[U-Boot] [PATCH 08/20] arm/km: correct init of 88e6352 switch in the reset_phy function
Valentin Longchamp
valentin.longchamp at keymile.com
Thu Jun 7 12:06:48 CEST 2012
This is achieved thanks to the support read/write regs for the external
88e6352 switch. The functions for this are added into an own file
managed_switch.c. This is compiled if the define CONFIG_KM_MANAGED_SW_ADDR
was set in the board setup. This define specifies the phy address.
Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
Signed-off-by: Holger Brunck <holger.brunck at keymile.com>
cc: Gerlando Falauto <gerlando.falauto at keymile.com>
cc: Prafulla Wadaskar <prafulla at marvell.com>
---
board/keymile/common/common.h | 6 +
board/keymile/km_arm/Makefile | 4 +
board/keymile/km_arm/km_arm.c | 26 +++++-
board/keymile/km_arm/managed_switch.c | 166 +++++++++++++++++++++++++++++++++
include/configs/km_kirkwood.h | 13 +++
5 files changed, 214 insertions(+), 1 deletions(-)
create mode 100644 board/keymile/km_arm/managed_switch.c
diff --git a/board/keymile/common/common.h b/board/keymile/common/common.h
index 6c1f640..49225b8 100644
--- a/board/keymile/common/common.h
+++ b/board/keymile/common/common.h
@@ -125,6 +125,12 @@ struct bfticu_iomap {
int ethernet_present(void);
int ivm_read_eeprom(void);
+
+int ext_switch_reg_write(const char *devname, u8 phy_addr, u8 port,
+ u8 reg, u16 data);
+int ext_switch_reg_read(const char *devname, u8 phy_addr, u8 port,
+ u8 reg, u16 *data);
+
int set_km_env(void);
int fdt_set_node_and_value(void *blob,
char *nodename,
diff --git a/board/keymile/km_arm/Makefile b/board/keymile/km_arm/Makefile
index aa51255..06079e9 100644
--- a/board/keymile/km_arm/Makefile
+++ b/board/keymile/km_arm/Makefile
@@ -31,6 +31,10 @@ LIB = $(obj)lib$(BOARD).o
COBJS := $(BOARD).o ../common/common.o ../common/ivm.o
+ifdef CONFIG_KM_MANAGED_SW_ADDR
+COBJS += managed_switch.o
+endif
+
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
SOBJS := $(addprefix $(obj),$(SOBJS))
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index f59ebfc..8f0a7c3 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -9,6 +9,9 @@
* (C) Copyright 2010
* Heiko Schocher, DENX Software Engineering, hs at denx.de.
*
+ * (C) Copyright 2011, 2012
+ * Valentin Lontgchamp, Keymile AG, valentin.longchamp at keymile.com
+ *
* See file CREDITS for list of people who contributed to this
* project.
*
@@ -35,6 +38,7 @@
#include <miiphy.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
+#include <asm/errno.h>
#include <asm/arch/kirkwood.h>
#include <asm/arch/mpp.h>
@@ -384,7 +388,27 @@ void reset_phy(void)
/* reset the phy */
miiphy_reset(name, CONFIG_PHY_BASE_ADR);
}
-#elif !defined(CONFIG_KM_PIGGY4_88E6352)
+#elif defined(CONFIG_KM_PIGGY4_88E6352)
+
+#if defined(CONFIG_KM_MANAGED_SW_ADDR)
+void reset_phy(void)
+{
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* enable autoneg on port 0 phy */
+ ext_switch_reg_write(name, CONFIG_KM_MANAGED_SW_ADDR, 0, 0, 0x3300);
+
+ /* egress broadcast franes on all macs, with forwarding */
+ ext_switch_reg_write(name, CONFIG_KM_MANAGED_SW_ADDR, 16, 4, 0x000f);
+ ext_switch_reg_write(name, CONFIG_KM_MANAGED_SW_ADDR, 20, 4, 0x000f);
+ ext_switch_reg_write(name, CONFIG_KM_MANAGED_SW_ADDR, 21, 4, 0x000f);
+}
+#endif
+
+#else
/* Configure and enable MV88E1118 PHY on the piggy*/
void reset_phy(void)
{
diff --git a/board/keymile/km_arm/managed_switch.c b/board/keymile/km_arm/managed_switch.c
new file mode 100644
index 0000000..482c18d
--- /dev/null
+++ b/board/keymile/km_arm/managed_switch.c
@@ -0,0 +1,166 @@
+/*
+ * (C) Copyright 2012
+ * Valentin Lontgchamp, Keymile AG, valentin.longchamp at keymile.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/errno.h>
+
+#define SMI_HDR ((0x8 | 0x1) << 12)
+#define SMI_BUSY_MASK (0x8000)
+#define SMIRD_OP (0x2 << 10)
+#define SMIWR_OP (0x1 << 10)
+#define SMI_MASK 0x1f
+#define PORT_SHIFT 5
+
+#define COMMAND_REG 0
+#define DATA_REG 1
+
+static int ext_switch_wait_rdy(const char *devname, u8 phy_addr)
+{
+ u16 command;
+ u32 timeout = 100;
+ int ret;
+
+ /* wait till the SMI is not busy */
+ do {
+ /* read command register */
+ ret = miiphy_read(devname, phy_addr, COMMAND_REG, &command);
+ if (ret < 0) {
+ printf("%s: Error reading command register\n",
+ __func__);
+ return ret;
+ }
+ if (timeout-- == 0) {
+ printf("Err..(%s) SMI busy timeout\n", __func__);
+ return -EFAULT;
+ }
+ } while (command & SMI_BUSY_MASK);
+
+ return 0;
+}
+
+int ext_switch_reg_read(const char *devname, u8 phy_addr, u8 port,
+ u8 reg, u16 *data)
+{
+ int ret;
+ u16 command;
+
+ ret = ext_switch_wait_rdy(devname, phy_addr);
+ if (ret)
+ return ret;
+
+ command = SMI_HDR | SMIRD_OP | ((port&SMI_MASK) << PORT_SHIFT) |
+ (reg & SMI_MASK);
+ debug("%s: write to command: %#x\n", __func__, command);
+ ret = miiphy_write(devname, phy_addr, COMMAND_REG, command);
+ if (ret)
+ return ret;
+
+ ret = ext_switch_wait_rdy(devname, phy_addr);
+ if (ret)
+ return ret;
+
+ ret = miiphy_read(devname, phy_addr, DATA_REG, data);
+
+ return ret;
+}
+
+int ext_switch_reg_write(const char *devname, u8 phy_addr, u8 port,
+ u8 reg, u16 data)
+{
+ int ret;
+ u16 value;
+
+ ret = ext_switch_wait_rdy(devname, phy_addr);
+ if (ret)
+ return ret;
+
+ debug("%s: write to data: %#x\n", __func__, data);
+ ret = miiphy_write(devname, phy_addr, DATA_REG, data);
+ if (ret)
+ return ret;
+
+ value = SMI_HDR | SMIWR_OP | ((port & SMI_MASK) << PORT_SHIFT) |
+ (reg & SMI_MASK);
+ debug("%s: write to command: %#x\n", __func__, value);
+ ret = miiphy_write(devname, phy_addr, COMMAND_REG, value);
+ if (ret)
+ return ret;
+
+ ret = ext_switch_wait_rdy(devname, phy_addr);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+int do_sw_reg_read(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ char *name = "egiga0";
+ u16 value = 0, phyaddr, reg, port;
+ int ret;
+
+ if (argc < 4)
+ return cmd_usage(cmdtp);
+
+ phyaddr = simple_strtoul(argv[1], NULL, 16);
+ port = simple_strtoul(argv[2], NULL, 10);
+ reg = simple_strtoul(argv[3], NULL, 10);
+
+ ret = ext_switch_reg_read(name, phyaddr, port, reg, &value);
+ printf("%#x\n", value);
+
+ return ret;
+}
+
+U_BOOT_CMD(
+ sw_reg_read, 4, 1, do_sw_reg_read,
+ "read the switch registers",
+ "<phyaddr> <port> <reg>\n"
+ );
+
+int do_sw_reg_write(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ char *name = "egiga0";
+ u16 value = 0, phyaddr, reg, port;
+ int ret;
+
+ if (argc < 5)
+ return cmd_usage(cmdtp);
+
+ phyaddr = simple_strtoul(argv[1], NULL, 16);
+ port = simple_strtoul(argv[2], NULL, 10);
+ reg = simple_strtoul(argv[3], NULL, 10);
+ value = simple_strtoul(argv[4], NULL, 16);
+
+ ret = ext_switch_reg_write(name, phyaddr, port, reg, value);
+
+ return ret;
+}
+
+U_BOOT_CMD(
+ sw_reg_write, 5, 1, do_sw_reg_write,
+ "write the the switch registers",
+ "<phyaddr> <port> <reg> <value>\n"
+ );
+
diff --git a/include/configs/km_kirkwood.h b/include/configs/km_kirkwood.h
index fbe714b..059fdbc 100644
--- a/include/configs/km_kirkwood.h
+++ b/include/configs/km_kirkwood.h
@@ -58,6 +58,7 @@
#define CONFIG_KM_FPGA_CONFIG
#define CONFIG_KM_PIGGY4_88E6352
+#define CONFIG_KM_MANAGED_SW_ADDR 0x10
/* KM_MGCOGE3UN */
#elif defined(CONFIG_KM_MGCOGE3UN)
#define CONFIG_IDENT_STRING "\nKeymile COGE3UN"
@@ -131,6 +132,18 @@
MVGBE_SET_GMII_SPEED_TO_1000 |\
MVGBE_SET_MII_SPEED_TO_100)
+/*
+ * There is no phy on the eth interface, but an external switch
+ * For kmcoge5un it is completely unmanaged, so we disable an access to it
+ * For km_nusa, we an MDIO(MII) interface that can configure the switch trough
+ * an indirect access, so we do not disable the MII
+ */
+#ifndef CONFIG_KM_MANAGED_SW_ADDR
+#undef CONFIG_MII
+#undef CONFIG_CMD_MII
+#undef CONFIG_RESET_PHY_R
+#endif
+
#endif
#ifdef CONFIG_KM_PIGGY4_88E6061
--
1.7.1
More information about the U-Boot
mailing list