00000200)
-#define NETARM_SER_STATA_RX_FULL (0x00000100)
-#define NETARM_SER_STATA_RX_DCD (0x00000080)
-#define NETARM_SER_STATA_RX_RI (0x00000040)
-#define NETARM_SER_STATA_RX_DSR (0x00000020)
-
-#define NETARM_SER_STATA_TX_CTS (0x00000010)
-#define NETARM_SER_STATA_TX_RDY (0x00000008)
-#define NETARM_SER_STATA_TX_HALF (0x00000004)
-#define NETARM_SER_STATA_TX_FULL (0x00000002)
-#define NETARM_SER_STATA_TX_DMAEN (0x00000001)
-
-/* you have to clear all receive signals to get the fifo to move forward */
-#define NETARM_SER_STATA_CLR_ALL (NETARM_SER_STATA_RX_BRK | \
- NETARM_SER_STATA_RX_FRMERR | \
- NETARM_SER_STATA_RX_PARERR | \
- NETARM_SER_STATA_RX_OVERRUN | \
- NETARM_SER_STATA_RX_HALF | \
- NETARM_SER_STATA_RX_CLOSED | \
- NETARM_SER_STATA_RX_FULL | \
- NETARM_SER_STATA_RX_DCD | \
- NETARM_SER_STATA_RX_RI | \
- NETARM_SER_STATA_RX_DSR | \
- NETARM_SER_STATA_TX_CTS )
-
-/* Bit Rate Registers */
-
-#define NETARM_SER_BR_EN (0x80000000)
-#define NETARM_SER_BR_TMODE (0x40000000)
-
-#define NETARM_SER_BR_RX_CLK_INT (0x00000000)
-#define NETARM_SER_BR_RX_CLK_EXT (0x20000000)
-#define NETARM_SER_BR_TX_CLK_INT (0x00000000)
-#define NETARM_SER_BR_TX_CLK_EXT (0x10000000)
-
-#define NETARM_SER_BR_RX_CLK_DRV (0x08000000)
-#define NETARM_SER_BR_TX_CLK_DRV (0x04000000)
-
-#define NETARM_SER_BR_CLK_EXT_5 (0x00000000)
-#define NETARM_SER_BR_CLK_SYSTEM (0x01000000)
-#define NETARM_SER_BR_CLK_OUT1A (0x02000000)
-#define NETARM_SER_BR_CLK_OUT2A (0x03000000)
-
-#define NETARM_SER_BR_TX_CLK_INV (0x00800000)
-#define NETARM_SER_BR_RX_CLK_INV (0x00400000)
-
-/* complete settings assuming system clock input is 18MHz */
-
-#define NETARM_SER_BR_MASK (0x000007FF)
-
-/* bit rate determined from equation Fbr = Fxtal / [ 10 * ( N + 1 ) ] */
-/* from section 7.5.4 of HW Ref Guide */
-
-/* #ifdef CONFIG_NETARM_PLL_BYPASS */
-#define NETARM_SER_BR_X16(x) ( NETARM_SER_BR_EN | \
- NETARM_SER_BR_RX_CLK_INT | \
- NETARM_SER_BR_TX_CLK_INT | \
- NETARM_SER_BR_CLK_EXT_5 | \
- ( ( ( ( NETARM_XTAL_FREQ / \
- ( x * 10 ) ) - 1 ) / 16 ) & \
- NETARM_SER_BR_MASK ) )
-/*
-#else
-#define NETARM_SER_BR_X16(x) ( NETARM_SER_BR_EN | \
- NETARM_SER_BR_RX_CLK_INT | \
- NETARM_SER_BR_TX_CLK_INT | \
- NETARM_SER_BR_CLK_SYSTEM | \
- ( ( ( ( NETARM_PLLED_SYSCLK_FREQ / \
- ( x * 2 ) ) - 1 ) / 16 ) & \
- NETARM_SER_BR_MASK ) )
-#endif
-*/
-
-/* Receive Buffer Gap Timer */
-
-#define NETARM_SER_RX_GAP_TIMER_EN (0x80000000)
-#define NETARM_SER_RX_GAP_MASK (0x00003FFF)
-
-/* rx gap is a function of bit rate x */
-
-/* #ifdef CONFIG_NETARM_PLL_BYPASS */
-#define NETARM_SER_RXGAP(x) ( NETARM_SER_RX_GAP_TIMER_EN | \
- ( ( ( ( 10 * NETARM_XTAL_FREQ ) / \
- ( x * 5 * 512 ) ) - 1 ) & \
- NETARM_SER_RX_GAP_MASK ) )
-/*
-#else
-#define NETARM_SER_RXGAP(x) ( NETARM_SER_RX_GAP_TIMER_EN | \
- ( ( ( ( 2 * NETARM_PLLED_SYSCLK_FREQ ) / \
- ( x * 512 ) ) - 1 ) & \
- NETARM_SER_RX_GAP_MASK ) )
-#endif
-*/
-
-#if 0
-#define NETARM_SER_RXGAP(x) ( NETARM_SER_RX_GAP_TIMER_EN | \
- ( ( ( ( 2 * NETARM_PLLED_SYSCLK_FREQ ) / \
- ( x * 5 * 512 ) ) - 1 ) & \
- NETARM_SER_RX_GAP_MASK ) )
-#define NETARM_SER_RXGAP(x) ( NETARM_SER_RX_GAP_TIMER_EN | \
- ( ( ( ( 10 * NETARM_XTAL_FREQ ) / \
- ( x * 512 ) ) - 1 ) & \
- NETARM_SER_RX_GAP_MASK ) )
-#endif
-
-#define MIN_BAUD_RATE 600
-#define MAX_BAUD_RATE 115200
-
-/* the default BAUD rate for the BOOTLOADER, there is a separate */
-/* setting in the serial driver <arch/armnommu/drivers/char/serial-netarm.h> */
-#define DEFAULT_BAUD_RATE 9600
-#define NETARM_SER_FIFO_SIZE 32
-#define MIN_GAP 0
-
-#endif
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 430f90c..9b6a557 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -59,7 +59,6 @@ COBJS-$(CONFIG_MVGBE) += mvgbe.o
COBJS-$(CONFIG_NATSEMI) += natsemi.o
COBJS-$(CONFIG_DRIVER_NE2000) += ne2000.o ne2000_base.o
COBJS-$(CONFIG_DRIVER_AX88796L) += ax88796.o ne2000_base.o
-COBJS-$(CONFIG_DRIVER_NETARMETH) += netarm_eth.o
COBJS-$(CONFIG_NETCONSOLE) += netconsole.o
COBJS-$(CONFIG_NS8382X) += ns8382x.o
COBJS-$(CONFIG_PCNET) += pcnet.o
diff --git a/drivers/net/netarm_eth.c b/drivers/net/netarm_eth.c
deleted file mode 100644
index 325f16c..0000000
--- a/drivers/net/netarm_eth.c
+++ /dev/null
@@ -1,352 +0,0 @@
-/*
- * Copyright (C) 2004 IMMS gGmbH <www.imms.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * author(s): Thomas Elste, <info at elste.org>
- * (some parts derived from uCLinux Netarm Ethernet Driver)
- */
-
-
-#include <common.h>
-#include <command.h>
-#include <net.h>
-#include "netarm_eth.h"
-#include <asm/arch/netarm_registers.h>
-
-static int na_mii_poll_busy (void);
-
-static void na_get_mac_addr (void)
-{
- unsigned short p[3];
- char *m_addr;
- char ethaddr[20];
-
- m_addr = (char *) p;
-
- p[0] = (unsigned short) GET_EADDR (NETARM_ETH_SAL_STATION_ADDR_1);
- p[1] = (unsigned short) GET_EADDR (NETARM_ETH_SAL_STATION_ADDR_2);
- p[2] = (unsigned short) GET_EADDR (NETARM_ETH_SAL_STATION_ADDR_3);
-
- sprintf (ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X",
- m_addr[0], m_addr[1],
- m_addr[2], m_addr[3], m_addr[4], m_addr[5]);
-
- printf ("HW-MAC Address: %s\n", ethaddr);
-
- /* set env, todo: check if already an adress is set */
- setenv ("ethaddr", ethaddr);
-}
-
-static void na_mii_write (int reg, int value)
-{
- int mii_addr;
-
- /* Select register */
- mii_addr = CONFIG_SYS_ETH_PHY_ADDR + reg;
- SET_EADDR (NETARM_ETH_MII_ADDR, mii_addr);
- /* Write value */
- SET_EADDR (NETARM_ETH_MII_WRITE, value);
- na_mii_poll_busy ();
-}
-
-static unsigned int na_mii_read (int reg)
-{
- int mii_addr, val;
-
- /* Select register */
- mii_addr = CONFIG_SYS_ETH_PHY_ADDR + reg;
- SET_EADDR (NETARM_ETH_MII_ADDR, mii_addr);
- /* do one management cycle */
- SET_EADDR (NETARM_ETH_MII_CMD,
- GET_EADDR (NETARM_ETH_MII_CMD) | NETARM_ETH_MIIC_RSTAT);
- na_mii_poll_busy ();
- /* Return read value */
- val = GET_EADDR (NETARM_ETH_MII_READ);
- return val;
-}
-
-static int na_mii_poll_busy (void)
-{
- ulong start;
- /* arm simple, non interrupt dependent timer */
- start = get_timer(0));
- while (get_timer(start) < NA_MII_POLL_BUSY_DELAY) {
- if (!(GET_EADDR (NETARM_ETH_MII_IND) & NETARM_ETH_MIII_BUSY)) {
- return 1;
- }
- }
- printf ("na_mii_busy timeout\n");
- return (0);
-}
-
-static int na_mii_identify_phy (void)
-{
- int id_reg_a = 0;
-
- /* get phy id register */
- id_reg_a = na_mii_read (MII_PHY_ID);
-
- if (id_reg_a == 0x0043) {
- /* This must be an Enable or a Lucent LU3X31 PHY chip */
- return 1;
- } else if (id_reg_a == 0x0013) {
- /* it is an Intel LXT971A */
- return 1;
- }
- return (0);
-}
-
-static int na_mii_negotiate (void)
-{
- int i = 0;
-
- /* Enable auto-negotiation */
- na_mii_write (MII_PHY_AUTONEGADV, 0x01e1);
- /* FIXME: 0x01E1 is 100Mb half and full duplex, 0x0061 is 10Mb only */
- /* Restart auto-negotiation */
- na_mii_write (MII_PHY_CONTROL, 0x1200);
-
- /* status register is 0xffff after setting the autoneg restart bit */
- while (na_mii_read (MII_PHY_STATUS) == 0xffff) {
- i++;
- }
-
- /* na_mii_read uses the timer already, so we can't use it again for
- timeout checking.
- Instead we just try some times.
- */
- for (i = 0; i < 40000; i++) {
- if ((na_mii_read (MII_PHY_STATUS) & 0x0024) == 0x0024) {
- return 0;
- }
- }
- /*
- printf("*Warning* autonegotiation timeout, status: 0x%x\n",na_mii_read(MII_PHY_STATUS));
- */
- return (1);
-}
-
-static unsigned int na_mii_check_speed (void)
-{
- unsigned int status;
-
- /* Read Status register */
- status = na_mii_read (MII_PHY_STATUS);
- /* Check link status. If 0, default to 100 Mbps. */
- if ((status & 0x0004) == 0) {
- printf ("*Warning* no link detected, set default speed to 100Mbs\n");
- return 1;
- } else {
- if ((na_mii_read (17) & 0x4000) != 0) {
- printf ("100Mbs link detected\n");
- return 1;
- } else {
- printf ("10Mbs link detected\n");
- return 0;
- }
- }
- return 0;
-}
-
-static int reset_eth (void)
-{
- int pt;
- ulong start;
-
- na_get_mac_addr ();
- pt = na_mii_identify_phy ();
-
- /* reset the phy */
- na_mii_write (MII_PHY_CONTROL, 0x8000);
- start = get_timer(0);
- while (get_timer(start) < NA_MII_NEGOTIATE_DELAY) {
- if ((na_mii_read (MII_PHY_STATUS) & 0x8000) == 0) {
- break;
- }
- }
- if (get_timer(start) >= NA_MII_NEGOTIATE_DELAY)
- printf ("phy reset timeout\n");
-
- /* set the PCS reg */
- SET_EADDR (NETARM_ETH_PCS_CFG, NETARM_ETH_PCSC_CLKS_25M |
- NETARM_ETH_PCSC_ENJAB | NETARM_ETH_PCSC_NOCFR);
-
- na_mii_negotiate ();
- na_mii_check_speed ();
-
- /* Delay 10 millisecond. (Maybe this should be 1 second.) */
- udelay (10000);
-
- /* Turn receive on.
- Enable statistics register autozero on read.
- Do not insert MAC address on transmit.
- Do not enable special test modes. */
- SET_EADDR (NETARM_ETH_STL_CFG,
- (NETARM_ETH_STLC_AUTOZ | NETARM_ETH_STLC_RXEN));
-
- /* Set the inter-packet gap delay to 0.96us for MII.
- The NET+ARM H/W Reference Guide indicates that the Back-to-back IPG
- Gap Timer Register should be set to 0x15 and the Non Back-to-back IPG
- Gap Timer Register should be set to 0x00000C12 for the MII PHY. */
- SET_EADDR (NETARM_ETH_B2B_IPG_GAP_TMR, 0x15);
- SET_EADDR (NETARM_ETH_NB2B_IPG_GAP_TMR, 0x00000C12);
-
- /* Add CRC to end of packets.
- Pad packets to minimum length of 64 bytes.
- Allow unlimited length transmit packets.
- Receive all broadcast packets.
- NOTE: Multicast addressing is NOT enabled here currently. */
- SET_EADDR (NETARM_ETH_MAC_CFG,
- (NETARM_ETH_MACC_CRCEN |
- NETARM_ETH_MACC_PADEN | NETARM_ETH_MACC_HUGEN));
- SET_EADDR (NETARM_ETH_SAL_FILTER, NETARM_ETH_SALF_BROAD);
-
- /* enable fifos */
- SET_EADDR (NETARM_ETH_GEN_CTRL,
- (NETARM_ETH_GCR_ERX | NETARM_ETH_GCR_ETX));
-
- return (0);
-}
-
-
-extern int eth_init (bd_t * bd)
-{
- reset_eth ();
- return 0;
-}
-
-extern void eth_halt (void)
-{
- SET_EADDR (NETARM_ETH_GEN_CTRL, 0);
-}
-
-/* Get a data block via Ethernet */
-extern int eth_rx (void)
-{
- int i;
- unsigned short rxlen;
- unsigned int *addr;
- unsigned int rxstatus, lastrxlen;
- char *pa;
-
- /* RXBR is 1, data block was received */
- if ((GET_EADDR (NETARM_ETH_GEN_STAT) & NETARM_ETH_GST_RXBR) == 0)
- return 0;
-
- /* get status register and the length of received block */
- rxstatus = GET_EADDR (NETARM_ETH_RX_STAT);
- rxlen = (rxstatus & NETARM_ETH_RXSTAT_SIZE) >> 16;
-
- if (rxlen == 0)
- return 0;
-
- /* clear RXBR to make fifo available */
- SET_EADDR (NETARM_ETH_GEN_STAT,
- GET_EADDR (NETARM_ETH_GEN_STAT) & ~NETARM_ETH_GST_RXBR);
-
- /* clear TXBC to make fifo available */
- /* According to NETARM50 data manual you just have to clear
- RXBR but that has no effect. Only after clearing TXBC the
- Fifo becomes readable. */
- SET_EADDR (NETARM_ETH_GEN_STAT,
- GET_EADDR (NETARM_ETH_GEN_STAT) & ~NETARM_ETH_GST_TXBC);
-
- addr = (unsigned int *) NetRxPackets[0];
- pa = (char *) NetRxPackets[0];
-
- /* read the fifo */
- for (i = 0; i < rxlen / 4; i++) {
- *addr = GET_EADDR (NETARM_ETH_FIFO_DAT1);
- addr++;
- }
-
- if (GET_EADDR (NETARM_ETH_GEN_STAT) & NETARM_ETH_GST_RXREGR) {
- /* RXFDB indicates wether the last word is 1,2,3 or 4 bytes long */
- lastrxlen =
- (GET_EADDR (NETARM_ETH_GEN_STAT) &
- NETARM_ETH_GST_RXFDB) >> 28;
- *addr = GET_EADDR (NETARM_ETH_FIFO_DAT1);
- switch (lastrxlen) {
- case 1:
- *addr &= 0xff000000;
- break;
- case 2:
- *addr &= 0xffff0000;
- break;
- case 3:
- *addr &= 0xffffff00;
- break;
- }
- }
-
- /* Pass the packet up to the protocol layers. */
- NetReceive (NetRxPackets[0], rxlen);
-
- return rxlen;
-}
-
-/* Send a data block via Ethernet. */
-extern int eth_send(void *packet, int length)
-{
- int i, length32;
- char *pa;
- unsigned int *pa32, lastp = 0, rest;
-
- pa = (char *) packet;
- pa32 = (unsigned int *) packet;
- length32 = length / 4;
- rest = length % 4;
-
- /* make sure there's no garbage in the last word */
- switch (rest) {
- case 0:
- lastp = pa32[length32];
- length32--;
- break;
- case 1:
- lastp = pa32[length32] & 0x000000ff;
- break;
- case 2:
- lastp = pa32[length32] & 0x0000ffff;
- break;
- case 3:
- lastp = pa32[length32] & 0x00ffffff;
- break;
- }
-
- /* write to the fifo */
- for (i = 0; i < length32; i++)
- SET_EADDR (NETARM_ETH_FIFO_DAT1, pa32[i]);
-
- /* the last word is written to an extra register, this
- starts the transmission */
- SET_EADDR (NETARM_ETH_FIFO_DAT2, lastp);
-
- /* NETARM_ETH_TXSTAT_TXOK should be checked, to know if the transmission
- went fine. But we can't use the timer for a timeout loop because
- of it is used already in upper layers. So we just try some times. */
- i = 0;
- while (i < 50000) {
- if ((GET_EADDR (NETARM_ETH_TX_STAT) & NETARM_ETH_TXSTAT_TXOK)
- == NETARM_ETH_TXSTAT_TXOK)
- return 0;
- i++;
- }
-
- printf ("eth_send timeout\n");
- return 1;
-}
diff --git a/drivers/net/netarm_eth.h b/drivers/net/netarm_eth.h
deleted file mode 100644
index 8edab82..0000000
--- a/drivers/net/netarm_eth.h
+++ /dev/null
@@ -1,42 +0,0 @@
-/*
- * Copyright (C) 2003 IMMS gGmbH <www.imms.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * author(s): Thomas Elste, <info at elste.org>
- */
-
-#include <asm/types.h>
-#include <config.h>
-
-#ifdef CONFIG_DRIVER_NETARMETH
-
-#define SET_EADDR(ad,val) *(volatile unsigned int*)(ad + NETARM_ETH_MODULE_BASE) = val
-#define GET_EADDR(ad) (*(volatile unsigned int*)(ad + NETARM_ETH_MODULE_BASE))
-
-#define NA_MII_POLL_BUSY_DELAY 900
-
-/* MII negotiation timeout value
- 500 jiffies = 5 seconds */
-#define NA_MII_NEGOTIATE_DELAY 30
-
-/* Registers in the physical layer chip */
-#define MII_PHY_CONTROL 0
-#define MII_PHY_STATUS 1
-#define MII_PHY_ID 2
-#define MII_PHY_AUTONEGADV 4
-
-#endif /* CONFIG_DRIVER_NETARMETH */
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index fb0969c..5f0e714 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -44,7 +44,6 @@ COBJS-$(CONFIG_KS8695_SERIAL) += serial_ks8695.o
COBJS-$(CONFIG_LH7A40X_SERIAL) += serial_lh7a40x.o
COBJS-$(CONFIG_MAX3100_SERIAL) += serial_max3100.o
COBJS-$(CONFIG_MXC_UART) += serial_mxc.o
-COBJS-$(CONFIG_NETARM_SERIAL) += serial_netarm.o
COBJS-$(CONFIG_PL010_SERIAL) += serial_pl01x.o
COBJS-$(CONFIG_PL011_SERIAL) += serial_pl01x.o
COBJS-$(CONFIG_PXA_SERIAL) += serial_pxa.o
diff --git a/drivers/serial/serial_netarm.c b/drivers/serial/serial_netarm.c
deleted file mode 100644
index d04790d..0000000
--- a/drivers/serial/serial_netarm.c
+++ /dev/null
@@ -1,190 +0,0 @@
-/*
- * Serial Port stuff - taken from Linux
- *
- * (C) Copyright 2002
- * MAZeT GmbH <www.mazet.de>
- * Stephan Linz <linz at mazet.de>, <linz at li-pro.net>
- *
- * (c) 2004
- * IMMS gGmbH <www.imms.de>
- * Thomas Elste <info at elste.org>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- */
-
-#include <common.h>
-#include <asm/hardware.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define PORTA (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_PORTA))
-#if !defined(CONFIG_NETARM_NS7520)
-#define PORTB (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_PORTB))
-#else
-#define PORTC (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_PORTC))
-#endif
-
-/* wait until transmitter is ready for another character */
-#define TXWAITRDY(registers) \
-{ \
- ulong tmo = get_timer(0) + 1 * CONFIG_SYS_HZ; \
- while (((registers)->status_a & NETARM_SER_STATA_TX_RDY) == 0 ) { \
- if (get_timer(0) > tmo) \
- break; \
- } \
-}
-
-
-volatile netarm_serial_channel_t *serial_reg_ch1 = get_serial_channel(0);
-volatile netarm_serial_channel_t *serial_reg_ch2 = get_serial_channel(1);
-
-extern void _netarm_led_FAIL1(void);
-
-/*
- * Setup both serial i/f with given baudrate
- */
-void serial_setbrg (void)
-{
- /* set 0 ... make sure pins are configured for serial */
-#if !defined(CONFIG_NETARM_NS7520)
- PORTA = PORTB =
- NETARM_GEN_PORT_MODE (0xef) | NETARM_GEN_PORT_DIR (0xe0);
-#else
- PORTA = NETARM_GEN_PORT_MODE (0xef) | NETARM_GEN_PORT_DIR (0xe0);
- PORTC = NETARM_GEN_PORT_CSF (0xef) | NETARM_GEN_PORT_MODE (0xef) | NETARM_GEN_PORT_DIR (0xe0);
-#endif
-
- /* first turn em off */
- serial_reg_ch1->ctrl_a = serial_reg_ch2->ctrl_a = 0;
-
- /* clear match register, we don't need it */
- serial_reg_ch1->rx_match = serial_reg_ch2->rx_match = 0;
-
- /* setup bit rate generator and rx buffer gap timer (1 byte only) */
- if ((gd->baudrate >= MIN_BAUD_RATE)
- && (gd->baudrate <= MAX_BAUD_RATE)) {
- serial_reg_ch1->bitrate = serial_reg_ch2->bitrate =
- NETARM_SER_BR_X16 (gd->baudrate);
- serial_reg_ch1->rx_buf_timer = serial_reg_ch2->rx_buf_timer =
- 0;
- serial_reg_ch1->rx_char_timer = serial_reg_ch2->rx_char_timer =
- NETARM_SER_RXGAP (gd->baudrate);
- } else {
- hang ();
- }
-
- /* setup port mode */
- serial_reg_ch1->ctrl_b = serial_reg_ch2->ctrl_b =
- ( NETARM_SER_CTLB_RCGT_EN |
- NETARM_SER_CTLB_UART_MODE);
- serial_reg_ch1->ctrl_a = serial_reg_ch2->ctrl_a =
- ( NETARM_SER_CTLA_ENABLE |
- NETARM_SER_CTLA_P_NONE |
- /* see errata */
- NETARM_SER_CTLA_2STOP |
- NETARM_SER_CTLA_8BITS |
- NETARM_SER_CTLA_DTR_EN |
- NETARM_SER_CTLA_RTS_EN);
-}
-
-
-/*
- * Initialise the serial port with the given baudrate. The settings
- * are always 8 data bits, no parity, 1 stop bit, no start bits.
- */
-int serial_init (void)
-{
- serial_setbrg ();
- return 0;
-}
-
-
-/*
- * Output a single byte to the serial port.
- */
-void serial_putc (const char c)
-{
- volatile unsigned char *fifo;
-
- /* If \n, also do \r */
- if (c == '\n')
- serial_putc ('\r');
-
- fifo = (volatile unsigned char *) &(serial_reg_ch1->fifo);
- TXWAITRDY (serial_reg_ch1);
- *fifo = c;
-}
-
-/*
- * Test of a single byte from the serial port. Returns 1 on success, 0
- * otherwise.
- */
-int serial_tstc(void)
-{
- return serial_reg_ch1->status_a & NETARM_SER_STATA_RX_RDY;
-}
-
-/*
- * Read a single byte from the serial port. Returns 1 on success, 0
- * otherwise.
- */
-int serial_getc (void)
-{
- unsigned int ch_uint;
- volatile unsigned int *fifo;
- volatile unsigned char *fifo_char = NULL;
- int buf_count = 0;
-
- while (!(serial_reg_ch1->status_a & NETARM_SER_STATA_RX_RDY))
- /* NOP */ ;
-
- fifo = (volatile unsigned int *) &(serial_reg_ch1->fifo);
- fifo_char = (unsigned char *) &ch_uint;
- ch_uint = *fifo;
-
- buf_count = NETARM_SER_STATA_RXFDB (serial_reg_ch1->status_a);
- switch (buf_count) {
- case NETARM_SER_STATA_RXFDB_4BYTES:
- buf_count = 4;
- break;
- case NETARM_SER_STATA_RXFDB_3BYTES:
- buf_count = 3;
- break;
- case NETARM_SER_STATA_RXFDB_2BYTES:
- buf_count = 2;
- break;
- case NETARM_SER_STATA_RXFDB_1BYTES:
- buf_count = 1;
- break;
- default:
- /* panic, be never here */
- break;
- }
-
- serial_reg_ch1->status_a |= NETARM_SER_STATA_RX_CLOSED;
-
- return ch_uint & 0xff;
-}
-
-void serial_puts (const char *s)
-{
- while (*s) {
- serial_putc (*s++);
- }
-}
--
1.7.10.4
More information about the U-Boot
mailing list