[U-Boot] [PATCH 2/2] exynos: smdk5250: Enable the pinmux setup

Simon Glass sjg at chromium.org
Fri Jun 1 02:37:23 CEST 2012


Hi,

On Wed, May 23, 2012 at 1:49 AM, Rajeshwari Birje <
rajeshwari.birje at gmail.com> wrote:

> Hi Chander,
>
> Thank you for comments
>



> On Wed, May 23, 2012 at 11:35 AM, Chander Kashyap
> <chander.kashyap at linaro.org> wrote:
> > Hi,
> >
> > On 4 May 2012 12:26, Rajeshwari Shinde <rajeshwari.s at samsung.com> wrote:
> >> Use the pinmux configuration function for SMDK5250.
> >>
> >> Signed-off-by: Abhilash Kesavan <a.kesavan at samsung.com>
> >> Signed-off-by: Rajeshwari Shinde <rajeshwari.s at samsung.com>
> >> ---
> >>  arch/arm/cpu/armv7/exynos/Makefile |    2 +-
> >>  board/samsung/smdk5250/smdk5250.c  |  160
> ++++++------------------------------
> >>  2 files changed, 26 insertions(+), 136 deletions(-)
> >>
> >> diff --git a/arch/arm/cpu/armv7/exynos/Makefile
> b/arch/arm/cpu/armv7/exynos/Makefile
> >> index 90ec2bd..9119961 100644
> >> --- a/arch/arm/cpu/armv7/exynos/Makefile
> >> +++ b/arch/arm/cpu/armv7/exynos/Makefile
> >> @@ -22,7 +22,7 @@ include $(TOPDIR)/config.mk
> >>
> >>  LIB    = $(obj)lib$(SOC).o
> >>
> >> -COBJS  += clock.o power.o soc.o system.o
> >> +COBJS  += clock.o power.o soc.o system.o pinmux.o
> >>
> >>  SRCS   := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> >>  OBJS   := $(addprefix $(obj),$(COBJS) $(SOBJS))
> >> diff --git a/board/samsung/smdk5250/smdk5250.c
> b/board/samsung/smdk5250/smdk5250.c
> >> index 32786e2..4c0398d 100644
> >> --- a/board/samsung/smdk5250/smdk5250.c
> >> +++ b/board/samsung/smdk5250/smdk5250.c
> >> @@ -26,6 +26,7 @@
> >>  #include <asm/arch/cpu.h>
> >>  #include <asm/arch/gpio.h>
> >>  #include <asm/arch/mmc.h>
> >> +#include <asm/arch/pinmux.h>
> >>  #include <asm/arch/sromc.h>
> >>
> >>  DECLARE_GLOBAL_DATA_PTR;
> >> @@ -35,72 +36,7 @@ struct exynos5_gpio_part1 *gpio1;
> > Do we need this declaration as gpio init is done using pinmux.
> > And remove the same from board_init.
> - will do so
> >>  static void smc9115_pre_init(void)
> >>  {
> >>        u32 smc_bw_conf, smc_bc_conf;
> >> -       int i;
> >> -
> >> -       /*
> >> -        * SROM:CS1 and EBI
> >> -        *
> >> -        * GPY0[0]      SROM_CSn[0]
> >> -        * GPY0[1]      SROM_CSn[1](2)
> >> -        * GPY0[2]      SROM_CSn[2]
> >> -        * GPY0[3]      SROM_CSn[3]
> >> -        * GPY0[4]      EBI_OEn(2)
> >> -        * GPY0[5]      EBI_EEn(2)
> >> -        *
> >> -        * GPY1[0]      EBI_BEn[0](2)
> >> -        * GPY1[1]      EBI_BEn[1](2)
> >> -        * GPY1[2]      SROM_WAIT(2)
> >> -        * GPY1[3]      EBI_DATA_RDn(2)
> >> -        */
> >> -       s5p_gpio_cfg_pin(&gpio1->y0, CONFIG_ENV_SROM_BANK,
> GPIO_FUNC(2));
> >> -       s5p_gpio_cfg_pin(&gpio1->y0, 4, GPIO_FUNC(2));
> >> -       s5p_gpio_cfg_pin(&gpio1->y0, 5, GPIO_FUNC(2));
> >> -
> >> -       for (i = 0; i < 4; i++)
> >> -               s5p_gpio_cfg_pin(&gpio1->y1, i, GPIO_FUNC(2));
> >> -
> >> -       /*
> >> -        * EBI: 8 Addrss Lines
> >> -        *
> >> -        * GPY3[0]      EBI_ADDR[0](2)
> >> -        * GPY3[1]      EBI_ADDR[1](2)
> >> -        * GPY3[2]      EBI_ADDR[2](2)
> >> -        * GPY3[3]      EBI_ADDR[3](2)
> >> -        * GPY3[4]      EBI_ADDR[4](2)
> >> -        * GPY3[5]      EBI_ADDR[5](2)
> >> -        * GPY3[6]      EBI_ADDR[6](2)
> >> -        * GPY3[7]      EBI_ADDR[7](2)
> >> -        *
> >> -        * EBI: 16 Data Lines
> >> -        *
> >> -        * GPY5[0]      EBI_DATA[0](2)
> >> -        * GPY5[1]      EBI_DATA[1](2)
> >> -        * GPY5[2]      EBI_DATA[2](2)
> >> -        * GPY5[3]      EBI_DATA[3](2)
> >> -        * GPY5[4]      EBI_DATA[4](2)
> >> -        * GPY5[5]      EBI_DATA[5](2)
> >> -        * GPY5[6]      EBI_DATA[6](2)
> >> -        * GPY5[7]      EBI_DATA[7](2)
> >> -        *
> >> -        * GPY6[0]      EBI_DATA[8](2)
> >> -        * GPY6[1]      EBI_DATA[9](2)
> >> -        * GPY6[2]      EBI_DATA[10](2)
> >> -        * GPY6[3]      EBI_DATA[11](2)
> >> -        * GPY6[4]      EBI_DATA[12](2)
> >> -        * GPY6[5]      EBI_DATA[13](2)
> >> -        * GPY6[6]      EBI_DATA[14](2)
> >> -        * GPY6[7]      EBI_DATA[15](2)
> >> -        */
> >> -       for (i = 0; i < 8; i++) {
> >> -               s5p_gpio_cfg_pin(&gpio1->y3, i, GPIO_FUNC(2));
> >> -               s5p_gpio_set_pull(&gpio1->y3, i, GPIO_PULL_UP);
> >> -
> >> -               s5p_gpio_cfg_pin(&gpio1->y5, i, GPIO_FUNC(2));
> >> -               s5p_gpio_set_pull(&gpio1->y5, i, GPIO_PULL_UP);
> >> -
> >> -               s5p_gpio_cfg_pin(&gpio1->y6, i, GPIO_FUNC(2));
> >> -               s5p_gpio_set_pull(&gpio1->y6, i, GPIO_PULL_UP);
> >> -       }
> >> +       int err;
> >>
> >>        /* Ethernet needs data bus width of 16 bits */
> >>        smc_bw_conf = SROMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK)
> >> @@ -112,6 +48,11 @@ static void smc9115_pre_init(void)
> >>                        | SROMC_BC_PMC(0x01);
> >>
> >>        /* Select and configure the SROMC bank */
> >> +       err = exynos_pinmux_config(PERIPH_ID_SROMC,
> >> +                               CONFIG_ENV_SROM_BANK |
> PINMUX_FLAG_16BIT);
> >> +       if (err < 0)
> >> +               debug("SROMC not configured\n");
>

Perhaps return -1 here?


> >> +
> >>        s5p_config_sromc(CONFIG_ENV_SROM_BANK, smc_bw_conf, smc_bc_conf);
> >>  }
> >>  #endif
> >> @@ -186,31 +127,12 @@ int checkboard(void)
> >>  #ifdef CONFIG_GENERIC_MMC
> >>  int board_mmc_init(bd_t *bis)
> >>  {
> >> -       int i, err;
> >> -
> >> -       /*
> >> -        * MMC2 SD card GPIO:
> >> -        *
> >> -        * GPC2[0]      SD_2_CLK(2)
> >> -        * GPC2[1]      SD_2_CMD(2)
> >> -        * GPC2[2]      SD_2_CDn
> >> -        * GPC2[3:6]    SD_2_DATA[0:3](2)
> >> -        */
> >> -       for (i = 0; i < 7; i++) {
> >> -               /* GPC2[0:6] special function 2 */
> >> -               s5p_gpio_cfg_pin(&gpio1->c2, i, GPIO_FUNC(0x2));
> >> +       int err;
> >>
> >> -               /* GPK2[0:6] drv 4x */
> >> -               s5p_gpio_set_drv(&gpio1->c2, i, GPIO_DRV_4X);
> >> -
> >> -               /* GPK2[0:1] pull disable */
> >> -               if (i == 0 || i == 1) {
> >> -                       s5p_gpio_set_pull(&gpio1->c2, i,
> GPIO_PULL_NONE);
> >> -                       continue;
> >> -               }
> >> -
> >> -               /* GPK2[2:6] pull up */
> >> -               s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_UP);
> >> +       err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
> >> +       if (err < 0) {
> >> +               debug("SDMMC2 not configured\n");
> >> +               return err;
> >>        }
> >>
> >>        err = s5p_mmc_init(2, 4);
> >> @@ -220,55 +142,23 @@ int board_mmc_init(bd_t *bis)
> >>
> >>  static void board_uart_init(void)
> >>  {
> >> -       struct exynos5_gpio_part1 *gpio1 =
> >> -               (struct exynos5_gpio_part1 *)
> samsung_get_base_gpio_part1();
> >> -       int i;
> >> +       int err;
> >>
> >> -       /*
> >> -        * UART0 GPIOs : GPA0CON[3:0] 0x2222
> >> -        * Must set CFG17 switches to select UART0 to use.
> >> -        */
> >> -       for (i = 0; i <= 3; i++) {
> >> -               s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE);
> >> -               s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2));
> >> -       }
> >> +       err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE);
> >> +       if (err < 0)
> >> +               debug("UART0 not configured\n");
> >>
> >> -       /*
> >> -        * UART1 GPIOs : GPA0CON[5:4] 0x22
> >> -        * Must set CFG17 switches to select UART1 to use.
> >> -        *
> >> -        * This only sets RXD/TXD, as RTS/CTS need a resistor soldered
> down
> >> -        * in order to use them (so that those pins can be used for
> I2C).
> >> -        */
> >> -       for (i = 4; i <= 5; i++) {
> >> -               s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE);
> >> -               s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2));
> >> -       }
> >> +       err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE);
> >> +       if (err < 0)
> >> +               debug("UART1 not configured\n");
> >>
> >> -       /*
> >> -        * UART2 GPIOs : GPA1CON[1:0] 0x22
> >> -        * Must set CFG17 switches to select UART2 to use.
> >> -        *
> >> -        * This only sets RXD/TXD, as RTS/CTS need a resistor soldered
> down
> >> -        * in order to use them (so that those pins can be used for
> I2C).
> >> -        */
> >> -       for (i = 0; i <= 1; i++) {
> >> -               s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE);
> >> -               s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2));
> >> -       }
> >> -
> >> -       /*
> >> -        * UART3 GPIOs : GPA1CON[5:4] 0x22
> >> -        * Must set CFG16 switches to select UART3 to use.
> >> -        */
> >> -       for (i = 4; i <= 5; i++) {
> >> -               s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE);
> >> -               s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2));
> >> -       }
> >> +       err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE);
> >> +       if (err < 0)
> >> +               debug("UART2 not configured\n");
> >>
> >> -       /*
> >> -        * There's no mux for UART4--it's internal only
> >> -        */
> >> +       err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE);
> >> +       if (err < 0)
> >> +               debug("UART3 not configured\n");
> >>  }
> >>
> >>  #ifdef CONFIG_BOARD_EARLY_INIT_F
> >> --
> >> 1.7.4.4
> >>
> >> _______________________________________________
> >> U-Boot mailing list
> >> U-Boot at lists.denx.de
> >> http://lists.denx.de/mailman/listinfo/u-boot
> >
> >
> >
> > --
> > with warm regards,
> > Chander Kashyap
> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > http://lists.denx.de/mailman/listinfo/u-boot
>
> Regards,
> Rajeshwari Shinde
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>


More information about the U-Boot mailing list