[U-Boot] [PATCH v2 09/10] tegra20: Remove CPU init code from tegra20 u-boot
Allen Martin
amartin at nvidia.com
Tue Jun 5 23:20:24 CEST 2012
This code is now included in the tegra20 SPL
Signed-off-by: Allen Martin <amartin at nvidia.com>
---
arch/arm/cpu/armv7/start.S | 2 -
arch/arm/cpu/tegra20-common/ap20.c | 262 +----------------------------------
arch/arm/cpu/tegra20-common/board.c | 27 +---
include/configs/tegra2-common.h | 4 -
4 files changed, 8 insertions(+), 287 deletions(-)
diff --git a/arch/arm/cpu/armv7/start.S b/arch/arm/cpu/armv7/start.S
index 261835b..786152f 100644
--- a/arch/arm/cpu/armv7/start.S
+++ b/arch/arm/cpu/armv7/start.S
@@ -133,7 +133,6 @@ reset:
orr r0, r0, #0xd3
msr cpsr,r0
-#if !defined(CONFIG_TEGRA2)
/*
* Setup vector:
* (OMAP4 spl TEXT_BASE is not 32 byte aligned.
@@ -149,7 +148,6 @@ reset:
ldr r0, =_start
mcr p15, 0, r0, c12, c0, 0 @Set VBAR
#endif
-#endif /* !Tegra2 */
/* the mask ROM code should have PLL and others stable */
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
diff --git a/arch/arm/cpu/tegra20-common/ap20.c b/arch/arm/cpu/tegra20-common/ap20.c
index 698bfd0..299f698 100644
--- a/arch/arm/cpu/tegra20-common/ap20.c
+++ b/arch/arm/cpu/tegra20-common/ap20.c
@@ -20,16 +20,10 @@
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
-
#include <asm/io.h>
-#include <asm/arch/tegra2.h>
-#include <asm/arch/ap20.h>
-#include <asm/arch/clk_rst.h>
-#include <asm/arch/clock.h>
#include <asm/arch/fuse.h>
#include <asm/arch/gp_padctrl.h>
#include <asm/arch/pmc.h>
-#include <asm/arch/pinmux.h>
#include <asm/arch/scu.h>
#include <asm/arch/warmboot.h>
#include <common.h>
@@ -68,233 +62,7 @@ int tegra_get_chip_type(void)
return TEGRA_SOC_UNKNOWN;
}
-/* Returns 1 if the current CPU executing is a Cortex-A9, else 0 */
-static int ap20_cpu_is_cortexa9(void)
-{
- u32 id = readb(NV_PA_PG_UP_BASE + PG_UP_TAG_0);
- return id == (PG_UP_TAG_0_PID_CPU & 0xff);
-}
-
-void init_pllx(void)
-{
- struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
- struct clk_pll *pll = &clkrst->crc_pll[CLOCK_ID_XCPU];
- u32 reg;
-
- /* If PLLX is already enabled, just return */
- if (readl(&pll->pll_base) & PLL_ENABLE_MASK)
- return;
-
- /* Set PLLX_MISC */
- writel(1 << PLL_CPCON_SHIFT, &pll->pll_misc);
-
- /* Use 12MHz clock here */
- reg = PLL_BYPASS_MASK | (12 << PLL_DIVM_SHIFT);
- reg |= 1000 << PLL_DIVN_SHIFT;
- writel(reg, &pll->pll_base);
-
- reg |= PLL_ENABLE_MASK;
- writel(reg, &pll->pll_base);
-
- reg &= ~PLL_BYPASS_MASK;
- writel(reg, &pll->pll_base);
-}
-
-static void enable_cpu_clock(int enable)
-{
- struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
- u32 clk;
-
- /*
- * NOTE:
- * Regardless of whether the request is to enable or disable the CPU
- * clock, every processor in the CPU complex except the master (CPU 0)
- * will have it's clock stopped because the AVP only talks to the
- * master. The AVP does not know (nor does it need to know) that there
- * are multiple processors in the CPU complex.
- */
-
- if (enable) {
- /* Initialize PLLX */
- init_pllx();
-
- /* Wait until all clocks are stable */
- udelay(PLL_STABILIZATION_DELAY);
-
- writel(CCLK_BURST_POLICY, &clkrst->crc_cclk_brst_pol);
- writel(SUPER_CCLK_DIVIDER, &clkrst->crc_super_cclk_div);
- }
-
- /*
- * Read the register containing the individual CPU clock enables and
- * always stop the clock to CPU 1.
- */
- clk = readl(&clkrst->crc_clk_cpu_cmplx);
- clk |= 1 << CPU1_CLK_STP_SHIFT;
-
- /* Stop/Unstop the CPU clock */
- clk &= ~CPU0_CLK_STP_MASK;
- clk |= !enable << CPU0_CLK_STP_SHIFT;
- writel(clk, &clkrst->crc_clk_cpu_cmplx);
-
- clock_enable(PERIPH_ID_CPU);
-}
-
-static int is_cpu_powered(void)
-{
- struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA2_PMC_BASE;
-
- return (readl(&pmc->pmc_pwrgate_status) & CPU_PWRED) ? 1 : 0;
-}
-
-static void remove_cpu_io_clamps(void)
-{
- struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA2_PMC_BASE;
- u32 reg;
-
- /* Remove the clamps on the CPU I/O signals */
- reg = readl(&pmc->pmc_remove_clamping);
- reg |= CPU_CLMP;
- writel(reg, &pmc->pmc_remove_clamping);
-
- /* Give I/O signals time to stabilize */
- udelay(IO_STABILIZATION_DELAY);
-}
-
-static void powerup_cpu(void)
-{
- struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA2_PMC_BASE;
- u32 reg;
- int timeout = IO_STABILIZATION_DELAY;
-
- if (!is_cpu_powered()) {
- /* Toggle the CPU power state (OFF -> ON) */
- reg = readl(&pmc->pmc_pwrgate_toggle);
- reg &= PARTID_CP;
- reg |= START_CP;
- writel(reg, &pmc->pmc_pwrgate_toggle);
-
- /* Wait for the power to come up */
- while (!is_cpu_powered()) {
- if (timeout-- == 0)
- printf("CPU failed to power up!\n");
- else
- udelay(10);
- }
-
- /*
- * Remove the I/O clamps from CPU power partition.
- * Recommended only on a Warm boot, if the CPU partition gets
- * power gated. Shouldn't cause any harm when called after a
- * cold boot according to HW, probably just redundant.
- */
- remove_cpu_io_clamps();
- }
-}
-
-static void enable_cpu_power_rail(void)
-{
- struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA2_PMC_BASE;
- u32 reg;
-
- reg = readl(&pmc->pmc_cntrl);
- reg |= CPUPWRREQ_OE;
- writel(reg, &pmc->pmc_cntrl);
-
- /*
- * The TI PMU65861C needs a 3.75ms delay between enabling
- * the power rail and enabling the CPU clock. This delay
- * between SM1EN and SM1 is for switching time + the ramp
- * up of the voltage to the CPU (VDD_CPU from PMU).
- */
- udelay(3750);
-}
-
-static void reset_A9_cpu(int reset)
-{
- /*
- * NOTE: Regardless of whether the request is to hold the CPU in reset
- * or take it out of reset, every processor in the CPU complex
- * except the master (CPU 0) will be held in reset because the
- * AVP only talks to the master. The AVP does not know that there
- * are multiple processors in the CPU complex.
- */
-
- /* Hold CPU 1 in reset, and CPU 0 if asked */
- reset_cmplx_set_enable(1, crc_rst_cpu | crc_rst_de | crc_rst_debug, 1);
- reset_cmplx_set_enable(0, crc_rst_cpu | crc_rst_de | crc_rst_debug,
- reset);
-
- /* Enable/Disable master CPU reset */
- reset_set_enable(PERIPH_ID_CPU, reset);
-}
-
-static void clock_enable_coresight(int enable)
-{
- u32 rst, src;
-
- clock_set_enable(PERIPH_ID_CORESIGHT, enable);
- reset_set_enable(PERIPH_ID_CORESIGHT, !enable);
-
- if (enable) {
- /*
- * Put CoreSight on PLLP_OUT0 (216 MHz) and divide it down by
- * 1.5, giving an effective frequency of 144MHz.
- * Set PLLP_OUT0 [bits31:30 = 00], and use a 7.1 divisor
- * (bits 7:0), so 00000001b == 1.5 (n+1 + .5)
- */
- src = CLK_DIVIDER(NVBL_PLLP_KHZ, 144000);
- clock_ll_set_source_divisor(PERIPH_ID_CSI, 0, src);
-
- /* Unlock the CPU CoreSight interfaces */
- rst = 0xC5ACCE55;
- writel(rst, CSITE_CPU_DBG0_LAR);
- writel(rst, CSITE_CPU_DBG1_LAR);
- }
-}
-
-void start_cpu(u32 reset_vector)
-{
- /* Enable VDD_CPU */
- enable_cpu_power_rail();
-
- /* Hold the CPUs in reset */
- reset_A9_cpu(1);
-
- /* Disable the CPU clock */
- enable_cpu_clock(0);
-
- /* Enable CoreSight */
- clock_enable_coresight(1);
-
- /*
- * Set the entry point for CPU execution from reset,
- * if it's a non-zero value.
- */
- if (reset_vector)
- writel(reset_vector, EXCEP_VECTOR_CPU_RESET_VECTOR);
-
- /* Enable the CPU clock */
- enable_cpu_clock(1);
-
- /* If the CPU doesn't already have power, power it up */
- powerup_cpu();
-
- /* Take the CPU out of reset */
- reset_A9_cpu(0);
-}
-
-
-void halt_avp(void)
-{
- for (;;) {
- writel((HALT_COP_EVENT_JTAG | HALT_COP_EVENT_IRQ_1 \
- | HALT_COP_EVENT_FIQ_1 | (FLOW_MODE_STOP<<29)),
- FLOW_CTLR_HALT_COP_EVENTS);
- }
-}
-
-void enable_scu(void)
+static void enable_scu(void)
{
struct scu_ctlr *scu = (struct scu_ctlr *)NV_PA_ARM_PERIPHBASE;
u32 reg;
@@ -312,7 +80,7 @@ void enable_scu(void)
writel(reg, &scu->scu_ctrl);
}
-void init_pmc_scratch(void)
+static void init_pmc_scratch(void)
{
struct pmc_ctlr *const pmc = (struct pmc_ctlr *)TEGRA2_PMC_BASE;
int i;
@@ -323,34 +91,10 @@ void init_pmc_scratch(void)
/* ODMDATA is for kernel use to determine RAM size, LP config, etc. */
writel(CONFIG_SYS_BOARD_ODMDATA, &pmc->pmc_scratch20);
-
-#ifdef CONFIG_TEGRA2_LP0
- /* save Sdram params to PMC 2, 4, and 24 for WB0 */
- warmboot_save_sdram_params();
-#endif
}
-void tegra2_start(void)
+void lowlevel_init(void)
{
- struct pmux_tri_ctlr *pmt = (struct pmux_tri_ctlr *)NV_PA_APB_MISC_BASE;
-
- /* If we are the AVP, start up the first Cortex-A9 */
- if (!ap20_cpu_is_cortexa9()) {
- /* enable JTAG */
- writel(0xC0, &pmt->pmt_cfg_ctl);
-
- /*
- * If we are ARM7 - give it a different stack. We are about to
- * start up the A9 which will want to use this one.
- */
- asm volatile("mov sp, %0\n"
- : : "r"(AVP_EARLY_BOOT_STACK_LIMIT));
-
- start_cpu((u32)_start);
- halt_avp();
- /* not reached */
- }
-
/* Init PMC scratch memory */
init_pmc_scratch();
diff --git a/arch/arm/cpu/tegra20-common/board.c b/arch/arm/cpu/tegra20-common/board.c
index a50b1b9..458a928 100644
--- a/arch/arm/cpu/tegra20-common/board.c
+++ b/arch/arm/cpu/tegra20-common/board.c
@@ -23,7 +23,6 @@
#include <common.h>
#include <asm/io.h>
-#include <asm/arch/ap20.h>
#include <asm/arch/clock.h>
#include <asm/arch/funcmux.h>
#include <asm/arch/pmc.h>
@@ -69,6 +68,11 @@ int dram_init(void)
{
/* We do not initialise DRAM here. We just query the size */
gd->ram_size = query_sdram_size();
+
+#ifdef CONFIG_TEGRA2_LP0
+ /* save Sdram params to PMC 2, 4, and 24 for WB0 */
+ warmboot_save_sdram_params();
+#endif
return 0;
}
@@ -80,27 +84,6 @@ int checkboard(void)
}
#endif /* CONFIG_DISPLAY_BOARDINFO */
-#ifdef CONFIG_ARCH_CPU_INIT
-/*
- * Note this function is executed by the ARM7TDMI AVP. It does not return
- * in this case. It is also called once the A9 starts up, but does nothing in
- * that case.
- */
-int arch_cpu_init(void)
-{
- /* Fire up the Cortex A9 */
- tegra2_start();
-
- /* We didn't do this init in start.S, so do it now */
- cpu_init_cp15();
-
- /* Initialize essential common plls */
- clock_early_init();
-
- return 0;
-}
-#endif
-
/**
* Set up the specified uarts
*
diff --git a/include/configs/tegra2-common.h b/include/configs/tegra2-common.h
index 8e2732a..28a9082 100644
--- a/include/configs/tegra2-common.h
+++ b/include/configs/tegra2-common.h
@@ -43,8 +43,6 @@
#define CONFIG_SYS_CACHELINE_SIZE 32
-#define CONFIG_ARCH_CPU_INIT /* Fire up the A9 core */
-
#include <asm/arch/tegra2.h> /* get chip and board defs */
/*
@@ -53,8 +51,6 @@
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_OF_LIBFDT /* enable passing of devicetree */
--
1.7.9.5
More information about the U-Boot
mailing list