[U-Boot] [PATCH 06/11] snowball: applying power to LAN and GBF controllers

[mathieu.poirier at linaro.org]

From: "Mathieu J. Poirier" <mathieu.poirier at linaro.org>

LAN and GBF need to be powered explicitely, doing so with
interface to AB8500 companion chip.

Signed-off-by: Mathieu Poirier <mathieu.poirier at linaro.org>
Signed-off-by: John Rigby <john.rigby at linaro.org>
---
 arch/arm/include/asm/arch-u8500/hardware.h |   11 +++-
 arch/arm/include/asm/arch-u8500/prcmu.h    |    7 ++-
 board/st-ericsson/snowball/snowball.c      |   87 ++++++++++++++++++++++++++++
 include/configs/snowball.h                 |    1 +
 4 files changed, 103 insertions(+), 3 deletions(-)

diff --git a/arch/arm/include/asm/arch-u8500/hardware.h b/arch/arm/include/asm/arch-u8500/hardware.h
index 9208880..8044ac3 100644
--- a/arch/arm/include/asm/arch-u8500/hardware.h
+++ b/arch/arm/include/asm/arch-u8500/hardware.h
@@ -62,7 +62,7 @@
 
 /* Per4 */
 #define U8500_PRCMU_BASE	(U8500_PER4_BASE + 0x07000)
-#define U8500_PRCMU_TCDM_BASE   (U8500_PER4_BASE + 0x06800)
+#define U8500_PRCMU_TCDM_BASE   (U8500_PER4_BASE + 0x68000)
 
 /* Per3 */
 #define U8500_UART2_BASE	(U8500_PER3_BASE + 0x7000)
@@ -80,4 +80,13 @@
 #define U8500_BOOTROM_BASE      0x9001f000
 #define U8500_BOOTROM_ASIC_ID_OFFSET    0x0ff4
 
+/* AB8500 specifics */
+#define AB8500_MISC		0x0010
+#define AB8500_GPIO_SEL2_REG	0x1001
+#define AB8500_GPIO_DIR2_REG	0x1011
+#define AB8500_GPIO_DIR4_REG	0x1013
+#define AB8500_GPIO_SEL4_REG	0x1003
+#define AB8500_GPIO_OUT2_REG	0x1021
+#define AB8500_GPIO_OUT4_REG	0x1023
+
 #endif /* __ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/include/asm/arch-u8500/prcmu.h b/arch/arm/include/asm/arch-u8500/prcmu.h
index 9862eb3..e9dcc93 100644
--- a/arch/arm/include/asm/arch-u8500/prcmu.h
+++ b/arch/arm/include/asm/arch-u8500/prcmu.h
@@ -64,8 +64,11 @@
 
 #define REQ_MB5			5
 
-extern int prcmu_i2c_read(u8 reg, u16 slave);
-extern int prcmu_i2c_write(u8 reg, u16 slave, u8 reg_data);
+#define ab8500_read	prcmu_i2c_read
+#define ab8500_write	prcmu_i2c_write
+
+int prcmu_i2c_read(u8 reg, u16 slave);
+int prcmu_i2c_write(u8 reg, u16 slave, u8 reg_data);
 
 void u8500_prcmu_enable(u32 *reg);
 void db8500_prcmu_init(void);
diff --git a/board/st-ericsson/snowball/snowball.c b/board/st-ericsson/snowball/snowball.c
index a70ebb1..7959ab8 100644
--- a/board/st-ericsson/snowball/snowball.c
+++ b/board/st-ericsson/snowball/snowball.c
@@ -25,6 +25,8 @@
 #include <asm/io.h>
 #include <asm/errno.h>
 #include <asm/arch/db8500_pincfg.h>
+#include <asm/arch/prcmu.h>
+#include <asm/arch/hardware.h>
 
 #include "db8500_pins.h"
 
@@ -183,3 +185,88 @@ int dram_init(void)
 
 	return 0;
 }
+
+static int raise_ab8500_gpio16(void)
+{
+	int ret;
+
+	/* selection */
+	ret = ab8500_read(AB8500_MISC, AB8500_GPIO_SEL2_REG);
+	if (ret < 0)
+		goto out;
+
+	ret |= 0x80;
+	ret = ab8500_write(AB8500_MISC, AB8500_GPIO_SEL2_REG, ret);
+	if (ret < 0)
+		goto out;
+
+	/* direction */
+	ret = ab8500_read(AB8500_MISC, AB8500_GPIO_DIR2_REG);
+	if (ret < 0)
+		goto out;
+
+	ret |= 0x80;
+	ret = ab8500_write(AB8500_MISC, AB8500_GPIO_DIR2_REG, ret);
+	if (ret < 0)
+		goto out;
+
+	/* out */
+	ret = ab8500_read(AB8500_MISC, AB8500_GPIO_OUT2_REG);
+	if (ret < 0)
+		goto out;
+
+	ret |= 0x80;
+	ret = ab8500_write(AB8500_MISC, AB8500_GPIO_OUT2_REG, ret);
+
+out:
+	return ret;
+}
+
+static int raise_ab8500_gpio26(void)
+{
+	int ret;
+
+	/* selection */
+	ret = ab8500_read(AB8500_MISC, AB8500_GPIO_DIR4_REG);
+	if (ret < 0)
+		goto out;
+
+	ret |= 0x2;
+	ret = ab8500_write(AB8500_MISC, AB8500_GPIO_DIR4_REG, ret);
+	if (ret < 0)
+		goto out;
+
+	/* out */
+	ret = ab8500_read(AB8500_MISC, AB8500_GPIO_OUT4_REG);
+	if (ret < 0)
+		goto out;
+
+	ret |= 0x2;
+	ret = ab8500_write(AB8500_MISC, AB8500_GPIO_OUT4_REG, ret);
+
+out:
+	return ret;
+}
+
+int board_late_init(void)
+{
+	/* enable 3V3 for LAN controller */
+	if (raise_ab8500_gpio26() >= 0) {
+		/* Turn on FSMC device */
+		writel(0x1, 0x8000f000);
+		writel(0x1, 0x8000f008);
+
+		/* setup FSMC for LAN controler */
+		writel(0x305b, 0x80000000);
+
+		/* run at the highest possible speed */
+		writel(0x01010210, 0x80000004);
+	} else
+		printf("error: can't raise GPIO26\n");
+
+	/* enable 3v6 for GBF chip */
+	if ((raise_ab8500_gpio16() < 0))
+		printf("error: cant' raise GPIO16\n");
+
+	return 0;
+}
diff --git a/include/configs/snowball.h b/include/configs/snowball.h
index bb8970b..e9de790 100644
--- a/include/configs/snowball.h
+++ b/include/configs/snowball.h
@@ -32,6 +32,7 @@
 #define CONFIG_SYS_ICACHE_OFF
 #define CONFIG_SYS_DCACHE_OFF
 #define CONFIG_ARCH_CPU_INIT
+#define CONFIG_BOARD_LATE_INIT
 
 /*
  * High Level Configuration Options
-- 
1.7.5.4